Related
I have a new Prophet (JAMin) and it does not start, even when charged. All that happens is the lights at the top flash, the screen blinks and then no more.
Any ideas, as I need the device later!!!
Does it show any serial number on the bottom of the screen or does it just show a blank screen.
What you could do is remove the battery, SD card out and leave the device like that for about an hour or so. After an hour just insert the battery (not the SD card) and then try charging again. Let it charge for about half n hour and then try switching on the device. Most likely, your device will now wake up, if it doesn't then you will probably need to wait till the amber light turns green indicating a full charge. Try switching on the device again, if still no luck, then you will need to take it down to a service centre.
It works when using power adapter, but not on usb
The prophet does start up when using the power adapter, but not when on the USB. Have left it 'charging', but the charge light is not on.
USB only provides a trickle charge and hence is not the best solution for "waking up" a device. Always make sure that you charge your device through the provided AC adapter. Only in cases of emergency or when synchronisation allow USB charging.
No charge light
No charge light is on. Is that right?
If there is no charge light, that means its not charging to begin with. Can you check if the USB port you are charging from is functional by attaching another device to it. Incase the USB port is fine, try charging from a different USB port; if it still behaves the same way, i suggest you take it down to a service centre. Its quite possible that the charging port on the Prophet is damaged.
sam_sykes said:
I have a new Prophet (JAMin) and it does not start, even when charged. All that happens is the lights at the top flash, the screen blinks and then no more.
Any ideas, as I need the device later!!!
Click to expand...
Click to collapse
Mine used to be like that after I installed spb plus previous version, it wont start at all...I had to switch to a new machine (for free) coz it was only day-2 after i bought the device (nice service btw).
Cheers!
I Have an SPV M600 which when switched on the screen blinks and then powers off, no charging light will only power up with the charger plugged in not with the usb data cable, i used a file called hard_SPL-G4 since then this error occured i think its the software program loader.
I cant reflash via active sync because the device powers off without the AC charger. i do have SD cards, but im unsure how to flash from SD i want my original spl version back and a better OS.
IPL 2.21.0001
SPL 2.21.01ip
GSM 02.69.21
OS 7.7.7.7
I can get to the tricolour screen bootloader with charger plugged please help any advice?
these are the original settings i think
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Once it is in bootloader, can you switch it to the USB cable?
Q: Once it is in bootloader, can you switch it to the USB cable?
A: no it switches the power off when i unplug AC but i can get to the windows OS if i power on with AC..? but flash via activesync no AC on reset.
I do have two SPV M600s im not touching the working one. but would like to fix the other one. SD Flash would help possible corrupt OS or SPL i think?
i can gain access to bootloader but i dont know how to initialize the NBH rom,
i could start the extrom cabs which had an autorun with a list of execution
i updated the rom Mysterious_1.0 all went ok i think
then i ran hard_SPL-G4 i had a lot of errors about sleep4.exe not win32 i think.
i am running x64 pro and upon reset all i had was an occasional screen blink and weak flashing orange and blue led.
ive tried different battery and a different USB to miniUSB. the active sync does take long time looking for changes on OS.
from usb i hold camera button and click reset switch it goes to USB bootloader for a second then off
if theres anyone out there who knows how to reflash the SPL version and a new OS for an SPV M600 english lang from an SD card please link files and explain the process in as much detail please? thankyou!
i did also update the radio version GSM could that be a cause!
The radio version should have nothing to do with it...
I am fairly sure there is something on the wiki about flashing from a storage card, but you need to make the dump of the ROM from the working device, so not much help there...
If you can get into bootloader whilst it is plugged into your computer, it's a very easy problem to fix...
I have decided to find the pinouts for a 4.5V charger (it should be 5V but im not destroying original) and a spare USB-miniUSB attach the power terminals from the charger replacing the miniUSB charge terminals, which should allow me to go to bootloader with USB present. i will post my results in here soon
about accessing bootloader
Hi i have just executed the jump spl files on my problem device and its taken me to a white screen with usb data cable, which i heard is the bootloader really and used tera term pro to dump rom etc. its seems to of hanged at the minute does it take a while to write?
im guessing i could go into the white screen mode and reflash an original orange rom?
New Original OS installed
Hi ive successfully installed a new OS so i presume the white screen is a bootloader. still my problem of powering off upon boot exists, so using this method i want to change the details below
OLD SETTINGS
IPL 2.21.0001
SPL 2.21.01ip
GSM 02.69.21
OS 7.7.7.7
NEW SETTINGS
IPL 2.10.0001 check
SPL 2.21.01ip SPL 2.10.0001 wanted
GSM 02.69.21 GSM 02.07.20 wanted
OS 2.10.1.22 check
Can i reinstall the wanted SPL/GSM from the white screen loader? does anyone know where i can get the files. SPV M600
Repaired 100%
I did it, its fixed charges now from USB data cable. and can enter tricolour bootloader. the problem was something wrong with the spl flash process ive redone that no errors excellent. im happy now
Will a ROM flash now?
Hi,
after the download new ROM my MDA was fired!!
First I download a customized ITA rom and after, because the MDA work very slow, I downloaded the latest T-mobile ROM.
Now the MDA do not power up and do not charge the battery.....sems dead.
Can I recover it?
just an idea but I would start by trying to charge it with the wall plug that came with it, not a computer usb cable - if the battery is all the way dead it will not charge from the computer. If the light comes on, let it charge for a while and then try it out. If not I would try to hard reset while it is plugged in. If none of this works, enter bootloader mode and then connect it to the computer, and hopefully it will go into bootloader mode and you can flash a new rom.. If you need more details on how to do any of this, let me know, and please let me know if it works!
Hi....you fine.
I have recharge the battery and dowloaded the original Tmob rom.
Now is strange..
Same time power up...and same time no.
The ipl is 1.06 and spl is 1.03!!
My Qtek 9100 is dead also. I have the 2.24 ROM and it has been running great. I cant power it on and the light doesnt turn on when its plugged in. The battery is definitely not dead. Suggestions? TIA
try this...
try the suggestions listed here
however be warned that any of these will delete any and all data that may or may not still be on your device and restore it to just the fresh ROM...
Hi,
I have flash the rom 1.6 Tmob (IPL 1.06 SPL 1.03) but the MDA restart in loop mode!!
My phone powered up today. It's been sitting on my night stand for a week and it turned on today! Everyday I have tried to turn it on but I haven't had any luck until today...weird!
Hello,
i tried to update my BA with wm6.
after flashing it stuck in bootloader(blue,green,red,white display) with the line "R 1.10.00" and nothing more...
even hard or softreset do nothing.
what can i do?
ok i even try the Stuck at startup method.
that's the output of Multiport TTY Version:
set 14 0
HTCST ÚÈÒHTCEUSB>task 28
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=2BA0000
All:dwSize=3C20000
USB>task 0
it always stuck in blue,green,red,white screen after run multiport tool. what can i do?
------------
i have this problem because of this flashing method:
i entered the grey screen (with serial/usb in first line). then i put my usb connection on and run the rom_update. after it is finished (succesfully) it stuck in the blue, green, red, yello screen! help please...
how did you hard reset?
hello,
i hold down the power-button and at same time put stylis in reset.
hard reset for both WM5 and WM6 is different from the one you're doing. here's the guide...
http://wiki.xda-developers.com/index.php?pagename=BlueAngel_WM5_For_Beginners
good luck!
ok thanks, i have tried this:
i do softreset. whenn the stripes came i push "records and "camera"(media player button because there is no camera)---> nothing happens. it stops with the line R 1.10.00 and the coloured stripes.
i dont knwo what to do.
the bootloader method is running. i hold power and record button while i softreset. but with color screen it wont work.
they is no camera button (it is media-player button) because there is no camera. its an german xda III (blue angel).
the next problem is i dont knwo what os is right now on it. befor flashing it was wm2003 and flashing says it was successfully. i dont know if its wm6 or wm2003!
ok now all is happen...
the xda says nothing. it dont go on, it dont work anymore. no lights when in cradle, nothing.
can i do anything?
1. Take the battery out, wait a moment, put it back, do not turn on. Put in the cradle and try to charge it. Use power connection (from power supply), disconnect USB from the computer for charging. Amber led should turn on.
2. When it will be fully charged (amber LED will turn off) try to turn it on and enter bootloader. Try to downgrade to WM2003. If it works fine, try again to flash WM5 or WM6.
What you did seems to be wrong update (wrong rom, wrong file, not fully flashed). But you still have bootloader, so it should be possbile to flash it. But you need full battery.
jakubd said:
What you did seems to be wrong update (wrong rom, wrong file, not fully flashed). But you still have bootloader, so it should be possbile to flash it. But you need full battery.
Click to expand...
Click to collapse
it was not unlocked befor i flashed with bootloader-method.
i charged the battery in cradle (withoud the blue-angel). the led first went orange, after a while turned green (fully loaded). put it back in BA an nothing happens. then put BA (with battery) in cradle and the led became red.
no action on devide, no feedback, nothing. it wont turn on but led is still working.!?
jakubd said:
2. When it will be fully charged (amber LED will turn off) try to turn it on and enter bootloader. Try to downgrade to WM2003. If it works fine, try again to flash WM5 or WM6.
Click to expand...
Click to collapse
ok i get it. in display is the "USB" & "v2.07". now i can flash. but my problem is the phone is not unlocked yet. what file can i flash now??
This message tells you are in bootloader mode. Now you can perform normal flash - I would propose you to use tested&working rom (WM2003?). If this works fine, try again to upgrade to WM5/WM6.
BTW: if you disconnect USB (take out BA from cradle) it should show Serial instead of USB.
ok big tanks to the forum. i finally get it. wm6 german on blue-angel!
Same thing here... but worst..
My 9090 is stuck at bootlader...
When i try to update, (i press the power, record and reset), it says:
SERIAL (or USB)
DOC VERSION IS ERROR!
v2.08
Any idea???
that's normal...
try to flash/update your BA in that screen.
the easy way to go into bootloader mode is to execute a file called Enter Bootloader.exe ..it comes with the rom u download..( well it came with xplodes )
Note:- you have to execute this file directly on your deive not on your desktop PC...and i have only tested this on WM 2003..maybe it will work with wm6 also
SilverSamurai said:
that's normal...
try to flash/update your BA in that screen.
Click to expand...
Click to collapse
I there...
I just updated to BA_TMNL_14200_119_11300_Ship, but only with Maupgrade, couldnt do it with baupgrade...
The problem is that i cant put extended rom, whem i try to upgrade is allways an error... and in the settings i dont have extended rom instaled...
Besides that the batery only last 1hour and the PDA is always freezing... i'm always doing resets...
any idea??
Sorry for my bad english by the way...
hello
I bought 2 magicans but one works fine the other wont torn on. But wen I conectet it on a charger it has started to boot, but for a few seconds then shotdown. I tryed hard reset and everything I could imagenen. When is conected to pc whit a usb cabel it dosent turn on.
ps:
I am sorry for my english.
thank you all
hello
I bought 2 magicans but one works fine the other wont torn on. But wen I conectet it on a charger it has started to boot, but for a few seconds then shotdown. I tryed hard reset and everything I could imagenen. When is conected to pc whit a usb cabel it dosent turn on.
ps:
I am sorry for my english.
thank you all
Problem in Rom
Hi
According to my understanding, your rom is not working properly. Please download the fresh copy of WE_2.03 Rom and 1.3 Radio. Than attach your cell with your pc. Press soft reste button+camra button+long press reset button. This will tour your cell to usb mod (total black) than install 1.3 radio and after that, install 2.03 rom. In this way you can replace your old rom with brand new one. There is a lot of information on the bellow link how to replace your Rom
http://forum.xda-developers.com/showthread.php?t=322110
Ali
thanke you ali
Thank you ali but the problem is that I can not enter the boot mode (usb mode). The problem is theat only on chrger the phone starts to boot. It wont boot when plugd in pc wia usb or on on batt power.
thanks
Hi Guys...
I'm trying to cook a rom... but now I'm ...
MY PHONE is BOOTING and BOOTING and BOOTING, I connect the USB CABLE and then the phones turns ON and HTC screen apears then He reboot Again... and again and again...
I already try to flash the Stock Rom and Had the same problem...
Did you Hard SPL it? Also if you from turned off, Hold Volume Down and Power, does it boot into the tri color mode? If so you can get the image file and follow these steps here
http://forum.xda-developers.com/showthread.php?t=691779
To bring you back to square one, then hard spl it correctly and load your rom, I prefer energy, see my sig for that link.
Maybe you should enter the bootloader? try and flash a cooked rom or stock rom to see if it still works
I Already do that... but still the same...
I thinking that is batery down... when I unplugged the USB cable the phone deads...
I had another battery in work, tomorrow I will see,,, because e don't charge...
He Won't Pass HTC blank screen when and turn ON... e reboot and reboot and reboot...
EDIT: Already Find The Problem ... A Pin in Batery connecte was wrong...