Hello everyone, I have just updated the ROM to 400.11 ENG WM2003 from ROMKITCHEN. Now, there are two issues I have:
1- active sync is not able to find the device. I had version 3.5, and thinking that upgrading it to 3.7 would solve it. NO LUCK. Though, USB seems to be working, when I insert some other media devices, there is concection btw the device and the comp.
Any idea how I can recover the connection.
2- the radio signal is very poor, compared to previous. The signal strength shown only one bar whilw it had three before at the same location.
Any help highly appreciated. Please help...
Thanks,
BTW here is the error message I get:
When I go to Act. Sync and click on get connected.
I searches for it, then says your device was not detected.
1 - I had the same problem after upgrading but a hard reset cured that.
2 - The signal bar is misleading as it is actually stronger than what is indicated.
It did work. Thanks a lot reydiodj
Just Reset Your PDA then connect your usb again
(Work with my xda 4.00.05 & ActiveSync 3.7.1)
Related
I just upgraded TMO radio stack to 6.24.00, works flawlessly. Tested the RS with calls, web connections, incoming call while on web ... perfect.
However, ActiveSync will not recognize a partnership with my PDA now. Reverts to Guest every connection.
Reinstalled ActiveSync ... no luck. Soft reset PDA ... no luck. Tried it on a WinXP-HE and Win2K computer, same on both.
Have searched forum & seen a few enteries on this subject but no solutions. Running TMO ROM 4.00.21 & TMO RS6.24.00.
Anybody had this issue & successfully resolved it?
Yeap been there seen that but had forgotten about those problems until I read your post! :wink:
Try downgrading back to 3.7, my sig states what I ended up doing to fix it for me! :wink:
Also you might try turning the device off before you put it in the cradle
so times that helped if I remember correctly.
HTH
Resolved problem by uninstalling ActiveSync 3.7.1, restart Windows, reinstall ActiveSync 3.7.1 and it detects new USB hardware, starts the Partnership wizard and things are okay.
I've tried about one gazillion suggestions to make Activesync work over USB on my Qtek 9100, and I've given up. I went for BT connections, which works fine.
However, RUU doesnt work over a BT connection (i get to the multicolor boot screen, and, of course lose the BT that would allow the update to finish...).
Is there a way to do it via the SD card, and, if so, can somebody get me the SD image for the latest french version ?
Thanks all.
What is the problem with your USB ActiveSync?
I thought I was going to go crazy trying to sort out mine, because it would just hang on "Trying to obtain address" (=DHCP) when I connected.
In short, the problem turned out to be having the DHCP service at "Manual" (go to Start->Control Panel->Administrative Tools->Services). I resolved it by choosing "Automatic" for starting the DHCP service. If it's not set at "Automatic" for the start type,
ActiveSync won't recognize the device because the background method of connection for ActiveSync involves the PDA acting as a DHCP server and your computer receiving an arbitary IP address in order to communicate with the PDA.
Thanks for the suggestion, but its one of the many things I tried... to no avail.
So, back to my original Q, is there a way via the SD card ?
i've read that there is a prog. to specially format the sd card, and include the rom extracted from the .exe... please help me, I can't find the reference.
Use bootloader
If you put your Universal into bootloader mode as documented here: http://forum.xda-developers.com/viewtopic.php?t=37432 then you can connect to your PC over USB without Activesync and run the appropriate upgrade program.
Although I have Activesync working over USB intermittently I found this the surest way to upgrade.
Hope this helps!
excellent !!
Activesync doesnt work, but the RUU does !!
Thank you very much
Hi @all,
I just upgraded to WM6. Now I have 2 Problems:
1. I can't connet to WIFI Hotspot
2. After Softreset and entering the PIN it says "No service" (but not all the time)
3. I am using Voice Command 1.6 but I dont hear the announcements through my Headset
Can anyone help?
Greetings
Peter
1. Depends on hotspot encryption (you can do this trick: turn on wifi trough wlan manager start-settings-connections-wireless lan, it will turn on and turn off by itself, then turn on wireless trough comm manager, it will start but it will not connect to any network, so turn it off from comm manager and turn it on again and if the encryption is supported it will connect)
2. This never happened to me, try to clean your sim card contacts
3. I had this problem with WM5 also but i not remember the solution, try to search the forums for one
Hi xplode,
1. Solved. At home it works, but at work not. I'll try to find out the problem
2. It's only after a sofreset. When I go from the phone-application into Menu-Options-Network and klick the button "Find Network" then it finds my GSM-Network and everything is Ok
3. Problem not yet solved. Can't find any usable threads.
By the way. It doesn't show at the top of the screen that my headset is connected. I only see it in the phone-application. Any solution for this?
Thanks
Peter
linuxpete said:
Hi xplode,
1. Solved. At home it works, but at work not. I'll try to find out the problem
2. It's only after a sofreset. When I go from the phone-application into Menu-Options-Network and klick the button "Find Network" then it finds my GSM-Network and everything is Ok
3. Problem not yet solved. Can't find any usable threads.
By the way. It doesn't show at the top of the screen that my headset is connected. I only see it in the phone-application. Any solution for this?
Thanks
Peter
Click to expand...
Click to collapse
did you upgrade the radio firmware? I had some issue's with the radio after wm6, I upgraded to 1.15 and all the problems where fixed...
Hi Datake,
It's the original ROM from Helmi. Where do I find the Radio-Update? How do I install it?
Thanks
Peter
NO services gsm, after soft reset
I don´t have apply rom radio update in my qtek 9090 (blue angel)...
My radio rom version is 1.06...
If I apply a soft reset, I lost my signal gsm...
After 2 tries (2 soft reset), the signal come back...
I have a problem when I try apply rom radio upgrade to 1.15.
(connection failed, after activesync is closed in my pc).
(PS: using upgrade_noID)
How can I proceed in this case ?
Help me guys... please...
Rodrigo
Qtek 9090 (blue angel) - WM6 R0 - radio rom 1.06
MS Activesync 4.5
Brazil.
Hi Peeps,
I have been lurking and learning here for a while now, but I cannot find the solution to this problem,
I hav e an Orange SPV M3100, using the HardSPL boot loader (2.10.oli), the latest rom from orange (oct 07) and radio version 1.38
the problem is that when i sync with active sync (4.5 build 5096) it syncs ok and then about 1 min after sync it loses connection.... so if im copying files or about to copy i cant, I then need to reset the phone and restart AS to get it to connect again???
any ideas as to what is going on? im tempting with upgrading the rom/radio but i dont want to try it if it is going to disconnect half way through!
Cheers
Dazzler
dazzler22 said:
Hi Peeps,
I have been lurking and learning here for a while now, but I cannot find the solution to this problem,
I hav e an Orange SPV M3100, using the HardSPL boot loader (2.10.oli), the latest rom from orange (oct 07) and radio version 1.38
the problem is that when i sync with active sync (4.5 build 5096) it syncs ok and then about 1 min after sync it loses connection.... so if im copying files or about to copy i cant, I then need to reset the phone and restart AS to get it to connect again???
any ideas as to what is going on? im tempting with upgrading the rom/radio but i dont want to try it if it is going to disconnect half way through!
Cheers
Dazzler
Click to expand...
Click to collapse
I have this problem often as well, I suggest that you do the following. Go to the Devices MMC and uninstall "Windows Mobile Device" from the network adapters topic. Then remove and reconnect your device. I also removed the activesync program and reinstalled it from the web. Fixed the problem for a long time.
One other thing you can do is to go to the USB to PC applet in the connections settings page and disable the "Advanced Network Functionality" option. that should make connection more stable.
Can't say I know what's going on but those two things seem to help.
Hi,
Two months ago I've upgraded the ROM of my Polaris. At beginning I've got some problem in use ActiveSync (windows XP) or Mobile Center (Vista), after two or three try it worked. But now there is no way to connect the Polaris with any computer (I've tried 4 different computer with different version of Windows). I always get the message that the USB device is not recognized. Even Bluetooth does not work. I've tried all methods and hard reset the device several times, install and uninstall ActiveSync/Mobile Center no way to get connected. The situation become worst because the phone stopped working. So, please, could someone help me in trying to connect the Polaris with the PC?
The ROM that is installed is:
R 1.58.21.23
G 25.65.30.04H
D 1.52 PQ015
Thanks,
Adenilson
Adenilson said:
Hi,
Two months ago I've upgraded the ROM of my Polaris. At beginning I've got some problem in use ActiveSync (windows XP) or Mobile Center (Vista), after two or three try it worked. But now there is no way to connect the Polaris with any computer (I've tried 4 different computer with different version of Windows). I always get the message that the USB device is not recognized. Even Bluetooth does not work. I've tried all methods and hard reset the device several times, install and uninstall ActiveSync/Mobile Center no way to get connected. The situation become worst because the phone stopped working. So, please, could someone help me in trying to connect the Polaris with the PC?
The ROM that is installed is:
R 1.58.21.23
G 25.65.30.04H
D 1.52 PQ015
Thanks,
Adenilson
Click to expand...
Click to collapse
Repair you Polaris. Its hardware error with connection jack.
Ok,
I was wondering that could be a hardware problem, but expected that could solve the problem by using another ROM version. In fact, I've a big problem... Polaris is not sold in my country and I has no technical support for it . I brought it abroad. Anyway, thanks for your reply
Adenilson