Guys, i accidently upgrade my pda2 device with a BA rom.I use helmi's wm 6 rom for BA to my pda2 (alpine) it completed the flashing process. now it's dead! no charging light when i try to charge, non of the buttons work, nothing happen when i try to reset, hard reset or other combinations. is there any way to get it back? how can i enter the bootloader menu again?
croesus said:
Guys, i accidently upgrade my pda2 device with a BA rom.I use helmi's wm 6 rom for BA to my pda2 (alpine) it completed the flashing process. now it's dead! no charging light when i try to charge, non of the buttons work, nothing happen when i try to reset, hard reset or other combinations. is there any way to get it back? how can i enter the bootloader menu again?
Click to expand...
Click to collapse
there is no accidently u tried to update stupidly to wm6, there is no excuse for this, and you are now the proud owner of a totaly buggered pda.
serves you right realy, as if you read the forums, u will find there is no wm6 for the xda 2i, and the file you would have used will have stated that it was wm6, 1000%
there is no way of getting it back now... HAHAHAHAHAHAHA!
well unless u can plug it into your pc ang run the 2003se rom.
p.s. how stupid.
Hi!!! I Have the same problem but 1 difference I dont want to update anything ... My PDA was stop and I take out the batery and now is dead no light or system ... what can I DO? HELP ... When I plug in in my PC ... dont do anything
Related
Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...
I have serious problem with my PDA SPV M2000 after upgrade to WM6. After upgrade i try to restart my PDA with Hard Reset, but can see only 4 collored screen. I can acess only bootloader mode and nothing else... PLEASE HELP
reflash
Did you try a reflash?
I try all the steps 5 times but nothing. I try use WM6 from helmi and xpode. With the same resolution. Now i try to downgrade to WM2003...
I am back on WM2003. Thanx god
I got a gray screen whith serial v 2.07... and few pages i find dosent help me att all..... please help me some one....
brb66 said:
I got a gray screen whith serial v 2.07... and few pages i find dosent help me att all..... please help me some one....
Click to expand...
Click to collapse
the grey screen with serial v 2.07 is the bootloader mode...
maybe a reflash will do the trick...
how did you screw up the upgrading process? did you accidentally unpluged the cable? is it a corrupted file?
I have never experienced this, but, if i were you, I would reflash it. if nothing good come up,then maybe the file you are using to upgrade is corrupted...
hope this helps, and maybe the experts would have more ideas cause i am just a user.....
I've upgrade to WM6.0 pdaviet, but can't use GSM network : no services...
Any body help me plz...
fix it now, pdaviet'rom works well with 1.15.00 radio .
sorry for my English
Ibhave a tmobil MDA amd i did an upgrade to windows mobile 6 and now my MDA is slow in most of the programs also the SMS when inserting any messages the words do not show after at least 10 sec.
Please, definelly need help.
navarde
Have you performed HARD RESET?
What ROM did you use for flashing?
(also some installed programs may slow down your device a lot!)
I had the same problem. From time to time whem im flashing my phone its happening. After few soft resets it'll be ok.
my sp3i is stuck on the WM splashscreen and afther that it just turn off, i'v installed WM5 and then back to the original WM2003SE from imate but after a while it just begun to do that, plz help me.
does any one know how to make a reflashing throw SD? can anyone make a guide? plz helpme to revive my dear phone.
thanks in advance.
Your phone can be reflashed with Mtty even when it freeze on the boot screen cause its not necesary have the phone ON.
Tried to do a hard reset maybe is a windows registry problem.. after the hard reset the values on registry will be reset to default.
already done that, and doesnt work, even it reflashes through USB but afther reaching 100% the phone restarts and get stuck again in the same place, no matter if I hard Reset or reflash by USB the phone still get freeze.
can any one tell me how to delete all the data on the memory to make a clean reflash? or how do I reupload the firmware? is there a way to recover the phone?
remember I already install the WM5 and back to WM2003SE but after that the problem started, maybe i screw someting wile doing it?
Solaris_irc said:
my sp3i is stuck on the WM splashscreen and afther that it just turn off, i'v installed WM5 and then back to the original WM2003SE from imate but after a while it just begun to do that, plz help me.
does any one know how to make a reflashing throw SD? can anyone make a guide? plz helpme to revive my dear phone.
thanks in advance.
Click to expand...
Click to collapse
Tutorial for sd flash
Check here
well my phone after i flashed and installed wm 6.5 it was working totally fine, but this morning i turned it off and then on and it totally freezes at the startup screen and never loads windows. what i can do?
i'll appreciate any comments
i have then same problem switches on displays, disigned for windows mobile 6.5.5 then freezes
Yeah many ppl has this issue... be sure to flash first the att stripped att stock rom then hard reset then boots then reflash the custom rom then hardreset then try again to use th rom maybe it works ok now
I have the same problem
but I have the same problem. I bought a second hand phone and also freezes on the welcome screen and to make the rom? I need it so I can re-flash the windows
I have problem with my tytn, i was traying 7-8 rom of win mobile 6.1 or 6.5 but no help, my htrc cant find nework or when he find network he was online 1 hour and after hat he he offline in phpne mode, what is a problem, radio, rom or... ????
miljan017 said:
I have problem with my tytn, i was traying 7-8 rom of win mobile 6.1 or 6.5 but no help, my htrc cant find nework or when he find network he was online 1 hour and after hat he he offline in phpne mode, what is a problem, radio, rom or... ????
Click to expand...
Click to collapse
try to upgrade radio version on your device !! you can find Radio Rom Wizard in http://forum.xda-developers.com/showthread.php?t=300713 or at http://forum.xda-developers.com/showthread.php?t=268031
i cant start update proces always error 260 or 262
Jasjam Freez on i-mate logo
Dear Friends
my jasjam stop on first screen(i-mate Logo) . I did soft and hard reset again and again but nothing!i remove battery and sim card along the night but nothing again.pls help me what's problem
Thnkas and goodluck
Batman1351 said:
Dear Friends
my jasjam stop on first screen(i-mate Logo) . I did soft and hard reset again and again but nothing!i remove battery and sim card along the night but nothing again.pls help me what's problem
Thnkas and goodluck
Click to expand...
Click to collapse
probably you need reflash again your device with Original Shipped ROM
JasJam Freez on Logo
Dear Rahman
sorry for my bad english.Thank u for ur reply.jasjam freez on the first page!it mean i can not connect it to PC via active sync because it no load to windows!PC can not detect device!so how can i fix this problem without a PC connection ?
Hello,
I did a Hardreset on my XDA Mini and after that it loads when I start the files for the system and after that it changes back to the "Serial v1.02" screen.
How can I fix the phone that I can use it as before?
What is wrong?
I tried to upgrade to the new version of the o2 xda mini and after that it goes back to the "Serial" screen everytime.
I need help :/
I fixed this when I remove battery ant wait two hours. Or just try press soft reset button
Thanks for the answer.
I'll try but I guess that this won't work.
Would be happy if someone could give me more help...
If that don't work, try to reinstall your rom. If that happened when OS was loaded then that could be rom fail
hay hard reset again & plug your charger. try to this way.
reflash your ppc but use Windows XP
flash any shipped rom or coutlla's rom