Hi,
Somebody please help me.
Iam not able to recieve any files from anyone using bluetooth. On the senders screen, it discovers my phone but if you send something, it says sending failed. Does this have anything to do with beam option? sometimes it works and sometimes it doesnt? Any resolutions..? I have my bluetooth on and on discoverable mode, i have unchecked the pass key option.Please help..
thanks/..
nishant
did you enable incomin connection?
IT is all about "Beams". You must be set up to receive Incoming Beams. I know it is confusing as we all assume that is related to InfraRed Beams, but "NO", it applies to Bluetooth as well.
But be warned, with Incoming Beams ticked, it can drain your battery, so I only switch it on when I need to receive a file.
Related
One confusing problem that i want to solve: When i am connected to the Internet via the "Wireless Modem" application,then i can't receive any incoming call even it is no data transfer over the air(GPRS). Every phone is available for receiving this calls when it is no data transfer active. But my Himalaya not. The other side is ringing to me but i can't see anything. No missed call no incall..nothing. I can lose lot of important calls when i use Internet(WModem) at same time. The problem is the same also for SMS's. Is it some solution of this problem? Or is it somewhere over the net any application that can toggle the call forward to any other phone? I will be greatful for any suggestion. Thanx.
i have the i mate jasjar which is the mini laptop- idon't know what you call it guys-, anyways the problem is when a nokia phone tries to send somthing to me by bluetooth, it says (unable to connect), but i can send files to them easily..... so can any one help
click start / settings / connections
then click beam
tick receive all incoming beams
Regards
Sonywiz 8)
i thought beams were infra-red?
It is, but Receive all incoming beams needs to be switched on to receive files by Bluetooth as well for some stupid reason!
Fin
Many people have problems to receiving files via blutooth, howerver don´t have problems to send files.
I don´t no why but the solution is:
Definitions>Connections>Infrared
And here activate the "receive from every IR"
That´s all
AFAIK, you can receive files from PAIRED devices without "receive from every IR". If you set "receive from every IR", you will be able to recieve files from ANY device.
Due of safety reson I recommend always keep your device invisible (set off "Make this device discoverable...") unless you need to pair it with something, and keep BT off unless you have something connected.
I've tried to make the reg-hack to activate file reception through bluetooth with OBEX but when I make the soft reset after ther registry mod, the key is again 0 (1 is enable).
Is it possible to activate the receive file profile in TyTN?
hi, I don't know if you are experiencing exactly the same problem as me or if yours is a slightly different issue, however I couldn't receive any files via bluetooth on my brand new Vario II. I could send, but I couldn't receive.
I opened up com2 as a new incoming port on my bluetooth settings and voila - suddenly it worked.
Don't ask me why!
Thank you MrLeoni for your reply.
I've done what you suggest but I still can't receive files through bluetooth.
I think that this is a basic feature in a PocketPC.
Any idea?
JmJ17 said:
I've tried to make the reg-hack to activate file reception through bluetooth with OBEX but when I make the soft reset after ther registry mod, the key is again 0 (1 is enable).
Is it possible to activate the receive file profile in TyTN?
Click to expand...
Click to collapse
did you try to check: start -> settings -> connections tab -> beam -> receive all incoming beams ?
worked with me, i don't need to do any reghack to receive files via BT.
Thank you very much eva_d.
Your suggestion works fine. The problem was that "receive all incoming beams" was disabled.
I used to disable this because I thought that when this is enabled, infrared receiver is working and wasting battery, so I used to disable.
After set this option, I've revised the reg-hack about OBEX and I've seen that is 1 (enabled), so the conclusion is that disabling "receive all incoming beams", OBEX is disabled.
Thank again to everyone who has help me. Problem solved.
Hi,
When I send a file to my HTC Hermes phone, it automatically receive the transfer. Is there a way to disable the automatic transfer? I want to have a warning before a device making a bluetooth connection.
Try: Start-Settings-connections-beam and uncheck 'Receive all incoming beams' not sure if this relates to just infra red or bluetooth and infra red though, let us know how you get on.