Database Users

SD Card flashing locks at 003C0000...HELP!!!

I was trying to flash my TMO Pocket PC to 4.01 ENG and it locked at PRG 003C0000 and reset back to the bootloader. I thought it was just the card so I went to my backup and got the same thing so I popped my card into my reader/writer and tried to flash using the TMO original 3.14 and same thing again.
Is my XDA dead?
Please help me out.

use a different card

and is your flash card big enough to hold 32M?
a card that says '32M' can usually only hold about 29M or 30M of data. which is not enough for rom flashing.

I have tried 2 different cards, they are both 128MB's

Maybe you should download a new rom and try writing that to a card.

I tried the TMO original from Yorch, a 4.01 cooked rom and the official 4.01

decepticon said:
I tried the TMO original from Yorch, a 4.01 cooked rom and the official 4.01
Click to expand...
Click to collapse
Confirming this is your first ROM upgrade on that unit? If so what boot loader version is it running?
HTH

I have upgraded 3 or 4 times via both Activesynch and SD card flashing with no problems, bootloader 5.15

Anyone?

Help?

your flashrom have problem.
send to T-mobile for service, if it is still in warranty.
or send to me to repair!

Flash Radio Stack with SD CARD

How can im flash MDA with SDCARD wifhout active sync

you don't need active sync to use the SD method ... maybe you better retype your question

i have upgraded my XDA I for wm2003 .... does it upgraded the radio stack as well or i have to do that in seprate way ? if yes then where can i get the radio rom and to upgrade it

Press hold power with soft reset, then if you SD has images, it will confirm you to download to upgrade your XDA I, if empty it will flash your XDA I images to SD..that all.....
Try your best XDA I never expire. but MDA = XDA

sunpower said:
i have upgraded my XDA I for wm2003 .... does it upgraded the radio stack as well or i have to do that in seprate way ? if yes then where can i get the radio rom and to upgrade it
Click to expand...
Click to collapse
Sunpower,
If your GSM part is working fine in your device I recommend from you not to upgrade it. Lots of ppl here has dead devices cos of that upgrade.
Make a search about Failed Rsu upgrade and read what happened to them , believe me you wont touch this part of upgrade.

same ramram
don't try to upgrade RSU if old versions still ok.....because now i already have 2 dead xda in my hand ..... i garantee ramram idea.....

Radio ROM on SD - Anyone?
Hi all
I've got an O2 XDA with broken radio ROM from my friend. I also have my AT&T SX56 running normally (with cooked 4.01.16 ENG OS and 6.12 radio ROM).
I've tried re-flashing the dead O2 XDA radio ROM (by running RSUpgrade.exe inside WM2003 or 2002) without any success. It seems to me that a SD radio ROM flashing is a good way to try. But I can not get my SX56's radio ROM on SD card, since the device keeps asking me to connect a RS232 cable and run PC monitor when I try to create CD + GSM dump on SD card, using boot loader options.
Question:
- Is the any way to create radio ROM upgrade SD card, using XDATools or similar tools, and radio upgrading files (those file that come with RSUpgrade.cab, for example), or
- Could anybody provide me an image of such a SD card, or
- How can I dump GSM ROM form my SX56 to SD card, without RS232 cable and PCMonitor
Current soft/hardware info:
My SX56 is running 5.15 boot loader, cooked 4.01.16 ENG OS and 6.12 radio ROM
The dead O2 XDA is running 5.15 boot loader, cooked 4.01.16 ENG OS (could be changed to any version)
Thank you for reading.
Tuan

Wallaby radio stack upgrade problem solve successfully!!

Hi everybody
Yesterday i had a problem trying to upgrade my wallaby to radiostack 6.18 tu RSU 6.24.
When i was doing the upgrade with the rsu files and the upgrade was in 88% in the screen appears:
" Upgrade problem, please reset" (something like that :? )
When i did the reset i got the boot screen and in the corner only i get the ROM version. The radio stack dissapears and then im not able to have my wallaby works.
Then i get into the wallaby bootloader version 5.15 and i got the following message:
GSM-ERROR
I reset the device a lot of times and nothing. i think " god i lost mi phone"
and then reading posts and posts i solve the problem in this way:
1:- I cook a rom image in an sd card using Xtools and a card reader instaled in your pc.
2.- when you finish insert the sd card with the image, enter again bootloader by holding On/Off and doing a soft reset
3.- Bootloader should tell you something that OS is detected on your SD-Card
4.- Press Action Key to install the ROM
5.-After finishing do a hard reset
Now your ROM should be installed on your device.
6.- turn off your device, maybe you will have to press the power button several times.
7.- Remove your SIM card
8.- Turn on your device, wait about 15 minutes and you can see that the device goes out off that frezze screen and gets into the align screen setup.
9. When you get the TODAY screen connect your device in the cradle and make a new asociation for your device
10. get into the windows file with the explorer of activesync on your pc and copy the 4 radio stack files in the windows file of your deviceq and the .exe file in the \Windows\StartUp folder of your device.
11. Restart the device and the upgrade will begins automaticaly in the back ground
12. when it sucsesfully done, do a soft reset and you must have your radio stack upgrade done and your wallaby completly recovered.
13.- Insert your SIM card again and enjoy
I hope this guide will help you
Rememeber to copy the correct radio stack in your device, i used the RSU 6.24 because i have a PW10B1 wallaby. check your version in the label in the rear part off your device
[/b]
if this tip results succesfully to someone please let me know. thanks

Well done, not many people manage to repair corrupt/missing radio stack, thanks for the details also, it may help resurrect other dead Wallabys.

which RSU to use
hi,
mine is PW10A1 so which RSU to use

Re: which RSU to use
maddawood said:
hi,
mine is PW10A1 so which RSU to use
Click to expand...
Click to collapse
ftp://[email protected]/Wallaby/Radio_Stack/RSU_V4.16_PPC.zip
HTH
Stefan

which rom you used?

Re: which RSU to use
LumpiStefan said:
maddawood said:
hi,
mine is PW10A1 so which RSU to use
Click to expand...
Click to collapse
ftp://[email protected]/Wallaby/Radio_Stack/RSU_V4.16_PPC.zip
HTH
Stefan
Click to expand...
Click to collapse
That link isn't working at the moment - I could sure use it

Link should be:
ftp://xda:[email protected]/Wallaby/Radio_Stack/RSU_V4.16_PPC.zip
Stefan

Thanks Stefan - I saw elsewhere what the password was, and noticed it was missing from the URL. I got the RSU file and have finally managed to get it on to the XDA, but still fails every time it restarts... the old 1% problem... Do you know if it is easier to update the radio stack from an SD card? The XDA is running the special edition ROM, which has at least given me back some control of the device.
Thanks in anticipation
Phil

PhilHirons said:
Thanks Stefan - I saw elsewhere what the password was, and noticed it was missing from the URL. I got the RSU file and have finally managed to get it on to the XDA, but still fails every time it restarts... the old 1% problem... Do you know if it is easier to update the radio stack from an SD card? The XDA is running the special edition ROM, which has at least given me back some control of the device.
Thanks in anticipation
Phil
Click to expand...
Click to collapse
I have the same problem, every time my device restarts, and stop at 1%. So I am wondering if Stefan can help us to give us solution in this case.

Worth the risk?
After reading this ordeal, is it worth the risk to upgrade a working radio stack? Does the telephone work substantially better after the upgrade?

Try other RSU's
kinowong said:
PhilHirons said:
Thanks Stefan - I saw elsewhere what the password was, and noticed it was missing from the URL. I got the RSU file and have finally managed to get it on to the XDA, but still fails every time it restarts... the old 1% problem... Do you know if it is easier to update the radio stack from an SD card? The XDA is running the special edition ROM, which has at least given me back some control of the device.
Thanks in anticipation
Phil
Click to expand...
Click to collapse
I have the same problem, every time my device restarts, and stop at 1%. So I am wondering if Stefan can help us to give us solution in this case.
Click to expand...
Click to collapse
Hi, have you tried using other RSU versions? I had the same problem too (1% fail) using 4.16. After giving up on the 4.16, I tried RSU 4.21 (exe). One shot and I was able to re-flash my RSU. What I did differently was to remove the AC power while doing the RSU upgrade (the exe file prompted me). Hope you get your wallaby up and running again.

I try alot of times but it stop at 1% - full batery got the same result.
help.

Re: Try other RSU's
Thank you for your help. I have tried many vensions of RSU, such as 4.16, 4.21, 6.24, 6.25, etc. But all of them showed 1% mistake.
morph751 said:
kinowong said:
PhilHirons said:
Thanks Stefan - I saw elsewhere what the password was, and noticed it was missing from the URL. I got the RSU file and have finally managed to get it on to the XDA, but still fails every time it restarts... the old 1% problem... Do you know if it is easier to update the radio stack from an SD card? The XDA is running the special edition ROM, which has at least given me back some control of the device.
Thanks in anticipation
Phil
Click to expand...
Click to collapse
I have the same problem, every time my device restarts, and stop at 1%. So I am wondering if Stefan can help us to give us solution in this case.
Click to expand...
Click to collapse
Hi, have you tried using other RSU versions? I had the same problem too (1% fail) using 4.16. After giving up on the 4.16, I tried RSU 4.21 (exe). One shot and I was able to re-flash my RSU. What I did differently was to remove the AC power while doing the RSU upgrade (the exe file prompted me). Hope you get your wallaby up and running again.
Click to expand...
Click to collapse

Re: which RSU to use
LumpiStefan said:
maddawood said:
hi,
mine is PW10A1 so which RSU to use
Click to expand...
Click to collapse
ftp://[email protected]/Wallaby/Radio_Stack/RSU_V4.16_PPC.zip
HTH
Stefan
Click to expand...
Click to collapse
Hi guys i have a pw10a1 too, and my radio version is 4.21, i really think it sucks. so is it a good idea to downgrade to 4.16??? or will it only be made worse. or can i use the 6.25.02 version? or is that for another phone type.. PWIEW srry for all the questions .. if 1 is awnsered. i'm happy

Can't update ROM in my O2 XDA anyways...

Several days earlier, i want to update flash ROM image in my O2 XDA. I want to update my WM2003 (ROM v4.01.16 ENG) to WM2003SE (v3.04.00 ENG - downloaded from xda-developers FTP). But any attempts to do this ended unsuccessful. When i try to update my O2 XDA through SD Flash Card, with the XDAtools, as it is written here: http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_FlashSD , Wallaby boot loader don't boot from SD, and don't displays any messages, look like SD card is not inserted.
When i try to update through USB or serial cable, with ActiveSync, the Programme A display this error message:
============================================
ERROR 011: EXECUTE REMOTE COMMUNICATION PROGRAM ERROR
============================================
Cannot execute the remote communication program.
Please make sure that the USB/Serial cable is properly connected.
============================================
However, Radio stake update (with Programme B) is working, and updating through USB.
What my actions is wrong? Or my device is broken? Please, help me!

As mentioned 1000 times here in the forum:
Update from this ROM Version via EXE-File is not possible You have to downgrade first via SD-Card to another ROM Version (e.g. 3.17.03)
Stefan

LumpiStefan said:
As mentioned 1000 times here in the forum:
Update from this ROM Version via EXE-File is not possible You have to downgrade first via SD-Card to another ROM Version (e.g. 3.17.03)
Stefan
Click to expand...
Click to collapse
Thanks a lot!!!! I try this tomorrow!

Unsuccessful downgrading... Wallaby boot loader don't boot from SD again! What wrong?!

What for SD-Card Writer are you using?
Many internal versions are causing problems.....
You could try enter the bootloader, make a backup of your current ROM. Than reenter your bootloader and check if now the option for downloading the ROM from SD-Card is displayed....
Stefan

LumpiStefan said:
What for SD-Card Writer are you using?
Many internal versions are causing problems.....
You could try enter the bootloader, make a backup of your current ROM. Than reenter your bootloader and check if now the option for downloading the ROM from SD-Card is displayed....
Stefan
Click to expand...
Click to collapse
All right! I understood how to do this. Just reading this forum. I make update ROM through SD card! Forget any cables! SD flashing is cool! Trouble was in bootloader v5.17, with the wallaby_patch_tool, and XDArit, and description for bootloader update, i done this!!! Now i want setup special edition rom!

Cannot Unlock CID on KJam

Hi guys.
I tried unlocking the CID with Lokiwiz0.2b but keep getting the error249 invalid vendor ID problem.
I updated my KJam with the latest iMate ROM thinking it had A2DP, but found it doesn't. I now want to flash the Qtek test WWE ROM which does. BUT after running Lokiwiz and selecting option C and then trying to update the ROM I keep getting the message.
I have tried unbundling Lokiwiz again in case it was a problem there, but no joy.
Any ideas anyone? or has it anything to do with the new ROM that maybe Lokiwiz can't address yet?

sangasanga said:
Hi guys.
I tried unlocking the CID with Lokiwiz0.2b but keep getting the error249 invalid vendor ID problem.
I updated my KJam with the latest iMate ROM thinking it had A2DP, but found it doesn't. I now want to flash the Qtek test WWE ROM which does. BUT after running Lokiwiz and selecting option C and then trying to update the ROM I keep getting the message.
I have tried unbundling Lokiwiz again in case it was a problem there, but no joy.
Any ideas anyone? or has it anything to do with the new ROM that maybe Lokiwiz can't address yet?
Click to expand...
Click to collapse
Your solution is to downgrade to the previous kjam rom, then cid unlock, then flash the Qtek rom.
Just run the K-JAM_WWE_1010903_106_10110_ship.exe upgrader to err downgrade. ;-)

summiter said:
sangasanga said:
Hi guys.
I tried unlocking the CID with Lokiwiz0.2b but keep getting the error249 invalid vendor ID problem.
I updated my KJam with the latest iMate ROM thinking it had A2DP, but found it doesn't. I now want to flash the Qtek test WWE ROM which does. BUT after running Lokiwiz and selecting option C and then trying to update the ROM I keep getting the message.
I have tried unbundling Lokiwiz again in case it was a problem there, but no joy.
Any ideas anyone? or has it anything to do with the new ROM that maybe Lokiwiz can't address yet?
Click to expand...
Click to collapse
Your solution is to downgrade to the previous kjam rom, then cid unlock, then flash the Qtek rom.
Just run the K-JAM_WWE_1010903_106_10110_ship.exe upgrader to err downgrade. ;-)
Click to expand...
Click to collapse
Tried doing that but I can't downgrade. The RUU says says I must get an up to date version. I recall when I loaded the new ROM it said I can't go backwards afterwards.
Does anyone know how can I do that?

don't know if this would work but have you tried bootloader mode?

unable to unlock CID for my Imate Kjam
Can any one help me to unlock CID for my Imate Kjam.
I am unable to install WM6.
Will appreciate the help.

what is your ipl-spl

chg1282002 said:
what is your ipl-spl
Click to expand...
Click to collapse
mine its 2.16.0001 , can anyone help me? iv already search and see many threads about this but with no result for me =\ i think first i have to unlock the CID then update the rom... but still no result =\

johnnybazukatone said:
mine its 2.16.0001 , can anyone help me? iv already search and see many threads about this but with no result for me =\ i think first i have to unlock the CID then update the rom... but still no result =\
Click to expand...
Click to collapse
Hi i see yours is G4.
the way i CID Unlocked my wizard to install WM6.5 is:
I Downloaded SoftSPL ( it Temp removes the lock )
--- http://forum.xda-developers.com/attachment.php?attachmentid=50344&d=1189619527 --
So after you downloaded that unZip it and inside there will be 2 CAB files.
move the CABs to your phone:
Cert_SPCS.cab )install on Phone 1st(
EnableRapi.cab )install on phone 2nd(
:
After you have installed them
Move The Rom you want to install into the SoftSPL Folder And Rename the ROM
nk.nbf
Then make sure the Phone is connected to Pc via Cradle/Cable
Then Just Run START-sSPL.exe (inside SoftSPL folder on pc)
tick and next on the screens that come up and then you mobile screen goes White (Dont Worry) then it will load rom you will have a bar on Desktop that loads to 100% .. just Let it finish then mobile reboots and you should be fully loaded with your copy of WM6
Hope This Helped

johnnybazukatone said:
mine its 2.16.0001 , can anyone help me? iv already search and see many threads about this but with no result for me =\ i think first i have to unlock the CID then update the rom... but still no result =\
Click to expand...
Click to collapse
Hi i see yours is G4.
the way i CID Unlocked my wizard to install WM6.5 is:
I Downloaded SoftSPL ( it Temp removes the lock )
--- http://forum.xda-developers.com/attachment.php?attachmentid=50344&d=1189619527 --
So after you downloaded that unZip it and inside there will be 2 CAB files.
move the CABs to your phone:
Cert_SPCS.cab )install on Phone 1st(
EnableRapi.cab )install on phone 2nd(
:
After you have installed them
Move The Rom you want to install into the SoftSPL Folder And Rename the ROM
nk.nbf
Then make sure the Phone is connected to Pc via Cradle/Cable
Then Just Run START-sSPL.exe (inside SoftSPL folder on pc)
tick and next on the screens that come up and then you mobile screen goes White (Dont Worry) then it will load rom you will have a bar on Desktop that loads to 100% .. just Let it finish then mobile reboots and you should be fully loaded with your copy of WM6
Hope This Helped