My O2 mini S is not responding at all after I tried to run a new English ROM (mine was german rom). I could not even turn it on. This means I could not also connect it to ActiveSync to update the English ROM. Nothing is responding, cannot go Bootload mode by holding camera and pressing rest. I cannot even charging the battery...
What should I do? Please help... Thank You...
hi
I don't now how to resolve your problem, but I'm also have the same O2, on
German offcourse and I'm planing to update with english rom. Witch rom you are used?
And maybe you are brouke him because it was Sim locked.
Sory for my english....
ppc_palm said:
My O2 mini S is not responding at all after I tried to run a new English ROM (mine was german rom). I could not even turn it on. This means I could not also connect it to ActiveSync to update the English ROM. Nothing is responding, cannot go Bootload mode by holding camera and pressing rest. I cannot even charging the battery...
What should I do? Please help... Thank You...
Click to expand...
Click to collapse
Did you try updating the rom not having a fully charged battery? It sounds like it to me - if it is completely dead i reckon the battery is dead. Connect it to the mains (not usb) charger for a while until it comes to life. If you have a spare battery handy try that.
Related
Dear all,
My O2 Mini is dead after the power when off during the course of recovering the data.
The screen is not lighted up although the phone is on. The only thing that is visible is "Serial" on the top and "Ver 1.0" at below of the screen. Tried everything but was not able to reflash my ROM and bring my phone back to life again.
Can any expert help me with this?
Please advise.
Waiting urgently.
Regards,
Ken
Did you try taking the battery out for several seconds to get it out of that mode?
That means your bootloader works then your fone aint dead, try doing this ...
Anansky's BigStorage ROM
Guys, i accidently upgrade my pda2 device with a BA rom.I use helmi's wm 6 rom for BA to my pda2 (alpine) it completed the flashing process. now it's dead! no charging light when i try to charge, non of the buttons work, nothing happen when i try to reset, hard reset or other combinations. is there any way to get it back? how can i enter the bootloader menu again?
croesus said:
Guys, i accidently upgrade my pda2 device with a BA rom.I use helmi's wm 6 rom for BA to my pda2 (alpine) it completed the flashing process. now it's dead! no charging light when i try to charge, non of the buttons work, nothing happen when i try to reset, hard reset or other combinations. is there any way to get it back? how can i enter the bootloader menu again?
Click to expand...
Click to collapse
there is no accidently u tried to update stupidly to wm6, there is no excuse for this, and you are now the proud owner of a totaly buggered pda.
serves you right realy, as if you read the forums, u will find there is no wm6 for the xda 2i, and the file you would have used will have stated that it was wm6, 1000%
there is no way of getting it back now... HAHAHAHAHAHAHA!
well unless u can plug it into your pc ang run the 2003se rom.
p.s. how stupid.
Hi!!! I Have the same problem but 1 difference I dont want to update anything ... My PDA was stop and I take out the batery and now is dead no light or system ... what can I DO? HELP ... When I plug in in my PC ... dont do anything
Could anyone can help me to solve No GSM poblem. I think there are many other users have same problem.
After it faild during update rom, My HP6915 represent NO GSM during booting and the phone funcation also doesn't work. But in HP Asset you can see it, just no firmware, no version number. I try to flash english radio rom and french radio rom, but always stop at 1%. This matter appeared after I flashed orange rom(french version). I think it locked by Orange.
Does any one can help us?
did you try the update with no sim and no minsd?
EREZYAD said:
did you try the update with no sim and no minsd?
Click to expand...
Click to collapse
Yes, I update without sim card and minisd. Always stop at 1%
to be on the safe side i will go over general insraction
battery full
recomended xp os & activesync 4.5 (not beta)
minsd & sim out
ac addapter connected (ac power from orig transformer)
hart reset your device before the update
connect device directly to computer's usb plug
run the update
try radio only &/or the all update you can also try on a different pc
if all didn't work read this and see if you can find somthing that works on the 6900
http://www.htcwizardweb.net/node/170
good luck
EREZYAD said:
to be on the safe side i will go over general insraction
battery full
recomended xp os & activesync 4.5 (not beta)
minsd & sim out
ac addapter connected (ac power from orig transformer)
hart reset your device before the update
connect device directly to computer's usb plug
run the update
try radio only &/or the all update you can also try on a different pc
if all didn't work read this and see if you can find somthing that works on the 6900
http://www.htcwizardweb.net/node/170
good luck
Click to expand...
Click to collapse
Thank you for your reply!
I tried but still same, stop at 1% when I flash Radio WAN OS, stop at 2% when I flash Radio FS. I tried to unlock simlock and CID unlock, but it doesn't work on my 6965
called a few places looks like the radio chip is fried. sorry man...not looking good.
try update again with this method
I got almost same problem. I tried to update GSM rom but update fail and my ipaq stuck at hp invent logo. try following steps to see if it works for you
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider
I also meet such question.
actualy. I met the same problem "No GSM" after wrong update. I thing I tried everything, but I Didn't try to flash the device via mini-sd card. I don't know the right address for GSM area. Did anyone know?
caoxt said:
I also meet such question.
Click to expand...
Click to collapse
COME ON guys some one can help us , i have too the same problem please help with radio stack !!!!!!!!!
me too,, really nedd help here.. my only phone sable...
how to fix my phone XDA mini PM10A dead
First off, you're a little vague on details, don't you think?
Second of all, you're phone is not a Charmer. It's a Magician; moving to the right place.
the phone not power.
any solution to check if hardware problem or software?
Are you saying that the battery isn't charging, or the unit itself isn't turning on?
Can you get it to go into the bootloader mode?
if you see "something" on the screen such as "USB Ver.1.1" , then its no fault at all.
you can simply flash a rom.
but if it doesn't charge (you don't even see the red light)
go! get it repaired, hardware has gone bad.
mariner_heart said:
if you see "something" on the screen such as "USB Ver.1.1" , then its no fault at all.
you can simply flash a rom.
Click to expand...
Click to collapse
My Magician, will not connect in the bootloader mode (dot detected by the RUU). Whenever I use the No_ID RUU, it keeps saying that the upgrade tool, isn't for my device (although it was downloaded from the official site).
Any suggestions?
hi
hi every bady.my xda o2 its on german language.how i can fixed on english language.
mariner_heart said:
if you see "something" on the screen such as "USB Ver.1.1" , then its no fault at all.
you can simply flash a rom.QUOTE]
Hi, can any1 explain to me what it means by "flash a rom"?
I'm having the same problem, my screen shows "USB Ver 1.0"
Please help
Click to expand...
Click to collapse
Plz help .... installed a wrong ROM for HTC HD2 on my T-Mobile HD2, now it stopped responding totally, no power, boatloader not showing, the orange led not working when connecting the charger.
Is there anyway i can fix that?
Thanks
Can you provide a link to the Rom?
Sent from my HTC Desire using XDA App
When you plug in the USB connector to the phone and computer and turn the phone on, does it power on?
If it does, then get into boot loader then flash an official tmo rom.
Madii said:
installed a wrong ROM.......................now it stopped responding totally, no power, boatloader not showing, the orange led not working when connecting the charger.
Click to expand...
Click to collapse
all signs that you flashed a rom containing a ..51.. radio.
options
1 - JTAG it. (expensive, tricky)
2 - warranty repair (dont mention flashing)
3 - paid repair (around $140 i believe)
Thank you for replying, but no it does not operate
Madii said:
Thank you for replying, but no it does not operate
Click to expand...
Click to collapse
Ok well it seems like a radio brick then, and since you don't feel like providing more info you should just stick with samual's 3 options. Good luck.
hd2 died
i also did the same thing to my phone i tryed to load a stock rom russia version and now my phone has no led when plugged in, wont turn on dont do anything. is there a fix for this????
raskalaaron said:
i also did the same thing to my phone i tryed to load a stock rom russia version and now my phone has no led when plugged in, wont turn on dont do anything. is there a fix for this????
Click to expand...
Click to collapse
Your options are in post 4. But like I previously stated, explaining your device version, ROM, SPL and flash method helps a little more to understand what type of brick it is.
hey man i did the same i instaled 1.66 rom in my t-mobile very dumb !!! but in the end after 2 weeks of searching i found service for it , if you still have the phone contact me
Madii said:
Plz help .... installed a wrong ROM for HTC HD2 on my T-Mobile HD2, now it stopped responding totally, no power, boatloader not showing, the orange led not working when connecting the charger.
Is there anyway i can fix that?
Thanks
Click to expand...
Click to collapse
where you are come form ?