I had my 8125 flash a bad rom and was stuck on splash screen.
fixed it with mtty1.42
connect in bootloader mode with usb
choose usb connection not com1, or com2
you will get a white screen press enter
then you see cmd>
type format will show you what you can format
you want to format the os part starts with a b cant remember exactly
once its formated flash a rom and you should be good to go if you have any questions just let me know.
The final part!
insanavaca said:
I had my 8125 flash a bad rom and was stuck on splash screen.
fixed it with mtty1.42
connect in bootloader mode with usb
choose usb connection not com1, or com2
you will get a white screen press enter
then you see cmd>
type format will show you what you can format
you want to format the os part starts with a b cant remember exactly
once its formated flash a rom and you should be good to go if you have any questions just let me know.
Click to expand...
Click to collapse
You've got the final part of my research...
NICE MEN!!! thanks a lot please post this in upgrade and windows mobile 6 forum please! thanks a lot... the time i did it it shows USB then it wont...
whe shows me USB i can enter task 28 55aa and TA DAAA!!! it works...
do you remember if i need to choose A or B???????
Related
Whats needed:
TyphoonNBFTools: http://w1.whatcounter.com/dlcount.p...yphoonNBFTools_0.3_SPL1010064_SPVServices.zip
Any Official Rom (I used I-Mate SP3 WWE).
A Typhoon running Windows Mobile 5.0.
Reverting Back:
Run TyphoonNBFTools and Open the SPL1010064.nbf. Right click on SPL in the bottom part of the screen and choose Emergency Flash. If this is the first time you have used the program you will get a prompt on your phone to run the runtimes. Choose yes. Click OK to flash the new bootloader to your phone. Next disable Activesync by turning off USB connections. Turn off your phone. While holding down the Camera button insert the USB cable, the phone should run the bootloader and you will be presented with the tri-color screen. It should say USB in the bottom corner. Now run Mtty and choose USB connection. Hit enter in the blank white space. You should now see Cmd>. Type "info 2" without the quotes. You should see some information about your phone. Next type "format BINFS" agains without the quotes. This one is case sensitive. You should see format complete or something along those lines. Now close Mtty and re-enable USB connections. Run the exe from the update you downloaded and follow the instructions. Your phone should now boot back up to WM2003.
For those stuck in bootloader mode you will need to run mtty and reflash the wm5.bin to the phone then follow the steps above.
Leiden said:
Whats needed:
TyphoonNBFTools: http://w1.whatcounter.com/dlcount.p...yphoonNBFTools_0.3_SPL1010064_SPVServices.zip
Any Official Rom (I used I-Mate SP3 WWE).
A Typhoon running Windows Mobile 5.0.
Reverting Back:
Run TyphoonNBFTools and Open the SPL1010064.nbf. Right click on SPL in the bottom part of the screen and choose Emergency Flash. If this is the first time you have used the program you will get a prompt on your phone to run the runtimes. Choose yes. Click OK to flash the new bootloader to your phone. Next disable Activesync by turning off USB connections. Turn off your phone. While holding down the Camera button insert the USB cable, the phone should run the bootloader and you will be presented with the tri-color screen. It should say USB in the bottom corner. Now run Mtty and choose USB connection. Hit enter in the blank white space. You should now see Cmd>. Type "info 2" without the quotes. You should see some information about your phone. Next type "format BINFS" agains without the quotes. This one is case sensitive. You should see format complete or something along those lines. Now close Mtty and re-enable USB connections. Run the exe from the update you downloaded and follow the instructions. Your phone should now boot back up to WM2003.
For those stuck in bootloader mode you will need to run mtty and reflash the wm5.bin to the phone then follow the steps above.
Click to expand...
Click to collapse
Man! Can't thank you enough for this. I took my phone to the service centre, willing to pay for the repair, and they could not do it. Every thing works fine now. Very good manual, clear instructions and correct info!
THANKS!
Hi
I Am Trying To Follow The Procedure Mentioned. But When I Right Click On Spl I Am Not Getting 'emergency Flash' Active.
Can U Please Assist Me Regarding This
You need TyphoonNBFTools.dll installed on your phone. Try running TyphoonNBFTools and selecting Tools->Immediate Flash Tools->Test Immediate Flash. It should automatically install the required stuff for you. Check you phone when you run the program. You should get a prompt to installed a program from unknown publisher. Make sure to choose yes.
Stuck in bootloader
Just trying to do this following my question here.
I though it was going well but I have a major problem now! I managed to do the emergency flash, but every time I boot I just get the tricolour bootloader screen (IPL 1.00, SPL 1.01.0064) and can't get any further. Any ideas please? I have tried using mtty to load wm5.bin but get the error "MTTYDownloadImageNot allow operation!"
I have also tried re-doing the "format BINFS" and doing the above again but still no joy.
Any ideas would be much appreciated!
maybe u need to make a "goldcard"
my feeler (o2 xphoneII) lives again after flash with goldcard.
I can't find a way to create one for Typhoon, can you point me in the right direction?
I try flash Amadeus = Qtek 8100 with UpdateTool from Qtek 8310.
Update process stopped at 74% , and UpdateProgramm closed.
Now my Qtek 8100 not Powered ON , and can't enter in boot mode (tricolor screen) with "Camera" button hold + USB cable conneting.
PC don't see any USB devices when I connected my Qtek 8100 to USB port.
I think I erased Boot loader in my Qtek 8100 (but not sure).
Is any method for repair ?
WBR !
er1cc said:
I try flash Amadeus = Qtek 8100 with UpdateTool from Qtek 8310.
Update process stopped at 74% , and UpdateProgramm closed.
Now my Qtek 8100 not Powered ON , and can't enter in boot mode (tricolor screen) with "Camera" button hold + USB cable conneting.
PC don't see any USB devices when I connected my Qtek 8100 to USB port.
I think I erased Boot loader in my Qtek 8100 (but not sure).
Is any method for repair ?
WBR !
Click to expand...
Click to collapse
UR Phone is fried!
this happens to almost 1 out of 20 users.....that while downgrading/upgrading to another bootloader, ur phone becomes dead....
DomConway said:
Just trying to do this following my question here.
I though it was going well but I have a major problem now! I managed to do the emergency flash, but every time I boot I just get the tricolour bootloader screen (IPL 1.00, SPL 1.01.0064) and can't get any further. Any ideas please? I have tried using mtty to load wm5.bin but get the error "MTTYDownloadImageNot allow operation!"
I have also tried re-doing the "format BINFS" and doing the above again but still no joy.
Any ideas would be much appreciated!
Click to expand...
Click to collapse
get the tricolour bootloader type in mtty info 2 the type format BINFS then upgrade using rom upgrade
DomConway said:
Just trying to do this following my question here.
I though it was going well but I have a major problem now! I managed to do the emergency flash, but every time I boot I just get the tricolour bootloader screen (IPL 1.00, SPL 1.01.0064) and can't get any further. Any ideas please? I have tried using mtty to load wm5.bin but get the error "MTTYDownloadImageNot allow operation!"
I have also tried re-doing the "format BINFS" and doing the above again but still no joy.
Any ideas would be much appreciated!
Click to expand...
Click to collapse
i also got that problem but i reinstalled the patched RUU again and my phone now boot but i have not been able to go back to the 2003 as i insalled WM5 but still cant format the BINFS
If already have patcher the bootloader with the guide to upgrade to wm 6.0 can I ignore to do it again? I mean flash bootloader again ?
Guys,
I ve just downloaded this http://rapidshare.com/files/21256078..._DUT_11500.rar romversion in the understanding that it was for the HTC 9000 PDA. There was a file called MaUpgradeUt_noID.exe which I let 'upgrade' my 9000. However, I think something very VERY big went wrong! A reset by pushing the 2 buttons and reset button on the back gives me the option 0 to reset but all I can see after that is a black screen which says USB at the top and at the bottom v1.00
What happened and is this the end of my PDA? Sync won t work anymore now since my PDA can t be detected by windows because I can t get in the PDA!!!
Is there something I can do??!!!
PLEASE HELP ME OUT!!!!
Edit/Delete Message
sounds like you're just in bootloader mode
I think you are in what's called bootloader mode. Read the wiki to check - the screen you are describing sounds normal to me you plug you device into the comp via usb (with sync over usb disabled in active sync) then install a new rom.
You really shouldn't have tried to flash your rom without reading some instructions first but I think that your device should be fine.
If you have already upgraded your rom just do a hard reset and select the option to reset.
Will this thread help?
http://forum.xda-developers.com/showthread.php?t=310056
I'm sorry, this is the thread I ment to link:
http://forum.xda-developers.com/showthread.php?t=310054
strangely enough I found out that I DID use a good version picked from this http://forum.xda-developers.com/showthread.php?t=298020 post. In this thread mwang gives a link to here http://buzzdev.net/index.php?option=com_phorum&Itemid=125&phorum_query=read,40,30486,30486#msg-30486 where I picked the dutch version. I than double clicked the MaUpgradeUt_noID.exe file and the software for upgrading started. When he was at 100% he said the the ROM update was completed and that I had to do a reset. So, I than pushed the three buttons (2x the - button and the reset button at the back of the 9000) but all I than see is the bootloader menu with USB and V1.00...........
Sorry for putting it in three sub forum, my fault, but the device is from my work so I don t want it to be screwed up!!!
sanderh said:
Sorry for putting it in three sub forum, my fault, but the device is from my work so I don t want it to be screwed up!!!
Click to expand...
Click to collapse
Rather late now, but if it's owned by your company for work, should you really be di**ing with it?
Solution to probl: Stuck in Bootloader
The one way of fixing your problems....you're officialy stuck in bootloader,
Here's the way to fix it:
1. Stop Activesync USB connection on your machine under connection settings.
2. Uni : Reboot Bootloader then Connect USB ( If your phone isn't in bootloader already..)
3. PC : Run mtty1.42.exe ( Download from XDA's ftp site or search the forums, I'm sure you'll find it.)
4. Choose USB in "Port" (Reconnect if can't find/reconglize USB and try remove sim and sd card)
5.1 Press Enter
5.2 USB> (This will show up)
6. Type: Set 14 0
7. Press Enter
8. Run your rom update again and it should flash this time.
did it start??
did it start?? ?
Hi. first post.
Have an o2 exec. Different brand same deice and none of the other methods worked but finally got it working. Using mtty1.42.exe it would not see usb connection and therefore could not go down that route.
I booted into the bootloader mode that says serial at the top and v1.00 at the bottom.
Connected to the pc and cant remember if i stopped wcescomm.exe or not but you can try both ways.
Then started Midget_1990_v1_0_PU10_WWE.exe rom and followed the instructions and voila.
Hope this helps someone.
"Using mtty1.42.exe it would not see usb connection"
You need to disable the usb connection of active sync under connection settings and then only mtty will pick up a usb connection..
I had a wizard and trying to fix it.
When switch on, blue cingular screen appears and show ipl spl gsm os numbers.. and halts on.... it stays like this...
i enter RGB screen it says ONLY `ipl 2.25 spl 2.25` ...
when i connect it to usb.. USB text appears but when I try to install `love ROM` RUU says, it is not connected check computer check usb cable.. so it is invisiable for computer but in device manager it s shown as winCE syc device when I connect..
do u think it is bricked.. Or theres some to do....
thanks
it wasnt dead...
thanks to this forum!!
m_carleone82 said:
I had a wizard and trying to fix it.
When switch on, blue cingular screen appears and show ipl spl gsm os numbers.. and halts on.... it stays like this...
i enter RGB screen it says ONLY `ipl 2.25 spl 2.25` ...
when i connect it to usb.. USB text appears but when I try to install `love ROM` RUU says, it is not connected check computer check usb cable.. so it is invisiable for computer but in device manager it s shown as winCE syc device when I connect..
do u think it is bricked.. Or theres some to do....
thanks
Click to expand...
Click to collapse
Hi,all,i have this problem........ipl 2.17 spl 2.17....please help.......
m_carleone82:
press Camera+reset to enter RUU mode, then flash with Cingluar original ROM.
starkwong said:
m_carleone82:
press Camera+reset to enter RUU mode, then flash with Cingluar original ROM.
Click to expand...
Click to collapse
Hi Starkwong.....i have the same problem .....can i reflash to original rom even my MDA is not recognized by my PC?.....thanks for your reply
ichiban said:
Hi Starkwong.....i have the same problem .....can i reflash to original rom even my MDA is not recognized by my PC?.....thanks for your reply
Click to expand...
Click to collapse
Yes ! if it gets into Bootloaders mode(tricolor screen) with ipl/spl display and when hooked up with pc via usb,a small usb appears at the bottom of the Bootloaders,it means it has connectivity with the pc,You can flash the official rom in the Bootloaders.
ahhh, hardreset. the pumpkin in my eye.
"m_carleone82:
press Camera+reset to enter RUU mode, then flash with Cingluar original ROM."
I´m right now on the RGB screen , and how can now put the original ROm????
please help me
thx
hugomalheiro said:
"m_carleone82:
press Camera+reset to enter RUU mode, then flash with Cingluar original ROM."
I´m right now on the RGB screen , and how can now put the original ROm????
please help me
thx
Click to expand...
Click to collapse
While in Bootloaders (RGB) screen,hook up the phone with pc via usb cable,watch small usb appear at the bottom of the Bootloaders,run the RUU in the Rom you downloaded,follow the instructions,it'll start to flash.let it finish and the phone will reboot.
need help!!
my cingular8125 stucked in splash screen. however, it can still goes into bootloader mode.
when it is turned on, it only shows these informations:
ipl 2.26
spl 2.26
gsm 2.xx.x
os??? (no information)
some rom problem occurs i guess..
when i tried to flash it with other rom. i go to bootloader mode. connect usb but it doesn't connect in activesync. so i get an error when i start ruu.exe.
is it possible to flash rom on my wizard without using activesync?
or using sd card?
is there a dumped rom so i can flash rom using sd card?
any solutions??
need any dumped rom for my wizard..
SOLVED MY OWN PROBLEM:
for those having the same problem here's how i solved mine..
some things may not necessarily needed..
but these steps worked for me:
first thing first:
download a mtty.exe, if you got a zip extract it somewhere..
get a working wizard, or if your wizard can still backup your image you can..
since in my splash screen os onformation doesn't show up anymore.. sd rom backup on my wizard stucked in bootloader mode didn't work out for me.
so i get another working wizard running in cracing's wm6.5 you can get os images on any cooked rom you want..
1.) kill task manager first on your phone. if your'e using activesync 4.5 go to connections and untick the checkbox for "allow usb connections"
2.) go to bootloader mode (turn off the phone/remove battery then hold camera while powering on)
3.) connect usb you'll see little indication on your lower left part of your screen "usb"
4.) run mtty.exe
5.) choose //wceusbsh001
6.) then type "r2sd all" then enter
7.) you'll see a loading bar on your in your bootloader screen so you can see its progress..
8.)turn off the phone. enter bootlader mode. will ask you if you want to copy images on your sd.
9.) hold voice dial button(upper right-side corner of your phone ) and writing will begin
10.) when its done poweroff and on normally and your wizard is back to business..
cheers!!!
hello,
i have flashed the Nand android from the following link
http://forum.xda-developers.com/showthread.php?t=893948
Now I want to go back original win rom........
Problem is I am unable to make the Active Sync though my USB through android phone is detesting and in boot loader screen USB is coming up when I connect to USB.
How to uninstall the HSPL. magldr and then the nand android.
Guys I really need help any help is appreciated.
vikramdeepsingh said:
Problem is I am unable to make the Active Sync though my USB through android phone is detesting and in boot loader screen USB is coming up when I connect to USB.
Click to expand...
Click to collapse
the instructions are stupid, even though they are correct. ''get an activesync connection'' doesn't mean 'connect to the activesync program'', it means connect to usb,,,, windows uses the activesync usb drivers even though the activesync program doesn't recognise a phone when it is in bootloader mode.
so long as it says USB in bootloader, you are good to go.
but dear as long as my phone is not recognized by this active syn I cannot flash original rom............I tried flashing rom from the SD card by changing name to LEOIMG.nbh but it also does not work for me(I have read this in XDA forum only)
is there any other way to flash the ROM
vikramdeepsingh said:
but dear as long as my phone is not recognized by this active syn I cannot flash original rom............I tried flashing rom from the SD card by changing name to LEOIMG.nbh but it also does not work for me(I have read this in XDA forum only)
is there any other way to flash the ROM
Click to expand...
Click to collapse
get into tricolor bootloder mode > plug in the usb to pc > in hd2 u should see USB instead of serial...once u see this > run ruu from PC in admin mode...should work
vikramdeepsingh said:
I tried flashing rom from the SD card by changing name to LEOIMG.nbh but it also does not work for me
Click to expand...
Click to collapse
Maybe this will help you:
Solution from Djet:
you have to format your microSD in FAT32, I did it with my stock microSD and it worked. VolumeDown button before starting makes the device boot in UpdateMode (3color screen then gray screen asking to press PowerButton to update from leoimg.nbh or volumeDown to cancel).
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=614195
pReXx said:
Maybe this will help you:
http://forum.xda-developers.com/showthread.php?t=614195
Click to expand...
Click to collapse
I am pretty much sure that my sdcard is fat 32 formatted..........I will try once more when I will reach home and will post it the outcome.
---------- Post added at 05:02 PM ---------- Previous post was at 04:48 PM ----------
vikramdeepsingh said:
I am pretty much sure that my sdcard is fat 32 formatted..........I will try once more when I will reach home and will post it the outcome.
Click to expand...
Click to collapse
I have tried...........now the problem is I am entering into the gray screen for 2-3 sec and then it again come back to tri color screen........is there any need to do something else.......please advise on this
I am making sure that I release the volume down button when I see the tri color screen.
I am seeing the 00068002 and loading sign on the gray screen.........after that tricolor screen.
Please give your valuable advise on this problem.
gdsbalaji said:
get into tricolor bootloder mode > plug in the usb to pc > in hd2 u should see USB instead of serial...once u see this > run ruu from PC in admin mode...should work[/QUOTE
guess what I did worked........previously not but this time yes.
Click to expand...
Click to collapse