hey guys, over the past few days ive had battery problems with my iMate JAMin, i got a new battery, insert it, and power on my device, now, rather than loading up the iMate image, it goes to the tri-color boot screen, i've tried a Soft and Hard reset, no luck , any one willing to try and help solve this problem, please email or PM: [email protected]
Will installing a new rom fix this problem?
Aidenkidd.
From the wiki:
wiki said:
If during an upgrade your Prophet fails to start properly or can only enter bootloader follow this:
Recovery
Download and install the latest version of ActiveSync (Google for it)
Download and unzip an AKU2.2 (No Vendor) ROM for the Prophet-any AKU 2.2 will do-from
here (any part one) or
here
Within ActiveSync DISABLE connect through USB (Tools->Connection Settings->Uncheck Allow Connect through USB)
Put the Prophet into bootloader mode (hold the camera button and insert the stylus into the larger hole next to the power socket)
Plug the Prophet in via USB
Run the RUU specific to your device (G3 or G4) from the AKU2.2 folder
Disconnect the Prophet, and then re-enable the connect through USB.
Your Prophet should now work!
Click to expand...
Click to collapse
I wrote it any way, but since no one reads it I may as well post it here.
Related
I have just installed SPB Clone correct on my Vario. Now this program did a soft-reset and the Vario just hang on de first bootscreen. (The one with the soft-/firmware version on it.)
SPB Clone has installed a program that would startup at first program while booting. My Vario don't seem to like that.
Is there a way to remove this program/problem without a Hard-reset. I don't like to lose my data.
I had the same problem..
you can only erase all data by installin the rom on top.
boot in USB mode, Hold the camera button and the reset pin and it will start in tree color mode, USB
Than install a rom from the computer... about 10 min.
A.
Do you have more information about that, what it does and how it works.
1) Fist you will have to find a rom update or corrent version of your phone.
I don't know what you have K-Jam or qtek 9100..
K-jam rom you can find at the support site, club i-mate
Qtek:
http://www.beyondthetech.com/blogs/kjam/2005/11/qtek-9100-rom-available-for-download.html
2) Boot the phone in USB Mode: Hold camera batton on the side and with the pen into the reset hole. USB screen will come up.
3) plug USB cable into computer, and run downloaded software.
10 more minutes and reset phone, all done....
Good luck
Clone is very dissapointing, I am using Sunny Backup Manager 3.7 now!
i had this problem too after installing SPB pucket plus. do you have this installed? if so just goto the options and uncheck safe mode and it should boot fine now, obviously wont help you until you have wiped the machine, but it will avoid the same problem again
Just tried to upgrade my S200 with a 9100 ROM ver 2.8.7.1 WWE (by mistake of course) and I can't turn it on anymore. Somehow it didn't even warn about wrong ROM.
Tried to hardreset it but no luck. When I keep the camera button it goes to RGB only when connected to the charger.
When connected to PC, the red and blue leds keep flashing and my PC gives Error 260 when I try to revert back to the S200 RUU.
Does anyone know how to bring it back to life? Is there a way to boot it from SD card?
-
I-mate Jam
Qtek 9100
Qtek S200
Don't panic!
I did the same thing some time ago!
What you need to do is make sure that the battery is fully charged. (The flashing of the screen can be a result of the flat battery.) Unfortunately, it is not possible to charge the battery when the wrong ROM is installed, as the ROM obviously tells the Prophet how to charge.
Let's assume you have an okay battery.
1) Start the Prophet in Boot mode. This is done by pressing and holding the Camera button and then pressing the soft-reset button. Keep holding for about 7 seconds, and the coloured bands should appear.
2) Connect to PC using the UDB cable.
3) Run the correct ROM upgrade. You do not need to be paired with ActiveSync, as the update programs are intelligent.
4) If the update does not work (and it fails at 95%), then try again. If it still fails, try again and do a soft-reset mid-way through. This will kill the ROM upgrade and you should then be able to do it fine after that.
The really important thing is that the battery is charged before you do this. Unless anyone makes a USB cable that can charge AND connect to PC, then a fully charged battery is a must.
Let me know if this helped.
Check this Out
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!
Check this Out
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!
Re: Boot from SD?
zealerc said:
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!
Click to expand...
Click to collapse
I am a bit confused, does that mean that ALLOW USB CONNECTIONS has to be chacked or unchecked?
I did the same exact mistake. Now, my baterry is fully chaged (which I can check on another phone) but when I put it in S200 it shows that the battery has 0%. Conseqeuntly, when i unplug the power cord the phone dies. I have no way of running the new ROM on it. I tried running a bootable SD but it only installed part of the software. i read on this forum that such a thing happens and that one would need to run a full version ROM from a computer. So, how do I do it??? I am almost giving up all hope of ever making this phone work
Does anyone have a file to boot from SD and is it possible to run a full ROM from SD. Please help!
I recently bought a german QTEK S200 and upgraded to latest Dopod ROM that is available in ftp.
I used lokiwiz and awizard tools to return to an older JAMin ROM that did not work as you very well expect.
Than I realized that I am unable to hardreset or put the jamin in bootloader mode. I am sure that before ROM upgrading I was able to do so; but I am not sure when the problem started. I mean whether it happened before using above tools or not. I am able to upgrade with dopod ROM one after another that makes the device enter bootloader and hard reset afterwards but manually I can not.
The cam and conn man buttons and soft reset all work alone but not in combination. I tried to wait for 5 to 10 sec before I take the stylus out of the hole but nothing changed. Aso the exe file enterbootloader is under windows and when I click it the device enter bootloader. Any comments?
Also is there a chance to have a QTEK German ROM with AKU 1. If so I will try the assumed but not proven method to downgrade to a lower ROM with prophet (which worked with wizard with a custom ROM).
Cheers.
After flashing the same Dopod ROM one after another the device started to enter bootloader :shock: and after a few more flashing the device can be hard reset as well. 8) No need to tell that I very happy
Bootloader mode in PROFHET (JAMin,S200 etc)
Hi ppl.
I suggest you to use cradle with 5V (1A) original charger or give 5V voltage to device externally.
By the way: to get prophet in Bootloader mode u need to hold continuously Cam and Power buttons.But u should do this with 5V (1A) voltage.
Thats all.
Neither with USB cable nor with the external supply the device does not enter bootloader mode by your method.
Also known method (cam button + reset) does not work with external supply as well.
Unable To Hardrst And Put In Bootloader The Prophet
Im not sure if this helps anyway i assume you can get to the OS executing EnterBootloader from an SD card or device memory did take me to the tricolour screen. on an SPV M600
hello all,
i'm a newscommer on this forum,i've trust in upgrade my phone with aku3
i correctly followed the topic , install step 1 (forG3) and step 2
my device worked fine after the first install (qteck 2.15 fr ->2.2 from step1)
i've synchronize my phone, and run the second part, installing without problems, reboot > freeze on the boot screen htc
no way to synchronize again. my phone is reconized by mtty (1.51 and 1.50) but i don't know how to use it
ipl 2.09
spl 2.20.0000
gsm 02.47.21
os 3.0.0.0
i've tried all the night to find a solution on all forum i knew, i drive me to this one, i think it could help me best ( you'r pro dudes )
but i'm allways stick. i've call htc division hotline (i'm from france) , they said i have to send back my phone ( but he's now out of waranty, cause it's not a legal rom i've installed, so i have to paid, and i've allready too much invest on my device)
plz said me there is still a hope!
did try upload another rom from bootloader ?
did try upload another rom from bootloader ?
but first try a hard-reset
i don't know how to load a rom from bootloader (i allready have made soft and hard reset
no one could help me ?
1. dowenload this latest Qtek official rom from here: ftp://xda:[email protected]_220734_2207114_024721_QtekWWE_Ship.exe
2. enter your S200 into bootloader mode by pressing power +camera + reset, let go of the reset, but keep holding power + camera until the three colur screen will show up (that is bootloader mode).
3. connect the S200 to your pc (make sure your battery is fully charged)
4. run the Qtek official rom.
5. good luck!
i've tried those kind of upgrade several time, but without possibility of establishing an active sync connexion, it's impossible to launch the rom install...
does samebody knew if it's possible to make a rom dump with an emulator and copy it on a sd card for autoinstall backup in bootloader mode ?
while in bootloader you don't need to establish any activesync connection. just plug the usb cable, then if appears "usb" on phone you are good to go.
install the original DOPOD rom from the ftp.
this rom don't work, it give me the message
error 294 invalid vendor id
it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much
pti_nourson said:
it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much
Click to expand...
Click to collapse
So you can now change your signature again, right
Guys,
I ve just downloaded this http://rapidshare.com/files/21256078..._DUT_11500.rar romversion in the understanding that it was for the HTC 9000 PDA. There was a file called MaUpgradeUt_noID.exe which I let 'upgrade' my 9000. However, I think something very VERY big went wrong! A reset by pushing the 2 buttons and reset button on the back gives me the option 0 to reset but all I can see after that is a black screen which says USB at the top and at the bottom v1.00
What happened and is this the end of my PDA? Sync won t work anymore now since my PDA can t be detected by windows because I can t get in the PDA!!!
Is there something I can do??!!!
PLEASE HELP ME OUT!!!!
Edit/Delete Message
sounds like you're just in bootloader mode
I think you are in what's called bootloader mode. Read the wiki to check - the screen you are describing sounds normal to me you plug you device into the comp via usb (with sync over usb disabled in active sync) then install a new rom.
You really shouldn't have tried to flash your rom without reading some instructions first but I think that your device should be fine.
If you have already upgraded your rom just do a hard reset and select the option to reset.
Will this thread help?
http://forum.xda-developers.com/showthread.php?t=310056
I'm sorry, this is the thread I ment to link:
http://forum.xda-developers.com/showthread.php?t=310054
strangely enough I found out that I DID use a good version picked from this http://forum.xda-developers.com/showthread.php?t=298020 post. In this thread mwang gives a link to here http://buzzdev.net/index.php?option=com_phorum&Itemid=125&phorum_query=read,40,30486,30486#msg-30486 where I picked the dutch version. I than double clicked the MaUpgradeUt_noID.exe file and the software for upgrading started. When he was at 100% he said the the ROM update was completed and that I had to do a reset. So, I than pushed the three buttons (2x the - button and the reset button at the back of the 9000) but all I than see is the bootloader menu with USB and V1.00...........
Sorry for putting it in three sub forum, my fault, but the device is from my work so I don t want it to be screwed up!!!
sanderh said:
Sorry for putting it in three sub forum, my fault, but the device is from my work so I don t want it to be screwed up!!!
Click to expand...
Click to collapse
Rather late now, but if it's owned by your company for work, should you really be di**ing with it?
Solution to probl: Stuck in Bootloader
The one way of fixing your problems....you're officialy stuck in bootloader,
Here's the way to fix it:
1. Stop Activesync USB connection on your machine under connection settings.
2. Uni : Reboot Bootloader then Connect USB ( If your phone isn't in bootloader already..)
3. PC : Run mtty1.42.exe ( Download from XDA's ftp site or search the forums, I'm sure you'll find it.)
4. Choose USB in "Port" (Reconnect if can't find/reconglize USB and try remove sim and sd card)
5.1 Press Enter
5.2 USB> (This will show up)
6. Type: Set 14 0
7. Press Enter
8. Run your rom update again and it should flash this time.
did it start??
did it start?? ?
Hi. first post.
Have an o2 exec. Different brand same deice and none of the other methods worked but finally got it working. Using mtty1.42.exe it would not see usb connection and therefore could not go down that route.
I booted into the bootloader mode that says serial at the top and v1.00 at the bottom.
Connected to the pc and cant remember if i stopped wcescomm.exe or not but you can try both ways.
Then started Midget_1990_v1_0_PU10_WWE.exe rom and followed the instructions and voila.
Hope this helps someone.
"Using mtty1.42.exe it would not see usb connection"
You need to disable the usb connection of active sync under connection settings and then only mtty will pick up a usb connection..