Database Users

Bricked Hermes (SPV M3100) while flashing SPL - any help or sugestion are wellcomed

All started with trying to upgrade(rewrite) the GSM part because the Hermes had problems with phone part - when trying to call - the phone stop responding, bus the pda part sill worked.
So - I tried and tried and tried again, reading many threads about HARD SPL,Flashing radio, etc. Nothing worked..
In the end "i managed" to kill GSM - phone had "No Gsm" on boot-up.
From there i tried to downgrade SPL to 1.04 so that i try to "raw" rewrite the GSM part.
But something went terribly wrong, and while downgrading SPL, the phone suddently shutdown and never opened again.
Now i have the folowing situation: NO BOOTLOADER, no usb conectivity, nothing
This means that i cannot connect via USB whatever i try.
Is there any hope for me? or is it TOTALLY BRICKED?
Any help is apreciated!! I can even dismantle the mobile if there is any way to flash it via some kind of jtag connection...anything ...

The folks at www.imei-check.com can do the JTAG flashing. Just email them. It would be costly for you to do it yourself...

Are you saying that the phone won't turn on at all or that it does but you can't get a bootloader screen?
Have you tried taking the battery out for a while? Have you tried flashing an OEM rom and radio compatible with your device off an SD card?
All of this info is in the wiki, as are OEM roms you can flash.
Let us know how you get on.
Good luck.
WB

Try this:
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber
5.) Soft Reset

@wacky.banana: The phone is totaly dead: no bootloader, doesn't boot at all, doesn't seem to have any USB conectivity at all. Flashing from micro sd doesn't work : probably because the bootloader isn't working.
@drummer10630: i'll check with imei-chek about jtag flashing, especially the price and shiping costs.thanks
@markafreeman: I tried, but when i put the battery in, the red light goes off, not to amber . no soft or hard reset helps. not even leaving the battery out for 2 weeks - i had tried that too . thanks anyway.
Anything else I can try? - phone totaly dead, no bootloder, no usb conectivity - cannot use mtty, cannot flash from microsd

I had to get a replacement device at that point when it happened to me.
Maybe someone else know a way to get it working.
Good luck.

get onto orange
tell them you dropped the phone
and it crashed and wouldnt turn on
so you managed to hard reset it
and it crashed an ****ed up
they'll replace it
well they will send it to HTC
who just replace the handset rather than repair it

Hi dancameo2k , maybe you will not remember but plz:
I ve bought recenty an spv m3100, im effortless trying to flash the rom to an wm6 version.
Like you ive started with the hardsppl flash thing to prevent bricking it and prior to sd flashing... and im not sure if its workin...
plz can you explain in detail how did you bricked it??? thx!!!!
the rom you used to flash was an american version or european one???

Cincular 8525 stuck in Bootloader

I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?

Zulu137 said:
I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?
Click to expand...
Click to collapse
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help

Asfarizal said:
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help
Click to expand...
Click to collapse
Manage to solve the problem ...thanks WIKI !!
Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus
Then Flash to any ROM you want !!

Thanks .... But
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.

1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......

Thank You
I will follow the instructions you gave and try to get it going this weekend.
Thank you so much for your time

Zulu137 said:
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.
Click to expand...
Click to collapse
Looks like you've got a lot of reading to do, and a problem to sort out. Firstly a couple of answers...
Schaps is a Rom Cooking guru (makes custom versions of WM5, WM6 etc). When you get your phone sorted out I'd recommend trying one of his roms.
Hard SPL. The SPL is part of the bootloader which effectively dictates how a rom is flashed and what roms can be flashed. HardSPL is a custom version of this which allows you to flash any rom from any carrier. It also protects against a bad flash in many cases. It is recommended before you try flashing any new roms or radio roms. Use Hard-SPL-V7 at the bottom of the first post here.
The Rom upgrading software is contained in any of the cooked or carrier supplied roms. It is normally a .zip file which cotains 2 files: xxxxxRUU.exe and RUU_signed.nbh. You run the .exe file from your PC when connected to your phone via USB. More details of how to do this are in MrVanx's guides. Also other resources here.
Now to try to sort your phone out...
What is displayed on your screen when in bootloader mode? It should be something like this:
HERM200
IPL-1.04
HERM200
SPL-2.10.Olipro (This is HardSPL V7)
If you don't have an Olipro SPL then you need to get HardSPL onto your phone. If you haven't done any upgrading and have had the phone from new then I guess you don't have hardSPL.
Now you need to fix your USB Malfunctioning problem. I can't help too much here except to suggest trying a different cable, different USB port or different PC. Also, if you are running Vista try an XP maxhine. When you connect to the PC does your phone show Serial or USB on the screen? If you can't get a USB connection, all is not lost - you can re-flash your rom using an SD card, method here.
There is a thread about un-bricking phones which may help.
There are various diagnostic tools (which can also screw your phone if used incorrectly). The favourite of these is MTTY but you need a USB connection to use this.
If your phone is in warranty I'd recommend getting your supplier to sort it out, but if not I'd try to re-flash an ORIGINAL supplier rom (Cingular I guess). You can get links to the official supplier roms here.
I think (might be wrong) that sometimes when stuck in bootloader you need to flash an official rom, not a cooked one to recover your phone - then you can run HardSPL and then flash cooked roms again.

Cingular 8525 stuck in bootloader
Thanks for the reply ... lots of great input.
Now to answer some of your questions.
1) When I power up the phone (only pushing the power button ) it goes straight into the bootloader screen without pushing any other buttons, and it displays
HERM100
IPL-1.01
HERM100
SPL-1.06
Then at the bottom in the white bar it says "Serial"
The only way that i have found to power it down again is to remove the battery, there is no response from any single buttons after it is in bootloader
the soft reset and hard reset work but it just goes right back to the bootloader screen after.
2) The USB malfunction. This only started after the phone "crashed" and before that it worked great ... well i only used it to sync up to my work pc for the contacts and to get pictures onto my hard drive.
all the PC's that i use are running XP. I have tried my home PC and my Laptop
and the work PC and all of them have their own cables and they all say the same thing ... "the USB device is malfunctioning"
I am sure that when i get the phone going again the USB will start to function again.
3) Phone warranty ... I bought the phone off e-bay from a store in new york about 10 months ago as a "new unlocked cingular 8525" it was new and unlocked, but i have no idea how they unlocked it. I would assume that there would be no warranty now and in any case i live in Canada and would have to ship it down to the states to an AT&T repair center and that sounds like a nightmare to me with the customs and so on.
I will give you a little more background on the problem. the phone worked like a charm without any problems at all for the 10 months that i had it, then the morning of the crash the phones alarm did not go off in the morning and i was almost late for work ... i did not pay it any further attention untill at 3:26pm
that afternoon the alarm went off ??????? (it was set for 6:05am) so i checked the main clock time, it was right. I then checked the alarm time, it was right ??? So i figured that something must have just got confused, so i powered down the phone with the power button to just restart it and while it was powered down i removed the battery to take the oportunity to to clean all those fuzzies and dust that collect in the battery compartment out and put it all together and powered it up again (just by pushing the power button) and this wierd red, green, blue and white screen appeared and that is all that i have seen since ???
I hope that answers your questions and i will start going through the links that you sent and get to reading ... will there be a pop quiz ... lol
Thanks again for your time and i very much appreciate all the time that all of you have spent on me and my phone ..... I know that you all just feel bad for me because i now have to use a Motorolla V551 ... lol

Great Work
ultramag69 said:
1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......
Click to expand...
Click to collapse
Thanks a lot man & great work i unbricked my Herm100 with method u mention above thanks a lot & great job keep it up

I also have this problem.
I d/l Hard-SPL-V7
and when i run RUUWrapper.exe
I get an error saying the application failed to initialize properly (0xc0000135)
What's going on?
How do i fix this?
this happened when i was trying to unlock the phone.
Thanks

need help
when i switch on my orange herm100 it shows On the bootloader screen is displayed:
HERM100
I PL-1.01
HERM100
SPL-1.40.01ipro
history : i buy unlocked orange phone
fewdays back i found no imei ,
yesterday i try to flash by micro sd but in gsm stage its gets hang no progress after extrom stage
IPL - OK
BOOTLOADER - OK
SPLASH1 - OK
SPLASH2 - OK
EXTROM - OK
GSM - (NO ACTION)
OS -
i tryed several time no action, i cant connect by mini usb.
PLEASE help me
tell me which it the right rom to chose? step by step procedure..
how to rectify imei?
thanks and regards
kirtibas

kirtibas, sorry it took so long to reply, 1st thing I'd do is upgrade to SPL 2.10 olipro. This is safer to use than others. then I'd suggest reflashing a stock rom to see if that works. After stock rom works then use a cooked rom as your heart desires... Cheers...

i reeallyyyy need somebody's help with unbricking my phone.. please hellpppp!!

alright.. i made a similar post to this before and i came across the wiki...
well i can't view what my SPL or my IPL because as soon as i turn the device on, all that shows is the boot loader screen and displays serial on the top with 0.16-0.90 in red characters on the bottom (I'm not sure what those are)...
here are the only details that i know about my phone:
I DON'T have hard SPL
My Original ROM i was using before was an htc windows mobile 5 rom
The reason that my phone is bricked right now is because the usb cable disconnected in the middle of the flash
I'm using Windows Vista for flashing
Computer won't recognize the phone when on usb
My phone (qtek 9600) can't load the operating system
*EDIT*
THE PHONE IS STUCK ON BOOTLOADER WHEN I TURN IT ON, NOTHING ELSE, BUT THE BOOTLOADER SCRREN DOESN'T SHOW MY SPL AT ALL.
ALSO, MY COMPUTER DOESN'T RECOGNIZE THE PHONE....... MY PHONE HAS A TYPE 2A BRICK
Helping me will be greatly appreciated
come on.. I'm without a phone

Do you have a 2GB or smaller SD card? Copy a rom image to it and rename it HERMIMG.NBH
Turn it on and you might get lucky!

Just make sure its stock rom that was supplied, or the updated WM06 version as the CID should check out then...
vwkess forgot to mention, reset into bootloader, hold power, ok button and reset with stylus. Hold all buttons in until you get to the tri-colour screen. If it works, follow the prompts....
Cheers...

hi,
i think i can hlep.
i had recently bricked my phone with a custom wm6 image, it worked fine for two days and then i reboot, and all i see was the welcome image, nothing else.
so what i did is -
i pressed the hard reset buttons - power + OK + SOFT RESET (Stylus), kept it pressed for 3-4 seconds, the fone rebooted, the screen was full with some colored bricks i connected my fone in USB and on screen i saw USB.
I then again flashed my fone with the working update, it worked perfectly for me, try may be you can get some luck
ps - before doing all these, i turned my fone off by removing the battery, i removed sim card and mmc card as well.
regards

That may work too, but again, try to flash with a stock rom, untick "connect with USB" in activesync and then try.
Make sure you go to boootloader screen, instruction in rajivlodha's post, before you connect to the pc.
Goodluck...

I need some help as well.
I think I may have bricked my phone. It's a rooted htc hero cdma. I'm running cyogenmod on it and it was working fine, until using metamorph to apply some changes to the theme.
I went to reboot, and it now it won't load past the htc screen. Even when i try the key combination to put it into recover mode. I didn't install a nandroid backup, and i'd be fine with just completely wiping my phone. help is appreciated.

HTC P4350 dead after rom flash!!

Hello i tried to flash mine P4350 with at first Hard SPL , works fine after that place a custum rom, seems to works fine, but after a soft reset, NOTHING
even no LED activity. booting with holding camera button for 3 seconds, shows greens screen with ipl 1.08.0001 and 1.08.0001 and then is turns off..
IS this the end for the HTC????
Hello, ik can put a rom on the sd and boot it say illegal certificate?
Flashing from usb with romupdate utility says error 300 invalid update tool (rom update utility = 03.11.3.1)

if u are abel to get to the tricolor screen im sure you could reflash to another ROM (maybe it was a bad ROM/bad download) try flashing a ROM using the sd card (if you dont know how to flash from sd card search on it firs its all over the forum) make sure your battery is higher than 50%. well good luck.

Your SPL is not 4.0 or above. The HardSPL thread warns you against using the HardSPL on a SPL that low because it bricks the phone. You'll have to search for the Herald Goldcard method to revive the phone.
Other than that, this is not the right sub forum to ask those questions in.

Please I need help!!!
My rom flashing stucked on 80% over HTC herald and I had no other choice but to restart the phone and now its completely dead. tri color screen is not coming also.
Please help

I have 2 heralds which are having problems with turning on.
This is what works for me:
1) Take the battery out for 10 seconds
2) plug the charger into the phone
3) put battery back in the phone
4) press POWER button for 3 to 5 seconds
Try it few times - works for me fine, but not always !

[Q] Help!

Hey guys,
Sorry to be a burden but I'm having a few issues with my hd2, and being a noob I didn't really know where to turn except this forum.
Basically my dad bought the hd2 from the UAE early this year and it all worked fine on stock settings for about 6 months. In the last few months, however, the phone started to lock up, and it got to the point where it wouldn't even boot properly.
In an effort to fix the problem I went with a hard factory restore, however, this seems to have caused more problems as now the phone is stuck in the bootloader.
I've been searching for hours, and have come to the conclusion that I need to update the flash? and then possibly install a new rom on the phone?
My major issue in doing this though, is that I can't seem to connect to activesync while the phone is in the bootloader.
Please help me sort this out.

First of all lets make sure that your trying perform the hard reset correctly.......
You need to hold down both volume buttons whilst the phone is turned off..... Then tap the power button and keep the buttons held down.......
Release them when you see the confirmation screen.........
Powering on while holding only the vol down button will take you to bootloader....
If you need to reflash the device then have a read of this thread here....
If its a "Tmous" HD2 (green and red call/hangup buttons) then you need to read this one
When connecting to the pc in bootloader you should see the word "serial" at the bottom of the screen change to "USB".......
Might be worth checking the text on you bootloader screen for any irregular looking characters, there have a few cases of people with corrupt bootloaders, usually these will display odd looking characters at the top. This is quite rare though.
If you want to flash another stock rom then you wont need to worry about HSPL just download the appropriate ROM and follow the instructions on screen.
Start off at the HTC site and input your serial number to see which ROM is suitable for your device.....
If none of that helps then hold out for some advice here from someone with better knowledge of these things.....

Ok well I've just tried to do the hard reset in the way you've described and had no response from the phone. I had to remove the battery from the back to actually power down the thing as nothing else seemed to work. I can't actually seem to start it up again now =S
Thanks for all the info, I'll keep trying to get it started. I'm downloading the stock rom from the htc site. Hopefully I will find a way to install that.
Also, when the bootloader was up, there weren't any odd characters that I could see. It all seemed pretty standard. It had the current rom driver which was 1.42 or something and a few other lines of info.
Thanks for the post.
edit: perhaps the battery is dead?

No problem.
Is it charging when plugged in and turned off?
If so let it charge while turned off for a while and then try to boot........
If you cant get to bootloader and establish a USB connection then you could try flashing the ROM from the SD card.
rename the rom to "LEOIMG.nbh" place it on the root of a freshly formatted (fat32) sd card and turn on the phone holding vol down..

conantroutman said:
No problem.
Is it charging when plugged in and turned off?
If so let it charge while turned off for a while and then try to boot........
If you cant get to bootloader and establish a USB connection then you could try flashing the ROM from the SD card.
rename the rom to "LEOIMG.nbh" place it on the root of a freshly formatted (fat32) sd card and turn on the phone holding vol down..
Click to expand...
Click to collapse
To be honest I have no idea if it is charging whilst turned off =S All I get is the bootloader when it decided to turn on and that gives no indication of power level so I really have no idea. It makes updating a rom pretty scary haha.
So I just attempted to install the default rom from teh htc site, but failed due to the lack of activesync. It was strange though because the updater managed to change the screen on the phone and get to 1%. It then crashed and I had to go through this recovery process.
I will have to try this SD card process I guess. Could you perhaps link me to a more in depth guide to how to do this?
Thanks a lot for your help I really appreciate it.

you should get a red light up near the earpiece to indicate that its charging........
try this video for flashing from sd card......

I am not getting a red light flashing? But it doesn't seem to be running out of charge. I'm still having lots of trouble
It would seem that I need to install this hspl before I do anything, however, I can't install that if I can only access the bootloader screen. Does this mean my phone is bricked?
I want to be able to set up a rom straight from SD, however, I have no idea where to start. That video just seems to send me in a big loop.
Perhaps you could link me to a simple rom that I can attempt to load via sd card?
edit:
I seem to have somehow fluked an install of HSPL 8G XE.
I have no idea how this happened or whether it is good or bad.. but at least something has happened.

Hmmm
installing hspl is covered here
as long as the word "serial" is changing to "USB" on the bootloader screen when you connect to the computer you should be ok.......
You dont need HSPL to flash via sd card but I think that video was directed more towards people installing cooked ROMS from XDA.
Installing a stock rom will automatically overwrite HSPL so unless your planning to flash a custom ROM then installing HSPL is pointless........
You might be better off installing a cooked rom. (Artemis, Dutty's)
They tend to run better than stock, if you get one running then it will be easier to get back to a stock rom (if you want to) than the situation your in now.....
This is from the flashing guide;
Flashing Via MicroSD Card
NOTE (PLEASE READ): If you flash a Stock Rom via microSD Card then it will overwrite your HardSPL with a stock SPL included in the nbh file. This does not apply to custom roms as they do not include an SPL. BE CAREFUL!!
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the LEO Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to LEOIMG.nbh
4. Copy the LEOIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.

Reckon you could link me to one of those roms? I think we're getting pretty close now.
Your help has been great I can't thank you enough.

Your welcome
You can find Dutty's ROM here
or the Artemis ROM here
Have a quick read and see which one you think you'll prefer, to be honest I think they're both pretty similar to stock but with a lot of the crap taken out....
Just follow the steps in the first link I posted and you should be good to go.

Ok new problems.. Can you believe it.
I seem to have tried everything.
Basically I can install of a sd card, but when it gets to the end of the install and I restart instead of booting into a OS it boots to the tri colour screen, and starts the install process again.
Also, I have attempted to install via usb and have had varying success.
As I have already said, I am able to install hspl, however, when I try to flash I get to varying percentages below 30% before the whole thing freezes.
I now have an error that says Upgrade Rom code error Please Try Again.

Sorry i dont mean to hijack ! but will any of you be kind enough to help me here..
http://forum.xda-developers.com/showthread.php?t=879980
thanks !

Ok so I followed the steps and still to no avail.
I am able to boot using the sd card method, however, the same problem occurs with each rom version. Basically as soon as I reset the device it pretty much switches itself off, then I can't turn it back on, once I finally do turn it on, it restarts the process like it never happened.
The other issue is again the active sync problem.
With most of the the usb connections I am able to connect and get a little way through the install (most I've got is 15%) then it just freezes up and I get the 262 error

Your best bet is to try flashing with a freshly formatted (FAT32) 4gb, class 2 card.
I know, sounds pretty specific right?
You wouldn't think it would matter?
I have tried flashing with 16 gb class 2, failed at the radio step
Tried with a 8 gb class 6, failed at the radio
4 gb, class 2, flashed successfully.
Seems our HD2's are picky about what cards they'll take a ROM from for some reason.

Alright I'll try that, my next issue is which is the stock rom for the phone =S
It was bought in the UAE and I'm currently in Australia.
edit: Also I read somewhere that the constant bootloader screen can be caused by a bent battery pin?
Edit2: I have attempted to do that, however, now the bootloader will accept the card, then just sit on loading...
I'm pretty sure this thing is bricked.

tombm said:
Alright I'll try that, my next issue is which is the stock rom for the phone =S
It was bought in the UAE and I'm currently in Australia.
edit: Also I read somewhere that the constant bootloader screen can be caused by a bent battery pin?
Click to expand...
Click to collapse
I've heard of bent battery pins being a pretty common problem, causing usually just the phone not to charge properly. I've personally never heard of it causing constant bootloader, but it's definitely worth checking.
It's weird that it's such a common problem, my usb/charging port is broken, so I have to use an external charger. I change my battery on average twice every 24 hrs, and I've never bent a pin

Ok, new info, apparently because the device is for the middle east it does not support stock 3.14 roms. What does this mean for me? Am I bricked.
http://forum.xda-developers.com/showpost.php?p=9614007&postcount=30954
Click to expand...
Click to collapse
That's the post I found the info in. All of that info matches up to mine except my original image was 3.142 I think =S

Firstly, your phone is not bricked - a bricked phone is responsive as a brick.
Can we start from the begining?
What does the Bootloader Moder screen say (with and without the USB cable connected)?
What ROM (and if custom ROM, what RADIO) have you flashed and are trying to flash?

fred_up said:
Firstly, your phone is not bricked - a bricked phone is responsive as a brick.
Can we start from the begining?
What does the Bootloader Moder screen say (with and without the USB cable connected)?
What ROM (and if custom ROM, what RADIO) have you flashed and are trying to flash?
Click to expand...
Click to collapse
Alright from the beginning.
Basically about a month into using the phone in Australia it became very unresponsive to the point where it would not boot at all. We left the phone for a couple of months, however, after seeing a friend rom android I decided maybe it was time to attempt to fix this phone.
Some more info:
When I attempt to do any sort of ROM update there is nothing in the 'current image' part so for example it will say update to Dutty 3.6 but it's updating from nothing, does this mean there's no firmware there?
In the bootloader I have:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MICROP(LED) 0X05
MICROP(TOUCH) 0X40
Without USB cable in I get Serial in the white part down the bottom, with the USB cable in + plugged into computer I get USB.
Just to further clarify. In regards to the ROM I have installed. I simply don't have anything installed. There is a bootloader, no image, no bootup. It boots up to the tri colour, that's it.

For a moment we will forget about going to 3.14 ROM: I don't know if that phone is entitled to an official upgrade to 3.14, if it is locked to a particular network, if it is branded, etc. If it is not entitled to a 3.14 ROM upgrade then you will have to go through GoldCarding, so we will leave it for now.
Make sure that the battery has had a good couple of hours charge in the charger or double that if connected to the computer.
Remove SIM Card and SD Card.
Switch on to Bootloader Mode, then connect to USB.
Download and run HSPL2 - ignore the instruction about connecting to ActiveSync etc, just proceed.
Download and install the HTC 1.66 WWE ROM - again, ignore the instructions, just proceed.
The reason for HSPL is because your phone may be operator locked (not SIM locked) and you aren't entitled to run the 1.66 WWE ROM.