please can you give me a image for try i repair my prophet, because i have only the bootloader with the ac power adaptator, i need just ipl 2.XX for try TO RESTORE FROM MY SD CARD
if you have ntrw.exe it's easy to restore sdcard! it's not illegal just you help me
my prophet is G3 and now after a bad downgrad i have:
ipl 1.01 (Wizard)
spl 2.20.0000 (no change)
gsm 01.12.10 (OLD PROPHET)
OS 1.13.0.21 'OLD PROPHET)
hello , i have resolved one part of my problem, now i can connect my prophet (G3) on computer for try upgrade rom but it work slowly and my ipl (1.01 FROM WIZARD) are not changed, it is possible to change ipl ?
please answer me!
ipl changed !
hello , i am happy , i have changed my ipl, now i have ipl 2.09 and spl 2.20.000 , two hard days for my prophet(lazare now) it's difficul for me for explend to you with my bad English but it's possible , thank's for your's archives.
adrilau said:
hello , i am happy , i have changed my ipl, now i have ipl 2.09 and spl 2.20.000 , two hard days for my prophet(lazare now) it's difficul for me for explend to you with my bad English but it's possible , thank's for your's archives.
Click to expand...
Click to collapse
How you did that...please help me
hello , i have try this :
get the battery out.
cut your charger cable open
the inner cable, the one inside of the inner white one connects to pin 1 from the physical top.
the outer one of the charger cable connects to the fifth pin from the physical top
no you go into bootloader and connect the usb cable, flash over another rom and try if it works... GET OUT THE BATTERY BEFORE YOU CONNECT THE PINS mine got damaged because of that
is work , you can have bootloader and connect to your pc usb cable for install new rom
hello , i have try this :
get the battery out.
cut your charger cable open
the inner cable, the one inside of the inner white one connects to pin 1 from the physical top.
the outer one of the charger cable connects to the fifth pin from the physical top
no you go into bootloader and connect the usb cable, flash over another rom and try if it works... GET OUT THE BATTERY BEFORE YOU CONNECT THE PINS mine got damaged because of that
is work , you can have bootloader and connect to your pc usb cable for install new rom (complet rom with ipl /spl os)
i think there are good way for restore ipl......
http://forum.xda-developers.com/showthread.php?t=296114
Related
I have a new Prophet (JAMin) and it does not start, even when charged. All that happens is the lights at the top flash, the screen blinks and then no more.
Any ideas, as I need the device later!!!
Does it show any serial number on the bottom of the screen or does it just show a blank screen.
What you could do is remove the battery, SD card out and leave the device like that for about an hour or so. After an hour just insert the battery (not the SD card) and then try charging again. Let it charge for about half n hour and then try switching on the device. Most likely, your device will now wake up, if it doesn't then you will probably need to wait till the amber light turns green indicating a full charge. Try switching on the device again, if still no luck, then you will need to take it down to a service centre.
It works when using power adapter, but not on usb
The prophet does start up when using the power adapter, but not when on the USB. Have left it 'charging', but the charge light is not on.
USB only provides a trickle charge and hence is not the best solution for "waking up" a device. Always make sure that you charge your device through the provided AC adapter. Only in cases of emergency or when synchronisation allow USB charging.
No charge light
No charge light is on. Is that right?
If there is no charge light, that means its not charging to begin with. Can you check if the USB port you are charging from is functional by attaching another device to it. Incase the USB port is fine, try charging from a different USB port; if it still behaves the same way, i suggest you take it down to a service centre. Its quite possible that the charging port on the Prophet is damaged.
sam_sykes said:
I have a new Prophet (JAMin) and it does not start, even when charged. All that happens is the lights at the top flash, the screen blinks and then no more.
Any ideas, as I need the device later!!!
Click to expand...
Click to collapse
Mine used to be like that after I installed spb plus previous version, it wont start at all...I had to switch to a new machine (for free) coz it was only day-2 after i bought the device (nice service btw).
Cheers!
I Have an SPV M600 which when switched on the screen blinks and then powers off, no charging light will only power up with the charger plugged in not with the usb data cable, i used a file called hard_SPL-G4 since then this error occured i think its the software program loader.
I cant reflash via active sync because the device powers off without the AC charger. i do have SD cards, but im unsure how to flash from SD i want my original spl version back and a better OS.
IPL 2.21.0001
SPL 2.21.01ip
GSM 02.69.21
OS 7.7.7.7
I can get to the tricolour screen bootloader with charger plugged please help any advice?
these are the original settings i think
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Once it is in bootloader, can you switch it to the USB cable?
Q: Once it is in bootloader, can you switch it to the USB cable?
A: no it switches the power off when i unplug AC but i can get to the windows OS if i power on with AC..? but flash via activesync no AC on reset.
I do have two SPV M600s im not touching the working one. but would like to fix the other one. SD Flash would help possible corrupt OS or SPL i think?
i can gain access to bootloader but i dont know how to initialize the NBH rom,
i could start the extrom cabs which had an autorun with a list of execution
i updated the rom Mysterious_1.0 all went ok i think
then i ran hard_SPL-G4 i had a lot of errors about sleep4.exe not win32 i think.
i am running x64 pro and upon reset all i had was an occasional screen blink and weak flashing orange and blue led.
ive tried different battery and a different USB to miniUSB. the active sync does take long time looking for changes on OS.
from usb i hold camera button and click reset switch it goes to USB bootloader for a second then off
if theres anyone out there who knows how to reflash the SPL version and a new OS for an SPV M600 english lang from an SD card please link files and explain the process in as much detail please? thankyou!
i did also update the radio version GSM could that be a cause!
The radio version should have nothing to do with it...
I am fairly sure there is something on the wiki about flashing from a storage card, but you need to make the dump of the ROM from the working device, so not much help there...
If you can get into bootloader whilst it is plugged into your computer, it's a very easy problem to fix...
I have decided to find the pinouts for a 4.5V charger (it should be 5V but im not destroying original) and a spare USB-miniUSB attach the power terminals from the charger replacing the miniUSB charge terminals, which should allow me to go to bootloader with USB present. i will post my results in here soon
about accessing bootloader
Hi i have just executed the jump spl files on my problem device and its taken me to a white screen with usb data cable, which i heard is the bootloader really and used tera term pro to dump rom etc. its seems to of hanged at the minute does it take a while to write?
im guessing i could go into the white screen mode and reflash an original orange rom?
New Original OS installed
Hi ive successfully installed a new OS so i presume the white screen is a bootloader. still my problem of powering off upon boot exists, so using this method i want to change the details below
OLD SETTINGS
IPL 2.21.0001
SPL 2.21.01ip
GSM 02.69.21
OS 7.7.7.7
NEW SETTINGS
IPL 2.10.0001 check
SPL 2.21.01ip SPL 2.10.0001 wanted
GSM 02.69.21 GSM 02.07.20 wanted
OS 2.10.1.22 check
Can i reinstall the wanted SPL/GSM from the white screen loader? does anyone know where i can get the files. SPV M600
Repaired 100%
I did it, its fixed charges now from USB data cable. and can enter tricolour bootloader. the problem was something wrong with the spl flash process ive redone that no errors excellent. im happy now
Will a ROM flash now?
Hi,
I tried a new rom and now am stuck at the bootloader with no OS on the phone.
ipl 2.10.0001
spl 2.10.0001
gsm 02.69.21
os 4.0.0.0
I have searched all the forums and still cannot get my spvm600 to do anything. I have tried to run several roms but the problem is they cant see the phone as activesync wont connect. is there a way i can boot from the sdcard or somthing or do i have a expensive paperweight. when i try to hold down the camera and comms keys on start it asks me to format the device and then says doen and goes back to the above screen
anyone?
ideas?
Try to restart your device and deliberatly go to boot loader (keep camera button in) (keep usb disconnected).
once at boot loader screen connect usb cable ... you should now see "usb" in bottom left corner on device screen.
now run a wm5 rom like in step 1 of "how to upgrade from WM5 to WM6" thread - - http://forum.xda-developers.com/showthread.php?t=310452.
it worked for me!
every rom i try to install on it needs activesync to connect to it but activesync douesnt connect to it as the phone has been formatted. there must be a way to fix it but but i am totally stuck
Rom Upgrade doesnt need Active Sync, you just need to be in bootloader and have the usb cable connected. Then just go through the update utility.
I try that and it still seems to say no device connected would you like to try copying again. I cant understand it cause it makes that bling noise when i plug it in
Use Update_NOID
You must use the No_ID Updater to upload a ROM from the 3 colour screen. Just run this exe file and you should not have any problems.
Hi,
Please help, I too have the same problem. Installed all the versions but no use. Can any one help me how to downgrade to Original German ROM version for Neo. So that I can return to O2 company... otherwise this become expensive paper weight
thankyouthankyouthankyou
YEEAAAAHHH
my phone is now working.
the no id rom worked a treat.
xtrafletch thanks a million!!
Sorry, newbie question, but before I have to use my MDA Vario 2 as a door stop, does anyone know if it is possible to get out of the Multi Coloured Screen ? our office had a power cut while I was updating from WM5 to WM6 and now it is stuck on the following screen:
HERM300
IPL-1.01
HERM300
SPL-1.40.Olipro
USB or Serial (Depending if I have the usb cable connected)
Obviously I cant connect to the phone as it is not booting and Active Sync is not connecting so I can upgrade.
Am I buggered like a cat ?
FALSH ALARM !! Phew, Many thanks to Digbyi as I was able to re-set and re-load the ROM !
Hello,
i have a HTC Elf 128/256 with rom ONYX 3.0 (after hard reset ).
The USB connector in built-in the phone is a kind of broken:
can charge the battery with the USB cable but can't synchronize.
The device is discovered with errors in windows task bar.
I tried to sync some more phones and they work.
Now i want to use the warranty but the phone has a cooked ROM.
Is there anyway to reset the phone to a warranty supported ROM?
I have tried to flash with the sdcard but had no results in the tricolor menu.
If someone has any suggestion, i really need it!
Thanks!!
piriri007 said:
Hello,
i have a HTC Elf 128/256 with rom ONYX 3.0 (after hard reset ).
The USB connector in built-in the phone is a kind of broken:
can charge the battery with the USB cable but can't synchronize.
The device is discovered with errors in windows task bar.
I tried to sync some more phones and they work.
Now i want to use the warranty but the phone has a cooked ROM.
Is there anyway to reset the phone to a warranty supported ROM?
I have tried to flash with the sdcard but had no results in the tricolor menu.
If someone has any suggestion, i really need it!
Thanks!!
Click to expand...
Click to collapse
What kind of SPL do you have on your Touch? What;s your device CID?
You should be able to flash a stock ROM (if one exists) from SD for sure.
Hello,
here is the info you asked for:
Device ID: ELF010050
CID : HTC__506
IPL: 2.20.0002
SPL: 2.26.0000pof
ROM version : 2.27.80.1
ExtROM version : Cooked by dsixda
Operator version: Onyx 3.0
AKU version : 1.2.6
Page Pool: 8 MB
RAM Size : 128 MB
ROM Size : 256 MB
Model No. : ELF0300
Part Number: 99HEH034-00
MCC+MNC: Not found
I can access the Storage Card from the file Explorer in the ELF, but can´t flash the ROM.
I am trying to flash with a cooked rom (ONYX 4.0). This process should only bedone with stock ROM's or it works with cooked rom's too?
Thanks!!
I already tried to flash the ELF from the SD Card with the stock ROM that suits my CID and SPL.
No results flashing from the card.
When the ELF boots in tricolor mode, how can i start the flashing process?
Any help would be appreciated!!
Thanks!
Hello piriri
on the ELF upgrading forum, look for the one that says restoring your Touch via the bootscreen.
once on bootscreen, make sure you have the original stock rom (check the HTC site for details). ELF for ELF, ELFIN for ELFIN. If you're using an ELF, get the 1.11x rom, flash it and you'll be back. 2.20x for elfin.
make sure you uncheck the part that makes your usb connect "advance network connectivity" on your settings. then your elf will be fine.
peace
Hello Samaral
First thank you for your answer, but i can´t synchronize the ELF to computer through USB, i have the USB connector broken in the phone!
I need to flash a ROM without using the USB cable!
I tried flashing from the SD Card but it's not starting thr flashing process...
Maybe i can have a help from someone??please??
Thank you!
piriri007 said:
Hello Samaral
First thank you for your answer, but i can´t synchronize the ELF to computer through USB, i have the USB connector broken in the phone!
I need to flash a ROM without using the USB cable!
I tried flashing from the SD Card but it's not starting thr flashing process...
Maybe i can have a help from someone??please??
Thank you!
Click to expand...
Click to collapse
Make sure your SD is formatted in FAT32 not FAT
I've got the same problem,is it possible to do a rom update via bleutooth?
Hello
I have this problem since i change my rom to Onix( i don't remember what version)
Bu if you try several times one time it gonna work and then put the other ROM ( I put Onyx 4.0) and know works great.
Sometimes you have to put the cable and wait 5 minutes to start the sync.
Try and then tell us if you succeed.
joao M
It might be this..
On some devices I've noticed that the metal strips within the connector (in the phone, top part of the connector usually) looses away from its original position, this actually results in the problem you mentioned. If its not broken you may be able to unbend it and restore it to the original position with a thin pin or something of that sort. This should make things work again.
To prevent this from keep happening just be carefull when you plug/unplug your cables into it. Be gentle when inserting the cable and make sure to put the pressure to insert it only when its in the exact position.
hope this helps... good luck
Try first
Hi Piriri
another simple check before all the rom flashing,
1-change the cable, worked for me more than once.
2-go to Settings>>>Connections (in some roms System)>>>>Usb to Pc>>>>uncheck "enable...etc".
I hope it helps
Hi, what´s the name of file by flash from sdcard? in polaris the name is POLAIMG.* and in elfin?
Install the latest activesync
My guess is that your pc is running windows xp.. and you have not installed the latest activesync on your system.. you can download the latest activesync installer(version4.5) from www.microsoft.com/en/us/downloads.aspx/.. install that and then reconnect your device.. if you are running windows vista.. try to update the usb drivers.. again you can download these drivers from microsoft.. you will have to search for the appropriate drivers and then install them..
If you want to send it back under warranty, mine went back to tmobile with a cooked rom. they didnt say anything but flashed it with the rom that looked like a stock nike rom!
when you enter in bootloader mode before the trecolor screen you can see a white screen flasing, well, at this white screen is where you can flash from the sd, if your phone dont stay there and ask you to press power buttom to flash its cause you havent a proper sd, i meant fat 32 formated sd with ONLY one file in it named elf0img.nbh, if you use it correctly it have to work por narices
I BRICK MY HTC WIZARD... CAN SOME ONE HELP ME PLEASE???? I OWN A HTC WIZARD FROM CINGULAR 8125 POCKET PC. RECENLY I TRYED TO FLASH MY POCKET PC BUT SOMETHONG HAPPEND.... IT JUST STAYS ON THE CINGULAR LOGO..
IPL 2.21.0001
SPL 2.21.O1ip
GSM 02.25.11
OS 2.18.0.0
AND IT JUST STAYS THERE.....
PLEASE HELP......
brick...
chipis said:
I BRICK MY HTC WIZARD... CAN SOME ONE HELP ME PLEASE???? I OWN A HTC WIZARD FROM CINGULAR 8125 POCKET PC. RECENLY I TRYED TO FLASH MY POCKET PC BUT SOMETHONG HAPPEND.... IT JUST STAYS ON THE CINGULAR LOGO..
IPL 2.21.0001
SPL 2.21.O1ip
GSM 02.25.11
OS 2.18.0.0
AND IT JUST STAYS THERE.....
PLEASE HELP......
Click to expand...
Click to collapse
I try to answer... (sorry for my bad english)
1. Make sure your battery up to 50%, 100% is recommended...
2. turn off u'r PPC
3. press camera,talk, and power button at the same time for a second until your display show 3 colour....
4. plug your cable data from PPC to desktopPC, and make sure your display show "USB", and try to re-flash with other ROMS.....
Good Luck
Thank for answer me and understand what i ment
Ok what software you recoment?. I do not know if i have a unlocked phone but i do know that i used it with t-moble even that my pocket pc is for cingular, i went to those stores that unlocked phones and that it
Help.
I have a Wizard G4 and I tried to install a WM6.5 ROM (TechTeamup Mega Wizard rom) from the default WM5. I did not put in the hard-spl (as I now read) before I tried to flash. Now when it boots, I go strait to the flash screen (tri-color) screen. I tried ot run the hard-spl-G4 and it says it cannot find a device. I have tried to re-flash back to WM5 ROMs that I have found, however it says it cannont complete "ERROR 296: UPGRADE ONLY, which makes me belive I need a G4 Wizard ROM that is a full (not upgrade). What steps should I take now to revert back to a WM5 so I can re-try the "unlock" hard-spl proceedure to make the phone WM6 compatible?
Anyone have any suggestions?
IPL 2.28.0001
SPL 2.28.0001
Download the original ship ROM for your phone.
Turn the phone off.
Press and hold the Camera key, now insert the USB cable, Keep holding the camera key until you get the boot loader screen.
Now run the ROM update to flash back to WM5.
ricozy said:
I try to answer... (sorry for my bad english)
1. Make sure your battery up to 50%, 100% is recommended...
2. turn off u'r PPC
3. press camera,talk, and power button at the same time for a second until your display show 3 colour....
4. plug your cable data from PPC to desktopPC, and make sure your display show "USB", and try to re-flash with other ROMS.....
Good Luck
Click to expand...
Click to collapse
I brick my wizard too... What happened was I flashed my own cook of m6r5 it say successful but on reboot, it shows htc logo then stays ay tricolor screen:
IPL 2.26
SPL 2.26
Bootloader wont work..tried many times but I cannot connect to PC...
Tried ricozy post above, can access 3 color... but still cannot connect to PC...
Please help...anyone..
IF u can enter bootloader...connect to pc...u shud c "USB" written in the left bottom corner ...then flash a rom as usual