i wwant install aku3.2 lsw rom
so i downgrade with RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship-NoVendorID
it was ok i do a reset software and now my phone block on a black screen (dopod,spl,ipl)
thanks for your help
To solve your problem I would download the origirnal Qtek ROM and then do the following:
What you need to do is the following:
1) Switch on the mobile
2) Connect it to USB
3) While stuck on the Dopod splash screen, press the Comm Manager button (lower one on the left) and while pressing it push the soft reset button.
4) DO NOT release the comm manager button until you see the boot loader screen (full of colours)/. This takes approx. 5 secs.
5) When in bootloader screen, start the ROM update that you downloaded from the Qtek website (executable).
6) This will start the normal ROM flash program
7) Enjoy!
thanks
wich rom ?
because my phone is a qtek s200
i put dopod rom ? qtek rom ?
thankssssssssssssssssssssssssssssssssssssssss
foufou55 said:
thanks
wich rom ?
because my phone is a qtek s200
i put dopod rom ? qtek rom ?
thankssssssssssssssssssssssssssssssssssssssss
Click to expand...
Click to collapse
I would suggest you put the Qtek ROM back.
Related
hello all,
i'm a newscommer on this forum,i've trust in upgrade my phone with aku3
i correctly followed the topic , install step 1 (forG3) and step 2
my device worked fine after the first install (qteck 2.15 fr ->2.2 from step1)
i've synchronize my phone, and run the second part, installing without problems, reboot > freeze on the boot screen htc
no way to synchronize again. my phone is reconized by mtty (1.51 and 1.50) but i don't know how to use it
ipl 2.09
spl 2.20.0000
gsm 02.47.21
os 3.0.0.0
i've tried all the night to find a solution on all forum i knew, i drive me to this one, i think it could help me best ( you'r pro dudes )
but i'm allways stick. i've call htc division hotline (i'm from france) , they said i have to send back my phone ( but he's now out of waranty, cause it's not a legal rom i've installed, so i have to paid, and i've allready too much invest on my device)
plz said me there is still a hope!
did try upload another rom from bootloader ?
did try upload another rom from bootloader ?
but first try a hard-reset
i don't know how to load a rom from bootloader (i allready have made soft and hard reset
no one could help me ?
1. dowenload this latest Qtek official rom from here: ftp://xda:[email protected]_220734_2207114_024721_QtekWWE_Ship.exe
2. enter your S200 into bootloader mode by pressing power +camera + reset, let go of the reset, but keep holding power + camera until the three colur screen will show up (that is bootloader mode).
3. connect the S200 to your pc (make sure your battery is fully charged)
4. run the Qtek official rom.
5. good luck!
i've tried those kind of upgrade several time, but without possibility of establishing an active sync connexion, it's impossible to launch the rom install...
does samebody knew if it's possible to make a rom dump with an emulator and copy it on a sd card for autoinstall backup in bootloader mode ?
while in bootloader you don't need to establish any activesync connection. just plug the usb cable, then if appears "usb" on phone you are good to go.
install the original DOPOD rom from the ftp.
this rom don't work, it give me the message
error 294 invalid vendor id
it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much
pti_nourson said:
it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much
Click to expand...
Click to collapse
So you can now change your signature again, right
Hi people,
I have a mayor problem. I just fu*ked up my phone by installing WM6.
Now the screen freezes when the QTEK "Keep the world in one" logo is visible with the OS Version information. Hard reset wont work.
How can I restore the original rom ?
Please help me!
s200 off
and I have this problem. my phone is off by installing new spl
Now the screen freezes when the QTEK "Keep the world in one" logo is visible with the OS Version information. Hard reset wont work.
How can I restore the original rom ?
Please help me
To go in the boot loader screen you have to:
press & hold camera and commmanager button
press the softreset hole
release the commmanager button and keep hold the camera button until the 3 colours display appear
Byez
but wat can i do after i hav the 3 colour screen come out?
pls help..... i'm very nervous..... i don wanna waste my money coz i screw up my phone.,...
i'm now outstation... can go back to the service center within this 6 mth....
Connect USB Cable. Go in the Boot Loader screen (Hold down camera button, power button and soft reset until the 3 colours display appear). Run Rom upgrade Software.
mrsurya2000 said:
Connect USB Cable. Go in the Boot Loader screen (Hold down camera button, power button and soft reset until the 3 colours display appear). Run Rom upgrade Software.
Click to expand...
Click to collapse
Which rom upgrade software ?
de.schurk said:
Which rom upgrade software ?
Click to expand...
Click to collapse
http://www.romupdate.ru/ghjibdrblkz...rophet_220734_2207114_024721_QtekWWE_Ship.exe --> this software
don't worry, your device isn't bricked as long as you can run it in bootloader
check in WIKI if you have G3 or G4 Prophet
I'm the exact same situation.
And wiki didn't help so far...
Take it easy and flash the ROM as described. Use any WM5 ROM compatible with your device, but preferrably one with no vendor ID. In case you cannot update normally use the RUU-No-Vendor-ID application found in the FTP.
As said above the device is not dead, it can be recovered.
namco said:
Take it easy and flash the ROM as described. Use any WM5 ROM compatible with your device, but preferrably one with no vendor ID. In case you cannot update normally use the RUU-No-Vendor-ID application found in the FTP.
As said above the device is not dead, it can be recovered.
Click to expand...
Click to collapse
Bear with me on the dumb questions
It looks like I managed to re-install
Thank you for your help. I installed the rom dezzer advised (post 7 of this thread) and it worked fine. Does that mean tha NOW i can flash smart1 1.3's?
Yep. Turn off the phone, make it sync with activesync and run UPDATE_ROM.bat.
Then cross your fingers Kidding. It will surely work. Remember to hard-reset after the upgrade.
If anything goes wrong just reflash WM5 and hard-reset. Always hard-reset after ANY OS upgrade.
hi all ..
I did flash my HTC wizard with new rom after finishing the install the device reboot and stacked on the boot screen then I tried to go to the boot screen but I couldn't , I tried to make hard rest but also I coudn't nothing is working even charing the device cant be made .
bye bye
Are you able to get to a multi-colored screen with numbers?
In case you don't know, to get to the bootloader screen hold down the camera button and press the power button.
now i got the same problem.
I updated the rom & now i have the multi-colored (red/green/blue/white) screen
with RUU - IPL 2.18 - SPL 2.18 - USB on it (Qtek 9100)
I downloaded the tools from Vippie in the thread "How to flash a new ROM to your Wizard... a little tutorial!" but those won't help...
anybody got any advice? I would like to install WM6...
thanks in advance!
Hi,
Il from Belgium. SORRY FOR MY BAD ENGLISH
I have a Qtek S100
R 1.01.00
G 133.38
D 1.03.02 FRE ( French i think )
I tryd to change my Extended Rom from French to Dutch or English... with some file i dont know... im new it this stuff and i F**kt it up!!!
My Qtek just goene black and on the screen u can see USB 1.0.0
After open the baterycover and plug in back the qtek starts BUT after starting install the original app. it goes back to thr BLACK screen and nothing happens.
If I plug in the USB and connect it with my pc, it comes on the screen USB 1.0.0 ....
SO PLA HELP ME PLS!!!
I tryd hard / soft reset, NOTHING!
I look at XDA alredy 4 days everyday 4-6 hours I tryd SO MUCH, I take a day off work, so to can fix it!
IM GOIN CRAZY PEOPLE!!! PLS PLS HELP ME!
Best thing to do is go to bootloader mode and installing a new flash.
Bootloader mode can be found on the forum, but to help you out:
press simultaniously: camera button + power + soft reset (last one with the stylus)
Then start the rom update on your pc (do not use this from vista it wont work (or you have to find the fix online..)
Easiest way is to flash from windows xp works like a charm.
I have the same problem than rocky_gent but I can get the bootloader mode
i'm stack in bootloader mode ! And when i connect the usb cable doesn't display the "USB" but insists with "Serial V1.00".
I want to upgrade my rom from a secure digital (sd) cause i don't have another choice!
I 've been surfing through forums but i only found how to make an sd to upgrade your phone when you have an mda or xda (.nb1 files) . Qtek's roms have .nbf files !!! So i'm looking instructions to make an upgrade sd card with .nbf files (Qtek , Htc Magician) and not .nb1 (Xda)!!
http://forum.xda-developers.com/attachment.php?attachmentid=24569&d=1127232848
?
where can i get new flash? and yes im with vista, why it wount work???
hey guys, over the past few days ive had battery problems with my iMate JAMin, i got a new battery, insert it, and power on my device, now, rather than loading up the iMate image, it goes to the tri-color boot screen, i've tried a Soft and Hard reset, no luck , any one willing to try and help solve this problem, please email or PM: [email protected]
Will installing a new rom fix this problem?
Aidenkidd.
From the wiki:
wiki said:
If during an upgrade your Prophet fails to start properly or can only enter bootloader follow this:
Recovery
Download and install the latest version of ActiveSync (Google for it)
Download and unzip an AKU2.2 (No Vendor) ROM for the Prophet-any AKU 2.2 will do-from
here (any part one) or
here
Within ActiveSync DISABLE connect through USB (Tools->Connection Settings->Uncheck Allow Connect through USB)
Put the Prophet into bootloader mode (hold the camera button and insert the stylus into the larger hole next to the power socket)
Plug the Prophet in via USB
Run the RUU specific to your device (G3 or G4) from the AKU2.2 folder
Disconnect the Prophet, and then re-enable the connect through USB.
Your Prophet should now work!
Click to expand...
Click to collapse
I wrote it any way, but since no one reads it I may as well post it here.