I have a new Prophet (JAMin) and it does not start, even when charged. All that happens is the lights at the top flash, the screen blinks and then no more.
Any ideas, as I need the device later!!!
Does it show any serial number on the bottom of the screen or does it just show a blank screen.
What you could do is remove the battery, SD card out and leave the device like that for about an hour or so. After an hour just insert the battery (not the SD card) and then try charging again. Let it charge for about half n hour and then try switching on the device. Most likely, your device will now wake up, if it doesn't then you will probably need to wait till the amber light turns green indicating a full charge. Try switching on the device again, if still no luck, then you will need to take it down to a service centre.
It works when using power adapter, but not on usb
The prophet does start up when using the power adapter, but not when on the USB. Have left it 'charging', but the charge light is not on.
USB only provides a trickle charge and hence is not the best solution for "waking up" a device. Always make sure that you charge your device through the provided AC adapter. Only in cases of emergency or when synchronisation allow USB charging.
No charge light
No charge light is on. Is that right?
If there is no charge light, that means its not charging to begin with. Can you check if the USB port you are charging from is functional by attaching another device to it. Incase the USB port is fine, try charging from a different USB port; if it still behaves the same way, i suggest you take it down to a service centre. Its quite possible that the charging port on the Prophet is damaged.
sam_sykes said:
I have a new Prophet (JAMin) and it does not start, even when charged. All that happens is the lights at the top flash, the screen blinks and then no more.
Any ideas, as I need the device later!!!
Click to expand...
Click to collapse
Mine used to be like that after I installed spb plus previous version, it wont start at all...I had to switch to a new machine (for free) coz it was only day-2 after i bought the device (nice service btw).
Cheers!
I Have an SPV M600 which when switched on the screen blinks and then powers off, no charging light will only power up with the charger plugged in not with the usb data cable, i used a file called hard_SPL-G4 since then this error occured i think its the software program loader.
I cant reflash via active sync because the device powers off without the AC charger. i do have SD cards, but im unsure how to flash from SD i want my original spl version back and a better OS.
IPL 2.21.0001
SPL 2.21.01ip
GSM 02.69.21
OS 7.7.7.7
I can get to the tricolour screen bootloader with charger plugged please help any advice?
these are the original settings i think
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Once it is in bootloader, can you switch it to the USB cable?
Q: Once it is in bootloader, can you switch it to the USB cable?
A: no it switches the power off when i unplug AC but i can get to the windows OS if i power on with AC..? but flash via activesync no AC on reset.
I do have two SPV M600s im not touching the working one. but would like to fix the other one. SD Flash would help possible corrupt OS or SPL i think?
i can gain access to bootloader but i dont know how to initialize the NBH rom,
i could start the extrom cabs which had an autorun with a list of execution
i updated the rom Mysterious_1.0 all went ok i think
then i ran hard_SPL-G4 i had a lot of errors about sleep4.exe not win32 i think.
i am running x64 pro and upon reset all i had was an occasional screen blink and weak flashing orange and blue led.
ive tried different battery and a different USB to miniUSB. the active sync does take long time looking for changes on OS.
from usb i hold camera button and click reset switch it goes to USB bootloader for a second then off
if theres anyone out there who knows how to reflash the SPL version and a new OS for an SPV M600 english lang from an SD card please link files and explain the process in as much detail please? thankyou!
i did also update the radio version GSM could that be a cause!
The radio version should have nothing to do with it...
I am fairly sure there is something on the wiki about flashing from a storage card, but you need to make the dump of the ROM from the working device, so not much help there...
If you can get into bootloader whilst it is plugged into your computer, it's a very easy problem to fix...
I have decided to find the pinouts for a 4.5V charger (it should be 5V but im not destroying original) and a spare USB-miniUSB attach the power terminals from the charger replacing the miniUSB charge terminals, which should allow me to go to bootloader with USB present. i will post my results in here soon
about accessing bootloader
Hi i have just executed the jump spl files on my problem device and its taken me to a white screen with usb data cable, which i heard is the bootloader really and used tera term pro to dump rom etc. its seems to of hanged at the minute does it take a while to write?
im guessing i could go into the white screen mode and reflash an original orange rom?
New Original OS installed
Hi ive successfully installed a new OS so i presume the white screen is a bootloader. still my problem of powering off upon boot exists, so using this method i want to change the details below
OLD SETTINGS
IPL 2.21.0001
SPL 2.21.01ip
GSM 02.69.21
OS 7.7.7.7
NEW SETTINGS
IPL 2.10.0001 check
SPL 2.21.01ip SPL 2.10.0001 wanted
GSM 02.69.21 GSM 02.07.20 wanted
OS 2.10.1.22 check
Can i reinstall the wanted SPL/GSM from the white screen loader? does anyone know where i can get the files. SPV M600
Repaired 100%
I did it, its fixed charges now from USB data cable. and can enter tricolour bootloader. the problem was something wrong with the spl flash process ive redone that no errors excellent. im happy now
Will a ROM flash now?
Related
Just tried to upgrade my S200 with a 9100 ROM ver 2.8.7.1 WWE (by mistake of course) and I can't turn it on anymore. Somehow it didn't even warn about wrong ROM.
Tried to hardreset it but no luck. When I keep the camera button it goes to RGB only when connected to the charger.
When connected to PC, the red and blue leds keep flashing and my PC gives Error 260 when I try to revert back to the S200 RUU.
Does anyone know how to bring it back to life? Is there a way to boot it from SD card?
-
I-mate Jam
Qtek 9100
Qtek S200
Don't panic!
I did the same thing some time ago!
What you need to do is make sure that the battery is fully charged. (The flashing of the screen can be a result of the flat battery.) Unfortunately, it is not possible to charge the battery when the wrong ROM is installed, as the ROM obviously tells the Prophet how to charge.
Let's assume you have an okay battery.
1) Start the Prophet in Boot mode. This is done by pressing and holding the Camera button and then pressing the soft-reset button. Keep holding for about 7 seconds, and the coloured bands should appear.
2) Connect to PC using the UDB cable.
3) Run the correct ROM upgrade. You do not need to be paired with ActiveSync, as the update programs are intelligent.
4) If the update does not work (and it fails at 95%), then try again. If it still fails, try again and do a soft-reset mid-way through. This will kill the ROM upgrade and you should then be able to do it fine after that.
The really important thing is that the battery is charged before you do this. Unless anyone makes a USB cable that can charge AND connect to PC, then a fully charged battery is a must.
Let me know if this helped.
Check this Out
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!
Check this Out
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!
Re: Boot from SD?
zealerc said:
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!
Click to expand...
Click to collapse
I am a bit confused, does that mean that ALLOW USB CONNECTIONS has to be chacked or unchecked?
I did the same exact mistake. Now, my baterry is fully chaged (which I can check on another phone) but when I put it in S200 it shows that the battery has 0%. Conseqeuntly, when i unplug the power cord the phone dies. I have no way of running the new ROM on it. I tried running a bootable SD but it only installed part of the software. i read on this forum that such a thing happens and that one would need to run a full version ROM from a computer. So, how do I do it??? I am almost giving up all hope of ever making this phone work
Does anyone have a file to boot from SD and is it possible to run a full ROM from SD. Please help!
Hi,
after the download new ROM my MDA was fired!!
First I download a customized ITA rom and after, because the MDA work very slow, I downloaded the latest T-mobile ROM.
Now the MDA do not power up and do not charge the battery.....sems dead.
Can I recover it?
just an idea but I would start by trying to charge it with the wall plug that came with it, not a computer usb cable - if the battery is all the way dead it will not charge from the computer. If the light comes on, let it charge for a while and then try it out. If not I would try to hard reset while it is plugged in. If none of this works, enter bootloader mode and then connect it to the computer, and hopefully it will go into bootloader mode and you can flash a new rom.. If you need more details on how to do any of this, let me know, and please let me know if it works!
Hi....you fine.
I have recharge the battery and dowloaded the original Tmob rom.
Now is strange..
Same time power up...and same time no.
The ipl is 1.06 and spl is 1.03!!
My Qtek 9100 is dead also. I have the 2.24 ROM and it has been running great. I cant power it on and the light doesnt turn on when its plugged in. The battery is definitely not dead. Suggestions? TIA
try this...
try the suggestions listed here
however be warned that any of these will delete any and all data that may or may not still be on your device and restore it to just the fresh ROM...
Hi,
I have flash the rom 1.6 Tmob (IPL 1.06 SPL 1.03) but the MDA restart in loop mode!!
My phone powered up today. It's been sitting on my night stand for a week and it turned on today! Everyday I have tried to turn it on but I haven't had any luck until today...weird!
Hi,
I tried to USPL my P4350 (SPL & IPL 4.xx.xxxx) in order to update to WM6.1, using Herald-USPL-Beta3. Everything went OK until ROMUpdateUtility kicked in, and gave me an error: FILE IN USE.
So I started the ROMUpdateUtility again, with the screen still blank, and suddenly the P4350 turned off. I'm 100% sure the battery was at least 90% full during USPL'ing, so why it turned off; I have no idea.
Problem is: I can't power up the device anymore. No LED's, even when attaching it to the power adapter.
Any tips on how to fix this, or is it fair to say my device is now really DEAD?
Thanks!
Some suggestions of a Junior Member.
1st. Try a soft reset. Didn't work? Go to Step 2
2nd. Try a hard reset. Didn't work? Go to Step 3
3rd. Pull the battery off. Put it again. Try to turn it on. Didn't work? Go to Step 4
4rd. Wait replies from advanced user. End.
Thank you for replying
However none of the options you mentioned worked out.
I'm stuck waiting for some expert guidance here
Hi, it's been a while, but today I finally made -sure hope so- some progress..
I purchased a HTC Touch HD two weeks ago, from which I plugged in the power adaptor to see what my P4350 would do. (specs are the same btw as the P4350 power adaptor; output 5V, 1A) On this attempt however, the left LED on the front of the device turned RED for about 5 seconds before turning off again. I plugged in the adaptor again, and it lit up RED again. However, the device did not respond to an attempt to power it up.
What does this mean? Is it not dead after all?
Any tips on what to do?
Thanks again.
Wow man, I'm getting somewhere now!
I got the device powered on holding the RESET+POWER+CAMERA and it now hangs on the IPL + SPL screen.
What is very strange is the following:
IPL 1.08.0001
SPL 1.08.0001
as to where these were above 4.xx.xxxx before I did the USPL'ing. I am a 100% sure.. (not so sure anymore now to be honest.. )
The screen displays USB in the left bottom corner, because it is connected to the USB power supply.
I'm afraid to turn it off because it might not turn on again...
Where do I go from here?
Well, I finally got my P4350 to work again
I noticed I was able to start into bootloader mode using CAMERA+RESET, unlike previous attempts to do so. I don't know what caused the device to boot after 6 weeks, but I guess attaching the Touch HD power adapter did the trick.
At first I followed the instructions at topic "Goldcard for Herald", but somehow I wasn't able to make the MicroSD card bootable using my HTC Touch HD for the formatting.
Instead I went to page 5 of the topic and discovered this comment by leptir79, who stated the creation of the Goldcard could easily be done from a DOS-prompt in Windows, with the MicroSD card in the SD-cardreader on a PC or notebook. And this is what did the trick for me:
- I put the SD-card in my notebook cardreader (drive W: ), opened a DOS-prompt, and ran the following command to format the SD-card with the correct priviliges: FORMAT w: /FS:FAT32 /A:4096
- After that I copied heradiag.nbh to the blank MicroSD card to see if my P4350 would boot from the MicroSD card. And it did. From this tool I ran some diagnostics tools to see whether my device was fully functioning, and I got no errors. I noticed that among the diagnostics tools there was a tool to Flash the device with a new ROM
- So I downloaded HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe, extracted RUU_signed.nbh to the root of my MicroSD card (along with heradiag.nbh), and renamed RUU_signed.nbh to heraimg.nbh.
- I started the P4350 into bootloader mode, booting from the MicroSD card. Heradiag.nbh booted up, and I chose to use the Flash ROM utility that came with heradiag. The device automatically found heraimg.nbh, and started the flashing procedure for my device. After confirming, the flashing started.
After a few minutes my P4350 rebooted, and my device is now running Windows Mobile 6.0. Everything seems to work just fine now.
So, if you don't have a second (working) WM device, but do have an cardreader on your PC or notebook, this really is the best option to create the Goldcard imho.. (even if you do have another WM-phone, really, try this procedure first before installing ActivePerl and all the perl-scripts)
Thanks everyone for all the procedures and help. You all did a great job, but most credits in this case go out to leptir79 who gave me the breakthrough in getting my -left for dead- device to work again.
This is a gold trick thats what i'm waiting for...
I have my heralds bricked since 2 months ago... Yup....really bricked...means cant do bootloader mode or hard reseting on device...
And already sent it to the HTC care center, and they ask for mainboard replacing...which is too expensive for me...400US...later cancelling it...
Searching out this forum, and didn't find a solution to reprogramming OMAP via JTAG...then my research suspended...
Untill I found this...
All I need...just to enter to the bootloader...powering up the brick
Can't wait to try this method @home...ASAP...
For now...just looking for 5V, 1A Charger first....
TIA frummel...
hera100
hie i have a hera100 does not detect on active sync when i try to update rom stops at 2% try diffrernt roms some stop at 7% my IPL 4.14.0002 SPL 4.10.000 i tried formating my 2gig and put heraimg on it nothing happens. pliz help how do i do it now phone shows three colors i cant hard spl coz of active sync. ithanx in advance
Attach phone to a computer with a mini-USB cable and install a RUU ROM.
I flashed my htc elf (t-mobile touch) with onyx ultimate, just over halway it froze, then my whole pc froze and crashed, the phone turned off and i havent been able to get it on since, no lights, no screen, nothing
PLEASE HELP
I have tried:
power button
soft reset
hard reset
bootloader mode
plugging it into my pc and my mac to charge it but still no power
tried plugging it into my pc without the battery to see if the orange light comes on
Any Ideas??
I'm not exactly an expert but I'd have thought attempting to flashing a ROM shouldn't break its power supply. It doesn't add up. You mention the orange light, but does it actually come on or not?
I'll assume you flashed a USPL or you probably wouldn't be getting past 3% in the first place lol.
strange one
yea, it was all ready to be flashed, it was previously on a geniric htc rom that i put on it.
there is no orange light at all, no nothing, i cant seam to work it out, i mate has the same phone and im gonna try his charger and battery when i see him tomorrow but i still cant see how flashing it would affect the power, unless the device is blank now and it doesnt even know what the buttons do e.g the power button is not assigned to do anything.
try with another fully charged battery... and ELF/ELFin Golcard method, with a suitable flash file (like a Original one)
Just my 2 cents...
Try put the battery with the camera button pressed..
i have had the same problem
pres start button and fotos together
will appear 4 colors and ipl ..... and spl ........
if its appear: ipl 2....... and spl 1.11.000 you must upgrade your spl
read : http://forum.xda-developers.com/showthread.php?p=3038443&posted=1#post3038443
Hi,
I really need help seriously
Today I upgraded my P3450 to Onnyx Ultimate 4.8 and it was successfull.
Then I think again, I want to go back to original shipped ROM that I've backup before.
I do as mentioned on this page :
http://wiki.xda-developers.com/index.php?pagename=Elf_HowtoDumpRom
I used the complete backup to restore the ROM. ( I made 2 backup files, first only OS and Ext ROM, 2nd All of them).
It run success until 100%, then the device reset, and after that it never power ON again.
What should I do?
Please, HELP, it is about one week I bought this PDA (
Thanks
Please Note the condition for the device :
1. With the battery inside, I plug in the charger, the orange light never ON. Completely dead.
2. There's no problem with the battery. I have friend who has ELF , I put my battery on his ELF, his ELF run normally.
Try removing battery than boot your phone in bootloader.
If it starts try flashing a shipped rom.
thanks for your reply, I've tried but nothing happened.
What was my mistake?
Before I upgraded, I've dumped my ROM. using the utilities as mentioned here : http://wiki.xda-developers.com/index.php?pagename=Elf_HowtoDumpRom
I made two backup :
* One backup with the OS and ExtROM only (for others to use)
* And another backup with everything included (for yourself only, for warranty or selling purposes).
After that, seems everything to be Okay, and then I did as mentioned in this post : http://forum.xda-developers.com/showthread.php?t=445666
and then I flash Onyx Ultimate 4.8. And, I did it!!!
But then, when the device reboot, I saw a thin horisontal line on the top of the LCD. As I worried about my device, then I decided to go back to original ROM.
I did again this : http://forum.xda-developers.com/showthread.php?t=445666
this is to flash any SPL: either update to hardspl this way or flash another spl over hardspl. (copied from other post)
0. make sure your device is synced to activesync!!
1. Run the elf-uspl.exe from ELF_USPL_2.26.0000.zip
2. Watch Screen and Press Enter When Asked.
3. Screen should Jump to White on Phone and on PC Flashing Loading Bar will Show.
4. Stuck in Black Ducky Loading Screen?, check Active Sync Connection or Do a hard reset on Phone first. But be sure to do the last Actual Flashing in White Screen. Sometimes this needs a few tries to go through white screen.
5. Done.
Click to expand...
Click to collapse
And I overwrite the .nbh file with the Complete ROM that I have dumped before.
Everything seems to be Okay, it uploaded 100%, then the disaster happened !!!!
The device went off, and it never get on again. Until now. I've tried many ways to make it On :
1. Remove the battery, and then plug it again, turn the power ON, and it still go off.
2. Remove the battery, plug in charger with no battery, try to power ON, still off.
3 Remove the battery, plug in the charger with no battery, push the camera button and reset button on the same time, nothing happened.
Please help me, I really frustated here What was my activity that could cause a damage to my Elf?
I've tried a repair man and he said that there's no J-Tag to turn on my P3450, I must change the machine to the new one....
My device information before it's dead :
HTC Touch device information - by dsixda
Touch version : Elf
Device ID : ELF010000
CID : DOPOD001
IPL : 1.11.0002
SPL : 1.11.0000
ROM Version : 1.11.707.1B
ExtROM Version : 1.11.707.101
Operator Version: None
AKU Version : 0.2.3
Page Pool : 8 MB
RAM Size : 64 MB
ROM Size : 128 MB
Model No. : ELF0300
Part Number : 99HDM034-00
MCC+MNC : Not found
Please, any help would deeply appreciated !
Thanks
Please, any help would deeply appreciated !
Thanks
Hi, I had same problem the other day just I could not power up my device after down grading, my device just rejected to work and went dead.
So I made the following steps then I was able to get it work in bootloader option only:
- Take the battry out
- Take the sim card out
- Take the memory card out
- wait for 1 to 3 minutes
- replace the battry back
- hold on the camera botton then press the power botton and hold it.
if it did not work, bring the battery out then replace it back then try press
the camera botton and press the power botton while keep on clicking the
camer botton, it should come to bootloader status. Wish you good luck.
sam62 said:
Hi, I had same problem the other day just I could not power up my device after down grading, my device just rejected to work and went dead.
So I made the following steps then I was able to get it work in bootloader option only:
- Take the battry out
- Take the sim card out
- Take the memory card out
- wait for 1 to 3 minutes
- replace the battry back
- hold on the camera botton then press the power botton and hold it.
if it did not work, bring the battery out then replace it back then try press
the camera botton and press the power botton while keep on clicking the
camer botton, it should come to bootloader status. Wish you good luck.
Click to expand...
Click to collapse
Hi..thanks for your answer. I've done it but nothing happened. I really start to worry that my device really..really death.
When you're in that condition, did you plug the charger to the PDA while the battery still on it? Was the LED light up, green or orange? My problem is, there's no light up at all...no response
Could you make what happened clearer?
Did you flash an entire NBH image, SPL & IPL included, while using HardSPL?
Trying to replace HardSPL with a stock SPL has caused issues before.
HardSPL cannot be simply overwrited by a stock SPL.
Check out this thread to remove HSPL.
http://forum.xda-developers.com/showthread.php?t=342744
Though it might be bricked...try the Elf[in] unbricker...
Lumic said:
Could you make what happened clearer?
Did you flash an entire NBH image, SPL & IPL included, while using HardSPL?
Trying to replace HardSPL with a stock SPL has caused issues before.
HardSPL cannot be simply overwrited by a stock SPL.
Check out this thread to remove HSPL.
http://forum.xda-developers.com/showthread.php?t=342744
Though it might be bricked...try the Elf[in] unbricker...
Click to expand...
Click to collapse
I think you're right on this one : Did you flash an entire NBH image, SPL & IPL included, while using HardSPL?
I thought I wanted to get back to factory default by flashing the complete NBH file, which include :OS, Ext. ROM, Radio, Splash, SPL, and IPL H3.
I run the "elf-uspl.exe" in the folder named "USPL_2.28.0000 with IPL_2.27", which I downloaded from this thread : http://wiki.xda-developers.com/index.php?pagename=Elf_HowtoDumpRom
(it was extracted from TOOLS).
after that I uploaded the complete ROM that I have backed up before. Actually I made two backups, one complete, the other only OS & Ext ROM.
guess my mistake is I restore the complete one.
If my device can not power ON at all (even when I plug in the charger, the light indicator not ON), can I still repair this?
htc will nt accept it ..but u can try with service centers..
There's one new fact I just found out today.
I have a friend with the same ELF as mine.
When I put my battery on his ELF, his ELF also can not power ON. But I still can charge my battery on his ELF and it shows 0% !!!!
I firmly believe that yesterday when I downgraded my ELF from Onnyx to its backup original ROM, the battery is still more than 90%, as I've checked it before.
Is it possible that teh conflict of Hard SPL and my original backup ROM drain the battery so fast? I am now holding my friend's battery, but I scare to put it on my ELF as I don't want to damage his battery, worry that there's some short circuit.
The other problem :
1. When I put my battery on my friend's ELF and plug in the charger, the light indicator shows orange light, sign that it is being charged.
2. When I put my battery on my friend's ELF and plug in the charger, the light indicator shows nothing, it is definitely OFF.
Any suggestion for my case?
Charge your battery in your friend's phone and try it in your phone ... and tell us....
Confliction
bombom81 said:
The other problem :
1. When I put my battery on my friend's ELF and plug in the charger, the light indicator shows orange light, sign that it is being charged.
2. When I put my battery on my friend's ELF and plug in the charger, the light indicator shows nothing, it is definitely OFF.
Click to expand...
Click to collapse
I'm sorry if I'm not getting it right.. but you are contradicting yourself..
I mean when you put your battery in your friend's elf and plug in the charger.. does the indicator show orange light or not???!!
Fa7my said:
I'm sorry if I'm not getting it right.. but you are contradicting yourself..
I mean when you put your battery in your friend's elf and plug in the charger.. does the indicator show orange light or not???!!
Click to expand...
Click to collapse
Yes, it is charged and shows orange light on my friend's ELF.
But when I put on mine, the light doesn't turn ON at all. Seems that mine can not charge the battery.
I've tried this way :
1. removed the battery and left the device alone for a few hours - no luck
2. charged the battery using a wall charger - no luck
3. removed sd card and sim card and tried the alternative reset at this link http://wiki.xda-developers.com/index...ame=Elf_Resets using a wall charger. device booted into tricolor mode.
4. did the same alternative reset with a usb charger. once the device was in tricolor mode, flashed a cooked rom.
But unfortunately, there's nothing happened
bombom81 said:
4. did the same alternative reset with a usb charger. once the device was in tricolor mode, flashed a cooked rom.
But unfortunately, there's nothing happened
Click to expand...
Click to collapse
sorry if i'm asking too many questions but what does the tricolor boot screen show?? (IPL/SPL) cause if the SPL is x.xx.cmon .. then HardSPL is still there and you would (probably) be able to flash another ROM..
is there a small "RUU" written the top write corner of the screen?? (written in white)
bombom81 said:
4. did the same alternative reset with a usb charger. once the device was in tricolor mode, flashed a cooked rom.
But unfortunately, there's nothing happened
Click to expand...
Click to collapse
sorry if i'm asking too many questions but what does the tricolor boot screen show?? (IPL/SPL) cause if the SPL is x.xx.cmon .. then HardSPL is still there and you would (probably) be able to flash another ROM..
is there a small "RUU" written the top write corner of the screen?? (written in white)
Fa7my said:
sorry if i'm asking too many questions but what does the tricolor boot screen show?? (IPL/SPL) cause if the SPL is x.xx.cmon .. then HardSPL is still there and you would (probably) be able to flash another ROM..
is there a small "RUU" written the top write corner of the screen?? (written in white)
Click to expand...
Click to collapse
NOP, I am glad if somebody ask, means that there's someone who watching my thread.
The problem is, my Touch is not ON at all. totally dead. No light indicator, no power ON, just dead.
updated :
I have charged my battery until full 100%.
I did put on my device, holding the camera button while power ON, and still nothing happened. just dead.
did u try a hard reset ?? you can do it by holding the Call & End buttons and reseting with the stylus.. a confirmation msg will appear press the OK button (the large one in the middle)..
hope that will do you any good :S
I did hard reset, many times, but still can not work
I almost desperate thinking my dead ELF need some miraculuous to make it ON
hey bro i sent you my e-mail in a private msg so we can try solving this together in a better way..
Did you at least read the sticky thread entitled "Unbricker"??
If you cannot get to bootloader it usually means your battery is dead... or the device is fried. Try charging it on the wall charger for at least 20 minutes again.
only soln is to replace the entire motherboard
i did the same thing to my friend's mobile and it got totally dead
then i read that never to reinstall the original rom n never to downgrade your spl or roms
only soln is to get it repaired or replaced if under warranty by htc no one in the market can help u even htc will replace it they wont b able to boot it up hence if under waranty ur board will b changed for free
else buy a new one simple buddy ....