Database Users

[Q] [Help] i9505 not booting after flashing Omega ROM

I dunno what went wrong here...
1) I have GT-I9505 (SSN: -I9505GSMH). I installed Galaxy S4 toolkit
2) Reboot into download mode. Used toolkit/Odin to root phone. Boots up. See SU.
3) Reboot into download mode. Used toolkit/Odin. Flashed TWRP Recovery
4) Phone boots up normal. Reboot into TWRP recovery. Did a factory Reset. Format.
5) Installed Zip (Latest Omega 9.0 ROM), unchecked the things I didn't want to install. Completed install, no errors reported. Rebooted.
6) Phone stuck on Samsung boot screen. I left it overnight thinking sometimes it may take 15 mins to boot system after new install.
7) Woke up, battery dead. Tried to charge phone. No charging indicators when plugged in. With whatever juice I had left I booted into TWRP recovery, it starts to charge again as I see the % batter increase after 5 mins.
-=-=-=-=- Did the Following to try to repair
a) Reinstalled Omega, this time leaving alll options on. Rebooted, stuck in Samsung boot
b) Flashed Phil CWM touch recovery, did complete wipe to install new ROM. Rebooted into Phil recovery. Flashed OMEGA. Reboot, stuck in Samsung boot.
c) Rebooted into Phil recovery, installed echo ROM, rebooted. Black screen. Rebooted into Phil. This time cannot get into recovery.
d) Started panicking, used Odin flashed TWRP. Would not flash. Something displayed about PIT error. Flashed Phil again. Reboot into recovery, WORKS! (recovery only). Went back into Download mode flashed TWRP. Rebooted, also WORKS!. Did a factory wipe. During wipe there was an error. Format, factory reset, error during wipe. Flashed OMEGA. Reboot. Stuck on samsung boot loop.
e) Downloaded official Samsung kernal for i9505 thinking it was the full flash rom. Flashed with ODIN (hoping to put everything back to factory). Completed flash, phone boots. I get OMEGA ANIMATION!!! Waited for 15 mins. Stuck on Animation. Reflashed TWRP. Rebooted, installed OMEGA...again. Stuck on samsung boot screen.
-=-=-= Kinda frustrated. What did I do wrong in the beginning?
There are so many official roms for the S4 based on region. What can I do to put it back to factory again? I purchased phone in Australia @ Samsung store. I figured download the Australia ROM but there are like 5 of them 4 being network branded roms I think. THe other one XSA is unbranded?
I tried searching for help but so far nothing works.

omega ROM or any other custom ROM uses single CSC so before booting into system you must boot into stock recovery to apply CSC of that ROM, download stock recovery of that firmware the ROM was built from
after applying CSC it will work if not flash Omega 9.0 again , it will work :good::good:

arnob_xperia said:
omega ROM or any other custom ROM uses single CSC so before booting into system you must boot into stock recovery to apply CSC of that ROM, download stock recovery of that firmware the ROM was built from
after applying CSC it will work if not flash Omega 9.0 again , it will work :good::good:
Click to expand...
Click to collapse
Thanks for responding
So I take it when I did the full factory wipe and FORMAT the formatting part erased the CSC?
The steps are:
1) Find stock recovery of the original ROM OMEGA was built on. Use odin, flash that specific recovery. ( I might as well do a complete flash of the original stock firmware)
2) Use odin, replace recovery with TWRP, flash Omega this time no formatting
Reboot should be ok?

kabloomz said:
Thanks for responding
So I take it when I did the full factory wipe and FORMAT the formatting part erased the CSC?
The steps are:
1) Find stock recovery of the original ROM OMEGA was built on. Use odin, flash that specific recovery. ( I might as well do a complete flash of the original stock firmware)
2) Use odin, replace recovery with TWRP, flash Omega this time no formatting
Reboot should be ok?
Click to expand...
Click to collapse
first use CWM or TWRP or whatever you want and format everthing
flash a fresh firmware(latest i prefer)
then flash stock recovery via odin of the built version what v9 was used, simply reboot to recovery and it will say MULTI CSC APPLIED from fresh frimware you used
then flash TWRP/CWM and flash v9
again simply reboot to recovery and it will say MULTI CSC APPLIED from V9
it will reboot, you must need to apply CSC to boot your phone

I can confirm this!
I was trying to flash Omega 9 on top of jamal's 4.3 and my phone always booted to recovery. So I restored my stock touchwiz (no custom recovery or even root) nandroid backup and applied Omega 9: it worked!

douglascamata said:
I was trying to flash Omega 9 on top of jamal's 4.3 and my phone always booted to recovery. So I restored my stock touchwiz (no custom recovery or even root) nandroid backup and applied Omega 9: it worked!
Click to expand...
Click to collapse
thats right stock recovery boot is needed to apply CSC

problem
I need help. I am on stock build i9505XXUBMG5. then I rooted it using CF-autoroot. and i used the 1.85 version of ODIN. (Does the version of ODIN affect how the phone is rooted?) Anyways, After that, it is rooted. then after some time, my Wifi is not working or not turning on. I checked google and found the *#0011# method and turned off the Wifi power saving. Then, at first, it worked. After a while, the problem insists. but randomly turns on. I observed that in the *#0011# -> wifi window, the state is power off. but when it is completely not turning on, the state is now disconnected. How can I fix this?
I tried flashing Omega ROM, because there was a wifi fix on that ROM. But when I finished flashing it and continue to reboot, it's stuck on the boot animation. It is not even the Omega robot animation, just the original animation. (Another problem) i tried wiping cache, delvik cache and data but nothing happens.

macoy_412 said:
I need help. I am on stock build i9505XXUBMG5. then I rooted it using CF-autoroot. and i used the 1.85 version of ODIN. (Does the version of ODIN affect how the phone is rooted?) Anyways, After that, it is rooted. then after some time, my Wifi is not working or not turning on. I checked google and found the *#0011# method and turned off the Wifi power saving. Then, at first, it worked. After a while, the problem insists. but randomly turns on. I observed that in the *#0011# -> wifi window, the state is power off. but when it is completely not turning on, the state is now disconnected. How can I fix this?
I tried flashing Omega ROM, because there was a wifi fix on that ROM. But when I finished flashing it and continue to reboot, it's stuck on the boot animation. It is not even the Omega robot animation, just the original animation. (Another problem) i tried wiping cache, delvik cache and data but nothing happens.
Click to expand...
Click to collapse
Do you have an IMEI showing on your phone? What recovery did you use to flash Omega?
It matters, because some recoveries will screw it up.

Do you try to install with Philz recovery?
Sent from my GT-I9505 using xda premium

macoy_412 said:
I need help. I am on stock build i9505XXUBMG5. then I rooted it using CF-autoroot. and i used the 1.85 version of ODIN. (Does the version of ODIN affect how the phone is rooted?) Anyways, After that, it is rooted. then after some time, my Wifi is not working or not turning on. I checked google and found the *#0011# method and turned off the Wifi power saving. Then, at first, it worked. After a while, the problem insists. but randomly turns on. I observed that in the *#0011# -> wifi window, the state is power off. but when it is completely not turning on, the state is now disconnected. How can I fix this?
I tried flashing Omega ROM, because there was a wifi fix on that ROM. But when I finished flashing it and continue to reboot, it's stuck on the boot animation. It is not even the Omega robot animation, just the original animation. (Another problem) i tried wiping cache, delvik cache and data but nothing happens.
Click to expand...
Click to collapse
At this point I think it is the CSC issue arnob-xperia mentioned.
This is how I corrected my issue.
1) Omega v10 uses newer base FW. In their description it tells u. (ex: ver 9 uses XUBMG5). Search on the i9505 forums here. I can't link for some reason I can't see any of the stickied threads, especially the one listing all avail stock firmwares.
Flash into Philz or TWRP do a complete wipe of everything including data. etc.
You MUST download the full firmware, Not just the smaller kernel and recovery or csc. The full stock fw is usually over 1.6 GB. Anything around that range and u got the right one for Odin flash with the md5. Use Odin to flash. I used 1.85 and it was fine.
2) Once done it will reboot and in theory you are stock everything. At this point, for me somehow the phone got stuck in fricken boot loop. I pulled out battery, reboot into stock recovery and made sure I saw the multicsc. Rebooted. Still boot loop.
After hours of doing all sorts of things and putting the phone aside for a day. Came back, flashed the stock fw again using Odin. Reboot into recovery. Check the multi csc. Reboot. Stuck in boot loop. Reboot to download mode. Then I decided to ROOT the phone for ****s and giggles. This worked!
Phone booted.
3) Now you have stock (for that specific OMEGA fw) w/ the matching CSC. From here on follow OMEGA flash instructions for the specific things it tells u to wipe. DO NOT DO A FULL WIPE/FORMAT like I did (what got me in the mess to begin with).
** For Galaxy S3s, S4s, for some reason I've always had problems with TWRP. I had better luck using Philz. Everyone's personal experience varies on this one.
** I think the problem has to do with the CSC which handles specific region phone and carrier modes. This doesn't mean that it won't work if you use a diff region CSC. Just that it has to match the FW base you are using otherwise you have all sorts of problems. After that you can go in android and setup your APNs etc if you have probs with data. I didn't have this problem and was testing using the UK fw base on AU network sim.
*** Why does Samsung make things so damn complicated. I remember way back in 2k3 using fricken ODIN (samsung flashing utitility) to flash **** and it was the same setup as now. This whole crap about CSC pairing is a bit annoying. It is bad enough there are 6+ variations of S4s lol...
Hope this helps.

wifi problem
kabloomz said:
At this point I think it is the CSC issue arnob-xperia mentioned.
This is how I corrected my issue.
1) Omega v10 uses newer base FW. In their description it tells u. (ex: ver 9 uses XUBMG5). Search on the i9505 forums here. I can't link for some reason I can't see any of the stickied threads, especially the one listing all avail stock firmwares.
Flash into Philz or TWRP do a complete wipe of everything including data. etc.
You MUST download the full firmware, Not just the smaller kernel and recovery or csc. The full stock fw is usually over 1.6 GB. Anything around that range and u got the right one for Odin flash with the md5. Use Odin to flash. I used 1.85 and it was fine.
2) Once done it will reboot and in theory you are stock everything. At this point, for me somehow the phone got stuck in fricken boot loop. I pulled out battery, reboot into stock recovery and made sure I saw the multicsc. Rebooted. Still boot loop.
After hours of doing all sorts of things and putting the phone aside for a day. Came back, flashed the stock fw again using Odin. Reboot into recovery. Check the multi csc. Reboot. Stuck in boot loop. Reboot to download mode. Then I decided to ROOT the phone for ****s and giggles. This worked!
Phone booted.
3) Now you have stock (for that specific OMEGA fw) w/ the matching CSC. From here on follow OMEGA flash instructions for the specific things it tells u to wipe. DO NOT DO A FULL WIPE/FORMAT like I did (what got me in the mess to begin with).
** For Galaxy S3s, S4s, for some reason I've always had problems with TWRP. I had better luck using Philz. Everyone's personal experience varies on this one.
** I think the problem has to do with the CSC which handles specific region phone and carrier modes. This doesn't mean that it won't work if you use a diff region CSC. Just that it has to match the FW base you are using otherwise you have all sorts of problems. After that you can go in android and setup your APNs etc if you have probs with data. I didn't have this problem and was testing using the UK fw base on AU network sim.
*** Why does Samsung make things so damn complicated. I remember way back in 2k3 using fricken ODIN (samsung flashing utitility) to flash **** and it was the same setup as now. This whole crap about CSC pairing is a bit annoying. It is bad enough there are 6+ variations of S4s lol...
Hope this helps.
Click to expand...
Click to collapse
I did flash the Omega v9.1 and applied the wifi fix but the wifi is still broken. I tried unrooting it by flashing the original rom and formatting the data but the wifi is still broken. I can't turn it on. Thanks for the instructions anyways. ))

no pit partition
also, when i tried to root it again, it fails and says there is no PIT partition..

Where is the csc in TWRP so I can so what ones on the phone..??
What stock firmware can I use for a Orange Network in the UK.

GT-i9505 stuck on boot when upgraded from omega v16 to v21
Hello guys,
Well, I followed all the instructions and flashed new bootloader and new modem and after that I installed omega v21 with Full swipe. After that I ended up stuck in boot animation. :s What to do? I already tried to re-flash modem and bootloader, updated CWM and tried to re-install that v21 and after that I flashed twrp over cwm and tried to re-install v21 but always I ended up stuck in that boot animation. :S All installs were successful, but it just wont boot.
What to do?
Hopefully you understand my problem.
Cheers from Finland!
Nico
EDIT:
Ok, I flashed omega rom v19 with full wipe and tried to boot. Didnt work, but then I installed Kies to my computer, opened Kies, Plugged USB in and started my phone and then Kaboom! It booted. What exactly happened there?

BizK1d said:
Hello guys,
Well, I followed all the instructions and flashed new bootloader and new modem and after that I installed omega v21 with Full swipe. After that I ended up stuck in boot animation. :s What to do? I already tried to re-flash modem and bootloader, updated CWM and tried to re-install that v21 and after that I flashed twrp over cwm and tried to re-install v21 but always I ended up stuck in that boot animation. :S All installs were successful, but it just wont boot.
What to do?
Hopefully you understand my problem.
Cheers from Finland!
Nico
EDIT:
Ok, I flashed omega rom v19 with full wipe and tried to boot. Didnt work, but then I installed Kies to my computer, opened Kies, Plugged USB in and started my phone and then Kaboom! It booted. What exactly happened there?
Click to expand...
Click to collapse
Hi, I am having the same problem. First I installed the new firmware (NA5) and modem, tested it with the Omega ROM v21 and boot caught on so now tested the rom Fox Hound 4.1 and am having the same problem.
Kies tested this option but have not had the same luck as you. = /
Anyone know the reason? The rom Google Edition Jamal runs on my phone.
i9505

Modem error when installing any lollipop ROM

Hi,
My Sprint Note 3phone is currently using a Kitkat ROM and TWR recovery. I tried some Lollipop ROMS. After flash the ROM, the phone boot to the page of Android setting, then the UI crashed and the phone reboot, showing Modem error.
Anyone has similar experience or have any idea why this happen? Thanks a lot.

First try wiping all data , cache, dalvik cache and others.
Then install fresh lollipop stock rom from sammobile.com of your phone model and then try to flash it via ODIN rather than through TWRP.
There are many guides on flashing lollipop roms, just read them you'll get it.?✌

TWRP can't install any ROM

After seeing DarkLord's ROM for turning my Note 3 into a Note 7, I decided to give it a go.
I rooted my Note 3 [SM-N9005] with TWRP and went ahead with the install.
Unfortunately, a few seonds after it looks like it's installing, the phone restarts only to display the default Samsung Galaxy Note 3 wording in white with the black ground. It does nothing more.
I have tried other ROMs which result in the same and stock ROMS that display "Could not find 'META-INF/com/google/android/update-binary' in the zip file" instead.
My phone seems to be now totally screwed where I've got no idea what to do next so any help would be very much appreciated.

There is no need to root the phone before installing twrp as twrp can be flashed using Odin.
To flash the rom, did you wipe system, data, and cache before installing?
To start over, flash a stock rom using Odin, then reinstall twrp, perform and full wipe, and flash the custom rom.

audit13 said:
There is no need to root the phone before installing twrp as twrp can be flashed using Odin.
To flash the rom, did you wipe system, data, and cache before installing?
To start over, flash a stock rom using Odin, then reinstall twrp, perform and full wipe, and flash the custom rom.
Click to expand...
Click to collapse
I did wipe the above each time I try to install a ROM but it won't install any whatsoever, as described in my previous post.
Also Odin doesn't seem to see the phone anymore, although I'm not sure if I have to change a setting in TWRP for that to happen.
Maybe if I could install a new recovery manager then I might have a chance but can't get Odin to see my phone.
I'm really worried now, just can't understand what's going on.
Thanks again.

Odin can only recognize the phone if the phone is in download mode, not TWRP/recovery.

Bootloop when trying to flash stock rom

Hi guys,
I'm getting bootloop when I try to flash Stock Rom, I tried 2 roms for my country from samfirmware, tried robot rom from here (im n910c), tried miui v8 beta version also, cant flash 4file repair firmware since there are only available for 4.4 / 5.0, and I'm at 6.0.1
also repartition didnt help
all of these roms get me bootlooped, I can only flash CM rom and its fully functional
what to do?

After flashing your official stock rom via odin, go to Recovery and wipe cache and data/factory reset.

GrippingSphere said:
After flashing your official stock rom via odin, go to Recovery and wipe cache and data/factory reset.
Click to expand...
Click to collapse
I was always doing that, no success

I still need help guys

cannot go back to stock firmware?

hi, Im actually on crdroid and I need to go back to stock samsung firmware
I downloaded G900FXXS1CPK1_G900FITV1CPJ1_G900FXXU1CPJ1_HOME.tar and I tried to flash using odin
stuck at SAMSUNG logo after rebooting (for a split of a second I can see a dead android with NO COMMAND written before SAMSUNG logo)
go back to recovery /(which is not TWRP anymore) and wiped data and cache. nothing has changed
I now have installed crdroid again but I need to go back to official samsung, somebody can help?

where did you get the tar file from? did it say completed in Odin?

from updato.com and odin sais PASS with green color
EDIT is there, maybe, a custom rom from original samung firmware?

wiping data and cache from recovery not enough, do a factory reset then if still a no go redo odin fw flash

vincom said:
wiping data and cache from recovery not enough, do a factory reset then if still a no go redo odin fw flash
Click to expand...
Click to collapse
a factory reset is just wiping system, cache and dalvik in essence. I always do a factory reset, wipe cacke, dalvik and system 3x each and delete the android folders if im just flashing a new ROM. Plus, hes doing an Odin flash, so wiping shouldnt be necessary, but deleting the android folders should still be needed
---------- Post added at 12:22 PM ---------- Previous post was at 12:22 PM ----------
zazolo said:
from updato.com and odin sais PASS with green color
EDIT is there, maybe, a custom rom from original samung firmware?
Click to expand...
Click to collapse
get it from sammobile.com/firmwares. Thats the only real place to get them. everywhere else can have untrusted files

odin does not wipe/reset
in stock recovery iirc theres no wiping data, so reset needs to be done, its solved many fw updates/downgrades issues via either ota or odin.
i usually wipe everything(Dalvik, System, Data, Cache) via twrp b4 flashing w/odin

while I'm downloading from sammobile (sloooooooooow), I'm tring to flash fw again
I'm still getting SAMSUNG logo problem...
tried wiping again cache... nothing
flashed TWRP and did wipe factory reset... again, same issue.
I did a full wipe before flash

zazolo said:
while I'm downloading from sammobile (sloooooooooow), I'm tring to flash fw again
I'm still getting SAMSUNG logo problem...
tried wiping again cache... nothing
flashed TWRP and did wipe factory reset... again, same issue.
I did a full wipe before flash
Click to expand...
Click to collapse
the sammobile d/l does take FOREVAAAAR!!! but wait for that to complete and try it. im betting that your other tar.md5 was corrupt

15 minutes to go....

steps I did:
1: via TWRP wiped EVERYTHING
2: connected to PC in download mode and flashed the firmware via ODIN 3.12
3: booted in recovery and wiped data/factory reset and cache partition
4: reboot and...... seems to work fine (feared for a moment, took almost 20 minutes to start apps optimization)

zazolo said:
steps I did:
1: via TWRP wiped EVERYTHING
2: connected to PC in download mode and flashed the firmware via ODIN 3.12
3: booted in recovery and wiped data/factory reset and cache partition
4: reboot and...... still stuck at SAMSUNG LOGO
Click to expand...
Click to collapse
how long did u wait at logo
try this version of odin, i never had a fail w/it on my s5, in odin only use the "AP" button and leave settings as they are.
ODINv3.10

corrected my original post, after 20 minutes of waiting, started apps optimization, thanks to everybody

zazolo said:
steps I did:
1: via TWRP wiped EVERYTHING
2: connected to PC in download mode and flashed the firmware via ODIN 3.12
3: booted in recovery and wiped data/factory reset and cache partition
4: reboot and...... seems to work fine (feared for a moment, took almost 20 minutes to start apps optimization)
Click to expand...
Click to collapse
cool. told ya we could get ya up and running
also, the initial boot after the Odin flash can take forever too

Can somebody please help me. I flashed a new firmware with odin. It flashed sucssesfully but it keeps restarts on samsung logo so it doesn't boot on. Please guys help me to fix this problem ???

mrllokman said:
Can somebody please help me. I flashed a new firmware with odin. It flashed sucssesfully but it keeps restarts on samsung logo so it doesn't boot on. Please guys help me to fix this problem ???
Click to expand...
Click to collapse
whats the model of your phone, what odin version did you use, what firmware did you flash and where did you get it from?

youdoofus said:
whats the model of your phone, what odin version did you use, what firmware did you flash and where did you get it from?
Click to expand...
Click to collapse
I have Sm G900H, my odin version is 3.11.1 I flashed the firmware from sammobile. It boots up only if i install cyanogenmod.
I think I have problem with kernel. I don't know please help

mrllokman said:
I have Sm G900H, my odin version is 3.11.1 I flashed the firmware from sammobile. It boots up only if i install cyanogenmod.
I think I have problem with kernel. I don't know please help
Click to expand...
Click to collapse
what version of android is the cyanogenmod you had installed and what version are you flashing in Odin?

youdoofus said:
what version of android is the cyanogenmod you had installed and what version are you flashing in Odin?
Click to expand...
Click to collapse
cm13 and i wante to go back to stock G900HXXU1CPL4_G900HOXY1CPL4_G900HXXU1CPCA_HOME.tar

mrllokman said:
cm13 and i wante to go back to stock G900HXXU1CPL4_G900HOXY1CPL4_G900HXXU1CPCA_HOME.tar
Click to expand...
Click to collapse
try a fresh download of the tar.md5 and flash it in the odin posted above 3.10