It's posible to upgrade Radio of an ipaq 614c using the microSD similar to ROM update?
The problem I have is my usb port on my 614c is broken.
Thanks
Just following up, wondering if someone can help.
I'm stuck with FW 0.77
Thanks
USB header broken?
I don't know if you still need it but i know that it is possible to replace the broken USB n=mini connector in a few cases, as long as the chassislines are not broken too.
I try it, replaced 2 times, but the welding point are so small that they disconnets when charge the baterie again
deleted..nvm
Related
Sorry, newbie question, but before I have to use my MDA Vario 2 as a door stop, does anyone know if it is possible to get out of the Multi Coloured Screen ? our office had a power cut while I was updating from WM5 to WM6 and now it is stuck on the following screen:
HERM300
IPL-1.01
HERM300
SPL-1.40.Olipro
USB or Serial (Depending if I have the usb cable connected)
Obviously I cant connect to the phone as it is not booting and Active Sync is not connecting so I can upgrade.
Am I buggered like a cat ?
FALSH ALARM !! Phew, Many thanks to Digbyi as I was able to re-set and re-load the ROM !
Could anyone can help me to solve No GSM poblem. I think there are many other users have same problem.
After it faild during update rom, My HP6915 represent NO GSM during booting and the phone funcation also doesn't work. But in HP Asset you can see it, just no firmware, no version number. I try to flash english radio rom and french radio rom, but always stop at 1%. This matter appeared after I flashed orange rom(french version). I think it locked by Orange.
Does any one can help us?
did you try the update with no sim and no minsd?
EREZYAD said:
did you try the update with no sim and no minsd?
Click to expand...
Click to collapse
Yes, I update without sim card and minisd. Always stop at 1%
to be on the safe side i will go over general insraction
battery full
recomended xp os & activesync 4.5 (not beta)
minsd & sim out
ac addapter connected (ac power from orig transformer)
hart reset your device before the update
connect device directly to computer's usb plug
run the update
try radio only &/or the all update you can also try on a different pc
if all didn't work read this and see if you can find somthing that works on the 6900
http://www.htcwizardweb.net/node/170
good luck
EREZYAD said:
to be on the safe side i will go over general insraction
battery full
recomended xp os & activesync 4.5 (not beta)
minsd & sim out
ac addapter connected (ac power from orig transformer)
hart reset your device before the update
connect device directly to computer's usb plug
run the update
try radio only &/or the all update you can also try on a different pc
if all didn't work read this and see if you can find somthing that works on the 6900
http://www.htcwizardweb.net/node/170
good luck
Click to expand...
Click to collapse
Thank you for your reply!
I tried but still same, stop at 1% when I flash Radio WAN OS, stop at 2% when I flash Radio FS. I tried to unlock simlock and CID unlock, but it doesn't work on my 6965
called a few places looks like the radio chip is fried. sorry man...not looking good.
try update again with this method
I got almost same problem. I tried to update GSM rom but update fail and my ipaq stuck at hp invent logo. try following steps to see if it works for you
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider
I also meet such question.
actualy. I met the same problem "No GSM" after wrong update. I thing I tried everything, but I Didn't try to flash the device via mini-sd card. I don't know the right address for GSM area. Did anyone know?
caoxt said:
I also meet such question.
Click to expand...
Click to collapse
COME ON guys some one can help us , i have too the same problem please help with radio stack !!!!!!!!!
me too,, really nedd help here.. my only phone sable...
Hello, last week i damaged the usb connector on my trinity now data pin is broke (pin in the middle of connector), connection over the usb cabel with pc is not supported now. Fortunately charging the battery is ok
Because I have on my trinity damage varranty void sticker too, can i try it send to service, or its a waste of time? keypad is not ok too, key down, right and start, sometimes not response, but I order new one from cnn.cn if the service will be unsuccessful, I replace it.
But the main question is, because I cant use USB to upgrade rom? (I need flash original WM5 rom, now I use WM6):
Can i flash over the miniSD card complet firmware? OS, extrom, radio rom? and SPL??? because now i have SPL-9.99.CP and I need SPL-1.07 from my original rom, how it flash and no brick the device over SDcard?
Or can you help me, where I can "buy" new void sticker, or if its possible, can I make it?
Sorry for my bad english
Last question: When service will be unsuccessfull, do you know, where can I buy the new ExtUSB connector? I know that its hard solder on mainboard
Hello,
i have a HTC Elf 128/256 with rom ONYX 3.0 (after hard reset ).
The USB connector in built-in the phone is a kind of broken:
can charge the battery with the USB cable but can't synchronize.
The device is discovered with errors in windows task bar.
I tried to sync some more phones and they work.
Now i want to use the warranty but the phone has a cooked ROM.
Is there anyway to reset the phone to a warranty supported ROM?
I have tried to flash with the sdcard but had no results in the tricolor menu.
If someone has any suggestion, i really need it!
Thanks!!
piriri007 said:
Hello,
i have a HTC Elf 128/256 with rom ONYX 3.0 (after hard reset ).
The USB connector in built-in the phone is a kind of broken:
can charge the battery with the USB cable but can't synchronize.
The device is discovered with errors in windows task bar.
I tried to sync some more phones and they work.
Now i want to use the warranty but the phone has a cooked ROM.
Is there anyway to reset the phone to a warranty supported ROM?
I have tried to flash with the sdcard but had no results in the tricolor menu.
If someone has any suggestion, i really need it!
Thanks!!
Click to expand...
Click to collapse
What kind of SPL do you have on your Touch? What;s your device CID?
You should be able to flash a stock ROM (if one exists) from SD for sure.
Hello,
here is the info you asked for:
Device ID: ELF010050
CID : HTC__506
IPL: 2.20.0002
SPL: 2.26.0000pof
ROM version : 2.27.80.1
ExtROM version : Cooked by dsixda
Operator version: Onyx 3.0
AKU version : 1.2.6
Page Pool: 8 MB
RAM Size : 128 MB
ROM Size : 256 MB
Model No. : ELF0300
Part Number: 99HEH034-00
MCC+MNC: Not found
I can access the Storage Card from the file Explorer in the ELF, but can´t flash the ROM.
I am trying to flash with a cooked rom (ONYX 4.0). This process should only bedone with stock ROM's or it works with cooked rom's too?
Thanks!!
I already tried to flash the ELF from the SD Card with the stock ROM that suits my CID and SPL.
No results flashing from the card.
When the ELF boots in tricolor mode, how can i start the flashing process?
Any help would be appreciated!!
Thanks!
Hello piriri
on the ELF upgrading forum, look for the one that says restoring your Touch via the bootscreen.
once on bootscreen, make sure you have the original stock rom (check the HTC site for details). ELF for ELF, ELFIN for ELFIN. If you're using an ELF, get the 1.11x rom, flash it and you'll be back. 2.20x for elfin.
make sure you uncheck the part that makes your usb connect "advance network connectivity" on your settings. then your elf will be fine.
peace
Hello Samaral
First thank you for your answer, but i can´t synchronize the ELF to computer through USB, i have the USB connector broken in the phone!
I need to flash a ROM without using the USB cable!
I tried flashing from the SD Card but it's not starting thr flashing process...
Maybe i can have a help from someone??please??
Thank you!
piriri007 said:
Hello Samaral
First thank you for your answer, but i can´t synchronize the ELF to computer through USB, i have the USB connector broken in the phone!
I need to flash a ROM without using the USB cable!
I tried flashing from the SD Card but it's not starting thr flashing process...
Maybe i can have a help from someone??please??
Thank you!
Click to expand...
Click to collapse
Make sure your SD is formatted in FAT32 not FAT
I've got the same problem,is it possible to do a rom update via bleutooth?
Hello
I have this problem since i change my rom to Onix( i don't remember what version)
Bu if you try several times one time it gonna work and then put the other ROM ( I put Onyx 4.0) and know works great.
Sometimes you have to put the cable and wait 5 minutes to start the sync.
Try and then tell us if you succeed.
joao M
It might be this..
On some devices I've noticed that the metal strips within the connector (in the phone, top part of the connector usually) looses away from its original position, this actually results in the problem you mentioned. If its not broken you may be able to unbend it and restore it to the original position with a thin pin or something of that sort. This should make things work again.
To prevent this from keep happening just be carefull when you plug/unplug your cables into it. Be gentle when inserting the cable and make sure to put the pressure to insert it only when its in the exact position.
hope this helps... good luck
Try first
Hi Piriri
another simple check before all the rom flashing,
1-change the cable, worked for me more than once.
2-go to Settings>>>Connections (in some roms System)>>>>Usb to Pc>>>>uncheck "enable...etc".
I hope it helps
Hi, what´s the name of file by flash from sdcard? in polaris the name is POLAIMG.* and in elfin?
Install the latest activesync
My guess is that your pc is running windows xp.. and you have not installed the latest activesync on your system.. you can download the latest activesync installer(version4.5) from www.microsoft.com/en/us/downloads.aspx/.. install that and then reconnect your device.. if you are running windows vista.. try to update the usb drivers.. again you can download these drivers from microsoft.. you will have to search for the appropriate drivers and then install them..
If you want to send it back under warranty, mine went back to tmobile with a cooked rom. they didnt say anything but flashed it with the rom that looked like a stock nike rom!
when you enter in bootloader mode before the trecolor screen you can see a white screen flasing, well, at this white screen is where you can flash from the sd, if your phone dont stay there and ask you to press power buttom to flash its cause you havent a proper sd, i meant fat 32 formated sd with ONLY one file in it named elf0img.nbh, if you use it correctly it have to work por narices
Hi guys, i have installed the motion rom but i have one problem the cable of the charge it removes and it gets back(plug and unplugged) i have tried most cable but the problem is not fixed...i have an answer if i install a stock rom with odin the problem can be solved? Sorry for my english and thanks for all help me..
If you mean that your device cant be charged by anyway try reflashing the ROM i've had this problem too and a reflash fixed it
Axell. said:
If you mean that your device cant be charged by anyway try reflashing the ROM i've had this problem too and a reflash fixed it
Click to expand...
Click to collapse
I have tryed to reflashing the rom but the problem of the charge is not fixed...now i try to install the stock rom with odin. Thanks for you answer
No i can t install the stock rom because the usb on pc won t connect i am so tired how i can fix guys? Pls thanks for help me
AnimeCS said:
No i can t install the stock rom because the usb on pc won t connect i am so tired how i can fix guys? Pls thanks for all help me
Click to expand...
Click to collapse
Seams that the USB port on the phone is sustained a damage a one of the second pair of pins is either burned out or broken & first pair is not in a very good shape either. So the only real solution in your case is to get it to the repair service & get it fixed by replacing the USB port.
By the way this is something you learn to live with Samsung phones (all do it happens & on other brand's).
Zola III said:
Seams that the USB port on the phone is sustained a damage a one of the second pair of pins is either burned out or broken & first pair is not in a very good shape either. So the only real solution in your case is to get it to the repair service & get it fixed by replacing the USB port.
By the way this is something you learn to live with Samsung phones (all do it happens & on other brand's).
Click to expand...
Click to collapse
Ah okey thanks very much for you reply. Yes i go on repair service :good: