Stuck at Start up Screen - MDA III, XDA III, PDA2k, 9090 ROM Development

I upgraded my SX66 to WM6 and it worked fine for about 6 weeks, then it froze so I reset it and now it hangs up on the Windows Mobile Splash screen. I've tried hard resets, reflashing the ROM, and reflashing the radio stack but nothing helps. The versions I have currently loaded are R - 1.15.00
G-1337.45 and D- 5.60.00. I also tried reflashing with xplode's version 6 but then it hangs on the 4 striped screen. If anyone has any ideas please help, I'm lost without it.

hello,
try reading my thread
http://forum.xda-developers.com/showthread.php?t=352399
i was stuck there too and i did a hard reset.
remember to change the 2 options and push the mail button!
best of luck
jason

IT WORKS!!!
Thank you, thank you, thank you. I had tried that but didn't know I was supposed to push the mail button to save it. My PDA is no longer a brick! Thanks again.

Related

help. backlight is no longer working with kitchen 4.00.05

hi
i am no longer able to turn on the backlight after upgrading to 4.00.05 from 4.00.01. I can only see it flashing quickly on a soft reset - so i know it still works. but holding the power button wont do anything. any ideas?
woody
... running a german mda pw10a2 with radio 4.21
I too had this problem when I tried a restore from my backed up 4.00.01 version (I was being lazy and didn't want to reinstall all of my applications). A hard reset and manually reinstalling the applications solved the problem for me.
hey, this is just what i did... wanted to cut corners .
i just did a hard reset and everything is fine now.
thank you so much for the quick response!
Glad to have been of help.

Updating Exec ROM - I'm so screwed, please help

Hi guys,
I just tried to upgrade to the latest o2 Exec ROM, followed all the instructions to the letter ... then the dialog box that says "getting device information.... don't unplug, bla bla" came up and stayed the same for over 70 minutes and decided something isn't right, so I unplugged it.
Now, my exec only shows "USB v1.00" screen ... can't turn it off, and hard reset can't restore anything. It appears my ROM has already been zapped clean ? ...
Arrrggghh, this is driving me nuts. If anyone can tell me how I can get things back to normal, I would be eternally grateful
Chris
the same happened to me.
Connect the usb cable again and try running the setup wizard again.
1) Disconnect your Universal from the cable.
2) Perform a hard reset by pressing the 2 (-) buttons simultaneously while pressing the reset pin found at the back of the Universal.
3) You will notice that the screen is still blank with the "v 1.0" on the screen. DO NOT WORRY.
4) Connect back your Universal via cable.
5) You will hear the connection sound from your computer.
6) Run the install application again.
7) Make sure you DO NOT DISCONNECT the cable this time.
8) RELAX!!!!!! and wait for the update.
I had same problem but this is what I did
1) Hard Reset
This screen pops up
Press0 to restore
Factory default
Press X to exit
2) I pressed X
3) Plugged in USB cable
4) Voila, windows recognises new device, when driver is installed pressed X
ran software utility (rom upgrade) again
All is working, Panic over PHEW!
Phheewwww ... thanks so much you guys, really appreciate all the detailed instructions ... it's upgrading as i post this ... for a moment there, i thought i would have to ship this back to o2 ... He hee ... you guys are the greatest ! :lol:
So guys now that you all have upgraded your universals, is it worth the update ?
I've been running my current one in Basic Mode since getting it and have not experienced any problems yet.
i works better,it responds quicker and no crashes yet. the themes fit according to the screen. try it.
fince120 said:
i works better,it responds quicker and no crashes yet. the themes fit according to the screen. try it.
Click to expand...
Click to collapse
Which themes?
screen switching is like lightning, definately an improvement.
Overall Id say it seems quicker loading menus
(eg start>programs, Start>settings etc)
I think it was worth it although i shat myself when the upgrade went wrong.
Tut Tut o2, wtf was that all about?
hi guys, i have follow the instruction, and it is not working for me.. any others ideas
thanks
My Method:
1) Connect your Universal from the cable. (Whole step not need disconnect the cable)
2) Perform a hard reset by pressing the 2 (-) buttons simultaneously while pressing the reset pin found at the back of the Universal.
3)This screen pops up
Press0 to restore
Factory default
Press X to exit
4) I pressed 0
5) You will notice that the screen is still blank with the "v 1.0" on the screen. DO NOT WORRY. Wait about 15 seconds!
6) You will hear the connection sound from your computer. (If it appare a wrong connect device message on computer, then retry from step 2 to step 4. This step my need to try many times until hear the connection sound from your computer) [Some times I had repeated three steps twenty times then can success!]
6) Run the install application again.
7) Finish & Reset.
i have done, the step. Due to frustration i have remove the active sync and install a new one. might be this step will no longer use.
thanks any way. is there any other suggestion?..
upgrade completed but still screwed
After trying for almost 24 hrs.I finally got it upgraded and completed with CONGRATULATIONS ....BUT
on soft reset(pushing the reset hole) it returns back to the bootloader screen. I tried 5 times with the same result and I then tried Hard reset and the screen is still at bootloader.
How to BOOT it to TODAY screen??????
Pls help..
Re: upgrade completed but still screwed
leslie lee said:
After trying for almost 24 hrs.I finally got it upgraded and completed with CONGRATULATIONS ....BUT
on soft reset(pushing the reset hole) it returns back to the bootloader screen. I tried 5 times with the same result and I then tried Hard reset and the screen is still at bootloader.
How to BOOT it to TODAY screen??????
Pls help..
Click to expand...
Click to collapse
see your pm
thanks a million Mwang.
I shall reflash again n shall keep my fingers cross that upon completion of flashing I can reset and get to configure the dopod....on hopefully the new rom113.82
thanks n appreciated
leslie lee said:
thanks a million Mwang.
I shall reflash again n shall keep my fingers cross that upon completion of flashing I can reset and get to configure the dopod....on hopefully the new rom113.82
thanks n appreciated
Click to expand...
Click to collapse
Ihave completed flashing the xda rom 113.118 using the MaUpgradeUt noID a 2nd time. I reset my dopod900 and it reverts to bootloader screen ie top..serial bottom...v1.00
Idid the reset another 5 times with the same result
I tried the on/off buttom-no result...still at the bootloader screen..
I am now reflashing for the 3rd time....
any helpful advise would be very much appreciated...with thanks
leslie lee said:
leslie lee said:
thanks a million Mwang.
I shall reflash again n shall keep my fingers cross that upon completion of flashing I can reset and get to configure the dopod....on hopefully the new rom113.82
thanks n appreciated
Click to expand...
Click to collapse
Ihave completed flashing the xda rom 113.118 using the MaUpgradeUt noID a 2nd time. I reset my dopod900 and it reverts to bootloader screen ie top..serial bottom...v1.00
Idid the reset another 5 times with the same result
I tried the on/off buttom-no result...still at the bootloader screen..
I am now reflashing for the 3rd time....
any helpful advise would be very much appreciated...with thanks
Click to expand...
Click to collapse
Flashing ok for 3rd time also using MaUpgradeUt noID...
I must convey my sincere thanks to u Sirius n Mwang,argh for trying to help.
After the flashing finished I took the dopod off the mini usb cable n reset...reverts to bootloader mode.
tried cold boot ie..on/off button n reset same time..same result
tried hard reset...same result ie back to bootloader screen
am now flashing it for the 4th time(tried not to used MaUpgradeUt noId but come out with ERROR 120 n cannot even flash)
what shall I do?????
leslie lee said:
I am now reflashing for the 3rd time....
any helpful advise would be very much appreciated...with thanks
Click to expand...
Click to collapse
Download the uni dopod rom upgrade from the xda server. Extract the executable file. Then flash ONLY the radio rom using the MAUpgradeUt. Do not use the other rom files (e.g. extended and MS rom, so delete these two before running the MAUpgradeUT.) good luck.
simba said:
leslie lee said:
I am now reflashing for the 3rd time....
any helpful advise would be very much appreciated...with thanks
Click to expand...
Click to collapse
Download the uni dopod rom upgrade from the xda server. Extract the executable file. Then flash ONLY the radio rom using the MAUpgradeUt. Do not use the other rom files (e.g. extended and MS rom, so delete these two before running the MAUpgradeUT.) good luck.
Click to expand...
Click to collapse
Thank u Simba
I shall try your suggestions and wish me luck for xmas
many thanks n very much appreciated..
thank u simba
New year is on d way....
BINGO..... yes I made it...
as simba suggested I download the UNI DOPOD rom113.36..extract the executable files ie.
!. Enter BL
2.GetDeviceData
3.RUU.dll
4.UI.dll
5.RUU.Conf
6.MaUpgradeUt noID
into a new folder ..add in the radio file from either rom113.188 or 113.36
and then execute/run MaUpgradeUt noID file......IT WORKS
It therefore may means that DOPOD900 may require the DOPOD EXECUTABLE FILES (so as not to have the same problems as I had over xmas) listed above to upgrade either the CE rom, radio rom or extended rom..
It definitely had been a very interesting xmas...the freeze is finally over n a Better time awaiting, better days ahead n a better YEAR is around d corner...Happy New Year to everyone

Help Please

Hi have a slight issue with my Mini s, i believe its the wizard. When i go to send txt messages it tells me the phone is not ready and i have to wait 15 seconds, so i cant send msgs, i can still ring in and out, also when i try to go to phone settings it tells me to wait 15 seconds and try again, when i go to sim manager it tells me to again, wait! I believe at the moment it is flashed to 02 with an orange sim in it, its the G4? version. Its running wm5 i think, if i could have it flashed to orange on wm6 that would be great.
Any help on how i can overcome this problem would be great. Thanks
Matt
Perform Soft Reset first,check if it solves the problem, or Hard Reset,but remember you'l llose all your personal data by doing hard reset,but it might solve the problem.If nothing works,than its corruption of the extended_rom,you might have to reflash a rom.
To upgrade to wm6 read the guide posted here at xda-wiki ,be careful,if you say its a G4 device,its a bit sensitive device:-
http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
rite ok ive already tried a soft reset but it didnt work, sorry i havent got a manual for the phone so how do i do the hard reset? also if so how do i reflash the rom, any guidance would greatly be appreciative.
Thanks
Hard Reset
Hardreset for Wizard is by pressing: Comm button + Voice command button and slightly push the softreset button with stylus.
Guide to flash a rom is posted in my above post.
you should reflash your rom I also has same issue and reflashing solved the problem.

HELP, stuck at bootloader screen

I urgently need help with my BA
I attempted to upgrade to Beta version:WM6.1 CEOS 20262.Build 19949 Aku1.2
by sun dream and now its stuck in the bootloader screen, I have gone through the wiki of BA and have done various suggestions on how to hard reset my device but nothing seems to be working. Any help extended will greatly be appreciated. Thanks and More Power to all you guys!
Flash again. If no progress - flash different ROM. Never forget about proper HR after each flash.
hey out there,
i do have some problems with my Blue Angel the last days, i flashed a new rom
1.15.00
1337.45
V.6.01.09 DVH
and had Problems with active sync, seemed like it didn't get an Ip adress.
so i flashed sunwell 6.1 and i was able to synch but radio rom was missing and i wasn't able to do calls at all. Hard/soft resetted reflashed flashed other roms, but now i stuck directly after the Bootloader screen when showing windows mobile 6 logo.
It makes an annoying "Bling" and it's reacting on commands, Stylus or Power button, but i didn't finish starting even after 10 min. I flashed some other roms.
same problem. any suggestions?
sorry for abusing this thread but i didn't wanted to start a new "wuhuhuhuhu i bricked my friends BA" thread.
thanks florian
edit.
if starting now it shows Radio and GSM None
hm...formatted with mtty restarted
put sim inside.
displaying R,G NONE when booting.
soft resetted, displayed right data.
Booted, finally working whyever.

Wizard boot up then goes to white screen

Hi XDAers,
I have tried a number of things and is at a loss - I have a 2 years IMAT KJAM Wizard G4. The problem occured 2 days ago when the device just freezed on me. I did a soft reset, booted fine but then came up after the initial load screen (WizardLove AKU 2) with a white screen.
I have reloaded the IPL, flashed the ROM with WizardLove again, Hard reset back to factory defaults, soft resets the works.
After ROM flash it boots up, i get ActiveSync to load and connect fine. but with in 5 - 10 after having the phone up and working the screen goes white.
If any one has any idea what could up with the Wizard device please let me know?
Regards,
Hennie
I have the same problem!
Not sure how hard it is to fix but it seems to be a component issue,
Iknow its a different phone but check out:
http://forum.xda-developers.com/showthread.php?t=303872
I havent tried it yet but it worked for them

Categories

Resources