Please help me make my Sandisk 256+wifi work on my XDA Mini.
All the time i want to enable the wifi i have to reset the deive then insert the card...after inserting the green light apperas but when i want to configure it byit's software by clicking on the antenna below the screen the device freezes so i have to eject the card then device backs to normal state.
Please help to have the latest driver or additional software and assist me to make it work..
Regards
ROM: 1.12 O2 Xda Mini
Hi:
I don't have one, but i went to www.sandisk.com and found this, before i bought the card:
http://www.sandisk.com/pdf/retail/wi-fi-sd-compatibility.pdf
Sorry mate, it is not compatible!
Only the version without memory..
Bye
Driver
It's compatible..cause in the list for MDA compact which is as same as XDAii Mini bith cards are compatible...
Still looking to find stable driver and solution
Regards
Mine Combination is working fine....
Using German 1.12 ROM and latest driver from sandisk.com
Stefan
Sorry you are right they are compatible! my mistake!
Good luck
Glad to hear at least one person can work with it..so how can i obtain your ROM?
Hi
I have the same problem a few weeks now.
Before it worked great no problems at all.
i have the latest drivers and using rom 1.11.00
Don't know what's happend why it doesn't work properly anymore.
grts leon
LumpiStefan said:
Mine Combination is working fine....
Using German 1.12 ROM and latest driver from sandisk.com
Stefan
Click to expand...
Click to collapse
You mean you don't have to reset your device for working with it?
will it be detected everytime you turn on your MDA?
Have it hanged ever?
So why mine doesn't work?
Hi
Remove the drivers from your PDA by going to start-> settings->system-> remove program. Select the entries for the Sandisk card and remove them. Soft reset your PDA and then try the drivers from the website for PPC 2003.
After the driver has been installed. Please do another soft reset of the PDA and then insert the card.
Here is the configuration that should be on your PDA. The bluetooth support should be disabled. Tap on the two arrows on the top of your PDA. go to settings-> click on connections and then the advanced tab. then Tap on the network card to connect to your access point (AP). AP browser will be grayed
out, This is normal as we didn't develop a utility for pocket pc 2003. Make sure you have the automatically connect to non-preferred network option checked. If there are no items listed in the wireless networks box you can add your AP by tapping on "Add new Setting" Type the network name for your wireless network. You can find this in the configuration of your router. After you enter the name make sure "connects to" is set to "The Internet" and then tap on the authentication Tab. If you are not using the wep key, you can uncheck the box for wep. If you are using it on your router make sure to set it exactly the way it appears on your AP. When you finished making all those changes please tap on OK that appears up at the top. IF your AP is on, and within the range, you should see connected next to it and the tower to the left of it will have a
blue ring around the top. If you see a red X on the tower and it shows unavailable you should check the following:
1-IS the AP on
2- Is it in range 3- are your settings correct.
Once you see the connected next to your AP you can tap ok twice and begin using your wireless access.
It works for me
Grts Leon
I have successfully connected with the Qtek 9100 AKU2 ROM (the latest stable ROM for HTC Wizard) to Cingular via Bluetooth and Mac OS X 10.4.6. Instructions:
1. Pair OSX and the phone. You might need to check the "any device" checkbox on OSX's pairing utility.
2. Verify to OSX that you do want to use that device as a modem (if you don't get that dialog, then you will need to create the Bluetooth connection yourself -- message me or leave a comment if you need instructions and I will reply to you).
3. RENAME the attached iPAQ-GSM.txt to plain iPAQ-GSM (remove the .txt extention using the Finder 'Get Info' dialog). Copy the file "iPaq-GSM" to your /Library/Modem Scripts/ folder. I modified the original script that was floating on the internet for a year now in order to work with Cingular (the original script wouldn't get a carrier signal with my phone -- it needed some small initialization changes).
4. Go to your System Preferences/Network/Bluetooth/. There enter the following:
Service Provider: Cingular
Account Name: [email protected] (case sensitive)
Password: CINGULAR1 (case sensitive)
Tel number: *99# (the *99***1# number that does work with other phones doesn't work with the HTC Wizard)
On PPP options uncheck "tcp header compression".
On the Modem tab uncheck both "enable error correction" and "wait for dial tone". From the modem drop-down menu select the iPaq-GSM modem script.
Then, click Apply and then open the "Internet Connect" application and select Bluetooth from there. Click "Connect" and you should now be connected on the net via Cingular GPRS/EDGE.
Alternatively, you can create a new networking bluetooth connection instead of using the generic bluetooth networking pref panel, but that involves a bit more work -- although I personally prefer it as I have over 8 phones and I need different networking connection names and settings for each, instead of using the default "Bluetooth" one. If you are on the same boat, IM me or leave a comment for more instructions.
Thanks
dude you just made my day. It works perfectly. Thank God for people smarter then me.
Unfortunately, in my AKU2 QTek ROM, the PPP server dies right after I disconnect from the Mac. I have to reboot the PocketPC before I can reconnect my Mac to GPRS.
If anyone knows more, please download the script above and tell us if there is a way to fix this.
more mac users
hey guys,
just wondering if you've been able to sync your MDA(Wizard) to your mac. and if so, how? also, any luck updating ROMS without a PC?
whalien
Hi Guys,
I'm really stumped here, i have been on the www for days trying to findout how to get my Atom to work as a BT Modem for my PC. I keep going round in circles trying to locate the file USBMDM.INF but can not find this file anywhere. I have followed links to advise that i need to start "Modem Link" from program files but then i need the USBMDM.INF file to go to the next step....at least i think i do???......... can anyone help me to set up my Atom as a modem for my Laptop PC??
Thanx for any assistance that you can give.
instruction:
XdaAtom_Wireless.zip
Without pictures the instruction look like follows:
XdaAtom – Wireless Modem via Bluetooth
a.) Pairing Devices
1. To turn on Bluetooth on your device. Tap Start --> Settings --> Connection --> Bluetooth
2. Check on "Turn on Bluetooth" and "Make this device discoverable to other devices"
3. Tap on "Devices" and tap on "New Partnership..." to search for bluetooth devices.
4. Select your computer name and tap on "Next" to pair the devices.
5. Key in Passkey (for example "0000") and tap "Next" to continue.
6. On your computer, key in the same Passkey and click "OK".
7. On your device, check on "Serial Port" and click "Finish"
8. A partnership will be created on your device. Tap "OK".
b.) Disable incoming beam files
1. on your device, tap on Start --> Settings --> Connections --> Beam. Untick "Receive all incoming beams" and tap "OK".
c.) Disable Microsoft Active sync on your computer.
1. On your PC, launch Microsoft Activesync. Click on File Connection Setting
2. Uncheck “Allow USB Connections” and “Allow connections to one of the following” then Click “OK”
3. Microsoft Activesync is disabled.
d.) Configuring Modem
1. On your computer, click on Start --> Control Panel --> Phone and Modem Options
2. Click on "Modem" tab and select "Bluetooth DUN Modem" then click on "Properties".
3. Select “Advanced” tab and type in Extra initialization commands and Click “OK”.
** Depending on which service you want to create a connection to, you have to use the appropriate APN name and replace the “internet”. You may want to refer to your operator or its web site for the APN names.
e.) Create a Dial-up Connection
1. on your computer, Start Control Panel Network Connection
2. Click on “Create a new connection”.
3. Open the "New Connection Wizard" in XP and select “Connect to Internet” and click “Next”.
4. Choose “Set up my connection manually” and click “Next”.
5. Select “Connect using a dial-up modem” and click “Next”.
6. Tick on “Bluetooth DUN Modem” only and click “Next”.
7. Type in any name for your connection and click “Next”.
8. Type in Phone Number “*99#” and click “Next”
9. Type in Username and Password required (if any) and click “Next” then “Finish”.
10. Press “Dial” to connect to your modem connection.
11. If everything worked fine, you should able to get connected.
** You may want to refer to your computer’s Bluetooth software manufacturer for more information regarding to the dialing method.
f.) Disconnect Wireless Modem
1. To disconnect the connection, right-click on the dial-up connection and click on "Disconnect"
Thanx for the detailed set-up instructions Kropotov!
I follwed to the letter but at this time I'm still unable to get it all to work. When i enable the PC dial up connection it activeate the Atom cos the back light come on abd the BT symbol in the PC system tray changes colour. However it does not want to get past this stage and no signs of the GPRS sybol coming on the PPC...........I know my GPRS APN is "NET" with user name being the operator and the password being "WAP" but still nothing working. I just don't know why it should be so hard to establish a link via BT or USB cable. It was easier to do on my old Nokia 6030 about 5 years ago than it is on my Atom!
Regards
Chris.
try to connect to GPRS using USB connection...
Can you go to internet from your Atom?
How do I know which COM port the ActiveSync is using......would it be COM1 by default? When i try to set up a DUN modem the only ports that i can see are all Bluetooth ports that i have created, I do nt get the choice for COM1.
I also found some instructions from O2 on how to set up an Xda II to act as a modem, in these instructions you set up a new standard modem on the PC, disable Activesync on the PC then deactivate "Receive all beams" on the PPC and then activate "Modem Link" on the PPC. Then when you plug in the PDA to the PC via USB cable the computer will detect new hard ware and try to install a drive, I have not been able to locate the required driver o the internet so can not get any further with this method. The driver is on the OEM CD supplied with the device and as I'm away from home i can not check if i have the driver on the CD that came with the Atom. The driver i called "HTC USB Modem".
angusc :wink:
http://www.rapidshare.ru/27257
Kropotov,
I can't figure out how to download the file from this site, sorry to be such a pain.
http://dl.rapidshare.ru/27257/99530/USBMDM.INF
Thanx again for your continued support and assistance but that link is not working for me at this time, i will try it again later to hopefully get to that file!!
give me your mail. I will send you
kropotov,
Thx for the file, i installed a new modem on my PC and then activated the "modem link" on my PPC and installed the driver when prompted, but alas still not working. I think it is to do with the assigned COM port for the modem on the PC, I can only seem to choosE COM 4, 9, 13, 14, 15 when installing the modem to PC. I would think that the Atom would be com port 1-3 as it is connected to one of my PC USB ports......
Will keep playing and let you know if I manage to get it to work......Thanx for all your help.
Request Modem Driver for O2 XDA Atom
Dear all, Please anyone send me the Bluetooth modem driver, I just lost my CD, also the USB modem driver for O2 XDA Atom thanks alot
Cipto
O2 Atom
Request for BT modem driver
Hi, I'm looking for BT modem driver (.inf) to install in PC.
I'm using O2 Atom and my PC is Dell Latitude D420.
Thanks in advance for any help.
XDA Atom usb driver
Hi,
I'd like to know if somebody can send for me the drivers for my XDA Atom, because I don't have the original CD.
Thanx
Alvaro
xda atom driver
Hi,
I just found the correct drive for XDA Atom in the internet:
http://files.pdamobiz.com/Tools/atom_usbmdm.rar
I hope it help....
Alvaro
Is it possibe to use the usb/bluetooth modem to receive incoming connections?
Thanks.
Jebril can you pls send the same driver for my h/s ....Thanx.
Serial Port not appearing while teaming
Hi
I followed the following steps:
1. To turn on Bluetooth on your device. Tap Start --> Settings --> Connection --> Bluetooth
2. Check on "Turn on Bluetooth" and "Make this device discoverable to other devices"
3. Tap on "Devices" and tap on "New Partnership..." to search for bluetooth devices.
4. Select your computer name and tap on "Next" to pair the devices.
5. Key in Passkey (for example "0000") and tap "Next" to continue.
6. On your computer, key in the same Passkey and click "OK".
7. On your device, check on "Serial Port" and click "Finish"
My O2 Atom is not showing any serial port to select
any idea?
Regards
kropotov said:
instruction:
XdaAtom_Wireless.zip
Click to expand...
Click to collapse
Good work mate, but still wait for the laptop to come
Hi,
i'm looking for the cab file of the "Connection Setup" Tool. It's for configure your pda for your provider. I hope someone can help me .)
Don't you mean "HTC Network Wizard" ?
Search on the forum with this nam you should find it
it is the same for me:
in my htc cruise / rom 0.96 light swtos I do not have Network Wizard 1.0xxx but Connection Setup 1.5
I am missing the autorun/autodetect functionality (no reg keys, menu option in the wizard not activated)
can anybody help?
Hi
I am using Elfin running with official WM6.1. There is no option of "Connect Via BT" in activeSync menu. In the connections tab also only 'USB option available.
Any help?
Can you create a BT partnership with your PC?
I have paired the device and pc. Even hands free services are working fine. In the Status tab of connections it shows activeSync - Connected. But there is no oprtion availabe in the Activesync tab menu "Connect via Bluetooth". Previously, when i was using WM6, there was a option in the Activesync. Is there any problem in WM6.1?
Thanks in advance for your help
try checking at http://forum.xda-developers.com/showthread.php?t=530327
maybe it can help you
After Uninstalling of BTools app and Soft reset , It works.
Thanks.