Bluetooth Problem with Handsfree Profile in Car - Touch Cruise ROM Development

Hey Folks,
I have been reading some posts here about BT and/or BT Mute problems, but my issues seems to be a bit different, plust I didn't have it 1-2 Months ago, so I think it might be ROM/Radio upgrade related ...
Right now I am running udK Diamond R8 which works perfectly fine in general.
I got my phone hooked up via BT to my car BT handsfree (it's a Peugeot 207cc which uses some Parrot BT stuff I think). This used to work perfectly fine when I first started using the polaris in the car. I don't remember when the problem started to appear, but now, when I receive and accept an incoming call, it takes 4-5 seconds, till the polaris switches audio to handsfree, meaning after accepting the call, I can't hear the other party on my car speakers ... but I can hear sound from the regular polaris speaker, very quietly of course.
After those 4-5 seconds, everything is fine and the call is switched to the car handsfree set.
The BT connection to the car set is fine all the time ... no problems connecting or pairing.
Anyone experiencing similiar issues?
boba

Hi,
I have exactly the same problem with my C4 BT handsfree system (Parrot BT components) for some months ago. I have had a look at a lot of forum, but no answer and no solution.
Some days ago, I flash my HTC Polariswith the original WM6.1 Fre, but no improvement. I still have the same problem, 4/5 seconds before hearing the caller.
(PS : sorry for my poor english )
Bemi

Same for me, it worked fine before with the original ROM
ROM : 1.25.406.1 FRE dated 12/12/07
Radio : 1.58.21.23
Protocole : 25.65.30.04H
It happened suddenly.
I tryed a lot of modifications in the register, but no improvement.
I hoped to resolv this problem with the new original WM6.1 but no improvement.
Next week, Citroen will change the radio (it stops working many time a day).
I hope this will resolv the problem.
Bemi

I don't know excatelly the model, but it's the one with Bi-Tuner, BT, MP3 and without Navidrive.
Bemi

Same for me "and without Navidrive"
Probably the RD4
Bemi

Today, I tried several other mobiles (Samsung, Sony-Ericson, Eten, Alcatel) for my problem of delay with incoming calls.
All of them work properly and, as soon as I receive and accept an incoming call, the sound switches directly to the handsfree of the car.
So, what is the problem with my HTC Cruise ?
Any idea ?
Bemi

i'm having the same problem with a Sony DR-BT20NX headset
It has been working earlier.
But now , on incoming calls , the phone ring and later i ear a little signal in the bluetooth headset.
To accept the call , i've to use phone buttons ) .
The sound comes out the phone .I've to speak in the phone.
Otherwise i can listen music with the BT headset and make outgoing calls.
Rom : M-Amine 2.FRE
Radio : 1.59.42.15
( same problems with PDA viet Rom's V33 à V35 )
I don't remember if i've the problem since i've upgraded to radio 1.59.42.15 , sorry
Never had answers on differents forums ..

BT Joined Stereo
install advance config tool v3.3
go to BT setting
verify that your option is Joined stereo and not mono

I'm using udK Diamond R8. I had a lot of problems with my Parrot ck3100 carkit. It was finally resolved by installing the Murata 1.58.21.23 radio. With the for R8 recommended radio I had bad GSM reception, BT connection failure, random BT mute, Parrot displaying the call would continue when I in fact hang up etc.

Hi,
No change with Advanced Config Tools V3.3
Bemi

I have a different BT problem.
i am currently running Touch-IT m2d Beta. but i have always had this problem, even on the original official rom.
i pair my phone with a JVC KD-BT1 CD Head Unit in the car.
i sent this to HTC support (before i started flashing new roms to my cruise):
------------
HTC Touch Cruise. rom: 1.26.710.1 wwe radio: 1.58.21.23 protocol: 25.65.30.04h. bluetooth problem. when i have BT enabled on the htc, i get in the car and it pairs with my audio system. after i make the first call it disconnects (stops pairing) after the call is finished and then after 60 seconds, it pairs up again and i can make a call again. this happens after every call. i had a nokia and i-mate jasjam before with no problems whatsoever. any patch or update available?
------------
AND THIS WAS THEIR REPLY:
-------------
Bluetooth should be universal or is marketed as universal although it is far from the truth. Certain chipsets conflict or are incompatible with others. If a device is not fully compatible it will not offer all features or possibly not connect at all. I have included the below for current tested devices.
-------------
I DON'T think this is going to be fixed any time soon, so i'll live with it!

Hi every body.
I've got the same problem.
A Cruise Rev B, and a BT car's Kit (included in a peugeot, I thing a RD4/parrot stuff)
Actually my first call is ok, and then, heads phones are cutted (sometimes after 3 or 4 seconds), but my microphone still works.
My car's BT is still paired, and sometimes indicates that I'm still phoning, even if I've cutted it on my phone.
I'm happy to find some user's in the same "panade" than me, but I hope we will find a solution...
Who knows how it works and communicate?

It has to be radio problem.
Originally I had WM 6.0 Pro on my Polaris, and BT was working flawlessly.
Then I was stupid enough to upgrade to 6.1 WWE, and now I have all kind of trouble with BT connectivity. Downgrading back to 6.0 DID NOT help!

InSomNiaK said:
A Cruise Rev B, and a BT car's Kit (included in a peugeot, I thing a RD4/parrot stuff)
Actually my first call is ok, and then, heads phones are cutted (sometimes after 3 or 4 seconds), but my microphone still works.
My car's BT is still paired, and sometimes indicates that I'm still phoning, even if I've cutted it on my phone.
Click to expand...
Click to collapse
I have exactly the same problem, based on a slightly different configuration:
My car is a Citroen (with the RD4/parrot factory built in BT)...
My phone is a HTC TyTNII.... with WM6 I couldnt even pair the phone, so I upgraded to WM6.1
Actually I had to drive to the workshop to cut the power on the car, because the parrot BT unit wouldnt stop even tho my phone was off in the meantime.
I start to believe this is not a problem caused by my phone, but a fault SW version on the parrot unit.

I have pioneer deh-p7000bt and it works flawlessly with my polaris in handsfree and a2dp mode.
to have better quality i have to turn srs wow hd off.
in advanced config i set:
-use joint stereo: no
-bitpool: very high
-max bitpool: 64
-min bitpool: 32
-sample rate: 44100
-audio getaway: enabled

Is there anyone who solved this problem yet? I have the exact same problem. When someone calls me, I cannot hear the other party through my car speakers (Citroën C5 newest model without navidrive)

I just tried http://www.jetwaremobile.com/ and this seemed to solve my problems. I had to restart my TC after installing this and removed the relationship in my car. After I made a new relationship (pairing) everything seems to work fine. If this changes I'll let you know.

I am having the same trouble, which started after upgrading to WM 6.1. Am I right in understanding that the Bluetooth is controlled by the Radio ROM and if so is it possible to downgrade just the Radio ROM? I think mine originally came with 1.58.25.14 and the upgrade replaced it with 1.59.42.15, is there a procedure to do this, and has anyone had any success.

Sorry had a search and found http://forum.xda-developers.com/showthread.php?t=381600 which shows how to install just radio ROM, am just unclear as to whether you need to install Hard-SPL first as it is an official ROM and as to if changing radio clears all personal data from the phone.

I use to have a similar problem with the 4-5 second delay. i found that once the car is paired up with the phone, i ran bluetooth audio toggle, or other bluetooth audio program which makes all audio go through the vehicle all the time, including GPS navigation. This way when the phone rings, the ringtone can be heard through the speaker and when you answer it will be instantanious....... in theory.......... i mean, it worked for me anyway....
Then all you have to do is find some way to auto run the toggle everytime you pair your device to the vehicle...

Related

TyTN bluetooth car kit issues

Hi everybody,
I completed some tests using my bluetooth car kit (Audi integrated BT MMI car kit). Here is what I saw :
With the original french ROM (1.18.256.2)
Outgoing calls
90% of the calls were interrupted during dialing or connection. The main problem was UMTS stability with the french mobile operator named SFR. After deactivating UMTS/3G and falling back to GSM, 80% of the calls were interrupted during the first minute of communication because of BT unstability.
Incoming calls
Impossible to take a call : half were immediatly interrupted, half were answered using the internal micro instead of the BT one.
With the JasJam ROM (1.20.305.3)
Outgoing calls
After deactivating UMTS/3G support all the calls are stable. Every thing is working fine and the Audi BT car kit works just fine !
Incoming calls
Still impossible to take a call : quite all are not well handled. BT is still unusable to take calls.
I don't think the BT car kit is the problem, because I am using it every day with a Qtek 8310 (Tornado) and both incoming and outgoing calls are well handled.
If you've got some experience, please share it. I am so disapointed that this marvelous TyTN cannot replace my Tornado, only because this "merdique" (<------ french romantic word ) bluetooth functionnality is not working ! :evil:
Arnaud.
Hi Arnaud,
I too have problems - see:
http://forum.xda-developers.com/viewtopic.php?t=61594
Paul
Im also having problems with carkit.
Jasjam and kjam just dont connect with my carkit (while they pair with it) but Jasjam and all nokia / samsung phones work perfectly well with it. Even Palm treo 650 works.
Is this a problem with iMate sets or with Windows Mobile 5.0?
I've had a friend who also has a TyTN which we tried in my kit and it didn't work. It seems that users with other variants (e.g. Orange) don't have this issue?
Further (non-technical) tests have shown that if you answer or make a call, you can get the audio by going into the call menu and choosing "Turn handsfree off". My uneducated guess here is that there is some issue with the headset feature on the TyTN and by doing this, it resets the headset profile and bingo!
It is a pain in the ar$e doing this for inbound calls, but for outbound it is manageable - you simply dial the number and whilst it is connecting, do the menu->Turn handsfree off workaround. Hopefully the new ROM will fix it - when it arrives!!
Hi All,
Just to put in my experience.
I have an Audi A4 with a Gen II car kit. As there is no handset holder for the TyTn I am using the Bluetooth function.
I have the Orange SPV M3100 variant, which works absolutley fine with the Audi Bluetooth, with one problem....
As I don't yet have a car charger, when the phone goes into sleep mode, it appears to disable bluetooh (I occasionally get a 'BT OFF' signal on the car display). Switching off bluetooth, then switching on again on the phone tends to kick it back into life where it stays live for another ten minutes or so until the phone dozes off again..
I have heard of a few people who have also diagnosed the problem as possbily the phone going to sleep to conserve battery, and solved the problem with an in car charger. I will report back when I have a charger.
Again, I do not suspect the Audi car kit as I have previoulsy used this (on Bluetooth) with a Nokia 6230 and MDA Vario, with no problems at all (the Vario was externally powered from the car).
Maybe you TyTn owners can flash to the Orange ROM ;-)
Same Scenario Different Cast
I have a Lexus GS with BT.... here's my Undesired results
actually, the only Problem i am having is very annoying.
If i receive or make a call after i pair with the Car kit, EVERY Thing is fine,
The sound quality is good, the response time is good (no Delay).
BUT after that call is ended, the BT itself on the jasjam TURNS off...
so i have to turn the BT on After EVERY Single Call (either made or received)
Is this Normal, I don't think so, but i had to ask
I have the Original Ship ROM Arabic version
My BMW handsfree works just fine with my TyTN. No issues other than an occasional BT off (loss of pairing). Interestingly, it's not sleep mode related since it usually works just fine in that mode. Generally, disabling Bt then re-enabling it re-establishes the connection then all is well. I have no issues making or receiving calls.
No doubt CarKit issues will be addressed when HTC releases their ROM update. Recent information tells me that this update is pretty much guaranteed to be an AKU3.0 variant. There's a tremendous amount of BT stack improvements in this AKU that should improve this as well as A2DP bluetooth issues.
.. No issues other than an occasional BT off (loss of pairing). ..
Interesting! I have the same issue with MTeoR.. I wonder if MteoR and TyTn are based on the same HTC device PLATFORM.
Updated my Parrot CK3100 to the newest version and things still don't work too well. When I start a call on the Parrot it takes around 20 seconds to start dialing on the phone, and when I receive a call I have to pick it up, place it on hold, and retrieve from hold to be able to hear the other side.
I wonder what/why they changed in the Bluetooth stack, it worked perfectly on my Wizard...
Renault Laguna II integrated BT kit
Works OK with my Laguna system except for the signal strength indicator. It appears that this information is not sent or translated onto the screen in the car.... Calls are fine though, and I noticed that the car rings immediately, the moment the phone does. Could be because the TyTN has the "turbo lag" explained in another thread tho
Cheers
rmorby said:
Works OK with my Laguna system except for the signal strength indicator. It appears that this information is not sent or translated onto the screen in the car.... Calls are fine though, and I noticed that the car rings immediately, the moment the phone does. Could be because the TyTN has the "turbo lag" explained in another thread tho
Cheers
Click to expand...
Click to collapse
Try installing Jetware mobile extender, that adds signal and battery bars as well as network name.
I enabled Remote SIM Acces in the Bluetooth Menu and now my contacts sync on my Audi Bluetooth Car kit with WM 6.1.

Update to B&B 4.0 = carkit not working properly

Hello,
I have a question. I updated my original ROM to the B&B 4.0 ROM and it all looks super. But now when i slide the phone into my carkit ( Carcomm CHFS-97 wired carkit ) it mutes my radio and wont come un-mute until i take out the phone. I had no problem with this with my original ROM ( 1.2.404.1 NLD ).
I tried the phone of a friend of mine that purchased it at the same time as i did and that still works fine ( still has original ROM ).
Is there a way to somehow change settings so that the phone generates a proper mute signal again ?
How is a mute signal for a carkit actually generated by the phone ?
Thanks for your time,
Radio mutes, even without phone
I have the same problem.
The carcomm carkit is connected with the radio in the car thourgh several cables.
One of them is a mute cable.
When you receive a call, your telephone sends out a mute signal through the mute cable to your radio.
The problem with the laters update is caused by HTC.
The newest rom causes a constant mute signal that is being send by the phone.
3 solutions according to the supplier:
1 Let the phone hang in the carkit and press it down when you receive a call.
2 disconnect the mute cable
3 downgrade the firmware
My fourth option:
4 find a way to disable the mute signal
Anybody knows how????
I'm a littlebit further.
When you disable the phone (commanager).
Slide it into the carcomm carkit.
And then enable it again.
Then the mute signal seems to behave accordingly.
Still no idea to disable the mute signal before sliding it into the carkit.
Carcomm carkits
Regarding the mute issue's for the S710, P3300 & P4350.
Carcomm are developing a software patch to solve this problem with these devices.
It seems there is somewhat a problem in the new Roms from HTC..
I´ve sold quite a lot off these kits..and the problem with mute on constantly came with the latest ROMS from HTC...
same applies to the parrot bluetooth kits.

Problem with bluetooth handsfree

Hi,
I have a Vodafone P3600 which I had unlocked and flashed to test both HTC WM5 and Faman WM6 3.3 and 3.4. I have a problem using it with my Parrot CK3100, and it's the following: devices pair perfectly, but when I leave my car and then return, most of times P3600 does not connect with handsfree. Sometimes, it does connect, but after a long time. This occurs with any OS version I have tested.
A problem with CK3100 is discarded because I have flashed it with latest software version, and it was tested with a HP RW6815.
I tried disabling power saving, setting bluetooth as discoverable, installing Jetware, but nothing made it work as it should.
I'm near to sell my P3600 and buy a new HTC Touch only to solve this problem, because I need much a handsfree working in my car.
Can any of you give a hint of what the problem could be?
Thanks.
I forgot to say that if I power on my HTC, it always connect to the Parrot. But when it's in standby sometimes connects and others no.
I have an SonyEricsson HBH-DS200 and this works unfortunately with the P3600 also in a from you described way. I tryed AWE and PDAVIET and also AX3L ROMs.
Other points and problems with BT HandsFree are:
1.) A litle icon to show that the BT HansFree is connected will be showed in the status only after the first paaring. After that, nothing shows you, that the BT HansFree is connected (and therefor can be used) or not.
2.) After a phone call the BT HandsFree will be disconnected.That meanns, that I can not hear the phone ring in the earpice. I only hear it from the P3600. I have 2 choises after that:
a.) If I push te Answer button on the P3600, the voice is on the P3600.
b.) If I push the Answer button on the BT HansFree then the voice is on the BT HansFree (but it will be disconnected after the call).
3.) The volume can not be changed if I use the BT HandsFree. That means, the volume slide bar can be moved/changed, but this has no effect to the volume in the BT HansFree.
In my opinion if the paaring is done and the BT HandsFree is switched on it should be always:
- connected
- an icon in the status line appear
- the voice in the BT HandsFree - independent if the answer button is pushed on the phone or on the BT HandsFree
For me is the BT HandsFree very imortant, and I am a litle bit disappointed, that a device for 500 Eur works that buggy with a technology that is almost 10 year old.

Bluetooth issue still exists after new R2A ROM-update

Hi there,
Finally I assume I found out why some people have problems with their unit using BT and others not.
Those, who use BT headsets only (not stereo) and don't use the AD2P and AVRCP Profile don't have any problems. (I can confirm this - tested it with HBH-660 and Motorola without any troubles!)
And those people who have a stereo headset like the HBH-DS980 (which I own personally) and/or do own a car radio that can receive AD2P signals to transfer Stereo sound, face with the BT disconnections while listening to music and/or during a call or just right after...
So I think SE should solve this issue quickly as it seems to be a problem in WMP 6.1 in accordance to X1 hardware with AD2P / AVRCP profile devices.
So I start a poll for anyone who could confirm this or not !
BTW: I am using the Generic AT ROM but this BUG is affected through all other ROMs too, so that shouldn't matter -
Thanks,
Freako
My kenwood headunit uses avrcp and a2dp and works fine.
There was a discussion on this issue already and it does exist w/ my AT&T Tilt (Kaiser) as well w/ all the A2DP headsets I tried (SE DS220/205/980, JVC BT-1, ClipD R Radio, Jabra (forget what model)) so far
I believed the bluetooth issue that R2A fixed is another one where BT will turn itself off if not use for a while.
The 'turn off' issue is still there with mine! I had it only after 2,3 days but then continuously turn off by itself! Now, still happening! Generic_UK R2A
Generic Swedish R2A.
No problem for Bluetooth! But when I softreset x1 via spb mobile shell panell it crashes on boot.
jackleung said:
There was a discussion on this issue already and it does exist w/ my AT&T Tilt (Kaiser) as well w/ all the A2DP headsets I tried (SE DS220/205/980, JVC BT-1, ClipD R Radio, Jabra (forget what model)) so far
I believed the bluetooth issue that R2A fixed is another one where BT will turn itself off if not use for a while.
Click to expand...
Click to collapse
Yes absolutely Jackleung, you're right, the new firmware should have fixed the automatic turn off of BT only, but I belive what michaelthemage said, that it still exists after his UK firmware update so do I - today the BT icon dissapeared suddenly - so it was turned off automatically ... very curious...
Anyway, Jackleung, you say that this problem was present in earlier WM6 machines like the Kaiser? As far as I know I did not try a stereo BT headset on my previous Tytn II but you say it seems to be a bug in WM6.1 in general, right ?
Very interesting that trinode doesn't have these problems with it's Kenwood headset - maybe I give it a try if it isn't too expensive -
On the other way Persian Boy links it with the SPB Shell - I do have the standard SBP Panel that you can download from web. Maybe I should uninstall it and try again - maybe the SPB panel makes these troubles? Personally I can't imagine, but will try anyway -
So far,
Freako
trinode said:
My kenwood headunit uses avrcp and a2dp and works fine.
Click to expand...
Click to collapse
Can you please tell me the exact brand of this headunit by kenwood?
So you did try transferring music to the kennwood radio and there were no problems like sudden disconnections or so?
Thanks,
Freako
Freako said:
Yes absolutely Jackleung, you're right, the new firmware should have fixed the automatic turn off of BT only, but I belive what michaelthemage said, that it still exists after his UK firmware update so do I - today the BT icon dissapeared suddenly - so it was turned off automatically ... very curious...
Anyway, Jackleung, you say that this problem was present in earlier WM6 machines like the Kaiser? As far as I know I did not try a stereo BT headset on my previous Tytn II but you say it seems to be a bug in WM6.1 in general, right ?
Very interesting that trinode doesn't have these problems with it's Kenwood headset - maybe I give it a try if it isn't too expensive -
On the other way Persian Boy links it with the SPB Shell - I do have the standard SBP Panel that you can download from web. Maybe I should uninstall it and try again - maybe the SPB panel makes these troubles? Personally I can't imagine, but will try anyway -
So far,
Freako
Click to expand...
Click to collapse
The problem I am talking about is A2DP/Headset disconnected after phone call, and I have to re-connect it after that. I don't thinks it's WM6 or SPB panel issue since only HTC devices (X1, Kaiser w/ no SPB install) have this issue. My other device Asus P525 (WM6/6.1 w/ Widcomm bt stack) or Eten M600 (WM6 w/ MS BT stack) do not have this issue.
Is anyone with the Bluetooth problem running MS Voice Command? I'm still on R1A. I had no trouble at all using my Motorola T505 A2DP kit, but when I installed MSVC, the stupid thing would drop out as soon as I picked up a call. Uninstalling MSVC seems to have done the trick.
bedlam_au said:
Is anyone with the Bluetooth problem running MS Voice Command? I'm still on R1A. I had no trouble at all using my Motorola T505 A2DP kit, but when I installed MSVC, the stupid thing would drop out as soon as I picked up a call. Uninstalling MSVC seems to have done the trick.
Click to expand...
Click to collapse
Hi, yes I have Voice Command 1.6 on my device. It's working pretty well, but I know, what you're talking about -
Please try it with a usual BT headset (without the AD2P / AVRCP profiles!) if you have this possibility, - you'll see that it will work without any hassle.
I made this experience after I tried the HBH-660 and a Motorola headset.
Anyway - the new firmware R2A is recommended, even if the BT issue isn't solved.
But interesting to know that it seems to be a bug in HTC machines... so it will exist in further firmware updates... probably... I personally don't hope so....
No problems with the Sony HBH-IS800's and the bluetooth turning off randomly.
I have a problem with the WIFI randomly turning itself on during phone calls but no problems with anything turning off.
I have HBH-DS980 and I don't have any problems with disconnecting it on my X1 - not with R2A and not with R1A UK roms, also tested few modifided roms and there woudn't any problems too. I am also using SE MBW-150 watch and it also don't disconnect's with X1 (tested with R1A and R2A). I have BT turned on in my X1 all the time (previously in R1A rom and now in R2A) and after I turn on my HBH-DS980 headsets it will connect with them automaticly. Only sometimes I have to switch off and switch on againg BT to get connected with headsets but I think its headsets problem not the phone. But I never had a problem with suddenly disconnecting (not even once).
ell82 said:
I have HBH-DS980 and I don't have any problems with disconnecting it on my X1 - not with R2A and not with R1A UK roms, also tested few modifided roms and there woudn't any problems too. I am also using SE MBW-150 watch and it also don't disconnect's with X1 (tested with R1A and R2A). I have BT turned on in my X1 all the time (previously in R1A rom and now in R2A) and after I turn on my HBH-DS980 headsets it will connect with them automaticly. Only sometimes I have to switch off and switch on againg BT to get connected with headsets but I think its headsets problem not the phone. But I never had a problem with suddenly disconnecting (not even once).
Click to expand...
Click to collapse
Thank you very much ell82, but maybe I should describe more specifically - disconnections also happens after calls - for example, if you switch on your BT headset (in this case the DS-980), you see a symbol next to the BT symbol on the top of the phone, that indicates, that a BT headset is connected. Now, I figured out, that after calls this symbol dissapears and the BT headset dissconnects, so I have to push the button on the DS-980 again to get connected with the phone, you know? And when I get a call, the phone does not automatically transfer the call to the headset, I always have to push the button on it first, to be connected again...
And you also confirm that sometimes you have to switch the BT on and off again - this is absolutely the same with my phone.
You assume it is a problem with the specific headset DS-980 ? Maybe, but SE support told me that there is no firmware update or sth. similar for this type... what a pity -
Anyway I hope it is not a hardware bug of the phone - I haven't heard of any phone that was repaired or refurbished because of the Bluetooth bug.
Ok, so can we say that the HBH-DS980 will not work with X1 as it should do ?
This is very pity, because it is the top of thir line of headset products... and I liked it very much on my previous P1i and it worked perfectly on it...
Freako said:
Thank you very much ell82, but maybe I should describe more specifically - disconnections also happens after calls - for example, if you switch on your BT headset (in this case the DS-980), you see a symbol next to the BT symbol on the top of the phone, that indicates, that a BT headset is connected. Now, I figured out, that after calls this symbol dissapears and the BT headset dissconnects, so I have to push the button on the DS-980 again to get connected with the phone, you know? And when I get a call, the phone does not automatically transfer the call to the headset, I always have to push the button on it first, to be connected again...
And you also confirm that sometimes you have to switch the BT on and off again - this is absolutely the same with my phone.
You assume it is a problem with the specific headset DS-980 ? Maybe, but SE support told me that there is no firmware update or sth. similar for this type... what a pity -
Anyway I hope it is not a hardware bug of the phone - I haven't heard of any phone that was repaired or refurbished because of the Bluetooth bug.
Ok, so can we say that the HBH-DS980 will not work with X1 as it should do ?
This is very pity, because it is the top of thir line of headset products... and I liked it very much on my previous P1i and it worked perfectly on it...
Click to expand...
Click to collapse
This is exactly the same issue I am talking about and it's NOT specific to DS-980 alone. I tried DS-980, DS-205, DS-220, JVC BT-1, Clip-D Radio, and one Jabra model. And they all have the same issue on my X1 and Kaiser. (but not on my Asus P525 and Eten M600). The issue not happening 100% of the time but at least 80% which is enough to be frustrated.
jackleung said:
This is exactly the same issue I am talking about and it's NOT specific to DS-980 alone. I tried DS-980, DS-205, DS-220, JVC BT-1, Clip-D Radio, and one Jabra model. And they all have the same issue on my X1 and Kaiser. (but not on my Asus P525 and Eten M600). The issue not happening 100% of the time but at least 80% which is enough to be frustrated.
Click to expand...
Click to collapse
Yes, 80% of that time is ok, but the 20% lead to be very frustrated - ABSOLUTELY !!
In a time (2009) were bluetooth does exist several years and where all bugs should have been cleared over the years..., the truth shows that there still exist "minor/major?" bugs in current phones...
BT Headset problems
I can confirm that the problems with BT and HBH-DS970 are a fact - and it seems to drain the battery enormously. I have tested for a few days the PV 710 (Mono handsfree), no issue. Today with the 970 my battery was empty after 6 hours standby, and it was disconnected allthough the icon said "BT-Stereo-Headset connected! After switching it off, the icon remained. Strange, isn´t it?
I come from P1i and there was no such problem at all.
I experience the same problem. New NL firmware and a Volkswagen (Bury OEM) Bluetooth carkit. My Nokia 6500 and SE K850i work perfectly but terminating a call makes the BT connection disappear on a fairly regular base. If the other party terminates it usually stays connected
...very strange but anyway it seems that it is mainly affected with AD2P / AVRCP devices - I hope it is just a software/firmware bug that can be fixed easily and not caused by a hardware failure....
Sorry guys but again I have to say it doesnt effect on my X1 and DS-980, never and I'm using it a lot. Have you guys tried it on fresh phone, without any additional software?
ell82 said:
Sorry guys but again I have to say it doesnt effect on my X1 and DS-980, never and I'm using it a lot. Have you guys tried it on fresh phone, without any additional software?
Click to expand...
Click to collapse
The first thing after the purchase of the phone was to couple the device with the DS-980 headset and the bluetooth issue was really not expected and made me angry and at that time I didn't have any extra software on it...
When did you buy your headset ? I bought mine approx. 1 1/2 years ago...
Maybe the current items go better with the X1?? I don't know.
But we found out that this issue was also caused in other Windows Mobile devices like the Kaiser, TyTn etc.
The poll shows significantly that there are still some who have troubles with bluetooth, even after update-
AND now we can ask them if any of you have tried the headsets with clean and fresh install ? (Xperia X1 without any additional software, even without sbp panel, etc...! )
I am curious...
Freako

1.5/Cupcake HSP (Phone) Bluetooth Problem -- any suggestions?

So... I've been very hesitant to post this here.
I originally updated to the Haykuro sapphire port some two weeks ago; I have since then tried the "Dude" mod, and the JF ADP 1.5 mod as well.
They all have exactly this same problem: My Lubix LC1 stereo bluetooth headset no longer works properly with the G1. The phone //says// it is connected with both the A2DP (music) and the HSP (phone) protocols; and the A2DP connection works perfectly. But the HSP connection is essentially non-existent, despite the phone saying it is connected under "Bluetooth Settings".
When I try to call someone w/ the phone, the audio is routed to and from the phone itself. There is no way to route the call to the bluetooth headset at all. This problem has persisted through all three versions; I have flashed and re-flashed, etc.
I have gone through two LC1 bluetooth headsets (a mishap with a rather large, rather bored dog.) They both behave in exactly this same way.
The bluetooth is working w/ my wife's Jabra 855 headset. And it worked perfectly fine in the 1.1 and 1.0 firmwares.
So... what's the deal? I'm not enough of a "computer-person" to know how to hack this myself, but if there were a way to port the 1.1 firmware's bluetooth profile to the 1.5 software, that would be awesome.
Much as it's nice to listen to music through the G1, that's not useful at the expense of the headset.
Is my only choice, if I want the 1.5/cupcake firmware, to //REALLY// purchase a new bluetooth headset thanks to the reversion/breaking caused by the Cupcake update itself?
Please help!
each new major upgrade version also comes with a matching radio firmware.
you only upgraded the system image - leaving the device unsynced with the radio image. Its a known issue. once you will upgrade your radio image most of your problem will go away.
radio image for Cupcake 1.5 can be downloaded from official HTC website.
No, I updated the radio. It had no effect on this problem whatsoever. I've done a clean downgrade/upgrade with each of the various 1.5 mods.
This is a problem with the 1.5 software. Even w/ the 1.5's radio and the JF 1.42 mod the LC1 worked perfectly.
No Devices Found
I have the most recent firmware, baseband, etc, but when I search for devices, it never finds any Bluetooth Devices.
Silly question -- but have you been putting those devices into pairing mode?
I am having the same exact problem with my BlueAnt V1 bluetooth headset. With the latest 1.5 builds across the board with the exception of the UK version that released a week ago I cannot use my bluetooth headset at all. It goes through the pairing as normal and shows connected (I even get the jazzy blue outline in the dial screen) but no audio to the headset what so ever same with my Car kit. What changed in the latest builds to the bluetooth profile?
you are not alone, same problem here with German G1 and Cupcake. It does pair with my navigation system and/or Motorola HF800. My navigation system can access the phone, read phone book and dial - but I do have no sound. Incoming calls do ring on the navigation system/headset, but if I pick up the call there is no audio connection. Any idea what to do?
Actually I consider to root and flash e.g. JF firmware hoping that this will bring any change. On the other site I am afraid that this is just waste of time and risk. Strange thing is that there are obvioulsy not many people with same problem, though they do exist and report same problem in various forums.
I have the same exact problem as well. My car radio has bluetooth HSP and A2DP. The A2DP works perfectly but when I dial a call, the HSP doesn't work. However, when I receive a call, it works. Also, I discovered if I disconnect the A2DP profile in the bluetooth settings on the phone, HSP works correctly.
opposite problem- HSP good but A2DP no good
I have the opposite problem as testing567. Phone shows it is paired for voice and media and so does my car (2009 Mazda6). AFAIK when I select AUX on my stereo; it should automatically start the music player on the phone, but it doesn't. When I manually open Music and play a song; it does not output on the phone's speaker nor the car stereo. Weird thing is that when the song is playing; the progress bar shows it playing very fast like it is skipping every 2-3 seconds. As soon as I turn the car off and the bluetooth disconnects; the song automatically resumes playing through the phone's speaker at a normal speed. I do not have another bluetooth audio device to test this with, so I am not sure if it is the car or the phone. No problems with bluetooth phonecalls. My cupcake is the official OTA release and as far as I can tell the radio is up to date (Baseband Version 62.50S.20.17H_2.2219.26I).
Im having the same problems, my bluetooth is paired and when i get a call my bluetooth rings, if i press it once to answer it goes straight to the phone, but if i press it twice i get the audio on my bluetooth. It sucks that you have to press twice just to be able to use your bluetooth. (Try it. Pair your Bluetooth, call yourself with another phone, and answer it by pressing twice on your bluetooth answer button.)
I had the same issue exactly as you describe.
I downloaded the 1.5 Radio version off HTC's website and everything works again
HTH
Smiffy.
Lordsmiff said:
I had the same issue exactly as you describe.
I downloaded the 1.5 Radio version off HTC's website and everything works again
HTH
Smiffy.
Click to expand...
Click to collapse
what's your radio (baseband) version?
mine is Baseband Version 62.50S.20.17H_2.22.19.26I and it takes 5-10 minutes for my already-paired parrot evo 3k to connect when my car turns on.

Categories

Resources