In the process of replacing my lcm, I managed to tear the button flex cable that connects to the mainboard.
I am currently looking for a the button flex replacement. What is the best way of tracking something like this down without going to HTC?
If there is no current seller/merchant available...Um...Is anyone selling an HTC HD2 for parts!?!?!?
Pics included...You can see the button strip, and the little 45 degree angle break on the flex..SUCKS!
I saw the break... Man, that's bad luck...
I hope you find a new button strip. The only other solution would be to solder fine wires from the point I highlighted on the photo. But that is very very very difficult... If you decide to do so until you find a new button strip I would recommend you to let an expert solder it, for example a television-technician. That shouldn't cost you more than a bier for the technician!
Wish you luck!
This just in, I have since purchased a broken hd2 and replaced the button strip. It has a light adhesive and is mounted on two small plastic posts on either end. To loosen the adhesive, just apply gentle heat (blow dryer) and GENTLY peel off. You might come across a stubborn part and want to give it a harsh tug, but you need to methodically peel it up using some sort of flat piece to get from underneath it.
Another torn flex Anyone has spare one or knows where can I get it?
I'm sorry but can't help. I get parts for iPAQs from iPAQ Repairs in the UK. I'm surprised there isn't something similar for HTC parts.
I'm interested in what an 'lcm' is. I've seen it mentioned but with no description.
i need one of these too. i hate htc's policy in not selling parts directly.
This button board should only be like upto $40 usd.
im needing a main board charger soxet broke if price is right ill sell
I have the same problem ....you solved?
where did you buy?
Hi
I got a keypad PCB on eBay... But it was very expensive
Found it http://cgi.ebay.com/Flex-Cable-Keyboard-PCB-HTC-HD2-T8585-HD-II-2-Leo-/320562469094
please how we can solder this wires
please how we can solder this wires
dvdaio said:
please how we can solder this wires
Click to expand...
Click to collapse
You should be a good electronic technician or know a good one. Otherwise I advice you not to try. I am a ordinary technician and I can say that in my case it was very very difficult and even if I tried hard, I wasn't able fix all connections. Only two of my buttons work right now.
How to Replace Button Strip?
Anyone know of a link showing how to replace this strip? Either I can't find key words for a search or there aren't any good videos out there. - thanks
Good to hear I'm not the only one to snap it so easily. Ordered a replacement from e-bay.
Sorry to dig up an old post but, I need that little wire that connects the wifi/bluetooth module to the main board. I replaced the digitizer in my phone and I somehow jacked up one of the ends on the cable. Anyone out there have parts?
Related
So I bought a new housing for my O2 XDA II Mini, during the removal of the display ribbon I broke the little black part on the display connector which holds the ribbon down, and after hours of trying to get the ribbon back in and secured I have bent the pins in the connector to buggery.
The ribbon appears to be untouched, however the connector which the display ribbon goes into is broken.
Is there anywhere I can get hold of one of these little connectors to replace my broken one, obviously very sensitive soldering will be needed to remove the old one and solder the new one in place.
Alternatively, does anyone know any mobile phone repair shops in Auckland, New Zealand who would be able to help out with my situation?
I fear all i'm going to hear back is "the motherboard needs to be replaced", however I am determined not to go through this route, as I am a poor student and the phone sounds as if it functions fine, makes the beepy noise when first starting up on the setup screen.
I was very careful with the actual screen unit while removing it, and I have had signs of life earlier on in the broken connector episode, however I can no longer get anything showing as I can't fit the cable in.
Cheers for any help.
Anything would be appreciated.
"obviously very sensitive soldering will be needed"
And that only can be done by machines/robots. I don't think humans are even able to sloder those kind of connections...
But, could you post a picture? cause I might have suggestions on how to fix it. One would be to bend back the pins on the tiny slot with a toothpick and when done to tape the flatcable, so it stays there.
I've maybe got a spare creen for you.
g0atNZ said:
So I bought a new housing for my O2 XDA II Mini, during the removal of the display ribbon I broke the little black part on the display connector which holds the ribbon down, and after hours of trying to get the ribbon back in and secured I have bent the pins in the connector to buggery.
The ribbon appears to be untouched, however the connector which the display ribbon goes into is broken.
Is there anywhere I can get hold of one of these little connectors to replace my broken one, obviously very sensitive soldering will be needed to remove the old one and solder the new one in place.
Alternatively, does anyone know any mobile phone repair shops in Auckland, New Zealand who would be able to help out with my situation?
I fear all i'm going to hear back is "the motherboard needs to be replaced", however I am determined not to go through this route, as I am a poor student and the phone sounds as if it functions fine, makes the beepy noise when first starting up on the setup screen.
I was very careful with the actual screen unit while removing it, and I have had signs of life earlier on in the broken connector episode, however I can no longer get anything showing as I can't fit the cable in.
Cheers for any help.
Anything would be appreciated.
Click to expand...
Click to collapse
Hi, I've still got a SPV 500 and a MDA Compact, need to find it if you want you can have my MDA Compact screen.
Just PM if you are interested.
In the middle of disassembling my Legend to replace a bad digitizer, I broke the ribbon cable connecting the power button to the PCB. I haven't reassembled it yet, but I can't see how it's going to work.
img710.imageshack.us/img710/6929/brokenn.jpg
img137.imageshack.us/img137/1346/powerkz.jpg
(Sorry I can't post links because of post count.)
If anyone knows what the best way to repair this would be, I would be most appreciative. Thank you.
EDIT:
It seems this is the piece I need to replace.
tinyurl.com/28a7t9u
tinyurl.com/36yj5tw
Anyone know where I could go about finding one of these? The part number turns up nothing on Google.
I would find a service center and ask there, or I would solder it , it's just two wires....
But be sure you purchase a part with the ribbon cable on it, what I've seen it didn't look like it was there...
Good luck...
Called HTC service center. Unfortunately they don't sell parts direct.
I thought about soldering it, however the ribbon broke so close to the base that I am not sure I would be able to get access to the conductor.
Anyone have a trashed Legend that I could buy for parts?
So this just started off as a DIY digitizer replacement for me...but my MT4g is pretty beatup so I ordered some new housing from ebay to bring it back to life. The housing didn't come with buttons (mainly camera, power, volume buttons). I knew this and wasn't bothered because I planned to recycle the buttons from the old housing. Here comes my problem. The front buttons (home key/track button) are easy enough to replace. But upon closer inspection of the side buttons, I was at a loss about how to safely remove them. Originally I thought I'd be able to pop them out of the plastic pins with a small flathead or safe pry, but concluded that these were not coming out this way without damaging any hope of using these buttons in the new housing.
The plastic pins without the buttons in place look like this:
l__no.button__l
But with the button, the tops of the pins have been melted down holding them in place looking like this:
T___button___T
So I come to you guys asking for help about this. Is there any method of removing these and still be able to re-use them? Also include what tools I may need. Thanks in advance
First thing you need to get the right Housing For T-Mobile Mytouch 4g. The housing products in ebay are incomplete and can't satisfy your needs.
So go to alibaba.com you will get all the parts needed. Just follow this link.
Now you need to know all about how to fix it properly. The Repair Universe will guide you in this.
Screen Repair Guide
Touch Screen Assembly Guide
Hope this will help you to deal with the problems.......
Don't forget to hit the thanks button.......
I replaced my digitizer and lcd screen but i made a mistake while at it.
I need a new wire but I have no idea what it is for, so I can't search on where to buy it.
It's the longest wire and I think it is the antenna because I can't scan for a wifi or get any data running.
It plugs in to a small circular plug both ways. There are two smaller ones (black and white) right next to the vibrator.
Can anyone help me out???
Indeed, sounds like WiFi antenna.
Just my luck.. Already did a search and I can't find anywhere that sells that piece.
Does anyone know where I can find it?
You tried soldering, if possible? Sometimes full housings on ebay come with pieces like that.
I have never soldered before and I would give it a try if someone told me what to buy... I don't want to mess it up then have to buy a full housing
Just bought a new screen for a cracked hd2 and hit some problems. Firstly, its a uk hd2, so it was a solder connection, i bought the screen + digi from ebay and noticed it was a ribbon connection (not sure if that will make a difference). When undoing these plastic clips
http://imgur.com/Faiyig3
Both broke. They were so brittle, has anybody seen/heard of a way to fix this? I put it all back together and the screen does come on, but touch doesnt work.
Can anybody tell me what these cables do? Is one for touch, what about the other?
Gutted about my hd2, its been going so well all these years...is it fixable?
Not good :-/
those 2 clips: one is the flex ribbon connector & other is the LCD ribbon connector.
The ribbon from LCD also is feed for digitizer.
Not sure if the locking arms are replaceable by themselves ! will look at an old mainboard & see.
you may get some function by bending a very light V in the ribbon so point of v is ribbon contact face & thus pushes tighter in socket promoting better contact.
putting a bit of tape on back may help too! be careful though as actual socket is very fragile too ...
Mister B said:
Not good :-/
those 2 clips: one is the flex ribbon connector & other is the LCD ribbon connector.
The ribbon from LCD also is feed for digitizer.
Not sure if the locking arms are replaceable by themselves ! will look at an old mainboard & see.
you may get some function by bending a very light V in the ribbon so point of v is ribbon contact face & thus pushes tighter in socket promoting better contact.
putting a bit of tape on back may help too! be careful though as actual socket is very fragile too ...
Click to expand...
Click to collapse
Tell me about it, thanks for explaining what the ribbon connectors do...I couldn't understand why the screen would turn on if the connector was broke. That's a good idea about slightly bending the cable, I will try that tomorrow afternoon. If i could swap them out, that would be awesome.
Thanks for answering, I appreciate you talking time to help a fellow hd2 fan!
Have made none working digitizer work via creating very light v shape bend in middle of contact area (bending across width of cable)
Do be gentle though ... not sure how successful it will be without clamp though :-/
fracmo2000 said:
Just bought a new screen for a cracked hd2 and hit some problems. Firstly, its a uk hd2, so it was a solder connection, i bought the screen + digi from ebay and noticed it was a ribbon connection (not sure if that will make a difference). When undoing these plastic clips
http://imgur.com/Faiyig3
Both broke. They were so brittle, has anybody seen/heard of a way to fix this? I put it all back together and the screen does come on, but touch doesnt work.
Can anybody tell me what these cables do? Is one for touch, what about the other?
Gutted about my hd2, its been going so well all these years...is it fixable?
Click to expand...
Click to collapse
how did they break? i'm going to attempt this myself soon and would appreciate any advice on getting the clips open safely.