bluetooth license expiration problem - Networking

Hi,
I have problem with PDA ACER n50 and with bluetooth activation.
The problem appeared after ROM upgrading from v1.00.09 to v1.00.18
New ROM was downloaded from official ACER ftp.
Description of problem:
----------------------
When I turn ON bluetooth I got after some seconds message:
Sorry! Bluetooth can no longer be used because the license is expired.
BDA: 00:00:00:00:00:00
Key: E3E534E1...
PDA System info:
----------------
OS version: v4.21
ROM revision date: 20050818
ROM version: v1.00.18
Firmware version: v0.94
Bootloader version: v1.13
bluetooth info:
Bluetooth for Windows CE
BT-PPC Version 1.7.0 Build 1900
My unsuccessful efforts:
-----------------------
soft reset
hard reset
change of system datetime
older bluetooth versions application
- Widcomm 1.4.1.59
- Broadcom 1.6.0 0600
registry modifications
I tried solve this problem from suggestions which I detected on this site
etc...
Can anybody help me with specific recommendation ?

i'd contact acer
otherwise you can prob get it running if you set your clock a few years back :S

Related

HELP!! Bluetooth Active Sync for Mini XDA

I cant sync with bluetooth. Please help
make sure you have the latest rom since this seems to be most stable when doing AS over BT.
On Desktop
1) make sure bt dongle is inserted and all software have been properly installed
2) open Activesync click File>Connection Settings... check Allow serial or infrared connection to this COM port:
3) Indicate your BT COM PORT check your BT software or documentation mine uses COM5, this maybe diff on your desktop.
On PPC
1) Tap Start>Settings>System>Bluetooth Setting
2) Under Bluetooth ActiveSync Setup: tap Start you will be taken to the Bluetooth screen. Make sure both boxes are checked.
3) Under Devices Tab. Tap New your ppc will now search for your desktop.
4) type your passkey and wait for the Desktop to prompt you for a password. Type this password on the desktop to finish bonding.
5) open ActiveSync tap Tools>Connect via Bluetooth and you're done.
I did this but I can't connect still.
Here is my rom:
ROM version: 1.03.00 WWE
ROM date: 11/01/04
Radio version: 1.01.00
Protocol version: 1337.38
ExtROM version: 1.03.166 WWE
your ROM looks old. isn't there a new ROM for O2mini? I suggest you get the latest ROM. anyway with your current ROM it can still be done but it is a bit tri ckier. You can read a step by step how to here http://www.howardforums.com/showthread.php?s=&threadid=544932
sorry for the ignorance. I went to the O2 site and there are no new rom for the mini.
Can you please tell where to get it?
Sorry I didn't know that just assumed O2 had released it since i-mate and qtek have released theirs. I use the i-mate JAM w/ Qtek 1.11WWE ROM. Anyway you can wait for O2's official ROM also or follow the link to HoFo that did the trick before my ROM updates.

Bluetooth Problem in Himalaya :(

Hello.
I have a big problem with my BT in MDA 2 ... When i do a hard reset, after start of WM2003SE BT icon have a red line on itself. When I tap this Icon I can see error message: "There is no Bluetooth hardware installed on this device." and every field is grey....
Is there a driver which can fix it ?
Regards, Bartek
/edit: I saw reply about registry fix, but i don't have any backup And I can't take this registry key ... Can sb help me ?
kijan said:
Hello.
I have a big problem with my BT in MDA 2 ... When i do a hard reset, after start of WM2003SE BT icon have a red line on itself. When I tap this Icon I can see error message: "There is no Bluetooth hardware installed on this device." and every field is grey....
Is there a driver which can fix it ?
Regards, Bartek
Click to expand...
Click to collapse
It seems that the BT driver wasn't loaded properly! Can you check?
Are you sure, you didn't change anything in the registry?
Which BT stack are you using?
Hi ... But can You tell me how can I check it ? I'm really "green" in MDA & PPC .. But BT don't work even I do a Hard Reset ... I've bought this model yesterday and I can't tell anything about it's history ...
kijan said:
Hi ... But can You tell me how can I check it ? I'm really "green" in MDA & PPC .. But BT don't work even I do a Hard Reset ... I've bought this model yesterday and I can't tell anything about it's history ...
Click to expand...
Click to collapse
Huch! This will be difficult indeed...
Ok, let's start!
1) Go in Settings/System, click on Device Information and give me what you have on the version tab.
2) Go In Windows directory and search for a file called ASIC5_BTUR.dll
OK.
1.Version:
ROM Version: 2.06.00WWE
ROM date: 06/14/04
Radio Version: 1.18.00
Protocol Version: 1337.38
ExtROM version : (blank)
2. Don't have this DLL
/sorry about time when I'm responding...
kijan said:
OK.
1.Version:
ROM Version: 2.06.00WWE
ROM date: 06/14/04
Radio Version: 1.18.00
Protocol Version: 1337.38
ExtROM version : (blank)
2. Don't have this DLL
/sorry about time when I'm responding...
Click to expand...
Click to collapse
If you use fileexplorer to show files, don't forget to select show all files option. then make a search on ASIC5_BTUR
If you don't have it, well you need to reinstall it or think about upgrading your pda to WM2005
Cheers,
.Fred

Frozen screen with Via Michelin 4.4 and BT 77 GPS

Hi everybody
Some posts ago I asked questions to find right parameters to connect with my BT 77 bluetooth GPS.
Using VisualGPSce I finally found COM5/38400 as parameters to connect with. Knowing that, I used Via Michelin 4.4 with those parameters and wait ...
Some minutes later I obtained the satellits signals in the GPS test screen of ViaMichelin but after that ViaMichelin got frozen.
I'm near the goal but something is missing.
Thanks for your help.
Appareil QTEK 2020
ROM 1.72.02FRA
RADIO : 1.14.00
PROTOCOLE : 1337.24
EXTROM : 1.72.603
Bluetooth driver Microsoft or Widcomm
I'ts me again
I tried to replace the Microsoft drivers by the Widcomm ones with a .cab found on the net.
1 : Delete of key HKLM\Services\BTIcon to uninstall Microsoft drivers
2 : Install of BluetoothGPS.cab to install Widcomm drivers
It has been great during one hour.
Via Michelin 4.4 was OK with my GPS BT77 on port 7
After that I got "Bttray : "the BT radio failed to turn on due to insufficient driver memory available" and "BTTrayCE BT could not be correctly initialized".
Of course memory is actualy not concerned.
Then it has been impossible to turn bluetooth ON without obtain the message "BTTrayCE BT could not be correctly initialized"
I think the .cab to install Widcomm was not good because during installation I got messages about the fact that e-PocketSetup was not a valid official version.
Is it possible to find a good installation for Widcomm drivers (or others) for Windows CE 2003 ?
The problem is this Microsoft driver for Bluetooth.
How to find another one ?
Thanks

Setting Tytn to 2G only after Rom upgrade. Now it will not connect to BES

I am hoping that you can help me out with a little situation that I may have created on my HTC Tytn.
I was using the original ROM that Shipped with my Tytn and I was experiencing a "slow" device with some audio problems while in calls. Yesterday, I decided to upgrade. I installed SPL-2.10.01ipro. as per the warnings on the page (thankful that I have not bricked my phone) Worked perfectly for allowing myself to upgrade to what I think on the downloads page was the most current "stable" rom. Currently my Tytn is running the download listed below.
Upgraded HTC English Qtek_001
Rom 2.11.255.1 03/07/07
Exp Rom 2.11.215.102
Radio 1.38.00.10
Protocol 32.71.7020.12H
OS Build 15673.3.3.1
AKU 3.3.1
SPL 1.11
HTC BOOT 108
I have to admit, the unit runs great. Problem though, on the old OS, I was able to, under phone "band" select "2G". The reason for this is the Blackberry Connect software that I need to run for my work. (Or else I get assimilated into the world of Blackberry handhelds) will not connect as 3G. I have currently set the unit to "auto" for network type ("GSM ,WCDMA) and "auto" for GSM/UMTS Band. Any time I try to change this to anything else the unit comes back with a "Warning" that it can't complete the change. The unit still will not connect and says "Not Connected" under the bb_connect ver 4 status page. I have tried to install the older Rom back to;
HTC English
CID Q-TEK_001
ROM 1.18.255.3 7/22/06
ExtRom 1.18.255.106
Radio 1.03.03.10
Protocol 32.34.7010.01H
OS Build 14955.2.3.0
AKU 2.3
SPL 1.11
HTC_BOOT 1.04
I'm not sure if I can keep the upgraded radio and Rom versions and simply change the OS version but when I try to change to the complete rom above I get an error (260): UPDATE ERROR
"The Update Utility cannot connect to your PDA Phone. Please Check your USB Cradle/Cable is connected properly between the PC and your PDA phone"
The connection is good as I have been using active sync to install things like the blackberry software.
I am spinning my wheels here. I thank you in advance for any assistance that you can provide.

ActiveSync 4.5

I've successfully upgraded my Qtek 9090 to WM6 Pro (5.2.16.20)
-
ROM version: 5.60.00 WWE
ROM date: 03/02/05
Radio version: 1.12.00
Protocol version: 1337.42
All works great, but still I can't connect to ActiveSync 4.5
When I put the Qtek 9090 on cradle it ask to install Activesync 4.5 or newer ... but I've installed (and reinstalled) this tool, downloaded directly from MS site.
I've also Updated all the components on PC (SO, Office, etc ..) with Microsoft Update. But still I've this problem.
Please, could you give me any help ?
Thanks in advance.
Beppe
-
i got the same problem!
my 9090 says:
cannot open the connection usb, this connection is no longer valid ore exist, plz select a diffrent
it worked until now
Sorry, my English is bad. But I try to help because I had the same problem.
Which firewall is installed?
With the change of WM2003 on WM6 new rules must be allocated for ActiveSync.
Several ports (999, 5678 etc.) must be switched free or turn the firewall off for testing!
Simply turning off the network monitor at the Comodo Firewall.
Good luck!
Mathias
My Qtek 9090 ask for Activesync 4.5 or newer while connecting.
I have just tried with another PC with XP on board and a fresh copy of Activesync 4.5 - Same problem (ask for 4.5 or newer)
I'm quite sure the problem is on PDA.
I hope in some suggestion.
Thanks to all.
Beppe
-
do search on the forum.. you'll find what you need..
cheers
evo
check\uncheck in USB to PC - Enable advanced network funkcionality try which one of them will work with your pc
RESOLVED !!! (Yeahhh)
The problem was on network properties of Qtek, when connected.
Right-click (in control-panel/network-connection) the Qtek entry / Then properties
- check only tcp/ip protocol and MS network services
- I've disabled bindings for VPN and packet-trace utility
Activesync 4.5 WORKS GREAT NOW
Have a nice WM6 upgrade.
Beppe
-

Categories

Resources