I've tried to make the reg-hack to activate file reception through bluetooth with OBEX but when I make the soft reset after ther registry mod, the key is again 0 (1 is enable).
Is it possible to activate the receive file profile in TyTN?
hi, I don't know if you are experiencing exactly the same problem as me or if yours is a slightly different issue, however I couldn't receive any files via bluetooth on my brand new Vario II. I could send, but I couldn't receive.
I opened up com2 as a new incoming port on my bluetooth settings and voila - suddenly it worked.
Don't ask me why!
Thank you MrLeoni for your reply.
I've done what you suggest but I still can't receive files through bluetooth.
I think that this is a basic feature in a PocketPC.
Any idea?
JmJ17 said:
I've tried to make the reg-hack to activate file reception through bluetooth with OBEX but when I make the soft reset after ther registry mod, the key is again 0 (1 is enable).
Is it possible to activate the receive file profile in TyTN?
Click to expand...
Click to collapse
did you try to check: start -> settings -> connections tab -> beam -> receive all incoming beams ?
worked with me, i don't need to do any reghack to receive files via BT.
Thank you very much eva_d.
Your suggestion works fine. The problem was that "receive all incoming beams" was disabled.
I used to disable this because I thought that when this is enabled, infrared receiver is working and wasting battery, so I used to disable.
After set this option, I've revised the reg-hack about OBEX and I've seen that is 1 (enabled), so the conclusion is that disabling "receive all incoming beams", OBEX is disabled.
Thank again to everyone who has help me. Problem solved.
Related
i have the i mate jasjar which is the mini laptop- idon't know what you call it guys-, anyways the problem is when a nokia phone tries to send somthing to me by bluetooth, it says (unable to connect), but i can send files to them easily..... so can any one help
click start / settings / connections
then click beam
tick receive all incoming beams
Regards
Sonywiz 8)
i thought beams were infra-red?
It is, but Receive all incoming beams needs to be switched on to receive files by Bluetooth as well for some stupid reason!
Fin
Hi,
Somebody please help me.
Iam not able to recieve any files from anyone using bluetooth. On the senders screen, it discovers my phone but if you send something, it says sending failed. Does this have anything to do with beam option? sometimes it works and sometimes it doesnt? Any resolutions..? I have my bluetooth on and on discoverable mode, i have unchecked the pass key option.Please help..
thanks/..
nishant
did you enable incomin connection?
IT is all about "Beams". You must be set up to receive Incoming Beams. I know it is confusing as we all assume that is related to InfraRed Beams, but "NO", it applies to Bluetooth as well.
But be warned, with Incoming Beams ticked, it can drain your battery, so I only switch it on when I need to receive a file.
Hi !!
I have just bought a O2 XDA mini and for some reason it just doesnt recieve data from other devices over bluetooth!
i can send ( i am paired correctly!!) data !! but cant recieve data!! the sending bluetooth device always says send failed ... or recieving bluetooth device ( i.e. my xda) is not responding!!!!
i am really getting :evil:
anyways i would realy appreciate some help!
i wonder if its something to do with the damn ports!!!
Same problems here. I have tried with Ipaq2210, SEk700i, Nok6230, Samsung600 all paired up ok but file transfer is never a discovered avilable service.
Sending fails whether initiated on wizard or other devices. I believe it is down to the Microsft bluetooth stack as the Ipaq uses widcomm stack and works with all the above phones.
I'm hoping someone will find a reg hack to improve the functionality.
What with no wifi activesync my recent upgrade from Ipaq and K700 to wizard is leaving me feeling cheated.
Al
go to start>settings>connections>beam, and make sure you tick the "receive all incoming beams" option.
i had this problem before and i couldn't recedive any file through bt, but when i checked this i receive anything now, and it shows the "file transfer" profile when i initiate the pairing from another device.
i hope this works for you guys.
cheers.
Many people have problems to receiving files via blutooth, howerver don´t have problems to send files.
I don´t no why but the solution is:
Definitions>Connections>Infrared
And here activate the "receive from every IR"
That´s all
AFAIK, you can receive files from PAIRED devices without "receive from every IR". If you set "receive from every IR", you will be able to recieve files from ANY device.
Due of safety reson I recommend always keep your device invisible (set off "Make this device discoverable...") unless you need to pair it with something, and keep BT off unless you have something connected.
hi guys, i've got an issue with my bluetooth in that i can't receive files, i've tried from 2 different computers and a phone with no success. my windows box gives me an obex error code 0x49 if thats any help to anyone. i've got accept transfers ticked and the devices are paired. i can send files from the phone fine so the bluetooth is defiantly working.
Turn beam on.
Receive all incoming beams.
could you clarify a bit? i've got accept all connections turned on and don't see any beam options in the bluetooth app?
In sense settings, go to all settings. (Right softkey).
Open the bluetooth settings and open the 1st tab.
Expand the advanced settings.
Open the file transfer config and click allow "incoming file transfer connections"
I've not tested it though
I reconfigured the comm manager to run this app, called BtManager.exe. More useful than the wizard it normally runs.
i've already done all that, everything is enabled in the bluetooth settings app i just can't receive files, as i said before i can send to devices and connect via a2dp so i don't think it's a hardware issue so there must be a software problem somewhere?
Tung_meister said:
hi guys, i've got an issue with my bluetooth in that i can't receive files, i've tried from 2 different computers and a phone with no success. my windows box gives me an obex error code 0x49 if thats any help to anyone. i've got accept transfers ticked and the devices are paired. i can send files from the phone fine so the bluetooth is defiantly working.
Click to expand...
Click to collapse
same here, any one experienced it and solved the problem?
Long time no reply on this thread. I fixed the problem for my HD2. Maybe it help poeple to fix their receive files for their HD2 too.
In bluetooth advanced settings go to file transfer and uncheck safe files on your sd card, instead set the path to your sd card for receiving files. Click finish and test.
Thanks Guido, that worked for me!