Related
So I bought a new housing for my O2 XDA II Mini, during the removal of the display ribbon I broke the little black part on the display connector which holds the ribbon down, and after hours of trying to get the ribbon back in and secured I have bent the pins in the connector to buggery.
The ribbon appears to be untouched, however the connector which the display ribbon goes into is broken.
Is there anywhere I can get hold of one of these little connectors to replace my broken one, obviously very sensitive soldering will be needed to remove the old one and solder the new one in place.
Alternatively, does anyone know any mobile phone repair shops in Auckland, New Zealand who would be able to help out with my situation?
I fear all i'm going to hear back is "the motherboard needs to be replaced", however I am determined not to go through this route, as I am a poor student and the phone sounds as if it functions fine, makes the beepy noise when first starting up on the setup screen.
I was very careful with the actual screen unit while removing it, and I have had signs of life earlier on in the broken connector episode, however I can no longer get anything showing as I can't fit the cable in.
Cheers for any help.
Anything would be appreciated.
"obviously very sensitive soldering will be needed"
And that only can be done by machines/robots. I don't think humans are even able to sloder those kind of connections...
But, could you post a picture? cause I might have suggestions on how to fix it. One would be to bend back the pins on the tiny slot with a toothpick and when done to tape the flatcable, so it stays there.
I've maybe got a spare creen for you.
g0atNZ said:
So I bought a new housing for my O2 XDA II Mini, during the removal of the display ribbon I broke the little black part on the display connector which holds the ribbon down, and after hours of trying to get the ribbon back in and secured I have bent the pins in the connector to buggery.
The ribbon appears to be untouched, however the connector which the display ribbon goes into is broken.
Is there anywhere I can get hold of one of these little connectors to replace my broken one, obviously very sensitive soldering will be needed to remove the old one and solder the new one in place.
Alternatively, does anyone know any mobile phone repair shops in Auckland, New Zealand who would be able to help out with my situation?
I fear all i'm going to hear back is "the motherboard needs to be replaced", however I am determined not to go through this route, as I am a poor student and the phone sounds as if it functions fine, makes the beepy noise when first starting up on the setup screen.
I was very careful with the actual screen unit while removing it, and I have had signs of life earlier on in the broken connector episode, however I can no longer get anything showing as I can't fit the cable in.
Cheers for any help.
Anything would be appreciated.
Click to expand...
Click to collapse
Hi, I've still got a SPV 500 and a MDA Compact, need to find it if you want you can have my MDA Compact screen.
Just PM if you are interested.
Hey Guys,
Well, I'm a bit gutted really! I dropped my XDA Mini S on the floor with the charger in and the connector IN the phone has come apart from inside the phone. The little metal bit is practically hanging out. I'm wondering, if i were to take the phone apart could i re-connect the little part? (I have a soldering iron if thats as simple as its going to be?)
Just wondering if anyone had any guides on how to take the phone apart and take a look at whats wrong?
Any help would be so much appreciated!
Many Thanks,
Tom
The service manual is hosted on the ftp site.
ftp://ftp.xda-developers.com/Wizard/Docs_Tutorials/
Hope this helps.
I suspect you probably broke the socket off, but if you have a soldering iron, you might as well try to get a new mini USB connector to work with.
You might try Pocket PC Techs:
http://www.pocketpctechs.com/main~unit~UTStarcom_XV6700-554~area~repairs~item~REP-USBCON01~name~UTStarcom+XV6700+Mini+USB+Connector+Replacement+Service.htm
I rang them up about an issue I had (screen on the fritz) and they seemed pretty knowledgeable and helpful.
Alternatively there's a company I found today in the UK. I can't vouch if they're good or not.
http://www.xdarepairs.co.uk/home.asp
Good luck.
Well I also have an issue with my wizzard... the mini jack connector (of the handsfree) is a bit loose.
What I am saying is that it does have a good connection with the rest of the circuit and sometimes the sound of the speaker goes off, then I have to insert the habdsfree and tickle it a little bit until it has a good contact.
? have some basic soldering experience,do you think I should give it a try?
Given my device has been apart too many times for me to admit to I thought I'd crack it open to take a pic for you guys. Not sure if this pic will help for those wanting to do some soldering:
Very large pic: http://farm1.static.flickr.com/216/452691530_f47801708f_o.jpg
Excuse the dust.
Ah! That picture at the bottom is exactly what I needed. The metal but at the bottom (the big sqaure) has totally sheared off....bloody thing. Thanks so much for the info on the repair guides. I may give those repair guys a call if i can't get it to work myself.
Thanks alot you guys
As for you WizeMan, it all depends on if you wish to void your warrenty or not. At the end of the day, I installed WM6 on my device so O2 would give me the finger if i tryed to claim. If I'm honest, I'm getting an upgrade next month so I'm not to bothered if I balls it up! Would be nice if I got it working though....
Lemmie know how you get on
unlock k-jam
i read all your write about how to unlock k-jam device but after all i get this message:
Lock Status: 0000000000000000
SIMLock Code: █⌠═eי∟80Γ█Σ☻< δ♠
how can i get it from this .........
lironasseo said:
i read all your write about how to unlock k-jam device but after all i get this message:
Lock Status: 0000000000000000
SIMLock Code: █⌠═eי∟80Γ█Σ☻< δ♠
how can i get it from this .........
Click to expand...
Click to collapse
A little bit of a thread hijack but that means it is SIM unlocked.
Let me tell you my news, my friends.
I opened my Qtek 9100 and fixed two serious issues regarding this phone, using... sponge (the one we use to wash the dishes)
1. I put some into the stylus socket (from the thin space it has) and also
2. On the top of the mini jack socket so when i assembled the housing it blocked it from moving (2 of the contacts are no more soldered and i dint have a soldering iron at that time)
Anyway, both operation went ok and my phone is more than fully functioning. Now the stylus is hardly (in a good way) comming out (it first gets longer then comes out).
I wanted to do also the safe singal fix, but didnt find the photos to apply it correclty, so if someone has them, please give link. If you need any info about the "Sponge" Hacks, just post or pm
WizeMan said:
Let me tell you my news, my friends.
I opened my Qtek 9100 and fixed two serious issues regarding this phone, using... sponge (the one we use to wash the dishes)
1. I put some into the stylus socket (from the thin space it has) and also
2. On the top of the mini jack socket so when i assembled the housing it blocked it from moving (2 of the contacts are no more soldered and i dint have a soldering iron at that time)
Anyway, both operation went ok and my phone is more than fully functioning. Now the stylus is hardly (in a good way) comming out (it first gets longer then comes out).
I wanted to do also the safe singal fix, but didnt find the photos to apply it correclty, so if someone has them, please give link. If you need any info about the "Sponge" Hacks, just post or pm
Click to expand...
Click to collapse
I'm still trying to get the a new fascia and will probably shove an eraser bit into the stylus spring mechanism to ensure the defect never happens. Also how did you discover the break in the solder joints on the headphones jack? I have a funny situation where the left channel of the headphones doesn't work but I suspected the headphones (the plug has to be pulled at an angle to get any sound out of the left) but now I am thinking it may be the socket itself.
By the way the reception fix pic doesn't load for me either but I unless you truly need it, don't waste your time doing it; I always have all 4 bars and sometimes have 2 bars.
AsGF2MX said:
I'm still trying to get the a new fascia and will probably shove an eraser bit into the stylus spring mechanism to ensure the defect never happens. Also how did you discover the break in the solder joints on the headphones jack? I have a funny situation where the left channel of the headphones doesn't work but I suspected the headphones (the plug has to be pulled at an angle to get any sound out of the left) but now I am thinking it may be the socket itself.
By the way the reception fix pic doesn't load for me either but I unless you truly need it, don't waste your time doing it; I always have all 4 bars and sometimes have 2 bars.
Click to expand...
Click to collapse
Allright here is the deal.
1. I found out the break in the soldier joints when i opened it. I was really suspicious about it because when i inserted my headphone jack into the connector, i had problem with the contact; the connector was loose and it muted my phones speaker. When i disassembled the phone using the service manual i saw with my eyes that the the joins where f-ed up.
2. I dont really need the signal hack i just wanted to experiment, i have 2.25.11 cingular radio rom and its great.
Btw i suppose you should better use the sponge, because the rubber may wear off but not the sponge...
Thanks for the tip on the sponge. I am going to grab a used but allegedly "like new" body from eBay and also get one of those covers as well.
Hello! could people please share tips and things to remember when buying a used universal? I mean what are the things that you should do to check or find tell tale signs of defect, hardware, the firmware the os, I have already done a search in the forums and already know some, but there might be things that I have missed, so help would be very nice, I will be meeting the seller so I get to inspect the device up close so it would be nice to armed with the info how to inspect the device from how to check the bootload etc.
Thanks for the help and I hope that this helps others too
The Universal can be bought cheap at german eBay. Look for MDA PRO. You should be able to purchase one for around or less than 100 Euro.
Preferably look for the following signs:
1) Unmodded. Many users got the Universal within a contract from the operator, but did not use it much, because it is too big for them. Such Universals are normally in good condition. When advertised that it ships with an OS different than WM5, you know that the owner has been flashing it. I personally don't like that, because that means it belonged to a power user and must be more worn out.
2) Warranty stickers. Make sure the hinges have the warranty stickers inside. If they are missing, the device has been opened. You don't want to purchase one that has been opened.
3) Screen. Screen should be without scratches and should have had always a screen protector.
4) Speaker. The external speaker which is used for calls can break, as it is fitted with some kind of pogo pins. Make sure it is working.
If you get to test the device first, do as this:
- do a call (bring your SIM card)
- check WLAN and Bluetooth (bring a headphone and try it somewhere with WLAN activity)
- bring a SD card and see if it is read
- check for bad pixels
- play a song
- take a picture
- try the keyboard and touch screen
- try all the buttons
If everything works, that is the best you can check it for.
Of course it could break the next day, but it shouldn't.
Cheers,
vma
Great guide vma!
I´ll just add:
Take special care on the swivel piece (The one that gives Uni it´s great and unbeatable form factor: PDA - Micro Lap top)
take care of another thing when i bouted my universal after i used it for about 1 week the phone was hangs soo much the reason was in the memory crd .....so you must try a memory crd and play a small video on it about 10 minutes
The most important thing everyone forgot to mention is USB port. When looking for a device, see if the port moves in any way or wiggles in its opening. See if the device synchronises with AS, charges etc.
The fact the device had been flashed or opened wouldn't play a huge part for me if everything else works well and the body is in sound condition, e.g. the hinge is not loose, the screen rotates and closes properly, all keys are present and work, keyboard backlight works with and without sensor etc.
Speakers don't just break, as post No2 claims (POGO PINS??), but it is good to check that phone is capable of making/receiving calls, you can hear the other party and the other party can hear you, can play music and earphone plug is in working condition/attached properly
Not reading SD or SIM card is a biggie, dim screen, lost touch sensitivity, scratched or damaged digitizer, worn out buttons - all obvious signs. You can open the back, remove the battery and SIM card and check for a small white blotting paper sticker covering the small mainboard pins under the SIM card, any change in color towards pink - do not buy.
@enigma1nz:
Shame on me, I did indeed forget the USB port!!! You should of course check both: charging and Active Sync connection. A broken USB connector is a mayor issue and hard to solder without proper equipment.
Regarding the speaker: I am speaking out of experience, as one faild on me. The speaker is like a small button and it has two contact plates. They are not pogo pins, but act like them. The speaker will be pressed by the case against two contact points on the PCB. What happens is that apparently some car-holders do too much pressure on the sides of the Universal casing, causing the speaker contacts to bend back and forth everytime the phone is placed or removed from the holder. After a few months the contact gets worse and worse until one of both plates brake off. Because they are so tiny, it is impossible to repair the speaker - believe me, I have tried. I ended up buying a new speaker cell at eBay.
Cheers,
vma
vma said:
@enigma1nz:
Shame on me, I did indeed forget the USB port!!! You should of course check both: charging and Active Sync connection. A broken USB connector is a mayor issue and hard to solder without proper equipment.
Regarding the speaker: I am speaking out of experience, as one faild on me. The speaker is like a small button and it has two contact plates. They are not pogo pins, but act like them. The speaker will be pressed by the case against two contact points on the PCB. What happens is that apparently some car-holders do too much pressure on the sides of the Universal casing, causing the speaker contacts to bend back and forth everytime the phone is placed or removed from the holder. After a few months the contact gets worse and worse until one of both plates brake off. Because they are so tiny, it is impossible to repair the speaker - believe me, I have tried. I ended up buying a new speaker cell at eBay.
Cheers,
vma
Click to expand...
Click to collapse
And believe me, I repair devices for a living. Thanks for the run-through, although I could give you the same. It happened to you, doesn't mean it happens often or it is a fault in design. I could give you a list of design faults in quite a few models of expensive cellphones on the market today, the mentioned speakers are not one of them.
I appreciate, the help people! any more inputs? I am happy that all the previous posts were, about how to inspect the device upfront and some other useful tips what to check other inputs will be highly appreciated
Battery can be also considered. Some are sold with good batery some with dead battery. It is not so expensive, but costs something. In general if battery shows less than 50% and devidce still works (even under load) that is a good sign.
Also as for the touch screen - the best test is to open note taker and try to paint something. The painted line must exactly follow the stylus movement if it jumps somewhere, then the touch sensitive layer is bad. I bouht such UNI on eBay (was described as perfect working order), had to replace the digitizer myself.
I do prefer buying not working UNI's on Ebay with good display. Once I bought not booting one - mtty job fixed that. Other time I bouht one where the display was still off - the flex cable popped out from connector. Etc....
Thanks for all the advice people! now, please welcome me to the HTC universal family, (well actually, I have a Dopod 900 but what the heck all are the same right?) your inputs had been essential, for me to get my new baby without any hitches I hope that nothing manifests after the one week assurance the seller gave me
Special thanks to enigma1nz for all the patience and help provided to me I asked her a lot of questions in the pm's but she answered in full detail
Now I have my own device so I will be flashing away, I hope without any problems. Again my thanks to the community hopefully there are more inputs for others who are thinking of buying their 2nd hand universal via meet ups
Excellent news! Congratulations!!! And welcome to the Uni family, of course. As you can see, we are one friendly bunch, all help and support will always be available. Have fun
Damn, I was hoping to do a very good Marlon Brando Godfather impersonation with 'Welcome to the family'
LOL
You started in the right direction!
to midnightsights : welcome
orb3000 said:
LOL
You started in the right direction!
Click to expand...
Click to collapse
No, sweetie, the right direction would be an Orb3000 impersonation and 'Welcome to the forums', but I was worried, being Orb2000, hehe, that I simply won't be able to compete with a more updated version
enigma1nz said:
No, sweetie, the right direction would be an Orb3000 impersonation and 'Welcome to the forums', but I was worried, being Orb2000, hehe, that I simply won't be able to compete with a more updated version
Click to expand...
Click to collapse
LOL.........
enigma1nz said:
No, sweetie, the right direction would be an Orb3000 impersonation and 'Welcome to the forums', but I was worried, being Orb2000, hehe, that I simply won't be able to compete with a more updated version
Click to expand...
Click to collapse
Thanks dear, you´re nice
you´ll be Orb4000!!!
Cheers and have a nice weekend,
I just bought a replacement power button/ flex cable for Nexus of ebay. Took me around 30 minutes to replace it but its fully working right now. Its around 30 £ .
Item name it "Flex Cable Repair Parts for HTC Google Nexus one G5 1"
Just thought i let you know .
Any pictures?
Is it a tricky fix? I replaced my digitizer just fine so hopefully this wouldn't be a major repair job in comparison. Would love to have my power button working again!
I don't understand why you fixed it yourself, I sent mine back to HTC.
stinkypete said:
I don't understand why you fixed it yourself, I sent mine back to HTC.
Click to expand...
Click to collapse
How much did it cost for the repair out of interest? Did it take them long to get it back to you?
Just curious if to you it looked like a bad button connection or a bad cable? I know sometimes the buttons get crud in them so they dont make a proper connection...
Great info. Too bad we don't have step by step pics. How did you take the phone apart and how deep did you have to go?
Does anyone know why the power button breaks? I have my N1 a year now and (luckily) i never had a HW issue. anyways i was just wondering why it breaks .
Step by step pics would have been nice.
commodoor said:
Does anyone know why the power button breaks? I have my N1 a year now and (luckily) i never had a HW issue. anyways i was just wondering why it breaks .
Step by step pics would have been nice.
Click to expand...
Click to collapse
The power button itself has a small cylindrical piece of plastic which pushes against and presses a small connection that sorta clicks (Which gives you the tactile feedback you feel). I think the problem occurs when either 1) The piece of plastic either bends/breaks/gets damaged in some way that makes that contact much harder to produce 2) The connection is connected to the phone via a cable/flex, however due to the Nexus one design it is bent around in order to be below the power button, while this is fine for the majority some devices, including mine, have seen the flex become damaged for whatever reason and either function intermittently or not at all.
It's also interesting to note that there is nothing holding the flex or the connection in place except for the design itself i.e. the battery bay plastic holds it all in place. My power button was never that responsive (But got progressively worse) so this may explain why.
Its always flex cable breaks and there is no way you can replace just the flex cable.You can find plenty of disassembly instruction over the net and yes you need to disassembly it to the pieces( still less to do than to replace digitizer.)I had a seal broken so i couldn't send it to HTC.
Hollow.Droid said:
The power button itself has a small cylindrical piece of plastic which pushes against and presses a small connection that sorta clicks (Which gives you the tactile feedback you feel). I think the problem occurs when either 1) The piece of plastic either bends/breaks/gets damaged in some way that makes that contact much harder to produce 2) The connection is connected to the phone via a cable/flex, however due to the Nexus one design it is bent around in order to be below the power button, while this is fine for the majority some devices, including mine, have seen the flex become damaged for whatever reason and either function intermittently or not at all.
It's also interesting to note that there is nothing holding the flex or the connection in place except for the design itself i.e. the battery bay plastic holds it all in place. My power button was never that responsive (But got progressively worse) so this may explain why.
Click to expand...
Click to collapse
Thnx for the explanation. I get it now. maybe it smart to always use trackball wake .
Ra1stlin said:
Its always flex cable breaks and there is no way you can replace just the flex cable.You can find plenty of disassembly instruction over the net and yes you need to disassembly it to the pieces( still less to do than to replace digitizer.)I had a seal broken so i couldn't send it to HTC.
Click to expand...
Click to collapse
I did some googling and found a few images of that component, I remember taking it out and it was pretty simple so it should be just fine! Thanks for the info!
Is it the Power button part that you changed ?
Hi,
I have found a photo of the power button part, can you tell us if you changed the full part shown on the photo ?
androidguys.com/2010/09/08/manage-nexus-broken-power-button
And i think you paid it way too much expensive ?
Thanks.
I just replaced my flex cable as well as the loud speaker as well.
iFixit has a few pictures and there is a video on youtube, of the taking apart process. Unfortunately I can't post links
There are two little rubber parts that will likely fall out during the mainboard removal. One goes underneath the connector beside the sim card and one is a part of the microphon.
I wish I could have taken pictures of where those parts go, but alas, my only camera right now is my nexus, so....
BTW, I bought my parts at Mobile Brando. Quite well priced as compared to many other stores of the kind.
was it the whole board that you've replaced? or just the flex cable for the power button. can you further elaborate the steps that you've done?
So this is the item that you purchased? http://mobile.brando.com/google-nexus-one-mother-board-flex-cable-ribbon_p6193c1023d88.html
Can you confirm that the 3.5mm jack is on that board? Additionally, is that motherboard and flex cable for the AMOLED version or the SLCD version?
Do you need to remove the screen and risk getting dust inside there to swap this part?
Hi,
That's exactly the item, at that very same store. I also bought a loudspeaker as well as both back covers there. The audiojack is on board and I believe the flex cable has nothing to do with the screen type. The screen does not have to be removed.
I used those pics: http://www.ifixit.com/Teardown/Nexus-One-Teardown/1654/1
and this video: http://www.youtube.com/watch?v=cznogushN34&feature=player_embedded to figure out how to do it.
Basically, it's quite straight forward, given that you aren't a clumsy oaf ;-)
Remember the two rubber parts that might fall out when you pull off the mainboard assembly. (one at the bottom, for the microphon (http://guide-images.ifixit.net/igi/fpRmPyN6h12mtNvt.huge ,a bit to the left of the plastic tool) and one at the connector beside the sim card (http://guide-images.ifixit.net/igi/EOfeocuwhCRASB6M.huge , on the left part, somewhat down from the serial number sticker).
I have this probleme, but this part costs too much :S....
10. pin ON OFF way in board socket... u make jumper to on off buton
I have replace Power button for my N1. But you can reset your N1 by do'n need it. Except when you want flash rom!
Hi,
I have a Motorola Atrix and I'm afraid that the TRS connector socket in the phone has a loose contact. It got worse and worse the last days and now it doesn't work at all :-( It's not the earphones and unfortunately I'm out of warranty.
Does anybody have experience repairing those? Help would be very much appreciated!
Have you opened the phone to see if it's the connectors internals or it's connection to the board? If the issues is inside the connector then you can just find a replacement connector and a buddy with some soldering skills. If its the later then you will have to determine if there is board damages and reevaluate after that.
you can see it any good mechanics , and sure it will be right soon.
No need to replace, if its dirty, use some petrol or contact cleaner solution, dip an earbud in it, and use the buds to clean it,
If its loose, open the phone, use a small sharp needle to poke up the contacts ( the earphone jack usually got 4 contacts, or howmany u can see, that realy touches the earphones plug), u can access all of them via openings in the jack,( the jack got small holes in sides( three sides, which are not visible to external world, unless u open the device), via which u can insert small pins to poke the contacts.
Nb. Some contacts are made to touch each other( intended to determine if u had inserted a headphone or not) . Notice you dont damage its position. Also turn on the phone only after the solution u used (if any) completely dries out.
Patience, precession,examinations .... dnt forgot these. U can save a lot of money if u have these, else dont go for it.
Sent from my HTC HD2 using XDA App
I feel just dirty...
Hi y'all,
I opened the phone and made sure all the connectors touch the board. However, while doing this I realized there is a lot of dust on the bottom of the socket. I didn't see it initially because it was that much that it covered the whole bottom. I am pretty sure it was the dust.
Anyways it works perfect again. Thanks a lot for your help!