Pls help ti solve NO GSM problem! - Sable

Could anyone can help me to solve No GSM poblem. I think there are many other users have same problem.
After it faild during update rom, My HP6915 represent NO GSM during booting and the phone funcation also doesn't work. But in HP Asset you can see it, just no firmware, no version number. I try to flash english radio rom and french radio rom, but always stop at 1%. This matter appeared after I flashed orange rom(french version). I think it locked by Orange.
Does any one can help us?

did you try the update with no sim and no minsd?

EREZYAD said:
did you try the update with no sim and no minsd?
Click to expand...
Click to collapse
Yes, I update without sim card and minisd. Always stop at 1%

to be on the safe side i will go over general insraction
battery full
recomended xp os & activesync 4.5 (not beta)
minsd & sim out
ac addapter connected (ac power from orig transformer)
hart reset your device before the update
connect device directly to computer's usb plug
run the update
try radio only &/or the all update you can also try on a different pc
if all didn't work read this and see if you can find somthing that works on the 6900
http://www.htcwizardweb.net/node/170
good luck

EREZYAD said:
to be on the safe side i will go over general insraction
battery full
recomended xp os & activesync 4.5 (not beta)
minsd & sim out
ac addapter connected (ac power from orig transformer)
hart reset your device before the update
connect device directly to computer's usb plug
run the update
try radio only &/or the all update you can also try on a different pc
if all didn't work read this and see if you can find somthing that works on the 6900
http://www.htcwizardweb.net/node/170
good luck
Click to expand...
Click to collapse
Thank you for your reply!
I tried but still same, stop at 1% when I flash Radio WAN OS, stop at 2% when I flash Radio FS. I tried to unlock simlock and CID unlock, but it doesn't work on my 6965

called a few places looks like the radio chip is fried. sorry man...not looking good.

try update again with this method
I got almost same problem. I tried to update GSM rom but update fail and my ipaq stuck at hp invent logo. try following steps to see if it works for you
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider

I also meet such question.

actualy. I met the same problem "No GSM" after wrong update. I thing I tried everything, but I Didn't try to flash the device via mini-sd card. I don't know the right address for GSM area. Did anyone know?

caoxt said:
I also meet such question.
Click to expand...
Click to collapse
COME ON guys some one can help us , i have too the same problem please help with radio stack !!!!!!!!!

me too,, really nedd help here.. my only phone sable...

Related

Prophet upgraded with Wizard ROM by mistake

Just tried to upgrade my S200 with a 9100 ROM ver 2.8.7.1 WWE (by mistake of course) and I can't turn it on anymore. Somehow it didn't even warn about wrong ROM.
Tried to hardreset it but no luck. When I keep the camera button it goes to RGB only when connected to the charger.
When connected to PC, the red and blue leds keep flashing and my PC gives Error 260 when I try to revert back to the S200 RUU.
Does anyone know how to bring it back to life? Is there a way to boot it from SD card?
-
I-mate Jam
Qtek 9100
Qtek S200
Don't panic!
I did the same thing some time ago!
What you need to do is make sure that the battery is fully charged. (The flashing of the screen can be a result of the flat battery.) Unfortunately, it is not possible to charge the battery when the wrong ROM is installed, as the ROM obviously tells the Prophet how to charge.
Let's assume you have an okay battery.
1) Start the Prophet in Boot mode. This is done by pressing and holding the Camera button and then pressing the soft-reset button. Keep holding for about 7 seconds, and the coloured bands should appear.
2) Connect to PC using the UDB cable.
3) Run the correct ROM upgrade. You do not need to be paired with ActiveSync, as the update programs are intelligent.
4) If the update does not work (and it fails at 95%), then try again. If it still fails, try again and do a soft-reset mid-way through. This will kill the ROM upgrade and you should then be able to do it fine after that.
The really important thing is that the battery is charged before you do this. Unless anyone makes a USB cable that can charge AND connect to PC, then a fully charged battery is a must.
Let me know if this helped.
Check this Out
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!
Check this Out
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!
Re: Boot from SD?
zealerc said:
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!
Click to expand...
Click to collapse
I am a bit confused, does that mean that ALLOW USB CONNECTIONS has to be chacked or unchecked?
I did the same exact mistake. Now, my baterry is fully chaged (which I can check on another phone) but when I put it in S200 it shows that the battery has 0%. Conseqeuntly, when i unplug the power cord the phone dies. I have no way of running the new ROM on it. I tried running a bootable SD but it only installed part of the software. i read on this forum that such a thing happens and that one would need to run a full version ROM from a computer. So, how do I do it??? I am almost giving up all hope of ever making this phone work
Does anyone have a file to boot from SD and is it possible to run a full ROM from SD. Please help!

critical problem in jamin for help please

My friend's jamin when he tried upgrading with smart1 wm6
after the flashing process finished it gives the 3 colors of boot loader
the screen flickers continously with the 3 colors
no way to hard reset the device
and activesync doesn't feel it
I searched all the forum for a problem like this but I didn't find any
any suggestion please, or any help?
Flash NVID Rom and try Smart again. Read WM6 upgrade Manuel and readme for the ROM.
NetrunnerAT said:
Flash NVID Rom and try Smart again. Read WM6 upgrade Manuel and readme for the ROM.
Click to expand...
Click to collapse
Please how can i flash with the activesync doesn't notice my device and where's NVID Rom
Ok. I'll search for it but please help how can I flash it to the device which doesn't recognized or felt by PC
If your device is in bootloader mode, activesync cannot recognize it but this is normal. Jamin is recognize only as a usb device and you can downgrade it to NVID rom easly.
Then you could upgrade your favorite rom, I suggest PDAVIET 4.0.0.1
Bye for now
divxmaniak said:
If your device is in bootloader mode, activesync cannot recognize it but this is normal. Jamin is recognize only as a usb device and you can downgrade it to NVID rom easly.
Then you could upgrade your favorite rom, I suggest PDAVIET 4.0.0.1
Bye for now
Click to expand...
Click to collapse
I think I didn't discuss the problem well
The Problem is when I start to flashing a rom a message tells that check if the usb is connected and if the device is connected .
This is happen with the device is connected to the cable and the tricolor screen is flicking . and the device doesn't open doesn't flashing.
must use NVID rom. maybe qtek nvid one from here? http://wiki.xda-developers.com/index.php?pagename=Prophet_ROMs
hasanemara said:
I think I didn't discuss the problem well
The Problem is when I start to flashing a rom a message tells that check if the usb is connected and if the device is connected .
This is happen with the device is connected to the cable and the tricolor screen is flicking . and the device doesn't open doesn't flashing.
Click to expand...
Click to collapse
If the problem still there, Try to release the battery for 1-3 hours and put it again to the device, go to the boot loader and pray. Hopefully it could work. Actually, this way worked on my Himalaya and Prophet.
Just run the "Step 1" component of the PDAViet ROM (http://rapidshare.com/files/32728615/Prophet_PDAViet_Step1.zip), which is just a plain AKU 2.20 NVID. This will find your device even if its in bootloader mode (it doesnt depend on activesync). Just flash it with that sucker and you should have a working phone on WM5, then you can safely upgrade it to WM6 (or leave it if you like).
ekto said:
Just run the "Step 1" component of the PDAViet ROM (http://rapidshare.com/files/32728615/Prophet_PDAViet_Step1.zip), which is just a plain AKU 2.20 NVID. This will find your device even if its in bootloader mode (it doesnt depend on activesync). Just flash it with that sucker and you should have a working phone on WM5, then you can safely upgrade it to WM6 (or leave it if you like).
Click to expand...
Click to collapse
I shall try and tell you the result
error 260 this is the result
i have a slight variation problem like this...
1. i was upgrading my O2 Neo to the latest WM05 & the phone went to bootloader mode & the upgrade started searching for the phone as normal..then some error & it stopped upgrading while the phone was in bootloader mode..
2. at that time,i got an urgent call & had to leave the phone in bootloader mode...
3. when i came back..the phone was dead & now it wont startup at all.. not even in the bootloader mode.
4. Maybe the batteries dead...so i charged it (Over night)..nothing happened in the morning..
5. kept the battery removed for about 5-6hours & still nothing happens..it simply does not startup.
6.I've tried holding the camera button & resetting, but it wont go into bootloader mode.
7. i;ve tried holding the connections button + camera button _ reset but it wont hard reset...
can anyone help me here...
what can i do???
hasanemara said:
error 260 this is the result
Click to expand...
Click to collapse
Error 260... If i remember correctly that's "cant find device" or something.
Few things to check:
Is the PC you are upgrading on running windows vista?
If so, use a different PC running windows XP.
Have you tried a different USB cable?
If not, do so, this tends to be the cause of problems like this.
Have you checked device manager?
Go to control panel, Administrative tools, computer management, device manager and see if you can find your device. If it has a yellow ! icon on it or is listed as "Unknown device" or anything like that then you may need to reinstall the drivers (int hsi case the easiest way to do that is to reinstall activesync). If everyhting is working properly it should show up as "HTC USB Sync", "PocketPC USB Sync" or something like that under the heading "Mobile Devices".
Have you just plain tried another computer, regardless of the OS?
I found that I could never get my phone to flash on my laptop, but it worked without a problem on my desktop. This is not to say laptop's cant do it, it simply means some computers just have problems like (in my case i believe) no USB 2.0, or too low-powered USB ports.
ekto said:
Error 260... If i remember correctly that's "cant find device" or something.
Few things to check:
Is the PC you are upgrading on running windows vista?
If so, use a different PC running windows XP.
Have you tried a different USB cable?
If not, do so, this tends to be the cause of problems like this.
Have you checked device manager?
Go to control panel, Administrative tools, computer management, device manager and see if you can find your device. If it has a yellow ! icon on it or is listed as "Unknown device" or anything like that then you may need to reinstall the drivers (int hsi case the easiest way to do that is to reinstall activesync). If everyhting is working properly it should show up as "HTC USB Sync", "PocketPC USB Sync" or something like that under the heading "Mobile Devices".
Have you just plain tried another computer, regardless of the OS?
I found that I could never get my phone to flash on my laptop, but it worked without a problem on my desktop. This is not to say laptop's cant do it, it simply means some computers just have problems like (in my case i believe) no USB 2.0, or too low-powered USB ports.
Click to expand...
Click to collapse
No I didn't change any and I can connect my o2 xda mini to the same cable
I want to ask few technical question
HOW CAN A SOFTWARE DAMAGE THE DEVICE?
CAN A SOFTWARE FOR EXAMPLE BURNS A PROCESSOR OR SOMETHING LIKE THIS?
If So there will be a big problem with those types of devices
a virus for example can destroy my device's board or processor!!
Yesterday My friend went to an I-mate customer service who tel him that
the board had been destroyed by the bad software !!!!!!!!!
Please Give me technical advice about this problem
and is there a web site for him to buy this board (i-mate jamin)?
I've tried everything... even tried it on my desktop... but my phone just wont turn on now. i've kept the battery removed for more than 8hrs now... i've even charged it for more than 8hrs non-stop..nothing happens..
maybe i should get hold of a charged battery & try it with that battery...?
Any clue how to get my phone started??
got it working !!! PHEW... i used my HP battery which was charged & put it into it..now i've got my bootloader & i'm installing the new OS as we speak... 15% done.... keeping my fingers crossed
done.. got my HP Ipaq battery , which was charged & my new started up in bootloader more.. PHEW !!!
66% done... keeping my fingers crossed
ok, installed...now, one more problem..my touch screen's not working...???
Any idea what to do?
i installed "Prophet_PDAViet_Step1"

Bricked Hermes (SPV M3100) while flashing SPL - any help or sugestion are wellcomed

All started with trying to upgrade(rewrite) the GSM part because the Hermes had problems with phone part - when trying to call - the phone stop responding, bus the pda part sill worked.
So - I tried and tried and tried again, reading many threads about HARD SPL,Flashing radio, etc. Nothing worked..
In the end "i managed" to kill GSM - phone had "No Gsm" on boot-up.
From there i tried to downgrade SPL to 1.04 so that i try to "raw" rewrite the GSM part.
But something went terribly wrong, and while downgrading SPL, the phone suddently shutdown and never opened again.
Now i have the folowing situation: NO BOOTLOADER, no usb conectivity, nothing
This means that i cannot connect via USB whatever i try.
Is there any hope for me? or is it TOTALLY BRICKED?
Any help is apreciated!! I can even dismantle the mobile if there is any way to flash it via some kind of jtag connection...anything ...
The folks at www.imei-check.com can do the JTAG flashing. Just email them. It would be costly for you to do it yourself...
Are you saying that the phone won't turn on at all or that it does but you can't get a bootloader screen?
Have you tried taking the battery out for a while? Have you tried flashing an OEM rom and radio compatible with your device off an SD card?
All of this info is in the wiki, as are OEM roms you can flash.
Let us know how you get on.
Good luck.
WB
Try this:
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber
5.) Soft Reset
@wacky.banana: The phone is totaly dead: no bootloader, doesn't boot at all, doesn't seem to have any USB conectivity at all. Flashing from micro sd doesn't work : probably because the bootloader isn't working.
@drummer10630: i'll check with imei-chek about jtag flashing, especially the price and shiping costs.thanks
@markafreeman: I tried, but when i put the battery in, the red light goes off, not to amber . no soft or hard reset helps. not even leaving the battery out for 2 weeks - i had tried that too . thanks anyway.
Anything else I can try? - phone totaly dead, no bootloder, no usb conectivity - cannot use mtty, cannot flash from microsd
I had to get a replacement device at that point when it happened to me.
Maybe someone else know a way to get it working.
Good luck.
get onto orange
tell them you dropped the phone
and it crashed and wouldnt turn on
so you managed to hard reset it
and it crashed an ****ed up
they'll replace it
well they will send it to HTC
who just replace the handset rather than repair it
Hi dancameo2k , maybe you will not remember but plz:
I ve bought recenty an spv m3100, im effortless trying to flash the rom to an wm6 version.
Like you ive started with the hardsppl flash thing to prevent bricking it and prior to sd flashing... and im not sure if its workin...
plz can you explain in detail how did you bricked it??? thx!!!!
the rom you used to flash was an american version or european one???

Hp 6945 Stuck at Serial and Hp invent logo

Hello Everyone
I need big time help. I just bought Hp 6945 and I tried to update GSM rom from 1.02 to 1.08, while updating it says update fail and try to restart Ipaq and start again. Now My problem is Ipaq just stuck to Hp invent logo. I tried to reset and hard reset and remove battery but notthing work.
I need help
Could some please help me to How to fix this problem?
Thank you
same BS happened to me. the only way to fix it is to load the UK 6915 ROM. thats the ONLY way to fix it. AVOID this update do not try to update the radio. I bricked my phone doing this. STILL looking for a solution. Radio stack is daamged.
where Can I find Uk 6915 rom
Thank you for reply. Where can I found the UK 6915 rom. Is there any instruction to How to load rom?
Thank you
If is FIXEDDDDDDDDDD
Ok
I got it fixed, very simple solution
found it here
http://pdaphonehome.com/forums/hp-h...dowloaded-rom-update-ipaq-dead-need-help.html
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider
No network connection
Ok everything work fine, but Now I cann't connect to tmobile. It keep showing me no service.
Any Help please
Ok It is fixed again
There is another update at HP website, which is software update. After installing that everything working fine.
can anyone help? i just bricked my ipaq 6965 too. had already followed those few instructions without any success.. what do you mean by "with or without SIM card"?
After a soft reset, mine's stuck at the initial blue/white boot screen.
Hard reset doesn't work (assuming its call + hang up + power + poke reset).
Ideas?
bring back to life hw6945
i'we tried like you to upgrade radio part and a got an freezed phone
Solution for repair was flashing firmware with this program..
Download-Link #1: http://rapidshare.com/files/96527845/Ipaq_HW69XX_ENG_ROM.zip.html
download files from rapidshare posted by me ,r tested on my phone
hi i have tried to dl the rom asi having the same prob but the file cannot be downloaded. is there any other way to get from you
garyakw said:
hi i have tried to dl the rom asi having the same prob but the file cannot be downloaded. is there any other way to get from you
Click to expand...
Click to collapse
If you are stuck on a HP Invent Screen, with G.39, etc.
And you have tried to hard reset and softreset with no luck, this is what you do.
XP Instructions:
1. Download this link http://www.mediafire.com/?3ygfbx0sjdy
2. In the taskbar area in the right hand corner, right click on activesync, bare with me, I'm using Vista and have to remember this, click connections..., you need to uncheck everything click ok or apply...
3. press ctrl-alt-delete, end process wscescomm.exe, (named something like that, end the process.
4. Extract the file you downloaded if needed.
5. Connect your device to the usb port on your computer.
6. Run Uni Exit Bootloader Application. Done
Vista Instructions:
1. Download these 2 links, and extract them if necessary.
http://www.mediafire.com/?3ygfbx0sjdy
http://www.mediafire.com/?9pmjkponfsg
2. Start Device Manager, (Start-Control Panel, Class View[Far Left Corner])
3. Connect HW6900 to USB port, you should now see a Mobile Devices (Next to + sign), Double Click
4. Right-Click on the Device, Click Update Driver Software, Choose let me pick from a list, Uncheck compatible hardware box.
5. Click have disk, Browse to location where USBAS is extracted, choose the wceusbsh.inf file, Double Click.
6. You should see Microsoft USB Sync, if not and it reverts back to the already installed file, and the box rechecks itself, uncheck it, choose microsoft, and choose the latest Microsoft USB Sync to install
GOOD LUCK
in reference to
Default bring back to life hw6945
i'we tried like you to upgrade radio part and a got an freezed phone
Solution for repair was flashing firmware with this program..
Download-Link #1: http://rapidshare.com/files/96527845...G_ROM.zip.html
its a no go here...
i get error 402.... times out and no can do.... what was that about german language... maybe i just need it spelled out. which screen does the unit need to be in. there is two... monochrome serial vs usb and there is the hp logo blue and white screen frozen indefinitely... please help i love this phone...
Hi, the rapidshare file is missing!
Could you give working link or send me the file to mail, please?
ipaq dude said:
Ok
I got it fixed, very simple solution
found it here
http://pdaphonehome.com/forums/hp-h...dowloaded-rom-update-ipaq-dead-need-help.html
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider
Click to expand...
Click to collapse
Man,r u sure the above can work well???? Confusing......I did the above like u indicated,but it's not work on my device HP6915,could u make it in details how u fixed the problem of updating ur device,thanks!
Regards,
Brose
Thanks, This help get me out of freeze
Thanks for posting this link. It brought my hw 6945 back out of the freeze. Stay away from HP's site update. Bad news
johnnynomadic said:
in reference to
Default bring back to life hw6945
i'we tried like you to upgrade radio part and a got an freezed phone
Solution for repair was flashing firmware with this program..
Download-Link #1: http://rapidshare.com/files/96527845...G_ROM.zip.html
its a no go here...
Click to expand...
Click to collapse
Thanks for UNIEXITBOOTLOADER thing, it makes my 6965 rocks again! Btw, could this file be used on other pdaphone such as O2 Atom? Thx b4.
Maybe
Most Likely Yes
bmw2320 said:
Thanks for UNIEXITBOOTLOADER thing, it makes my 6965 rocks again! Btw, could this file be used on other pdaphone such as O2 Atom? Thx b4.
Click to expand...
Click to collapse
cdguider said:
Most Likely Yes
Click to expand...
Click to collapse
I don't think so,Curtis.....But as I know most of dopod device hardly be dead....

[Q] HD2 and ActiveSync.

Hi all.
I just a got a HD2 today. And the first thing that came in my mind was "Let's go to xdaDev to get a nice custom rom". I downloaded one.
After that I put the usb and try to make it syncronize. And the problem is here : ActiveSync dont reconize the phone. I spent the last 4 hours to google why it shall not work. I tried to unstick option at "Start=>Settings=> Usb to PC" but it dont work. Nothing more after perfoming a hard reset and reinstall ActivSync.
But something is strange : When I go in the bootloader, there is the 3 color screen and the phone Display "Serial" at the bottom of the screen ; and when I start it again with USB plugged, it doesnt display "USB" instead of "Serial" it's just void and if I remove the USB "Serial" is displayed.
Plz help me to make the phone syncronize .
I use Windows XP (no firewall, no antivirus) and an official Orange Rom. My SPL is 1.42.0000. I just hope there is no hardware problem ...
Some news ...
The HD2 isnt detected on 2 other PC (Both Win XP). I managed to syncronize my old Diamond too, and it worked well. Same with a HTC Touch and a Touch Cruise, the 3 ones works.
I also tried to use Bluetooth to get an Activesync connection and this time, it noticed the HD2 but no way to get a synchronization.
Any ideas ?
Try this: goto Settings, Other (Miscellaneous settings), USB to PC, Enable faster data data synchronization. Try to tick and untick the last setting.
It doesnt work . I'm trying to follow a "GoldCard" tutorial to flash to an official HTC rom. Maybe it's Orange operator rom ... But if you have any other suggestion, let me know
I can't believe that it's such a s*** to just connect the last HTC phone to a computer. The tutorial need ActiveSync to get the SD card ID so I will not succes in this way.
Is there another software that can be used instead of ActiveSync ?
Did you flash any rom at all or are you still stock?
If you have flashed already, Have you tried to go back to the default shipped rom using sd card (not goldcard)?
Find the rom that shipped with your device, extract the RUU_Signed.nbh file from it, copy it to your fat32 formatted sd card, rename leoimg.nbh, put card in phone, boot phone with down volume held, hopefully you get the message on the three colour screen saying something like 'press volume up to start' or somesuch.
THis should not only flash the rom, but also fix spl if it has become corruptted(which appart from hardware errors is the only reason i can see that it wouldn't recognise a USB connection)
Make sure it is the correct rom for your phone, though, correct vendor and region id.
I must say if you havent flashed yet it sounds like a hardware fault with teh usb cable/connector
I'm currently running a stock Rom from a french operator nammed "Orange". I haven't flashed anything since ActiveSync just dont want to know anything about my HD2.
Maybe I shall send it back to the seller. That's so frustating ...
If i dont find a way to solve this problem until the end of the day, I will return the phone.
Anyway thx for trying to help me
To me either the cable or the phone is faulty. Try another cable if you have one, if not just have the phone exchanged.
Phoque_You said:
I'm currently running a stock Rom from a french operator nammed "Orange". I haven't flashed anything since ActiveSync just dont want to know anything about my HD2.
Maybe I shall send it back to the seller. That's so frustating ...
If i dont find a way to solve this problem until the end of the day, I will return the phone.
Anyway thx for trying to help me
Click to expand...
Click to collapse
Ah in that case then i'd seriously consider taking it back /sending it back. Especially if you have tried more than one computer, sounds to me like faulty cable or USB socket.
kilrah said:
To me either the cable or the phone is faulty. Try another cable if you have one, if not just have the phone exchanged.
Click to expand...
Click to collapse
You must be right. I tried everything and I never had so much pain with my others HTC to get syncronization
I had the same problem not beeing able to connect to the internet via computer. After playing with the activesync settings on the Computer -> conection settings-> ticking on and off some of the boxes->ok, it worked again.
I have connected to three of these phones ( 2 french 1 english) and no problem whatsoever, everything happens without needing to touch any of the settings...is your pc even recognising that something is being plugged in on the USB?
Have you installed the latest version of activesync?
If you have done all the obvious things and it still does not work, the phone or the cable is defective...It should connect straight out of the box with a standard, un changed version of activesync.
Send it back!

Categories

Resources