Database Users

Himalaya Parts

i have been searching here in Egypt for some parts i need to fix my PDA. i needed
1. the metal piece on the sync connector. {Shown Below}(this part is essential for the connector to be firm; without it; the connector will be lose and will cause the connetor to be disconnected from the borad!!!); offcourse this is really annoying. when ever i need to chrage the PDA; i put the battery in the auxilary slot located on the cradel (after i take a full backup ofcourse). when batteries are full; put them back; restore; set time/date. and so on.
2. Side slider button. (a very tiny part on the side the button used for volume leveling is broken) although it is not that important i can manage without it.
3. Speaker. (makes a really noisey sound when the PDA rings. i have tried to lower the volume but still noisey; i alos tried to clean the speaker).
yes it looks like the mainboard needs a replacement. i have also checked that metal part coating the sync connector is sold out on ebay. But could not find a complete mainboard. please if anyone has any ideas whatsoever please let me know i really need help. if anyone has a mainboard i can buy it.
Thank you...
Khaled

most likely all htc devices use std components
try getting hold of the part nr's and check around
http://rswww.com/cgi-bin/bv/rswww/home.do?cacheID=uknetscape&returningUser=N
like here
it would be insane if it had special parts and anybody would stock sparepart fro all devices or even some
really bad business unless that person charged more then a new pda was worth
of cause you can get a broken one and canabalise it for spares too

Wizard Repair Guide?! Mines Broken :(

Hey Guys,
Well, I'm a bit gutted really! I dropped my XDA Mini S on the floor with the charger in and the connector IN the phone has come apart from inside the phone. The little metal bit is practically hanging out. I'm wondering, if i were to take the phone apart could i re-connect the little part? (I have a soldering iron if thats as simple as its going to be?)
Just wondering if anyone had any guides on how to take the phone apart and take a look at whats wrong?
Any help would be so much appreciated!
Many Thanks,
Tom

The service manual is hosted on the ftp site.
ftp://ftp.xda-developers.com/Wizard/Docs_Tutorials/
Hope this helps.

I suspect you probably broke the socket off, but if you have a soldering iron, you might as well try to get a new mini USB connector to work with.

You might try Pocket PC Techs:
http://www.pocketpctechs.com/main~unit~UTStarcom_XV6700-554~area~repairs~item~REP-USBCON01~name~UTStarcom+XV6700+Mini+USB+Connector+Replacement+Service.htm
I rang them up about an issue I had (screen on the fritz) and they seemed pretty knowledgeable and helpful.
Alternatively there's a company I found today in the UK. I can't vouch if they're good or not.
http://www.xdarepairs.co.uk/home.asp
Good luck.

Well I also have an issue with my wizzard... the mini jack connector (of the handsfree) is a bit loose.
What I am saying is that it does have a good connection with the rest of the circuit and sometimes the sound of the speaker goes off, then I have to insert the habdsfree and tickle it a little bit until it has a good contact.
? have some basic soldering experience,do you think I should give it a try?

Given my device has been apart too many times for me to admit to I thought I'd crack it open to take a pic for you guys. Not sure if this pic will help for those wanting to do some soldering:
Very large pic: http://farm1.static.flickr.com/216/452691530_f47801708f_o.jpg
Excuse the dust.

Ah! That picture at the bottom is exactly what I needed. The metal but at the bottom (the big sqaure) has totally sheared off....bloody thing. Thanks so much for the info on the repair guides. I may give those repair guys a call if i can't get it to work myself.
Thanks alot you guys
As for you WizeMan, it all depends on if you wish to void your warrenty or not. At the end of the day, I installed WM6 on my device so O2 would give me the finger if i tryed to claim. If I'm honest, I'm getting an upgrade next month so I'm not to bothered if I balls it up! Would be nice if I got it working though....
Lemmie know how you get on

unlock k-jam
i read all your write about how to unlock k-jam device but after all i get this message:
Lock Status: 0000000000000000
SIMLock Code: █⌠═eי∟80Γ█Σ☻< δ♠
how can i get it from this .........

lironasseo said:
i read all your write about how to unlock k-jam device but after all i get this message:
Lock Status: 0000000000000000
SIMLock Code: █⌠═eי∟80Γ█Σ☻< δ♠
how can i get it from this .........
Click to expand...
Click to collapse
A little bit of a thread hijack but that means it is SIM unlocked.

Let me tell you my news, my friends.
I opened my Qtek 9100 and fixed two serious issues regarding this phone, using... sponge (the one we use to wash the dishes)
1. I put some into the stylus socket (from the thin space it has) and also
2. On the top of the mini jack socket so when i assembled the housing it blocked it from moving (2 of the contacts are no more soldered and i dint have a soldering iron at that time)
Anyway, both operation went ok and my phone is more than fully functioning. Now the stylus is hardly (in a good way) comming out (it first gets longer then comes out).
I wanted to do also the safe singal fix, but didnt find the photos to apply it correclty, so if someone has them, please give link. If you need any info about the "Sponge" Hacks, just post or pm

WizeMan said:
Let me tell you my news, my friends.
I opened my Qtek 9100 and fixed two serious issues regarding this phone, using... sponge (the one we use to wash the dishes)
1. I put some into the stylus socket (from the thin space it has) and also
2. On the top of the mini jack socket so when i assembled the housing it blocked it from moving (2 of the contacts are no more soldered and i dint have a soldering iron at that time)
Anyway, both operation went ok and my phone is more than fully functioning. Now the stylus is hardly (in a good way) comming out (it first gets longer then comes out).
I wanted to do also the safe singal fix, but didnt find the photos to apply it correclty, so if someone has them, please give link. If you need any info about the "Sponge" Hacks, just post or pm
Click to expand...
Click to collapse
I'm still trying to get the a new fascia and will probably shove an eraser bit into the stylus spring mechanism to ensure the defect never happens. Also how did you discover the break in the solder joints on the headphones jack? I have a funny situation where the left channel of the headphones doesn't work but I suspected the headphones (the plug has to be pulled at an angle to get any sound out of the left) but now I am thinking it may be the socket itself.
By the way the reception fix pic doesn't load for me either but I unless you truly need it, don't waste your time doing it; I always have all 4 bars and sometimes have 2 bars.

AsGF2MX said:
I'm still trying to get the a new fascia and will probably shove an eraser bit into the stylus spring mechanism to ensure the defect never happens. Also how did you discover the break in the solder joints on the headphones jack? I have a funny situation where the left channel of the headphones doesn't work but I suspected the headphones (the plug has to be pulled at an angle to get any sound out of the left) but now I am thinking it may be the socket itself.
By the way the reception fix pic doesn't load for me either but I unless you truly need it, don't waste your time doing it; I always have all 4 bars and sometimes have 2 bars.
Click to expand...
Click to collapse
Allright here is the deal.
1. I found out the break in the soldier joints when i opened it. I was really suspicious about it because when i inserted my headphone jack into the connector, i had problem with the contact; the connector was loose and it muted my phones speaker. When i disassembled the phone using the service manual i saw with my eyes that the the joins where f-ed up.
2. I dont really need the signal hack i just wanted to experiment, i have 2.25.11 cingular radio rom and its great.
Btw i suppose you should better use the sponge, because the rubber may wear off but not the sponge...

Thanks for the tip on the sponge. I am going to grab a used but allegedly "like new" body from eBay and also get one of those covers as well.

Here's the Shift disassembly guide

So I has some free time and the shift was laying around...
Anyway let's get down to business.
The first part of the guide will cover the basic disassembly tips you maybe need in order to open up the casing and maybe upgrade something.
You will need a T6 screwdriver. That's all..but if you want to disassemble the display you will also need a T5.
1 Start by removing the battery, stylus, any card, sim or whatever is attached onto your device.
2 The shift's screws location is shown here.
3 You will need to remove the 3 rubber caps in order to expose the upper screws. First I thought the middle one is a connector to an external antenna. Nope, it's a screw hole.
4 After you're done with the screws you will need to remove the keyboard in order to have acces to another screw underneath it. I've found out that removing the keyboard is a bit tricky. There are no screws holding it, you simply must pull it off. Carefull not to bend it too much and begin with the upper part.
5. Underneath the keyboard you will have to remove this screw and the ribbon like cable that connects the keyboard. In order to do this, pull upwards the white blocker (shown with the green arrow) then pull off the ribbon cable (red arrow).
6. Next comes the first ugly part. You should remove the back cover on your shift in order to expose it's motherboard. Begin by placing your fingernail on the right bottom corner (or the left - you choose) and go along all the cassing in order to separate the 2 pieces of casing. You may hear a lot of ugly noises, cracks and so on... it's pretty normal, just don't abuse the casing too much. By the way, keep the shift in "laptop" mode while you do this.
7. After you remove the back cover you should see something like this.

Carefull with the hard disk. There aren't any screws fixing it to the motherboard. It's simply ...placed there, the back cover will fix it back to it's position. Don't tilt the device or the hard disk may fall and could damage the connector cable (orange ribbon). Around the hard drive you may see a black rubber insertion that protects it from certain shocks.
I've heard some of you guys asking about the dimensions inside and the possibility to replace this hard drive with another one, more thicker. THERE IS SPACE INSIDE TO DO THAT.
The silver corner and the whole sides of the rubber casing is about 2-3 mm thick in the upper portion and just about the same underneath the hard disk. It's kind of soft thus you may insert a larger hard drive without problems.
(Someone asked about a 2.5 drive replacement into the shift -- NO way dude)
8 Next you will need to remove the aluminium radiator and the fan.
You have to remove the following screws:
Note that the far right screw is somewhere deeper and you may need to move the hard-drive a little to get acces to it.
9 After you remove the aluminium heatsync you should see something like this. If you want to remove the motherboard from the chassis you should also remove the marked screw.

You may remove the ram board but carefull. It seems pretty stuck in there you will need to use some force. Here's a photo with mine removed. The metallic piece in the lower part of the picture is the card reader's casing. The card reader is made by Panasonic.
In order to remove the card reader first unscrew it (it's the last screw i was talking about 2 pictures ago). There is a ribbon connecting it to the mainboard.
here is the card reader removed:
and here is it's ribbon connector:

Here is the GPS antenna. YEP it is here. I've seen simillar antennas on bluetooth GPS mouses. This one is properly connected and seems to be powered. HTC had some GPS in mind when it designed the Shift.
10 In order to continue the disassembly you must remove 2 screws located somewhere around this area. They are under the ribbon cable connecting the hard drive to the motherboard.
Be carefull around that area. The shift's motherboard is made of 2 pieces, apparently one for the x86 side (intel processor, GMA950 video, card reader etc) and another for the WM side. The 2 parts are linked via a connector that is secured by those 2 screws. YOU WILL NEED TO BE CAREFULL WHEN REASSEMBLING THE SHIFT. IF THAT CONNECTOR ISN'T ATTACHED PROPERLY YOU'RE IN FOR A LOT OF TROUBLE AHEAD (had mine... trust me).
Here are various components.
RED - Display side connector. This is the only connector linking the 2 sides.
BLUE - Keyboard connector.
GREEN - underneath that area lies the connector that links the 2 parts of the motherboard.
YELLOW - those cables go to the wireless antenna.
Here is the Shift's internal microphone. Like I've said, i didn't know it had one.
The mic is linked to the generic "WM side" of the motherboard. Actually it isn't that simple like wm side - x86 side but as I can see these 2 parts seem to be pretty well diferenciated. One side - x86 - heatsyncs, ram, hard drive... another side - WM, aluminium caps soldered over the chips (like in most phones) microphone, gsm/gps antenna. The WLAN module is also located there.

11 If you remove the motherboard you should see something like this. The arrow marks the position of the antenna block (like the one shown in the FCC pictures).
If you want to remove the display part from the rest of the body you have to remove these screws:
2 more of these are located on the left side. Also remove them. Then the display should come out easily. Carefull not to damage the ribbon connector.
.
12 If you want to dissasemble the display you have to remove the screws from it's back plate. It should also come out easily. You should see something like this:

The hinges that enable your display to tilt are located inside the display block. Here's a photo with one of them :

now some tips about how to do this process if you want to upgrade the shift.
BE CAREFULL. The Shift's motherboard seems pretty delicate. If you want to mess with the hard drive, first disconnect the cable from the HDD's end, then from the motherboard.
If you want to remove the RAM board, pull it off by using 2 fingers, 1 for each side. You will find that the module is firmly attached and woun't come out easily.
I don't recomand you remove or try to mess with that silver foil over the display's back (one of the last pictures). There's a jungle of connectors and wires underneath it and they are cought between 2 layers of that stuff. They can be easily damaged.
When reassembling the shift first start by connecting the small ribbon from the microfone to the motheboard, then connect the display's cable. You will find it more easily to maneuvre if the display is at halfway distance from the main body. Then connect the 2 screws that secure the connector between the 2 portions of the motherboard. ONCE AGAIN, CAREFULL TO HAVE THESE 2 SCREWS FIRMLY ATTACHED. In my first try, the connection wasn't good so when i powered on the shift, it started to make some scarry stuff with it's leds and display. No harm been done but it was pretty scarry. You may then reattach the rest of the screws in backwards order.
If you will want only to upgrade the HDD just stop at "removing the back cover" part. There's nothing more you need to do, you don't need to remove the motherboard and there's pretty much no risks involved. Just be carefull with the ribbon linking the HDD to the motherboard.
I heard some advices about some serials on the chips and such data. Yep, I did photos of these things too. I'll attach them also, tomorrow after I organise my list of findings and notes that I've made with those. I'll post them by category. However I didn't find much, most chips are imposible to read because of the faded markings and other ones are covered by aluminium caps that are soldered over them. The shift looks like a large phone.
Please ask questions if you have. I'll try to help and be specific on those topics.

Bravo!! Good job!!! Can't wait to see the remaining! Now we need someone to try upgrading the HHD. This is getting more interesting!

Excellent, thanks for sharing your findings.

Really good job, man!
Really good job! Thank you for this "step-by-step" guide!

now time to enable the microphone, enable the phone, and look like a complete idiot when u try to hold this thing up to your ear
now u pretty much proved a few things. this thing is pretty much a fully functional wm device. you also shower we were right all along the gps is very very possible for this device. i need to get ltxda one of the gps tools and have him post a lock so you can all see some gps action

Ok people, I'm willing to order a larger HD and even more RAM. I'm going to contact some of my sources on Monday or Tuesday. Any help you guys can provide would be great.
EDIT: Great job on the how-to here!!!

Pawel062 said:
now time to enable the microphone, enable the phone, and look like a complete idiot when u try to hold this thing up to your ear
now u pretty much proved a few things. this thing is pretty much a fully functional wm device. you also shower we were right all along the gps is very very possible for this device. i need to get ltxda one of the gps tools and have him post a lock so you can all see some gps action
Click to expand...
Click to collapse
Let's try this on Sunday afternoon bro if you're availabe. I also have a tool that i'm going to try to run, if the family allows, and provide results. Get with me sometime after 3pm. I'm headed to bed now...nite all.

Can you give some information about touchscreen model or manufactur???

I must first study how the protective silver film is attacked on the back of the display. from the fcc photos it seems there are a lot of ribbon connectors between it's twin layers. first time i've dissasembled shift i didn't have enought guts to rip that film in order to expose the internal components. Some connectors in that area caused me a lot of problems (shift's display didn't light up at all or the led's started to go crazy). I'll investigate the problem and there will be a second shift disassembly session in which time i wish to upgrade the hdd also.

So, where might we solder our 32GB SD card to the WM side?
Great job!

Keyboard
Hello,
I tried to pull out the KEyboard by it doesn't work.
What is the Secret to get it out ?

i've sent you an email.

facdemol said:
i've sent you an email.
Click to expand...
Click to collapse
Thanks for the Email, I'll try it on Monday and let you know if it work.
Andi

Possible Mistake If You Choose A 2,5 Hhd For Shift Original Hdd.
facdemol said:
I've heard some of you guys asking about the dimensions inside and the possibility to replace this hard drive with another one, more thicker. THERE IS SPACE INSIDE TO DO THAT.
(Someone asked about a 2.5 drive replacement into the shift -- NO way dude)
Click to expand...
Click to collapse
Thanks to everybody for the help to dissasenble.
Im sorry, It´s clear is not possible.
I'd attach a Picture of my shift with a 1.8 + 2,5" hdd.
---------------------------- -----------------------------
Please, don´t buy ANY HDD 2,5" Noone will fit in.
Is necesary a 1.8" HDD AND the conector of the HDD MUST BE a kind of ZIF connector. (They Called "LIF")
(Neither there are COMPATIBILITY with IDE/ATA/SATA connectors. You will need a ATA 7 conector!!!)
I found this kind HDDs in 80, 100 and 120 GB capacity, easy to buy ad least in Spain.
For Myself I'd ordered a Toshiba-MK1214GAH (120GB), where I Plan to Install a Personal Ed. XP + Vista in a second partition.
Armas.

How difficult is to take apart an HTC Ozone?

Hi all,
My wife spilled a glass of beer on my PDA, and now the top front buttons don't react like before. Sometimes you don't hear the 'click' and you can feel like they got stuck.
The keyboard looks fine, so the problem is only the with the top buttons at the front of the PDA.
Have anybody tried to take apart this PDA? Would be easy to open it and clean everything before putting everything back?
Thanks a lot

I completely soaked my Ozone about a week after I got it... knocked it in the sink. I like to think that I was among the first to void my warranty, Lo..l?
The phone is really well constructed for what you need to do. All of the critical electronics are very well shielded on the board, nothing difficult about separating the board from the case.
Six 'star drive' screws on the case (that's where the warranty sticker is), one tiny phillips on the board - board pulls up off of pins, away from the usb connector and Bob's your uncle. The keypad is not fastened to the case, pull it right out.
Watch the ribbon cable for the lcd - I would not recommend disconnecting it. there should be enough play to allow you to work. Make sure you're working in a really clean environment, and check the inside of the plastic lcd cover obsessively right before reassembly. If you're anything like me that one little catpet fiber or cat hair or whatever the hell will drive you to take the phone apart again 4 days later...
Sorry about the ramble... it's late. Short answer is: Nothing to it.
Good luck!

Thanks a lot for your post. It was really helpful.
I will probably try it this weekend.
I'll post here the results
Cheers

So if I wanted to buy a different color keypad (dont like the green) it shouldnt be hard to take apart??...I change screens in Env/Voyagers a bit so have a little knowledge...

[Q] Not charging unless I put upward pressure on USB cable

Hello everyone,
Since a few days my phone doesn't charge unless I hold the cable up and in the left or right corner of the port.
If I just stick it in, it doesn't connect/charge at all. And sometimes it says it's charging, but it isn't at all (or it's losing more power than it's receiving because it doesn't have good contact with the port).
Is there any fix to this or does anyone else have this problem?
It is NOT a problem with my micro-USB cable, I tried many, they all act the same.

Bad news
You have to replace your USB port, there's no doubt about, unfortunately!:crying:
Edit: there's a little chance to solve this by cleaning up your USB port...

i had this and it turned out to be dirt ground into the bottom of the USB port. A thin piece of wire from a tie wrap sorted it.
(of course, usually it IS a faulty USB port)

samsamuel said:
i had this and it turned out to be dirt ground into the bottom of the USB port. A thin piece of wire from a tie wrap sorted it.
(of course, usually it IS a faulty USB port)
Click to expand...
Click to collapse
I suppose this is a stand for what I said:highfive:?!

hehe,. yea, , only to begin with i was countering your 'theres no doubt' remark, , but then realised i hadn't read your whole post.

Well guys, I tried cleaning. A layer of dust came of so I got excited, but it didn't work.
There also is way too much play with the cable when it's in, so yeah.
How much is that port change going to cost me?

from what I've read its not so much the price as the difficulty, , there are loads of stories of repair shops screwing it up. If you're a dab hand with a soldering iron, give it a go, or if you go to a repair shop, get down in writing what they are gonna do if they screw it up.

Yet again a good advice!
I wouldn't suggest to do it your self unless you're a soldering master: as samuel suggested there are (so called) profesionals failing to do this, just because it's tricky enough to get the job done the right way.:fingers-crossed:

Sometimes it is possible to resolve by tightening up the connector in a fashion that promotes the contact of the female to male contacts.
Done one dismantled once as easy to work on connector, basically I pushed the shorter edge in just slightly & with CARE on the female socket in the area over the contact plate thus forcing the male plug to push tighter against the contacts, also tweaked the to plug retention lugs so plug clips tightly.
Worth trying as if lucky can be a cheap easy solution & has worked fine on one I did but as only done the 1 I have no idea if it going to work for majority of worn plugs :-S
Replacing board socket is tricky & not that cheap normally as a good tech knows it a not liked or easy repair ... good luck

Thanks for the great advice everyone, I really appreciate it.
Mister B said:
Sometimes it is possible to resolve by tightening up the connector in a fashion that promotes the contact of the female to male contacts.
Done one dismantled once as easy to work on connector, basically I pushed the shorter edge in just slightly & with CARE on the female socket in the area over the contact plate thus forcing the male plug to push tighter against the contacts, also tweaked the to plug retention lugs so plug clips tightly.
Worth trying as if lucky can be a cheap easy solution & has worked fine on one I did but as only done the 1 I have no idea if it going to work for majority of worn plugs :-S
Replacing board socket is tricky & not that cheap normally as a good tech knows it a not liked or easy repair ... good luck
Click to expand...
Click to collapse
I'm going to try this first, if it doesn't work, I'll follow samsamuel's advice.
I love this community!

Unscrewed said:
Thanks for the great advice everyone, I really appreciate it.
I'm going to try this first, if it doesn't work, I'll follow samsamuel's advice.
I love this community!
Click to expand...
Click to collapse
May take couple of adjustment to get it good & best do a little at a time.
Will only work if is contact issue between plugs, if issue is broken contact leg or poor connector leg solder joint to mainboard then no benefit.
Post back if get it working ...

Mister B said:
May take couple of adjustment to get it good & best do a little at a time.
Will only work if is contact issue between plugs, if issue is broken contact leg or poor connector leg solder joint to mainboard then no benefit.
Post back if get it working ...
Click to expand...
Click to collapse
Sure thing! I have one question, though. How do I correctly open up the device without damaging it (too much)?

Torx screwdriver and a thin credit card, there break down videos on youtube.

As above really, do your homework on stripdown & take a lot of care, back cover is easy if done right, plectrum is useful plastic tool for prying things apart or get hold of decent plastic opening tools, credit card can be used but too thick really.