connecting my XDA to a different router - JASJAR, XDA Exec, MDA Pro General

connecting my XDA to a different router - JASJAR, XDA Exec, MDA Pro General

Hello,
I have got two wireless routers at home and my XDA Exec is connected to wireless router A.
i am trying to change the settings on my xda so that it connects to wireless router B, but i cant find the place where i can change the settings,
can you guys help me.

hi
i have managed to find out how to delete items from the list, by pushing hard on the stylus, i get the option of removing from the list.
I can't connect to the network which i want to connect to, originally i had it connect to my network "BTHome-hub" with no problem, and i wanted it to connect to my netgear router which is an unencrypted network, not connected to the internet.
to force it to reject the BTHome_hub, i changed the WEP key(yes, i am a noobie), so that i could get the next network, and then i started getting this problem of the xda showing all the devices in the neigbourhood as available (and some old devices which is shows as unavailable), and it runs through each of those available devices, trying to connect to each of them, and it fails to do that.
i have gone through a number of the posts on the forums. and have tried the following.
1. change Power Mode to Best Performance !! in my Wifi Settings.
2. i had no mac filtering on any of my routers, and have turned on mac router on one of the routers and added the mac address of my xda
3. i tried the following start-settings-connections-network cards-my network card connects work and rest to internet, this time around i was prompted for a password, whereas neither does my router have a password and the authentications i open and data encryption is disabled
(does connects to (in configure wireless network) the internet/work make any difference?
if one of the routers has a strongers signal than the other, would the xda wireless get confused and try to connect to the router with the stronger signal?
i was thinking that channel 11(on which i am) is quite busy and hence i changed the channel to channel 1, do i need to make the channel modiiications on the xda as well
what does the soft reset rest?

a) soft reset is like turning your desktop/laptop computer off and then on again. hard reset is like reinstalling the operating system on your pc.
b) if one router has such a bad signal that the universal loses the connection, the uni will look for another router. it will ask you which new one to connect to unless it already has settings for a new one.
c) if you're getting interference problems, set the router to channel 13. it's europe-legal only so american routers don't usually use it. your clients (pc's and your universal) will scan for the right channel.
d) at the pc shop where i work, we get LOTS of problems with BT Home Hubs' wifi - so don't think it's your fault, it probably isn't.

Related

XDA2ii can't connect to WIFI at home

Hi!
Before I start tese are my current system info:
XDA2ii (O2) - UK
ROM version 1.10.00 WWE
ROM date:24/12/2004
Radio ver: 1.00.00
Protocol version: 1337.39
ExtROM version: 1.10.124 WWE
OS: Windows Mobile 2003 2nd Edition
Version 4.21.1088 (build 14235.2.0.0)
I am trying to connect to my home WIFI network but I can't seem to connect. It is indeed picking up the server (name appears) in list but just stops at connection to network. It can't seem to get any connection at all. My wireless router (Linksys WRT54G) can't seem to detect it as well.
I have tried connection to WIFI at an airport and it seems to work but not at home. I have set my Linksys to Mixed mode (B and G) but still can't get it to work.
Any advice?
Thank you!!!

XDA IIi (or 2i) and 3COM WAP
Hi.
Got the exact same (everything) XDA IIi model (also O2/UK). I'm also having problems with WLAN/WIFI connectivity both at work and home. Both cases it's a 3COM OfficeConnect WAP (office one not setup by me). I thought I validated that the XDA seems to be OK by being able to connect to a neighbours WAP (some BT-Voyager thing) with no apparent problems. And so was thinking that the problem is with the 3COM WAP. However, your post raises doubts on my conclusion ...
The search goes on ...

Re: XDA IIi (or 2i) and 3COM WAP
hi
My case is even worse, it can not detect any wifi signal at any of the hotspot in my city. Go to wireless Lan Manager, under WLAN button (red status) there is alwayls a sentence: "no connection in use". Clicking to it, the device seem to search but found nothing.
Try softreset, hardreset but the problem remains.
In addition, I try to turn off the phone (turn on flight mode) then it don't allow to turn on bluetooth and wifi too.
Maybe it is due to hardware error.
Really disappoint with O2 UK
Regards
Tuan

WiFi connection problems with XDA2i
I have exactly the same O2 xda2i build as Johnnyboy, and precisely the same problem with WiFi as Blackwolf and Johnnyboy. I have a netgear WiFi access point at home, and have disabled the attach restriction and removed WEP. However, although the XDA can see the network name, it cannot connect to the network (just displays connecting...) nor does it show anything on the signal bar. Needless to say, it does not display SSID, Tx rate, Channel, IP address or any information from the network.
I have bought this device specifically for wifi access, and it is somewhat disappointing. Anyone have any idea how this can be fixed? (if at all :? )

XDA Wi-Fi Successful Connection!!!
Hi,
I'm new to the forum and new to XDA2i....
I too had many frustrations connecting the wi-fi...but now I've cracked it, here's how.......
On first very first use (or following a hard re-set) device users are prompted to choose “What do you want WLAN to connect to?” The option bullets are ‘Internet’ or ‘Work’….’Work’ should be selected, this will connect them to the nearest WLAN (if this network is WEP encrypted it should be switched to ‘Open’ rather than ‘shared’ as is often the case).
Next prompt asks for any WEP Encryption ‘Pass Key’ to be input, when doing so omit any ‘-‘ between character pairs. Normal start-up should then be completed. Once device is up and running…..
From ‘Start’ pull-down on the ‘Today Screen’ select…. ‘settings’>’connections tab’>’connections icon’>’advanced tab’>’Select Networks’> pull-down ‘My Work Network’ > ‘OK’ out of selections to save and exit.
Go to ‘Wireless Manager’ in programs, select WLAN icon from main screen (which should turn green to show active), then select mini ‘WLAN’ icon from lower toolbar to see the status of the connection, quality of signal etc.
That did it for me......
Cheers

Finally cracked it! As I never had any problems with my Netgear MR814 wireless router, I assumed the issue was with the XDA2i. Instead, a router firmware upgrade did the trick! Should have thought of that earlier.
Cheers, S.

When i first got my XDA 2i home from the shop the first thing it tried was the wireless lan, and the same thing happend to me also..... everything fine in the router but still unable to connect the xda.
anyway after few hours of going over every single setting time and time again , it finally worked !!
i left the Wlan enabled and after a period of a few minutes it connected to my network.
So i think the XDA 2i is quite tempremental with Wlan, as i know my settings were correct.
having said that, i have had no problems with Wlan t all since then, it will now even connect to other Wlan hotspots with no problems whatsoever.
The only problem i have now is recieving a decent O2 Cellphone signal i my area

Well I have a XDA IIi and it connects fine and allways has to Citi Hotspots, TMO hotspots and my own Linksys WRT54GS. Netgear is the biggest piece of crap ever sold. If you have one I suggest you soak it in gas and burn it.

I had a problem with my XDA IIi connecting to a home Wi-Fi network with a Linksys WRT54GC router: a signal showed in the Wireless LAN Manager, including an IP address, but the WI-Fi icon at the top of the Today screen had no connection bars. After days of this I went to the Linksys settings for an unrelated reason and disabled Wireless SSID Broadcast. Inexplicably this appeared to cure the WiFi problem with the XDA IIi, and I can now connect with ease.

Ok, I might as well add my question to this thread, as it's relevant.
I have an O2 UK XDA2i, and I've also experienced similar problems connecting the wifi and managing to get it to work properly.
I'm at Uni in Birmingham, and at some of my faculties there's wifi for students and staff to use - they give the broadcast SSID UCEOpenAccess, and you use your system logon (in my case STUDENTS\F05310011 and my password (secret ).
I have these details set in the LEAP tab of my wireless lan config (in the WLAN settings) - I have an entry named UCEOpenAccess, and I have my username and password (and domain) set correctly, and the auth type set to Open System (as opposed to EAP, doesn't seem to make any difference whatever I set it to)...
... I just can't connect to any wifi network! I can't even _SEE_ the wifi network, and I know it's there, I can pick up other wifi networks and detect them using Wifi Graph and Hitchiker. I just, bizarrely, can't see the one wifi network I'm trying to connect to.
It's incredibly frustrating. I have my network adapter set to connect to Work (as I've seen advised on these forums), and my IP is assigned via DHCP (they use a weird class b subnet for their network), and the proxy to connect to the Internet is also setup correctly in my Network (This network connects to the Internet checked, This network uses a proxy to connect to the Internet, and proxy is specified in the box), and as the proxy is a SOCKS 5 authenticating proxy, all the relevant details and username+password are in place in the Advanced settings.
Still doesn't work!
Is it due to my original (and decrepit, from the looks of things) firmware and software versions? I'm running original radio, is that a problem maybe? I've scouted about quickly for updates from O2 for my XDA, but I don't want to install a Japanese update as I don't reallllly want to have to read Japanese (and I can't, etc) - I don't want to make a brick out of this brand new phone, but the resources for total xda newbs is somewhat lacking. Can someone just poke me in the right direction with a stick?
Cheers all.

HTC Touch WiFi Problem

Hi All,
I too have a strange WiFi issue. Here goes:
My phone is able to connect to free WiFi stations and the WiFi station at my parent's place. When I try to connect at home, it connects but I am unable to browse.
I previously used WEP encryption and have also tried removing all encryption...but no luck.
Here are my current router settings:
Band 2.4 GHz B+G
Mode AP
Channel 9
Authentication Open
Preamble type Long
Broadcast SSID Disable
Encryption None
Use 802.1x Authentication Disabled
Phone Details
HTC Touch
Browser Netfront/IE
My laptops, DS Lite, Wii can connect and work with the router...
Any help will be highly appreciated

Check that you don't have MAC ADDRESS FILTERING at the router. It may be hidden under Filter settings, like my D-Link is. This may sound trivial, but more than once I forgot about the MAC filtering.
If that doesn't help you, then just to narrow it down, at my home I use WEP and disable SSID broadcast also, and my Touch can connect fine, and fast.

Scratch the last post! I had the same problem with my TOUCH..Just put the power level to the max (i.e. go Start -> Settings -> Connections -> Wireless LAN -> Power Mode -> and slide all the way LEFT to Best Performance) and all hail ..your problem solved

I also use a Touch. I put the slider all the way to the right (Best Battery) and I connect fine. You people must have a big house, or a crap router?

HTC Touch wireless lan connection problems
hi,
Im having the same problem. No MAC filtering & no encryption on ADSL router.
HTC touch can connect to the router at 192.168.1.1. But it does not connect to any other web page.
Message shown is: "Page cannot be found. Check the name and try again."
Any other tips.
Thanks in advance.
dbmayur said:
Hi All,
I too have a strange WiFi issue. Here goes:
My phone is able to connect to free WiFi stations and the WiFi station at my parent's place. When I try to connect at home, it connects but I am unable to browse.
I previously used WEP encryption and have also tried removing all encryption...but no luck.
Here are my current router settings:
Band 2.4 GHz B+G
Mode AP
Channel 9
Authentication Open
Preamble type Long
Broadcast SSID Disable
Encryption None
Use 802.1x Authentication Disabled
Phone Details
HTC Touch
Browser Netfront/IE
My laptops, DS Lite, Wii can connect and work with the router...
Any help will be highly appreciated
Click to expand...
Click to collapse

hencre said:
hi,
Im having the same problem. No MAC filtering & no encryption on ADSL router.
HTC touch can connect to the router at 192.168.1.1. But it does not connect to any other web page.
Message shown is: "Page cannot be found. Check the name and try again."
Any other tips.
Thanks in advance.
Click to expand...
Click to collapse
Same problem I am having now. I can connect now wifi, but get same error.
??????

Wifi Problem!
Hi guys,
I've got a problem and I'm hoping you can help me out..
I've got a HTC TOUCH and when I got it the Wifi connection was working just fine.. I could connect to any WIFI network and Browse the internet.
After a month or two, my phone wouldn't connect to my home wifi network anymore. And neither would it connect to any other wifi networks (I tried!)..
I've been all over the internet trying to figure out what could have happened and if someone else was having these problems to.
I just can't find the answer and I feel like I already tried everything I could think of..
Hope some of you knows what to do..

I'd suggest looking at the Touch forum... I've got no experience of Touch devices, but it may be a Radio ROM issue...

kinda same issue I am facing ! donno
MY HTC TOUCH never connects to NETGEAR WIRELESS ACCESS POINT
but finds LINKSYS routers in a jiffy :O
are Wireless Access Point and.. Wireless routers different
they both emit diff. signals ?

I have the same issue with a TYTN II, can connect to the wireless, but can't open any web pages.

problem with htc & WPA-PSK passkey 25 characters
My htc tilt connects almost everywhere, but i have a problem with wpa-psk at work. The password is from 25 characters, I read some articles what WM cannot handle such length. Maybe it's possible to edit somehow the registry?

I have the same problem guys, what can we do to find a solution i tried everthing i could, and i even tested it out with my 2 wireless routers, and at public places it connects (at home it doesnt connect though).

shirreer said:
Scratch the last post! I had the same problem with my TOUCH..Just put the power level to the max (i.e. go Start -> Settings -> Connections -> Wireless LAN -> Power Mode -> and slide all the way LEFT to Best Performance) and all hail ..your problem solved
Click to expand...
Click to collapse
Thanks a lot!
I had exactly the topic problem with manilla rom on my kaiser, could not use wifi any more. But with just sliding the meter to 'Best Performance' as suggested, wifi it once again works like a charm.

HTC Touch wifi solve
I had the same problem with my htc in WEP it dosen't browse, I changed the router to a better wifi protection like WPA-PSK, connected and worked fine, for some reason it only work's fine for a couple of minutes, I readed this post to put the sidebar in best performance and now everything works fine. An advice don't use WEP it's not secure at all.
http://en.wikipedia.org/wiki/Wireless_security maybe you fine this interesting and helpful.

I'm running into a problem were I can connect to an AP at work and surf the net fine but when I disassociate I cant connect to it again for a whole day. The AP must be saving some info and therefore will wait for the DHCP lease time to finish before allowing the touch to re-connect. I tried my laptop and was able to connect 3-4 times and never have a problem so it is isolated to the touch and windows mobile 6.1. To find some more info out I was able to clone the mac of the touch and use it as the laptops wifi cards mac. It connected fine on 3 consecutive tries.
Maybe windows mobile is missing some commands when disassociating from an AP and as a result leaving info out in nowhere land confusing the router.
Thanks for any help!

ok, here's me joining the club... dunno what happened... working one day, getting crap the next.
exact same problem as everyone else...connects to the wireless network, then when you try to surf, page cannot be found...

Exact same problem here.
In the beginning everything fine. Connecting to my home WiFi and using the internet without problems (weather, stocks, opera, email, google maps, even skype voip).
Then, last month, all programs are unable to find anything on the internet, although the device reports it is connected to my (unchanged) home WiFi.
All these programs work fine when the device is connected to the internet through activesync (usb cable).
Also this whole time I have been using my home WiFi with a laptop from both Vista and Ubuntu, with no problems, so I guess it's not the router.
Also have read in other fora about these wifi working - wifi not working "cycles" other people have had, with various WM devices. And various tricks like shutting wifi off and immediately on again.
I even hard reseted the device. Problem still there.
WTF?

Connected once only
Connected once only for a few minutes to my home router dir 310 D-Link, worked fine and fast. After that I closed the connection. Next day I tried to connect but my HTC Touch 3G doesn't see the router. I see any other routers, but I do not see mine. I connected to some friends routers with WEP and WPA encription just to be sure the phone working. During this I didn't changed the router or the phone settings. It is very strange. The problem maybe comes from the router.

I'm having the same issues with my HD2. Looking all over the place and seems to be a common fault, but thus far with no cure, I tried the power save mode
From new it worked like a dream, but then one day it would connect to AP's but act as if not connected. I flashed my ROM with the VERY impressive Merlion Leo v 2.66 and it all started working again. Then yesterday, it stopped again. I don't want to reflash, so I'm working hard to find a cure, and will report as soon as I find one.
---EDIT---
I've found a cure (for mine at least), not sure if it will work for everyone, and haven't managed to test it at any other AP's except for my home Router, but all I did was set the network card properties (Broadcom 802.11 DHD Network Adapter) to 'Use server-assigned IP address' instead of 'Use specific IP address'. I'm not sure why this worked as there was no IP address conflicts because there were no other devices connected to my router when I had problems, but it works for me, hopefully permanently
Good luck.

Try this. Its work perfect for me!
http://forum.xda-developers.com/showpost.php?p=10035476&postcount=10

Elfin can't connect to belkin N router

Hello... Got a Touch recently, and doing research found this forum. One of the best findings lately for me: already flashed the phone with a WM6.1 ROM and updated my radio successfully. But I have a problem (even before the flashing):
I can't connect to my wifi. I have a belkin N router. Have tested almost everything: updated the router's ROM, updated the phone's radio, turned off security, assigned manual IP's, etc, but with no success... so I'm running out of ideas. I can connect to another people's wifi's tho.
Anything I have missed? Just an incompatibility? (which means I'm screwed)
Thanks a lot

is t on n only mode?
touch is g/b as u probably know
if not, try with no security to see if it connects

Yeah, it is in a multiband setup (g/b/n).
Also tested with no security. No sucess.

I have the same problem, I'll let you know if I find a solution.

Same thing... I'm trying to figure out a solution, any findings, will post here.

I tried to connect my Touch to my old netgear 802.11b router at home without any success. I did a lot of "googling" on the subject, and only found that many concluded that it wasn't possible to do so.
Also, I have AT&T, and they are offering free hotspot WIFI connectivity to their customers (which is intended for laptops). My touch detects the WIFI signals, but I have yet to find out how to make a connection.
It seems like there should be a way to do it somehow though!
Anyway...
Best Regards!

pl, when you go into your Settings -> Connections -> Wi-Fi, can you see your wireless network being detected?
The only things that spring to mind at the moment, are the basics for normal connection ...
1. Network type (B/G/N)
2. Authentication (password)
3. MAC Filtering
Here's what I would do ...
1. Reset router (usually has default button at the back).
2. Set it up for DHCP (sometimes cures a lot of problems).
3. Set simple WEP with password.
4. Obviously a network name (make sure it is not hidden, also make sure AP is enabled)
5. Set channel
6. Set mode (Network type) to mixed.
7. Save and reboot.
8. Soft reset Touch
9. Go to Settings -> Connections -> Wireless LAN
10. Activate Wireless and see if your SSID (network name) pops up. From here you can see signal quality and IP (to make sure you got it from DHCP).
Give it a shot and let us know what happens.

same problem here, really annoying!

Strange, I have never had problems with mine (had it connected to a couple AP's already). In fact, it's easier than connecting my laptop to a WLAN.
You have anything else that can connect to your Router? pc or something.

My Touch can connect to other routers, and I have 2 PCs at home which connect to my Belkin N router, I just can't connect my Touch to it.
I found a solution
Customer Call Details Nov 13 2008 04:37
I have an HTC Touch that can connect to other hotspots, but not to my home Belkin router. Sometimes, if there is another connection available, it can see the router, and says that it is Available, but cannot connect; other times it won't even see it. I have checked for firmware updates, but I have the latest. Any help would be greatly appreciated.
Belkin Response Nov 14 2008 22:18
Hi Lilburd,
Thank you for contacting Belkin Technical Support.
We understand that the HTC Touch does not connect to the router. We apologize for the inconvenience caused.
Please follow the steps given below to update the firmware and configure the router:
We recommend that you update the firmware from a computer that is connected to the router with an ethernet cable.
Please download the latest firmware on the router from the link given below. Download the file "3.01.29":
http://www.belkin.com/uk/support/article/?lid=enu&pid=F5D8233uk4&aid=10288&scid=0
and save it to the computer.
- To update the firmware, log on to the router`s web interface by typing in http://192.168.2.1 in the address bar of the browser. The computer should be
connected to the router with an ethernet cable.
Note: If you have changed your Router’s IP address, use that IP address.
- By default, the password is blank. Click the "Submit" button.
- Click on "Firmware Upgrade" under the option "Utilities".
- Click on “Browse” and select the bin file that you have downloaded.
- Click on “update” and follow the wizard.
- After updating the firmware, restore the router to factory defaults by clicking on "Restore Factory Defaults" under "Utilities".
- Reconfigure the router.
Please follow the steps given below for configuring the router:
- Connect the computer to the "LAN" port on the router and connect the modem to the Internet/"WAN" port, using Ethernet cables.
- Take a paper clip, insert the paper clip in the reset hole of the router and hold it for 15 seconds.
- The power light will flash and then come back "ON" solid, indicating that the router is being restored to factory defaults.
- The corresponding lights on the front of the router should be lit up.
- On the computer, check if you have an IP address in the range of 192.168.2.x.
- If not, specify a static IP address, gateway and "DNS" address by following the steps given in the link-
http://web.belkin.com/support/kb/kb.asp?a=2824
- Log on to the router web interface by typing in http://192.168.2.1, in the address bar of your browser.
- By default, the password is blank.
- Click on "Connection Type" in the left hand column under "Internet WAN" heading.
If the connection type is Dynamic (cable):
- Choose "Dynamic" and then click on "Next".
- Type in your “Host Name”, if your Internet Service Provider has provided it. Else, leave it blank.
- Click on "Change WAN MAC Address".
- Click on the button "Clone".
- Click on "Apply Changes".
If the connection type is PPPOE (DSL):
- Choose "PPPOE" and click on "Next".
- Enter the user name and password given by your Internet Service Provider.
- Save the settings.
- Click on the "Home" link at the top of the screen.
Internet Status should show "Connected" on the top right hand corner of the web page.
If the problem persists, please get back to us with the following information:
1. Type of connection provided by your ISP (Is it PPPOE, Dynamic or static).
2. Name of the Internet service provider (ISP).
3. Version number of the router. You would find the version number on the bottom of the device. It would be a number in a series of thousands with a prefix “ver.”.
4. If the internet connection is stable on the computers using the router?
5. If the HTC Touch detects and connects to other networks in the neighborhood?
Lilburd, if you need further assistance please feel free to write back to us and we will be happy to assist you.
Regards,
Belkin Technical Support.

That really is strange. The way I see it, WLAN is a standard. It's like BT, any headset should work with any BT phone, as would any wireless device work with any wireless device
Maybe force the router to only broadcast in G (or even B) and see what happens? (I know, I'm reaching now )

Tried everything so far, no success. Even with no security enabled.

same problem here, Very Annoying, tried every thing

HTC Diamond doesnt connect to WiFi!!!!!
EMoeHTC said:
I tried to connect my Touch to my old netgear 802.11b router at home without any success. I did a lot of "googling" on the subject, and only found that many concluded that it wasn't possible to do so.
Also, I have AT&T, and they are offering free hotspot WIFI connectivity to their customers (which is intended for laptops). My touch detects the WIFI signals, but I have yet to find out how to make a connection.
It seems like there should be a way to do it somehow though!
Anyway...
Best Regards!
Click to expand...
Click to collapse
ANY SOLUTIONS TO THIS ISSUE YET....WAITING TO USE WiFi on My HTC-D.
THanks

Same problem here, N1 Vision router and XDA Orbit, both running on latest firmware. Wrote to Belkin support describing the issue. Here's their reply:
Code:
Thank you for contacting Belkin Technical Support.
We understand that you are not able to connect XDA Orbit WM6 communicator wirelessly.
To resolve this issue we suggest you to open ports on router.
Please collect the port number from the XDA Orbit WM6 communicator vendor and enter under "Inbound port" & "private port".
-Please open the Internet Explorer and in the address bar type in "192.168.2.1" and Enter.
-Leave the password blank and click on "submit".
-Click on "Virtual server" under the "Firewall".
-Enter the port number under "Inbound port" & "private port".
-Enter the IP address of this computer under the "Private IP address".
-Check the "Enable" box and click on "Apply changes".
George, if you need further assistance please feel free to write to us or call us on 08456077787.
You can also contact us through our online chat support at:
http://www.belkin.com/chat/technicalsupport.aspx
Regards,
Suzane Taylor
Belkin Technical Support
Utter nonsense...

I just got my Touch Diamond from Sprint and am having the same issue. I have a Belkin N+ Router that is in g/b/n wireless setting.
The phone just simply will not see the SSID even if you put the settings in there manually. What it does see however is the guest SSID my router emits and connected to it without any issues. The guest account is a feature of my router gives friends access to the web but denies access to internal network.
Out of curiosity changed my routers wireless bands to only G/B and all of a sudden my phone can see the network. Unfortunately for me I rely on the N part of my network to connect my laptops and do streaming HD so leaving it on G/B is not acceptable.
I just connect via the guest account, anyways its not like my phone would have been able to see the internal home network anyways.
Just my 2cents

I have the same issue.
Used to use a D_Link G router, but recently upgraded to a belkin N-draft one.
My laptop connects on G, and my desktop on N, so I can't switch N off and just use G.
Anyone found a solution yet? It's bugging the hell out of me!

I posted a fix on page one that should work. You have to update your firmware.

Did u all using any encryption security?
128bit WEP - touch have a problem of connection
64 bit WEP - works

have you enabled easypairing, (WiFi easypairing : Enabled) if so turn it off or press the required button sequence on the router to connect.

New Touch Diamond 2 Wifi Wont Connect

Hi Guys & Gals,
I have a brand new HTC Touch Diamond 2, on O2 network - this is an untouched device, all i have done is booted it up and sync'd it with my PC,
I have tried to connect the device to to wireless networks now with no luck.
1. My home connection - security enabled WPA-PSK password protected, The phone can see the network, i type in my network key - i also checked the password on my router setup. The little spinning circle comes up and try's to connect with no luck. It will then keep trying for as long as the wireless is on
2. Home connection again with no encription - again the same thing
3. Work connection WEP secured, type in the key, same thing again.
Has anyone encountered these sorts of problems before in the past - if so how do i fix it so i can connect wirelessly.
Cheers Guys
JdeRonde

Doubt if this is an issue with the phone more likely to be a setup of the wireless.
What router do you use?
Do you have MAC Filtering enabled?
Do you use your router as a DHCP server?
Are there any error messages displayed on the phone?
When it doesnt connect and you tap the notification area (top bar to the right of START) do you have any messages there?

jderonde said:
Hi Guys & Gals,
I have a brand new HTC Touch Diamond 2, on O2 network - this is an untouched device, all i have done is booted it up and sync'd it with my PC,
I have tried to connect the device to to wireless networks now with no luck.
1. My home connection - security enabled WPA-PSK password protected, The phone can see the network, i type in my network key - i also checked the password on my router setup. The little spinning circle comes up and try's to connect with no luck. It will then keep trying for as long as the wireless is on
2. Home connection again with no encription - again the same thing
3. Work connection WEP secured, type in the key, same thing again.
Has anyone encountered these sorts of problems before in the past - if so how do i fix it so i can connect wirelessly.
Cheers Guys
JdeRonde
Click to expand...
Click to collapse
I too had problems with WIFI. My home work network was visible but it would immediately drop or not be able to connect. A few days later it started working flawlessly and I have no idea what changed.
I am sure you have tried a soft reset but just in case...
Tony

I have a NetGear DG(Some Number) v4 ADSL wireless router, which i have set up and works for all of my other devices (ie. Laptops, PS3). With a simple encription key.
I get no messages etc, all it sais is that its 'not connected' and there are no new notificatons
It then persists in trying to connect again and again, when it cant connect for a while, it then comes up with 'new network connections found' in the notificatins area.
I have switched the power mode to best performance with no luck.
I have tried on 2 different networks now. including with all encription off. WEP and WPA-PSK - This is driving me nutz cuz i love the phone, i just want to use it to browse the web without paying out the nose for it.
DHCP server is dynamic from my ISP.
I have contacted HTC now about the issue, but im going to feel so stupid if it turns out to be somthing simple like a setting on the phone somewhere.
But thanks for the reply

Have you checked you arn't using MAC filtering?
Log-in to your router and check under Wireless settings > Wireless Station Access List.
While you are on your wireless setting page check what Encryption your using for WPA-PSK? TKIP? (The wrong encryption chosen will cause you not to be able to connect)
Ok maybe telling you how to suck eggs but on your phone:
Settings > Communication > Wifi
Select Advanced at the bottom right.
Select Change Network
Click Add new...
Type in the name of your network (The SSID also found under wireless settings, Case sensitive)
Select Connects to: The Internet
Leave the other two boxes unticked.
Click next.
Select the correct Authentication - WPA-PSK is different to WPA2-PSK. You will probably be using WPA-PSK.
Select the correct Encryption (Propably TKIP)
And type in your Network Key
Click Next and Finish.
How does this fair and what are the results of checking info on wireless setting page?

Im at work at the moment trying to connect to the WEP connection,
This connection most deffinatly does not have mac filtering on it, just asked the network tech.
Okies.....
Changed the network key to.... Shared key and it works
so i am guessing that it must be somthing to do with my setup at home..
Cheers guys

Cool.
Just match up the Authentication / Encryption / SSID and Network Key from the router to your phone setup and you should be fine.

HTC TD2 Wifi issues
Hi
There's some discussion around the web about this problem of encrypted wifi connectivity: a few things to note
1] the TD2 is _very_ sensitive to the power settings applied to the wifi chipset.
The default power saving settings are only likely to work if all other on-board devices - bluetooth, HSDPA, GPS [and maybe even the screen] are either off or in low power mode: the general recommendation seems to be that one adjusts the wifi device power to be "best performance" if one wants to guarantee connections.
2] several people have reported that both the wifi device [card] and the settings for the particular wifi lan [SSID] to which you are attempting to connect should both be configured for "Work" rather than "The Internet".
3] these secured/encrypted connection failures are not about the WiFi access point or router: I've personally tested with several different makes and models of Router and Access Point [3com, Cisco, Enterasys, Netgear, DLink, Belkin etc] - both on my own and on client networks where I have complete control of security, and have also methodically tested every single combination of TD2 setting for WEP and all variants of WPA. In each case my TD2 has failed to make a valid encrypted connection.
The same device will happily connect to "open" unencrypted access points and routers.
Other models of HTC device, such as the Tytyn II and Touch Pro work fine on the same access points and routers: so we can be pretty sure that this is specifically a TD2 issue.
Conversations with HTC's European Tech Support on this issue have not been helpful to date, but they HAVE pushed the issue further up the line, so there's a chance that we'll see a resolution.
Robert

Unknown Wi-Fi problem

Hello,
I am having the following issue while using Wi-Fi: in the list of available networks is a type of connection I have not seen before. It seems to be a modification of sorts of my own wi-fi connection, but if the device connects to it, I cannot connect to either websites or to the other PCs on the LAN.
This connection is represented by a different type of icon as you can see on the screenshots. I have not created it, but it may be a remnant from my previous connection - look at the names, one has a space in between, the other hasn't. I created the new one (without the space) after I changed my router to D-Link's DIR-600.
An interesting thing about this connection is that the device does connect to it even when not anywhere within range of the router (say 2-3 km.)
Any ideas?

This the symbol for an Ad-Hoc network (Computer to Computer). You can probably remove that connection and still be o.k.

Thanks!
I tried removing it, but it then creates it again.
Of course, I can always disconnect and connect to the other network.
I have never dealt with Ad-Hoc connections. Isn't this connection supposed to enable access to the other computer then? Like LAN? And why does the device connect to this network when far outside the router's broadcast signal?

Database Users

welcome