Hi tere, I bougth an usb sync/charge cable on ebay, I use it for a couple of hours, It works well but now it's switch off by hiself and the right led is become red. I can't switch it on! do I burn it?
Possible solutions
1. Put the XDA in the cradle and charge it
If this does not help
2. Do a soft reset with the stylus, I have had one hang where I had to do this.
The red LED indicates a message or missed call.
Regards
Michael
thanks, I tryed to soft reset but it still doesn't work, I removed the battery and I recharged it in the craddle, now it works but i lost all my data becase when I insert the charge battery it does an total reset. I think the usb cable instead to recharge the battery decharge it.
usually when I have a missed call or a new message, the red let doesn't flash.
you cant use USB to charge XDA2!!!
the usb port only gives out 1amp max and it has to share that amp to all the devices connected on your pc via that usb port.
XDA 2 needs 2Amp to charge up
so charging via usb will drain the battery instead of charging it lol.
gaz
I charge my XDA 2 via USB and it works...
Hello all. anyone knows what the heck is going on ?
i have it pluged in to the ac charger. charge light is on and the starts charging. then all of a sudded it starts to loose power while charging. what fives ?
Hovhannes said:
Hello all. anyone knows what the heck is going on ?
i have it pluged in to the ac charger. charge light is on and the starts charging. then all of a sudded it starts to loose power while charging. what fives ?
Click to expand...
Click to collapse
Problems with charger physical connection may be?
Your cat or wifey plugging off (even slightly) the plug out of the power socket.
Or may be charger cable loose in the mini-USB slot on Universal?
Did the amber charging light also go out?
the htc shows charging but noting happens.
orange light is on
As I've noticed, charging is handled by ROM. When you reset your device it doesn't start until Windows Mobile greeting blue screen is displayed.
If the amber light is on, everything's fine on the physical part.
I suggest you soft reset your device and try charging again -- could be the piece of software responsible for charging hung or went into instable state.
Hi Guys
I have a problem with my TyTN at the moment.
My device is not charging.
Yesterday i put it in my Docking Station and wait a little time.
But Now the Tynt isnt charged.
I think ist a Problem with my TyTN Hardware.
I have all Power Supplys used they i have, but it doesent work.
Can you help me?
Its this a problem with the accu or a fuse on the circuit ?
Sorry for my broken english i hope you understand me.
Regards Patrik Laube
Hello,
first of all, try to soft reset the device.
If it fails, hard reset it.
If it doesn't work, go the service center.
Good luck
The above advice is fine. But you did not say if any of the LEDs are lit.
Do you get the red NO CHARGE LED?
Does your phone operate normally except for not charging?
Mike
Hello
My Phone is working fine but i cant charge it with the original HTC adapter.
I must load the accu with a special loader.
USB and Charge dont work....
And i have no warranty I cant send it to my operator.
When i plug in the USB Cable it doesent make everthing.
I think it was a to high voltage on the USB or the USB Ground ( - ) had a electrical Power for a litte moment.
Have you an idea?
Thanks for yur help.
Regards Patrik
I had a similar problem, which was sorted by a new rom, but I ascertained it was software problem when I realised it charged when powered off.
PatrikLaube said:
Hello
USB and Charge dont work....
And i have no warranty I cant send it to my operator.
Have you an idea?
Thanks for yur help.
Regards Patrik
Click to expand...
Click to collapse
hi,
try this: when your device is connected via usb, tab on the battery icon in the taskbar on you device, go to the register "advanced" and check/uncheck "When Device is turned on, do not charge the battery when connected to the pc"
thats it
greetz
mizi
I'm having an issue along these lines, also.
My phone has been working fine untill the other night when I tried to charge it via the wall electrical outlet. It will not charge at all, the battery has been drained to nothing and I can't turn it on. The yellowish light doesn't turn on when I plug it in like it used to.
I don't know if this is a battery issue or an issue with the USB connection inside of the phone. On a side note, when it did have power and I tried to connect it to the USB via the PC; it didn't work. The phone was on, but the computer didn't even notice the phone was plugged in. That leads me to believe it would be a connection issue; but I'm not quite sure.
If anyone has anything they can add to this I would appreciate it, thank you.
P.S. Bringing it to a service center is a bit out of the question in the mean time seeing as it was bought on eBay and funds are limited for the time-being.
MiZi666 said:
hi,
try this: when your device is connected via usb, tab on the battery icon in the taskbar on you device, go to the register "advanced" and check/uncheck "When Device is turned on, do not charge the battery when connected to the pc"
thats it
greetz
mizi
Click to expand...
Click to collapse
Hello, I cannot find the "When Device is turned on, do not charge the battery when connected to the pc" in my device. My Rom is WM6.1 CE OS 5.2.20273 cooked by dvha79_ddt.
My HTC TyTN has the sample problem, but i can use the USB to charge normally. It cannot work using my AC adapter Only when the device is open...
About your Battery Issue.
I'll tell you exactly why ur phone isnt charging anymore... If you have been charging it alot on the USB or pretty much any!! charging on the USB u have killed ur battery, never charge your phone on the USB it kinda sucks they should make these phones able to be Sync'd thru USB without a battery cause these batteries should not be powered thru the USB over Time... from syncing to your pc will kill these batteries i have noticed that when u sync this Tytn Ithru USB and the device is at say 70% it charges up to 100% pretty fast i would recommand to you and anyone who reads this dont sync your TYTN or any HTCC phone for to long to the USB Cause it will Trash your batteries Life down the road... Hope this was HELPFUL.
Cheers
Paul
PatrikLaube said:
Hello
My Phone is working fine but i cant charge it with the original HTC adapter.
I must load the accu with a special loader.
USB and Charge dont work....
And i have no warranty I cant send it to my operator.
When i plug in the USB Cable it doesent make everthing.
I think it was a to high voltage on the USB or the USB Ground ( - ) had a electrical Power for a litte moment.
Have you an idea?
Thanks for yur help.
Regards Patrik
Click to expand...
Click to collapse
hi, did anyone solve this problem ? ive got the same problem with my htc touch cruise, i think it charges when turned off but doesnt when on. the orange light doesnt turn on when i plug usb to charge it and it doesnt sync thru the PC neither.
Does anyone has a solution to this ?Thanks a lot!
does anyone has a solution to this ?
hi, did anyone solve this problem ? ive got the same problem with my htc touch cruise, i think it charges when turned off but doesnt when on. the orange light doesnt turn on when i plug usb to charge it and it doesnt sync thru the PC neither.
Does anyone has a solution to this ?Thanks a lot!
^I'm having the same problem with my herm200. I did the soft reset, hard reset changed ROMs but still the same problem. I don't think it's the usb connector because if it is it wouldn't have been able to charge the phone even if it's turned off. Before I'm able to charge it turned on but it would take a few minutes before the orange led turns on, but when I use the phone or if I receive a text the orange led would turn off it's like the charger disconnects but after a few minutes it would go back again. Now it just wouldn't charge turned on, sometimes it gets worse where it just wouldn't charge on or off.
Now I'm already planning to buy an external battery charger.
gypsygirl13 said:
^I'm having the same problem with my herm200. I did the soft reset, hard reset changed ROMs but still the same problem. I don't think it's the usb connector because if it is it wouldn't have been able to charge the phone even if it's turned off. Before I'm able to charge it turned on but it would take a few minutes before the orange led turns on, but when I use the phone or if I receive a text the orange led would turn off it's like the charger disconnects but after a few minutes it would go back again. Now it just wouldn't charge turned on, sometimes it gets worse where it just wouldn't charge on or off.
Now I'm already planning to buy an external battery charger.
Click to expand...
Click to collapse
Are you using an official 1000mA charger? (Not a 500mA one) 500mA ones work, but they are under-powered and can cause strange behaviour, like not charging whilst turned on or whilst on a call. Similar problems can be found with car-chargers that will not charge until the device is soft reset.
Mike
^no it's not the official charger, I have this usb wall charger called Power Juice (phone and mp3 charger).
Input Voltage: AC100-240V
Output Voltage: 5V
Output Current:1000mAh
Do you think it's because I'm not using the original charger?
fixed my charging problems
The boyfriend told me to try a new cable for my charger so he bought me a 5pin usb cable, tried it at home and it worked! I still need to turn off the screen sometimes but that's ok at least I don't have to turn off the phone anymore. Now my battery charges less than 3 hours.
Hold both SoftKeys and Then press the Power button
Or you can also hold both softkeys and then put your stylus into the reset hole.
answer why it does not charge through the usb
Sorry for the very very late response. Under electrical legislation all hand held electrical devices must be insulated and fused. Some of the chargers that you can purchase are sealed without fuse which indicates that the phone has a fuse contained within its circuitry (or there may be 2 fuses one in each device) .
The problem you have encountered is that you have connected your phone to a computer or mains supply to charge. There has been a surge in the electrical supply either on connection or by un-connecting from these supplies (e.g. connect to the computer as it is booting would see a 65w signal through the USB) and this more often than not blows the fuse which sits on the PCB (printed circuit board) just after the usb connection internally to the phone.
you can either have the fuse fixed for 20/25 gbp or you can purchase a new circuit board or you can use an external charger for the battery. As it is only the power input point that is faulty.
hope this helps
Since we are at this non-charging & battery issue, I would like to ask this question on the D838pro. My battery won't charge even after 24 hours of charging. The red LED blinks thru the whole process. The LED did not turn on to orange or green. It is the battery problem because my spare battery works well. I would like to know what is wrong with the battery as I am willing to strip down the battery. Could it be the battery circuit or wiring that had fired?
cyberdroxxx said:
Since we are at this non-charging & battery issue, I would like to ask this question on the D838pro. My battery won't charge even after 24 hours of charging. The red LED blinks thru the whole process. The LED did not turn on to orange or green. It is the battery problem because my spare battery works well. I would like to know what is wrong with the battery as I am willing to strip down the battery. Could it be the battery circuit or wiring that had fired?
Click to expand...
Click to collapse
Never tried stripping down a battery, some things... well, just don't seem worth it. However as a learning exercise it might be interesting. Without lots of testing on a good battery with a multimeter then I have no clue what the readings should be between all the contacts. (Now there's a little job for you) It is as likely the internal structure of the battery is screwed as it is to be a wiring problem.
If you solve it you can certainly report back here
Mike
Hi !
I searched already around the forum, but I didn't find anything for my problem:
Yesterday my device turned off because of low battery (while listening music), then I tried to charge it with the original charger over night. Today in the morning the device was not charged but the amber/organge LED was blinking.
When I put on the charger the red led turns on, after a few seconds the amber led starts blinking then after a few minutes the led turns again red an then again blinking amber and so on ...
I can boot up Windows mobile bu after a few secounds the deivce turns off an then again red led an blinking amber ...
I did a softreset and a hardreset but still no charging.
I tried another battery from a neighbour, the device works fine, but still a blinking amber led (not always-on) when connect on the charger.
Can anybody help me ?
Sorry for my bad english ..
Have you tried using your friend's phone charger?
The problem has been discussed. It is known as the RLOD (Red light of Death) and is reported against many different phones and brands. It is likely a fault in:
1
The phones charging circuit
OR
2
A faulty battery
OR
3 A faulty USB port (bent pin or cracked solder joint)
OR
4
A cracked solder joint between the battery connector and m/board
In my experience it is most likely to be a faulty (stuck) charging circuit.
The following link may be useful, and it is worth persevering. I once had a phone that took several days to get started again:
http://forum.xda-developers.com/showthread.php?p=1077622#post1077622
Mike
@gypsygirl: I tried two different chargers which are working fine which another device (xda neo)
@mikechannon:
I think its a problem with the charging circut or the usb port (otherwise the data connection works when connected to the pc).
I tried the battery from my friend with 90 % battery left and put on the charger and ist doesn't start charging, only blinking amber ...
I guess I will buy an external cradle for charging the battery, not the best way, but so i can use the device ...
When there is any solution for a cracked charging circut, i will try it out ...
Thanks for help
Hi guys,
Suddenly facing a strange problem since last night.
My x10i was running out of charge & i connected to the comp to charge while i was working. I noticed the charging speed was extremely low, so i restarted the phone to see if it would help. Did not.
Thought there is some problem with the cable, used a different cable as well, but no use.
The slow charging had stopped and eventually the phone died.
Tried connecting to the socket & charging, still no use.
The red led blinks when i connect the phone to a charger via the usb or the socket.
needless to say the phone does not even boot up now, obviously for no charge...
any ideas wat maybe wrong or wat i could do ?
please advice
Have you tried to let it charge for some time in off mode? As long as your battery is not dead, and the phone get the right voltage through the USB connector it should charge in an "emergency mode". This is a slow way of charging, but allows for charging without any electronic circuits to monitor it, it is not the same as the charging screen that usually displays when you connect the phone while it is powered off. Usually when a phone is completely discharged it needs to be connected at least 15 min, sometimes a lot longer, before the electronics kicks in, and starts the speedcharging.
My best advise would be to connect it to the mains charger, or a USB port you KNOW supplies power. Some laptops cut down on the powersupply to the USB ports when they run on battery. Let it be connected for a long time (several hours), and then try to power it on again.
If that does not help three things can be wrong
1. Somewhere the USB connection is broken, either in the cable or in the connector on your phone (or on the PC's connector, but that is less likely).
2. The battery is dead, modern batteries contain circuits that actually disables the battery when any given parameters gets outside the defined limits. This is to prevent the battery catching fire. On some batteries this renders the battery useless, and you need a new battery.
3.) The mainboard of your phone is dead, and hence nothing works, can be ruled out if you can borrow a battery from someone to test if your phone works then.
I hope a good and long charge can sort out your problem, that is the easiest fix, and it is free.
Hi O_K,
well, i have been charging (or trying to) the phone since it died last night.
i have used different chargers & different modes of charge (through the system & the wall socket) - no joy at all.
the LED blinks red a couple of times when connected.
Very occasionally, the SONY ERICSSON logo (startup) shows on the screen & it switches off again, back to the blinking.
So charging for a long time & through different chargers has not helped.
gonna try a different battery now to see if that can help.
Thanks for your response!
well, tried switching chargers & batteries.
The problem seems to be with the charging unit on the phone (USB)
with any charger or battery, wen connected the led blinks (like wen the phone is charging), but there is no charge happening.
eventually the phone dies, even if charging
any ideas?
There is a thread some where in this forum for fixing the same problem you have...I don't remember the exact name of the thread..if I find it I'll post the link here..Anyways what the guy did was
-Pull the battery out and connect the charger till the led turns green.
-put in the battery now and charge the phone...
and I think that was it.
Hope it helped..
EDIT: Found the link.
http://forum.xda-developers.com/showthread.php?t=944322