Hi,
after the download new ROM my MDA was fired!!
First I download a customized ITA rom and after, because the MDA work very slow, I downloaded the latest T-mobile ROM.
Now the MDA do not power up and do not charge the battery.....sems dead.
Can I recover it?
just an idea but I would start by trying to charge it with the wall plug that came with it, not a computer usb cable - if the battery is all the way dead it will not charge from the computer. If the light comes on, let it charge for a while and then try it out. If not I would try to hard reset while it is plugged in. If none of this works, enter bootloader mode and then connect it to the computer, and hopefully it will go into bootloader mode and you can flash a new rom.. If you need more details on how to do any of this, let me know, and please let me know if it works!
Hi....you fine.
I have recharge the battery and dowloaded the original Tmob rom.
Now is strange..
Same time power up...and same time no.
The ipl is 1.06 and spl is 1.03!!
My Qtek 9100 is dead also. I have the 2.24 ROM and it has been running great. I cant power it on and the light doesnt turn on when its plugged in. The battery is definitely not dead. Suggestions? TIA
try this...
try the suggestions listed here
however be warned that any of these will delete any and all data that may or may not still be on your device and restore it to just the fresh ROM...
Hi,
I have flash the rom 1.6 Tmob (IPL 1.06 SPL 1.03) but the MDA restart in loop mode!!
My phone powered up today. It's been sitting on my night stand for a week and it turned on today! Everyday I have tried to turn it on but I haven't had any luck until today...weird!
Related
i was installing new rom on my device.when it was 12%, the computer got locked and i had to reset.Now,my baby did not reflash again.i tried again but himaupragadeutility gave : communication problem. what can i do now? can anyone help me? so a few people know this device, the others even do not know what pda is. what i can do?????????????????????????????
Try putting your device into bootloader mode and making sure your XDA is plugged into the mains as well. There's also an upgrade program which bypasses country id checks.
Good luck.
I got the same problem with my Qtek 2020i today!!!!!
The device is dead and i can't put it into bootloader mode!
I need your help please
Try taking the battery out for about 1 hour. This will run the backup battery down therefore wiping the ram. Put the battery back in, connect it to the mains and put it into bootloader by pressing power, action and reset for about 3-5 seconds until serial appears on screen. No backlight so look carefully.
I tried to remove the battrey for 1 hour but it's still the same!
any way thanks for trying to help pug.
I have a new Prophet (JAMin) and it does not start, even when charged. All that happens is the lights at the top flash, the screen blinks and then no more.
Any ideas, as I need the device later!!!
Does it show any serial number on the bottom of the screen or does it just show a blank screen.
What you could do is remove the battery, SD card out and leave the device like that for about an hour or so. After an hour just insert the battery (not the SD card) and then try charging again. Let it charge for about half n hour and then try switching on the device. Most likely, your device will now wake up, if it doesn't then you will probably need to wait till the amber light turns green indicating a full charge. Try switching on the device again, if still no luck, then you will need to take it down to a service centre.
It works when using power adapter, but not on usb
The prophet does start up when using the power adapter, but not when on the USB. Have left it 'charging', but the charge light is not on.
USB only provides a trickle charge and hence is not the best solution for "waking up" a device. Always make sure that you charge your device through the provided AC adapter. Only in cases of emergency or when synchronisation allow USB charging.
No charge light
No charge light is on. Is that right?
If there is no charge light, that means its not charging to begin with. Can you check if the USB port you are charging from is functional by attaching another device to it. Incase the USB port is fine, try charging from a different USB port; if it still behaves the same way, i suggest you take it down to a service centre. Its quite possible that the charging port on the Prophet is damaged.
sam_sykes said:
I have a new Prophet (JAMin) and it does not start, even when charged. All that happens is the lights at the top flash, the screen blinks and then no more.
Any ideas, as I need the device later!!!
Click to expand...
Click to collapse
Mine used to be like that after I installed spb plus previous version, it wont start at all...I had to switch to a new machine (for free) coz it was only day-2 after i bought the device (nice service btw).
Cheers!
I Have an SPV M600 which when switched on the screen blinks and then powers off, no charging light will only power up with the charger plugged in not with the usb data cable, i used a file called hard_SPL-G4 since then this error occured i think its the software program loader.
I cant reflash via active sync because the device powers off without the AC charger. i do have SD cards, but im unsure how to flash from SD i want my original spl version back and a better OS.
IPL 2.21.0001
SPL 2.21.01ip
GSM 02.69.21
OS 7.7.7.7
I can get to the tricolour screen bootloader with charger plugged please help any advice?
these are the original settings i think
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Once it is in bootloader, can you switch it to the USB cable?
Q: Once it is in bootloader, can you switch it to the USB cable?
A: no it switches the power off when i unplug AC but i can get to the windows OS if i power on with AC..? but flash via activesync no AC on reset.
I do have two SPV M600s im not touching the working one. but would like to fix the other one. SD Flash would help possible corrupt OS or SPL i think?
i can gain access to bootloader but i dont know how to initialize the NBH rom,
i could start the extrom cabs which had an autorun with a list of execution
i updated the rom Mysterious_1.0 all went ok i think
then i ran hard_SPL-G4 i had a lot of errors about sleep4.exe not win32 i think.
i am running x64 pro and upon reset all i had was an occasional screen blink and weak flashing orange and blue led.
ive tried different battery and a different USB to miniUSB. the active sync does take long time looking for changes on OS.
from usb i hold camera button and click reset switch it goes to USB bootloader for a second then off
if theres anyone out there who knows how to reflash the SPL version and a new OS for an SPV M600 english lang from an SD card please link files and explain the process in as much detail please? thankyou!
i did also update the radio version GSM could that be a cause!
The radio version should have nothing to do with it...
I am fairly sure there is something on the wiki about flashing from a storage card, but you need to make the dump of the ROM from the working device, so not much help there...
If you can get into bootloader whilst it is plugged into your computer, it's a very easy problem to fix...
I have decided to find the pinouts for a 4.5V charger (it should be 5V but im not destroying original) and a spare USB-miniUSB attach the power terminals from the charger replacing the miniUSB charge terminals, which should allow me to go to bootloader with USB present. i will post my results in here soon
about accessing bootloader
Hi i have just executed the jump spl files on my problem device and its taken me to a white screen with usb data cable, which i heard is the bootloader really and used tera term pro to dump rom etc. its seems to of hanged at the minute does it take a while to write?
im guessing i could go into the white screen mode and reflash an original orange rom?
New Original OS installed
Hi ive successfully installed a new OS so i presume the white screen is a bootloader. still my problem of powering off upon boot exists, so using this method i want to change the details below
OLD SETTINGS
IPL 2.21.0001
SPL 2.21.01ip
GSM 02.69.21
OS 7.7.7.7
NEW SETTINGS
IPL 2.10.0001 check
SPL 2.21.01ip SPL 2.10.0001 wanted
GSM 02.69.21 GSM 02.07.20 wanted
OS 2.10.1.22 check
Can i reinstall the wanted SPL/GSM from the white screen loader? does anyone know where i can get the files. SPV M600
Repaired 100%
I did it, its fixed charges now from USB data cable. and can enter tricolour bootloader. the problem was something wrong with the spl flash process ive redone that no errors excellent. im happy now
Will a ROM flash now?
Guys I need some help. My Dopod 818 pro died today. I don't know what happened. It wont start or soft reset or even hard reset. Only thing is it keeps blinking, the screen, the power and bluetooth led. anyone can help me here? Thank you.
Bootloader mode
Some update, I'm able to access the bootloader mode while my set is plugged to the mains. Is there anyway I can flash my rom using sd card?
more details...
more details would b helpful. For example, were u flashing the ROM? Or did it just die suddenly on its own?
Try taking the batt out over night.... or perhaps you didn't do your hard reset properly. You're supposed to press the camera & comm manager button and hold them while you poke the reset hole...
Try taking out your SIM card and hard reset.... if all fails, you probably have fried board.
If you are able to access bootloader mode, then you should be able to flash the ROM using a ROM provided by Dopod.
Mains only
Yup my friend tried to flash the rom for me and he messed it up. he flashed the wrong rom. i can't reflash tru usb because i only can get to bootloader when connected to the mains.
Re: Mains only
rattler79 said:
Yup my friend tried to flash the rom for me and he messed it up. he flashed the wrong rom.
Click to expand...
Click to collapse
http://forum.xda-developers.com/viewtopic.php?t=41517
The problem is that i can't turn it on. only on mains
If it died while flashing, then as DILS said, you should be able to reflash it again and again....
Just tried to upgrade my S200 with a 9100 ROM ver 2.8.7.1 WWE (by mistake of course) and I can't turn it on anymore. Somehow it didn't even warn about wrong ROM.
Tried to hardreset it but no luck. When I keep the camera button it goes to RGB only when connected to the charger.
When connected to PC, the red and blue leds keep flashing and my PC gives Error 260 when I try to revert back to the S200 RUU.
Does anyone know how to bring it back to life? Is there a way to boot it from SD card?
-
I-mate Jam
Qtek 9100
Qtek S200
Don't panic!
I did the same thing some time ago!
What you need to do is make sure that the battery is fully charged. (The flashing of the screen can be a result of the flat battery.) Unfortunately, it is not possible to charge the battery when the wrong ROM is installed, as the ROM obviously tells the Prophet how to charge.
Let's assume you have an okay battery.
1) Start the Prophet in Boot mode. This is done by pressing and holding the Camera button and then pressing the soft-reset button. Keep holding for about 7 seconds, and the coloured bands should appear.
2) Connect to PC using the UDB cable.
3) Run the correct ROM upgrade. You do not need to be paired with ActiveSync, as the update programs are intelligent.
4) If the update does not work (and it fails at 95%), then try again. If it still fails, try again and do a soft-reset mid-way through. This will kill the ROM upgrade and you should then be able to do it fine after that.
The really important thing is that the battery is charged before you do this. Unless anyone makes a USB cable that can charge AND connect to PC, then a fully charged battery is a must.
Let me know if this helped.
Check this Out
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!
Check this Out
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!
Re: Boot from SD?
zealerc said:
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!
Click to expand...
Click to collapse
I am a bit confused, does that mean that ALLOW USB CONNECTIONS has to be chacked or unchecked?
I did the same exact mistake. Now, my baterry is fully chaged (which I can check on another phone) but when I put it in S200 it shows that the battery has 0%. Conseqeuntly, when i unplug the power cord the phone dies. I have no way of running the new ROM on it. I tried running a bootable SD but it only installed part of the software. i read on this forum that such a thing happens and that one would need to run a full version ROM from a computer. So, how do I do it??? I am almost giving up all hope of ever making this phone work
Does anyone have a file to boot from SD and is it possible to run a full ROM from SD. Please help!
Hi There.
I really need your guys help!!!
a few weeks ago, i lost my battery and i recharged it using USB cable and battery.
It was boot up and i was testing it and keep reboot up. It was work!!
But after a hour left, can not boot up again.
I recharged my battery using USB cable ( cut it off and using red and black wire)
I did hard reset. ( Still not work)
try to flash rom, but can not do it. I was in Bootloder and when i attached USB cable to my kjam, it show off that USB on the screen with 3 colors.
I tried all the way, but still can not boot up.
My PDA show blue screen with I-Mate and
IPL 2.16.0001
SPL 2.16.0001
GSM 02.20.11
OS 2.16.9.1
Please guys help me to boot up my Kjam.
Please.
[email protected]
I tried restore ROM, but still can not boot up.
Please guys help me. T.T