i was installing new rom on my device.when it was 12%, the computer got locked and i had to reset.Now,my baby did not reflash again.i tried again but himaupragadeutility gave : communication problem. what can i do now? can anyone help me? so a few people know this device, the others even do not know what pda is. what i can do?????????????????????????????
Try putting your device into bootloader mode and making sure your XDA is plugged into the mains as well. There's also an upgrade program which bypasses country id checks.
Good luck.
I got the same problem with my Qtek 2020i today!!!!!
The device is dead and i can't put it into bootloader mode!
I need your help please
Try taking the battery out for about 1 hour. This will run the backup battery down therefore wiping the ram. Put the battery back in, connect it to the mains and put it into bootloader by pressing power, action and reset for about 3-5 seconds until serial appears on screen. No backlight so look carefully.
I tried to remove the battrey for 1 hour but it's still the same!
any way thanks for trying to help pug.
Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...
I have a Prophet (M600) G4 with the last HTC ROM and recently radio upgrade and everything works fine till in installed Resco keyboard and had to soft reset the device. Till then the device comes up normally with the Qtek welcome screen but during the next step to “the windows screen ??” appears a white screen and nothing happened after it. Strange enough hardreset don’t work and its impossible to enter the bootloader. Moving the battery and reset several times has no results. Try to flash it again but impossible because I have no connection to PC. Can someone help me please??
Help! My Dopod D810 dead, can only run bootloader
All ROM I tried are not accepted by bootloader. What can i do?
fuego_nl said:
I have a Prophet (M600) G4 with the last HTC ROM and recently radio upgrade and everything works fine till in installed Resco keyboard and had to soft reset the device. Till then the device comes up normally with the Qtek welcome screen but during the next step to “the windows screen ??” appears a white screen and nothing happened after it. Strange enough hardreset don’t work and its impossible to enter the bootloader. Moving the battery and reset several times has no results. Try to flash it again but impossible because I have no connection to PC. Can someone help me please??
Click to expand...
Click to collapse
qtek s200- prophet problem please help
After reset work but screen is blank with green and blue lines,can some body help
hello. i have an o2 i-mate jasjar phone. i updated my rom and since then my phone wont start up.
i tried going into bootloader mode and re-installing any rom that i could find with that mtty program, even with the original rom, the
the rom installs just fine, but when i do the hard reset the phone goes up to the start up screen showing
the rom info and just stays there.
i also updated the bootloader from v1.00 to v1.01 to see if that fixes anything but no luck.
does anyone have a clue of what is going on?
p.s when i connect the phone with ac power the led that shows if the phone is charging wont light up. dunno why! :S
PLEASE HELP ME!!!
does anyone has a clue of whats going on???
i really need some help here please!!
there are some progs on wiki. Instructions for those stuck on bootscreen.
i am not stuck on boot screen. i am stuck on the screen that shows the ram info, i think its called splash screen....
can somebody help me?
Hi
Plssssss Help me. i'm using HTC touch 3450 and i have upgraded my device with wm6.1
NOW THE PROBLEM IS...
1. MY DEVICE BUTTONS(HARD KEYS) NOT WORKING BUT I CAN MAKE THE DEVICE IN BOOTLOADER (TRICOLOR) MODE BY PRESSING CAMERA + POWER BUTTON.
2. AFTER INSTALLING A ROM WHENEVER MY DEVICE STARTS IT SHOWS THE HARD RESET SCREEN (BLACK SCREEN........... ALL THE DATA ...BLAH BLAB......)
I HAVE TO REMOVE THE BATTERY AND START THE DEVICE AFTER 30 MINS.) PLEASE NEED THE SOLUTION ......
3. I AM TRAYING THIS FOR A MONTH BUT NOTHING HAPPENS
PLZ GUYS HELP MEEEEEEEEEEEE OTHERWISE I'LL BE CRAZY!!!!!
rupesh baviskar said:
Hi
Plssssss Help me. i'm using HTC touch 3450 and i have upgraded my device with wm6.1
NOW THE PROBLEM IS...
1. MY DEVICE BUTTONS(HARD KEYS) NOT WORKING BUT I CAN MAKE THE DEVICE IN BOOTLOADER (TRICOLOR) MODE BY PRESSING CAMERA + POWER BUTTON.
2. AFTER INSTALLING A ROM WHENEVER MY DEVICE STARTS IT SHOWS THE HARD RESET SCREEN (BLACK SCREEN........... ALL THE DATA ...BLAH BLAB......)
I HAVE TO REMOVE THE BATTERY AND START THE DEVICE AFTER 30 MINS.) PLEASE NEED THE SOLUTION ......
3. I AM TRAYING THIS FOR A MONTH BUT NOTHING HAPPENS
PLZ GUYS HELP MEEEEEEEEEEEE OTHERWISE I'LL BE CRAZY!!!!!
Click to expand...
Click to collapse
hi
if u can get ur tricolor screen then try this
connect the usb cable to pc and see if u get the USB words on the phone tricolor screen if so good try flashing any official ROM the same happened to my phone long back did the above got my phone back asuming u have done HSPL for ur phone if u have not done that then the only way is to take it to service
hope it helps good luck
thanks
hari
Wrong forum.. Touch P3450 is not a touch 3g , its the original touch (ELF version)
but i will try and help as i have owned both.
if your hardware buttons are not working it could be possible that your send and end keys are stuck down as this key combo brings up the hard reset you are talking about.
think you are going to have to open it as it sounds like a hardware fault, and if you cannot get into bootloader you cannot flash
if it was working alright before this is not the case, but either way you will have to fix your camera button and get into bootloader