Hello, last week i damaged the usb connector on my trinity now data pin is broke (pin in the middle of connector), connection over the usb cabel with pc is not supported now. Fortunately charging the battery is ok
Because I have on my trinity damage varranty void sticker too, can i try it send to service, or its a waste of time? keypad is not ok too, key down, right and start, sometimes not response, but I order new one from cnn.cn if the service will be unsuccessful, I replace it.
But the main question is, because I cant use USB to upgrade rom? (I need flash original WM5 rom, now I use WM6):
Can i flash over the miniSD card complet firmware? OS, extrom, radio rom? and SPL??? because now i have SPL-9.99.CP and I need SPL-1.07 from my original rom, how it flash and no brick the device over SDcard?
Or can you help me, where I can "buy" new void sticker, or if its possible, can I make it?
Sorry for my bad english
Last question: When service will be unsuccessfull, do you know, where can I buy the new ExtUSB connector? I know that its hard solder on mainboard
Related
Anyone can help? URGENT !!!
The usb connection is lost in my dopod838, even can not charge the device. Stupid.
I tried to replaced the radio rom via the usb, then there was no reponse for around 25 mins, then i reset the device. At the start-up screen, there is no radio version shown, and finally, i can no aysc the device to my desktop.
What I can do without USB connection and mini SD card ??
Give me a hand please.
Is your device now in bootloader mode as in do you see a number on the bottom of the screen? If you do, then it means you are in the bootloader model. All you need to do now is re-install your ROM and everything should be back to normal.
UD.
Have you tried a/c charger and usb cable?
If there is nothing either way (no orange light) then it may be a hardware fault.
Also try a hard reset again just in case...else it's a warranty job I reckon.
Joe
recovered.
Thanks for your kindly replies.
please can you give me a image for try i repair my prophet, because i have only the bootloader with the ac power adaptator, i need just ipl 2.XX for try TO RESTORE FROM MY SD CARD
if you have ntrw.exe it's easy to restore sdcard! it's not illegal just you help me
my prophet is G3 and now after a bad downgrad i have:
ipl 1.01 (Wizard)
spl 2.20.0000 (no change)
gsm 01.12.10 (OLD PROPHET)
OS 1.13.0.21 'OLD PROPHET)
hello , i have resolved one part of my problem, now i can connect my prophet (G3) on computer for try upgrade rom but it work slowly and my ipl (1.01 FROM WIZARD) are not changed, it is possible to change ipl ?
please answer me!
ipl changed !
hello , i am happy , i have changed my ipl, now i have ipl 2.09 and spl 2.20.000 , two hard days for my prophet(lazare now) it's difficul for me for explend to you with my bad English but it's possible , thank's for your's archives.
adrilau said:
hello , i am happy , i have changed my ipl, now i have ipl 2.09 and spl 2.20.000 , two hard days for my prophet(lazare now) it's difficul for me for explend to you with my bad English but it's possible , thank's for your's archives.
Click to expand...
Click to collapse
How you did that...please help me
hello , i have try this :
get the battery out.
cut your charger cable open
the inner cable, the one inside of the inner white one connects to pin 1 from the physical top.
the outer one of the charger cable connects to the fifth pin from the physical top
no you go into bootloader and connect the usb cable, flash over another rom and try if it works... GET OUT THE BATTERY BEFORE YOU CONNECT THE PINS mine got damaged because of that
is work , you can have bootloader and connect to your pc usb cable for install new rom
hello , i have try this :
get the battery out.
cut your charger cable open
the inner cable, the one inside of the inner white one connects to pin 1 from the physical top.
the outer one of the charger cable connects to the fifth pin from the physical top
no you go into bootloader and connect the usb cable, flash over another rom and try if it works... GET OUT THE BATTERY BEFORE YOU CONNECT THE PINS mine got damaged because of that
is work , you can have bootloader and connect to your pc usb cable for install new rom (complet rom with ipl /spl os)
i think there are good way for restore ipl......
http://forum.xda-developers.com/showthread.php?t=296114
theres no problem getting the data of the device but the problem is i've reflashed the T-mobile with qtec rom, now I want to send back for repair if she has a the wrong rom i'm stuck!!
is there anyother way via memcard / exe or other that I can wipe the rom or reload a rom without usb??
if comes down to it I can get her open and resolder but i will lose any repair cover.
any ideas please? feel very stupid.
pez
It's posible to upgrade Radio of an ipaq 614c using the microSD similar to ROM update?
The problem I have is my usb port on my 614c is broken.
Thanks
Just following up, wondering if someone can help.
I'm stuck with FW 0.77
Thanks
USB header broken?
I don't know if you still need it but i know that it is possible to replace the broken USB n=mini connector in a few cases, as long as the chassislines are not broken too.
I try it, replaced 2 times, but the welding point are so small that they disconnets when charge the baterie again
deleted..nvm
It appears that my HD2 is having some problems with its USB-Port since a connection will only be established if the USB-cable is held in a weird angle.
My Phone has been kept very carefully and is otherwise in great condition.
I think this may be a problem with the usb-port inside and it still has warranty here in germany.
The problem is that i used Magldr to install Android through clockwork mod, is there a way to get back to Windows Mobile without using a usb cable?
Since i hardly think i could send it in with Android installed.
Chances are it is the port on your phone....They seem pretty prone to this problem after a while.......Im assuming you've tried a different cable/usb port right??
Good news is that yes, you can get back to WM without USB pretty easily.
You need to download the correct stock rom for your device.
Hit up HTC.com and enter your serial number to be absolutely certain.
Download the ROM and extract the .nbh file.
Rename it to LEOIMG.nbh and place it on the root of your SD card.
Power on the phone whilst holding the vol. down button.
It should boot to bootloader and take you through the flashing process...
Using a stock ROM will remove HSPL and whatever else... ta da.... factory perfect
Does that work even tho i have magldr?
EDIT: I have an O2 phone, not the normal firmware but one that was provider-specific, does that work, too?
Yeah, it should do.
MAGLDR runs in the chain after the "classic" 3 colour bootloader....
Try turning on the phone and holding vol down. You should get to the good old fashioned bootloader. If so, SD flash will work.
Hope that helps.
Hey that was helpfull man,thanks for that!!!
Out of curiosity, have you looked to see if the usb needs to be cleaned from dirt and lint?
A friends phone had the same problem, and would only work if held at a weird angle. I used a pin to carefully dig in the usb hole and a lot of lint and even dirt had crammed in there to stop the cable working.
just wanted to add something to this thread, correct me if i am wrong.
yes you can revert to a stock SPL+ROM+Radio using flash-via-sd-card method. so a functioning USB port is not necessary.
BUT! a fully functioning USB port IS necessary for flashing HSPL (which is the first step to unleashing yourself on all the wonderful fun possible on the HD2)
so if your USB port is faulty and you're thinking about claiming warranty, then be absolutely sure about the decision to "go stock" before you revert to stock using the flash-via-sd-card method. in case the USB repairs fail, you will be stuck with the stock SPL on there. in case you have to hold on to an HD2 which you reverted to stock but couldn't get the USB repaired, that could be a bummer if you've gotten used to HSPL and its benefits!