So I bought a new housing for my O2 XDA II Mini, during the removal of the display ribbon I broke the little black part on the display connector which holds the ribbon down, and after hours of trying to get the ribbon back in and secured I have bent the pins in the connector to buggery.
The ribbon appears to be untouched, however the connector which the display ribbon goes into is broken.
Is there anywhere I can get hold of one of these little connectors to replace my broken one, obviously very sensitive soldering will be needed to remove the old one and solder the new one in place.
Alternatively, does anyone know any mobile phone repair shops in Auckland, New Zealand who would be able to help out with my situation?
I fear all i'm going to hear back is "the motherboard needs to be replaced", however I am determined not to go through this route, as I am a poor student and the phone sounds as if it functions fine, makes the beepy noise when first starting up on the setup screen.
I was very careful with the actual screen unit while removing it, and I have had signs of life earlier on in the broken connector episode, however I can no longer get anything showing as I can't fit the cable in.
Cheers for any help.
Anything would be appreciated.
"obviously very sensitive soldering will be needed"
And that only can be done by machines/robots. I don't think humans are even able to sloder those kind of connections...
But, could you post a picture? cause I might have suggestions on how to fix it. One would be to bend back the pins on the tiny slot with a toothpick and when done to tape the flatcable, so it stays there.
I've maybe got a spare creen for you.
g0atNZ said:
So I bought a new housing for my O2 XDA II Mini, during the removal of the display ribbon I broke the little black part on the display connector which holds the ribbon down, and after hours of trying to get the ribbon back in and secured I have bent the pins in the connector to buggery.
The ribbon appears to be untouched, however the connector which the display ribbon goes into is broken.
Is there anywhere I can get hold of one of these little connectors to replace my broken one, obviously very sensitive soldering will be needed to remove the old one and solder the new one in place.
Alternatively, does anyone know any mobile phone repair shops in Auckland, New Zealand who would be able to help out with my situation?
I fear all i'm going to hear back is "the motherboard needs to be replaced", however I am determined not to go through this route, as I am a poor student and the phone sounds as if it functions fine, makes the beepy noise when first starting up on the setup screen.
I was very careful with the actual screen unit while removing it, and I have had signs of life earlier on in the broken connector episode, however I can no longer get anything showing as I can't fit the cable in.
Cheers for any help.
Anything would be appreciated.
Click to expand...
Click to collapse
Hi, I've still got a SPV 500 and a MDA Compact, need to find it if you want you can have my MDA Compact screen.
Just PM if you are interested.
Related
anyone know how/where to get an xda mini II repaired? i'm in italy, but i can careless where it has to go. I'm at the point where i would rather just sell the device for it's workable parts (if there are any)...Today the screen has done a myraid of interesting things...anywhere from blank to thousands of vertical lines....ugh...
ohh yeah...warranty is void....or is time to just move on?
ok...no answers so i thought i would add some images ...anyone seen this before?
Mate i had a similar **** up a while back ...I did a HR and it worked fine..for me it was caused by a Overclocking software [Dnt want to Name it ]
If this dnt work try the Batt out and back in trick
Call ur Local service Center...
mine looks exactly teh same! but it happened after i tried to replace my housing, i screwed up the little gold prongs where the ribbon connector from the lcd plugs in...****! any ideas on how to fix? im the us so service center isnt really an option, and id ont want to send it off.
hi i had the same problem with my magicians, after i changed the housing. i found the problem with my device was that i had not plugged the screen back in properly. all i did was to ensure that it was pushed in properly before i clipped it back in
Menappi -
I had the exact same issue. I reopened the casing WITHOUT disconnecting any cables. I flipped the screen's ribbon black lock up, while maintaining pressure on the ribbon so that it does not pop out. When the black lock lifted, the preasure of my finger moved the ribbon further in . I pushed the black lock down, reassembled the device and ... PRESTO!! the screen works perfectly... and chumps on the bard advised to buy a new screen!!
Good luck
Hi All,
seems, you have problem somewhere in display connector. However, sometimes I see similar picture on physically broken displays, let's imagine, you were careful ad didn't use a hammer during housing replacement.
There are two possibilities: at first - try to remove and re-insert display cable (I hope, you know. how brown lock works). If there is no success - try again. At second - some wire on flat cable may be damaged. Sometimes, good technician with soldering iron can fix it, sometimes not. And if you used force, removing cable, board connector may be damaged too. However, only the experienced man can find it easily.
So, try to carefuly re-insert display cable. Try several times. If you are unsuccessful, you, for sure, need an experienced technician to fix your device.
I hope, you are not enough mad to send device for repair to Russia
I managed to take my Hermes apart and replace my Touchscreen. When i detached the touchscreen I had to take these orange connectors off, they were held in place with see through tape. One for the touchscreen about 1 cm wide and another one (my guess is the backlight ?!). I did so and i think maybe a bit to rough/unhandy. I replaced the Touchscreen and tried to connect those orange connectors again with some tape. Put my whole phone together again. Now I do not have backlight anymore and my touchscreen is not working... I think some pieces of the connection of the orange connectors stayed on the phone and some on the connector itself so it cannot make contact anymore...
What is the way to reconnect those orange "connectors"? Maybe it needs soldering?
On the picture you can see one of them.
I'm guessing you may have just screwed it... Unless anyone else knows different?
Damage to flex cable
If you have brocken the flex cxable on the touch screen you can find a new one on ebay at this link http://cgi.ebay.com/NEW-Dopod-CHT-9...ryZ41343QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
My Hermes has been suffering from screen whitening for couple of weeks, when it one day stayed all white. I've taken apart my Hermes and reconnected all connectors I've seen, including D-Pad connector, tightening and loosening the screws. Nothing worked... What should I buy? Do you think that the actual screen may be faulty? Or maybe the flex is damaged and I should buy it?
gregorysl said:
My Hermes has been suffering from screen whitening for couple of weeks, when it one day stayed all white. I've taken apart my Hermes and reconnected all connectors I've seen, including D-Pad connector, tightening and loosening the screws. Nothing worked... What should I buy? Do you think that the actual screen may be faulty? Or maybe the flex is damaged and I should buy it?
Click to expand...
Click to collapse
I have been reluctant to answer this, because there is no guaranteed answer. You have tested and reset the connector, but did you try placing some padding on the d-pad chip - to push it more firmly against the d-pad board. It has been quite successful for some members here. It is thought that a common cause of the white screen is a poor connection on the chip.
You could try getting a new d-pad board or a part from a second hand device that does not suffer from the white screen problem. If you know someone with the correct equipment you could also try re-flowing the solder on the board.
But I would say that a new board is not guaranteed to solve the problem as it is still possible that the flex cable may be faulty (or it's connector.
Mike
First of all, thanks for answer.
Yes, I've tried pushing it harder. Also I unpluged D-Pad and tried to turn on- still white screen. Unfortunately, I don't have access to any spare parts of this phone.
I bought Flex cable on ebay and IT WORKED!!! Yay, but now I'm experiencing some problems with usb connection
In the process of replacing my lcm, I managed to tear the button flex cable that connects to the mainboard.
I am currently looking for a the button flex replacement. What is the best way of tracking something like this down without going to HTC?
If there is no current seller/merchant available...Um...Is anyone selling an HTC HD2 for parts!?!?!?
Pics included...You can see the button strip, and the little 45 degree angle break on the flex..SUCKS!
I saw the break... Man, that's bad luck...
I hope you find a new button strip. The only other solution would be to solder fine wires from the point I highlighted on the photo. But that is very very very difficult... If you decide to do so until you find a new button strip I would recommend you to let an expert solder it, for example a television-technician. That shouldn't cost you more than a bier for the technician!
Wish you luck!
This just in, I have since purchased a broken hd2 and replaced the button strip. It has a light adhesive and is mounted on two small plastic posts on either end. To loosen the adhesive, just apply gentle heat (blow dryer) and GENTLY peel off. You might come across a stubborn part and want to give it a harsh tug, but you need to methodically peel it up using some sort of flat piece to get from underneath it.
Another torn flex Anyone has spare one or knows where can I get it?
I'm sorry but can't help. I get parts for iPAQs from iPAQ Repairs in the UK. I'm surprised there isn't something similar for HTC parts.
I'm interested in what an 'lcm' is. I've seen it mentioned but with no description.
i need one of these too. i hate htc's policy in not selling parts directly.
This button board should only be like upto $40 usd.
im needing a main board charger soxet broke if price is right ill sell
I have the same problem ....you solved?
where did you buy?
Hi
I got a keypad PCB on eBay... But it was very expensive
Found it http://cgi.ebay.com/Flex-Cable-Keyboard-PCB-HTC-HD2-T8585-HD-II-2-Leo-/320562469094
please how we can solder this wires
please how we can solder this wires
dvdaio said:
please how we can solder this wires
Click to expand...
Click to collapse
You should be a good electronic technician or know a good one. Otherwise I advice you not to try. I am a ordinary technician and I can say that in my case it was very very difficult and even if I tried hard, I wasn't able fix all connections. Only two of my buttons work right now.
How to Replace Button Strip?
Anyone know of a link showing how to replace this strip? Either I can't find key words for a search or there aren't any good videos out there. - thanks
Good to hear I'm not the only one to snap it so easily. Ordered a replacement from e-bay.
Sorry to dig up an old post but, I need that little wire that connects the wifi/bluetooth module to the main board. I replaced the digitizer in my phone and I somehow jacked up one of the ends on the cable. Anyone out there have parts?
Just bought a new screen for a cracked hd2 and hit some problems. Firstly, its a uk hd2, so it was a solder connection, i bought the screen + digi from ebay and noticed it was a ribbon connection (not sure if that will make a difference). When undoing these plastic clips
http://imgur.com/Faiyig3
Both broke. They were so brittle, has anybody seen/heard of a way to fix this? I put it all back together and the screen does come on, but touch doesnt work.
Can anybody tell me what these cables do? Is one for touch, what about the other?
Gutted about my hd2, its been going so well all these years...is it fixable?
Not good :-/
those 2 clips: one is the flex ribbon connector & other is the LCD ribbon connector.
The ribbon from LCD also is feed for digitizer.
Not sure if the locking arms are replaceable by themselves ! will look at an old mainboard & see.
you may get some function by bending a very light V in the ribbon so point of v is ribbon contact face & thus pushes tighter in socket promoting better contact.
putting a bit of tape on back may help too! be careful though as actual socket is very fragile too ...
Mister B said:
Not good :-/
those 2 clips: one is the flex ribbon connector & other is the LCD ribbon connector.
The ribbon from LCD also is feed for digitizer.
Not sure if the locking arms are replaceable by themselves ! will look at an old mainboard & see.
you may get some function by bending a very light V in the ribbon so point of v is ribbon contact face & thus pushes tighter in socket promoting better contact.
putting a bit of tape on back may help too! be careful though as actual socket is very fragile too ...
Click to expand...
Click to collapse
Tell me about it, thanks for explaining what the ribbon connectors do...I couldn't understand why the screen would turn on if the connector was broke. That's a good idea about slightly bending the cable, I will try that tomorrow afternoon. If i could swap them out, that would be awesome.
Thanks for answering, I appreciate you talking time to help a fellow hd2 fan!
Have made none working digitizer work via creating very light v shape bend in middle of contact area (bending across width of cable)
Do be gentle though ... not sure how successful it will be without clamp though :-/
fracmo2000 said:
Just bought a new screen for a cracked hd2 and hit some problems. Firstly, its a uk hd2, so it was a solder connection, i bought the screen + digi from ebay and noticed it was a ribbon connection (not sure if that will make a difference). When undoing these plastic clips
http://imgur.com/Faiyig3
Both broke. They were so brittle, has anybody seen/heard of a way to fix this? I put it all back together and the screen does come on, but touch doesnt work.
Can anybody tell me what these cables do? Is one for touch, what about the other?
Gutted about my hd2, its been going so well all these years...is it fixable?
Click to expand...
Click to collapse
how did they break? i'm going to attempt this myself soon and would appreciate any advice on getting the clips open safely.