Related
The help, please! Constantly continued bootloop
There is an insertion, the programmed equipment for FlashTool or Odin
Huawei G7_L01?
I can not come in Fastboot
download ur offcial rom and put in dload folder on ur sdcard. power off ur device and hold power + vol up + vol down and wait until the instalation finish and supposedly it will restored back ur bootloader
Ascend G7-L01 doesn't boot
Hi,
I have the same problem after upgrading my G7-L01 by putting dload in SDcard.
The MUI update started and finished 100% but the phone become bricked!
It is detected as "RELINK HS-USB QDLoader 9008 (Port16)".
I think that I must flash now with SP Flash Tool or other tool! But I didn't find a ROM for that (with scatter).
Thanks for help!
hosnix said:
Hi,
I have the same problem after upgrading my G7-L01 by putting dload in SDcard.
The MUI update started and finished 100% but the phone become bricked!
It is detected as "RELINK HS-USB QDLoader 9008 (Port16)".
I think that I must flash now with SP Flash Tool or other tool! But I didn't find a ROM for that (with scatter).
Thanks for help!
Click to expand...
Click to collapse
i have the same scenario. my phone still bricked. did find any solution to make it boot again ?
Hi All,
I need help to bring back my Asus Zenfone 2 Laser ze550kl from dead condition, I can't enter fastboot mode to flash any ROM also. Device manager only shows "Qualcomm HS-USB QDLoader 9008 (COM3)" under Ports section. After searching online, I found a link to recover it, but it needs certain files which I could not find in web. The files required are:
rawprogram0.xml
patch0.xml
for ze550kl. I have installed QPST 2.7 Qualcomm tool, and additinally need the complete EMMC image.
https://devlakiutak.wordpress.com/2013/08/10/fixdeadboot/
Can someone please help ?
Thanks
gurung_vishwas1 said:
Hi All,
I need help to bring back my Asus Zenfone 2 Laser ze550kl from dead condition, I can't enter fastboot mode to flash any ROM also. Device manager only shows "Qualcomm HS-USB QDLoader 9008 (COM3)" under Ports section. After searching online, I found a link to recover it, but it needs certain files which I could not find in web. The files required are:
rawprogram0.xml
patch0.xml
for ze550kl. I have installed QPST 2.7 Qualcomm tool, and additinally need the complete EMMC image.
https://devlakiutak.wordpress.com/2013/08/10/fixdeadboot/
Can someone please help ?
Thanks
Click to expand...
Click to collapse
if your mobile is turning then surely u can enter the fastboot mode, bsc i hav faced it too
Here you have another tutorial: http://www.droidsavvy.com/unbrick-qualcomm-mobiles/
Someone said it the comments that you will find rawprogram0.xml patch0.xml and file after you extract them from the ROM.
Here is the stock marshmallow ROM: https://www.asus.com/support/Download/39/1/0/22/ZROQURlyupei1ZQz/32/
The same happens to me, trying to unlock the bootloader phone. I've sended my phone to warranty and they opened the phone to fix
Sorry for bad english
Good luck
gurung_vishwas1 said:
Hi All,
I need help to bring back my Asus Zenfone 2 Laser ze550kl from dead condition, I can't enter fastboot mode to flash any ROM also. Device manager only shows "Qualcomm HS-USB QDLoader 9008 (COM3)" under Ports section. After searching online, I found a link to recover it, but it needs certain files which I could not find in web. The files required are:
rawprogram0.xml
patch0.xml
for ze550kl. I have installed QPST 2.7 Qualcomm tool, and additinally need the complete EMMC image.
https://devlakiutak.wordpress.com/2013/08/10/fixdeadboot/
Can someone please help ?
Thanks
Click to expand...
Click to collapse
colonho said:
The same happens to me, trying to unlock the bootloader phone. I've sended my phone to warranty and they opened the phone to fix
Sorry for bad english
Good luck
Click to expand...
Click to collapse
Thanks for reply. I think that is the last option which I have now. I was trying to correct it myself, but can't unless I have at least FASTBOOT working.
Fastboot erase config....
After that I stucked at boot logo
Used xfstk then aft but stucked at boot used fastboot commands for flashing system all gonna smooth but stucked at boot...
Used recovery to sideload marshmallow ... succeed. But also stucked at boot ..unlock boot loader flash TWRP flashing custom rom also stucked at boot logo... PLZZ help me guyzzz
And it shows error in TWRP
Unable:to mount Config(invalid argument)
Hi~ guys, I am an android phone user from China who bought LG G4 Japanese Edition [LG isai vivid V32] last month.
After delete "google play service" in system, then reboot, but the device shows [Security Error Authentication Fail #9]
and automatic started again and again, Ops~ device bricked, GG! :crying:
As we know the resources and softwares are not friendly to LG isai vivid V32, the Firmware is also rare, cos I can't find any tip for LG V32 in XDA,
So it is more difficult for us to save the bricked device.
Due to the [Recovery Mode] still can't solve this problem, here we need to use TOT Firmware to go back to stock,
KDZ is also available to reflash, cos I didn't get the KDZ Files, so I choose TOT to reflash my device.
If your LG V32 device have bootloop or stuck on LG Logo, this method would also help you out.
Now Let me tell you the TOT Method to unbrick your LG isai vivid V32.
Before reflash firmware, you need to download the things below:
1)Download the driver
--[LGUnitedMobileDriver_S52MAN314AP22_ML_WHQL_Ver_3.14.1.exe]
2)Download Both TOT File & DLL File:
--LGV32HL-04-V10o-440-51-OCT-13-2015+0.tot
--LGFLASH_LG_G4_CODEFIRE.dll
3)Download flashtool
--[Setup_LGFlashTool_1.8.1.1023.exe]
4)Download Megalock
--[Megalock.dll]
( I am a new user, due to the policy of XDA forums, so I can not posting outside links,
the softwares which are metioned above, you could google it then download)
Install:
1. Install LGUnitedMobileDriver
2. Install LGFlashtool to C:\
3. Don’t run Flashtool at first, cos you will find that is locked
4. Copy [MegaLock.dll] file to C:\LG\LGFlashtool,
Replace the old MegaLock.dll file to unlock.
5. Extract the TOT file from the Zip,ready for using.
6. Ensure the softwares would work, restart your Windows.
1. Download Mode/Firmware Update
1)power off device
2)press and hold [Vol+] then plug USB cable on connect to pc
3)device shows [Download Mode]
2. Change COM port to 41
1)go to Windows [Device Manager]
2)double click [LGE Mobile USB Serial Port] and tap to [Advanced]
3)change the COM Port to COM 41 then click ok.
4)unplug USB cable but keep device in Download Mode.
3. Import the Firmware
1)Run LG Flashtool
2)in the tool you can see [Model Config]
3)select [Manual Mode],select .dll in files, select TOT Firmware
4)click [Brush Button] change the [LIMO port] to 101
5)on the right side, you could select 1~16 to narrow down the range of searching ports
6)click [ok]
4. Reflash Firmware
1)click the [Yellow Arrow Button]
2)after CRC, tool will show [READY!]
3)plug USB cable to device then the TOT install would be trigged.
4)when process go to about 80%.screens will light up
5)after upload Minios, screen shows in Blue color
6)when flashtool shows [PASS!],it means Success.
Meanwhile screen shows [Factory Reset Statu 3].
5. Reboot
1)unplug USB cable
2)pull battery and reload
3)press power button to Star your device.
PS: If process Failed, I suggest you to unplug USB cable and battery and do this method again.
At last, Here I would like to thank lgviet forum in Vietnam and hyelton who Recognized Contributor on 13th May 2015, 07:07 PM
Some Tips for LG G4 Japan aka isai vivid V32
1. ROOT
After reflash TOT firmware,the system is rooted.
so you don't need other app to root it.
If you can't get the access of root, [360 super root] and [KingRoot] would help you.
By the way,a part user of V32 say, they got bootloop after use Kingroot.
and if you load 360super root, then you can't use [Super SU#]
2. Recovery Mode
The correct way to into [Recovery Mode] is:
1) Power off device
2) Press and Hold [Vol - ] and [Power button]
3) When screen shows logo, keep press [Vol - ], release [power button] for one second, then press and hold [Power button]
4)then screen would shows [Factory data reset]
Really appreciate your effort, come from v32 tieba, LOL, wondering why my g4 charges very slow. It only charges at the rate of 0.3a and 4.2v which is unbelievable considering the fact that it supports Quick Charge
still error
Octopu25 said:
Hi~ guys, I am an android phone user from China who bought LG G4 Japanese Edition [LG isai vivid V32] last month.
After delete "google play service" in system, then reboot, but the device shows [Security Error Authentication Fail #9]
and automatic started again and again, Ops~ device bricked, GG! :crying:
As we know the resources and softwares are not friendly to LG isai vivid V32, the Firmware is also rare, cos I can't find any tip for LG V32 in XDA,
So it is more difficult for us to save the bricked device.
Due to the [Recovery Mode] still can't solve this problem, here we need to use TOT Firmware to go back to stock,
KDZ is also available to reflash, cos I didn't get the KDZ Files, so I choose TOT to reflash my device.
If your LG V32 device have bootloop or stuck on LG Logo, this method would also help you out.
Now Let me tell you the TOT Method to unbrick your LG isai vivid V32.
Before reflash firmware, you need to download the things below:
1)Download the driver
--[LGUnitedMobileDriver_S52MAN314AP22_ML_WHQL_Ver_3.14.1.exe]
2)Download Both TOT File & DLL File:
--LGV32HL-04-V10o-440-51-OCT-13-2015+0.tot
--LGFLASH_LG_G4_CODEFIRE.dll
3)Download flashtool
--[Setup_LGFlashTool_1.8.1.1023.exe]
4)Download Megalock
--[Megalock.dll]
( I am a new user, due to the policy of XDA forums, so I can not posting outside links,
the softwares which are metioned above, you could google it then download)
Install:
1. Install LGUnitedMobileDriver
2. Install LGFlashtool to C:\
3. Don’t run Flashtool at first, cos you will find that is locked
4. Copy [MegaLock.dll] file to C:\LG\LGFlashtool,
Replace the old MegaLock.dll file to unlock.
5. Extract the TOT file from the Zip,ready for using.
6. Ensure the softwares would work, restart your Windows.
1. Download Mode/Firmware Update
1)power off device
2)press and hold [Vol+] then plug USB cable on connect to pc
3)device shows [Download Mode]
2. Change COM port to 41
1)go to Windows [Device Manager]
2)double click [LGE Mobile USB Serial Port] and tap to [Advanced]
3)change the COM Port to COM 41 then click ok.
4)unplug USB cable but keep device in Download Mode.
3. Import the Firmware
1)Run LG Flashtool
2)in the tool you can see [Model Config]
3)select [Manual Mode],select .dll in files, select TOT Firmware
4)click [Brush Button] change the [LIMO port] to 101
5)on the right side, you could select 1~16 to narrow down the range of searching ports
6)click [ok]
4. Reflash Firmware
1)click the [Yellow Arrow Button]
2)after CRC, tool will show [READY!]
3)plug USB cable to device then the TOT install would be trigged.
4)when process go to about 80%.screens will light up
5)after upload Minios, screen shows in Blue color
6)when flashtool shows [PASS!],it means Success.
Meanwhile screen shows [Factory Reset Statu 3].
5. Reboot
1)unplug USB cable
2)pull battery and reload
3)press power button to Star your device.
PS: If process Failed, I suggest you to unplug USB cable and battery and do this method again.
At last, Here I would like to thank lgviet forum in Vietnam and hyelton who Recognized Contributor on 13th May 2015, 07:07 PM
Click to expand...
Click to collapse
I've tried many times, but still failed, there is a solution?
Same broblem
Same broblem
arfans said:
I've tried many times, but still failed, there is a solution?
Click to expand...
Click to collapse
i have the solution
you can pm / inbox / private messages to me if you want
i have the correct dll for yor lg v32
F.Dhil said:
i have the solution
you can pm / inbox / private messages to me if you want
i have the correct dll for yor lg v32
Click to expand...
Click to collapse
I flash it by octopus box lg software .
Now loop reboot and can't enter download mode
Solusion please
Help me for LG V32 bootlop
Octopu25 said:
Hi~ guys, I am an android phone user from China who bought LG G4 Japanese Edition [LG isai vivid V32] last month.
After delete "google play service" in system, then reboot, but the device shows [Security Error Authentication Fail #9]
and automatic started again and again, Ops~ device bricked, GG! :crying:
As we know the resources and softwares are not friendly to LG isai vivid V32, the Firmware is also rare, cos I can't find any tip for LG V32 in XDA,
So it is more difficult for us to save the bricked device.
Due to the [Recovery Mode] still can't solve this problem, here we need to use TOT Firmware to go back to stock,
KDZ is also available to reflash, cos I didn't get the KDZ Files, so I choose TOT to reflash my device.
If your LG V32 device have bootloop or stuck on LG Logo, this method would also help you out.
Now Let me tell you the TOT Method to unbrick your LG isai vivid V32.
Before reflash firmware, you need to download the things below:
1)Download the driver
--[LGUnitedMobileDriver_S52MAN314AP22_ML_WHQL_Ver_3.14.1.exe]
2)Download Both TOT File & DLL File:
--LGV32HL-04-V10o-440-51-OCT-13-2015+0.tot
--LGFLASH_LG_G4_CODEFIRE.dll
3)Download flashtool
--[Setup_LGFlashTool_1.8.1.1023.exe]
4)Download Megalock
--[Megalock.dll]
( I am a new user, due to the policy of XDA forums, so I can not posting outside links,
the softwares which are metioned above, you could google it then download)
Install:
1. Install LGUnitedMobileDriver
2. Install LGFlashtool to C:\
3. Don’t run Flashtool at first, cos you will find that is locked
4. Copy [MegaLock.dll] file to C:\LG\LGFlashtool,
Replace the old MegaLock.dll file to unlock.
5. Extract the TOT file from the Zip,ready for using.
6. Ensure the softwares would work, restart your Windows.
1. Download Mode/Firmware Update
1)power off device
2)press and hold [Vol+] then plug USB cable on connect to pc
3)device shows [Download Mode]
2. Change COM port to 41
1)go to Windows [Device Manager]
2)double click [LGE Mobile USB Serial Port] and tap to [Advanced]
3)change the COM Port to COM 41 then click ok.
4)unplug USB cable but keep device in Download Mode.
3. Import the Firmware
1)Run LG Flashtool
2)in the tool you can see [Model Config]
3)select [Manual Mode],select .dll in files, select TOT Firmware
4)click [Brush Button] change the [LIMO port] to 101
5)on the right side, you could select 1~16 to narrow down the range of searching ports
6)click [ok]
4. Reflash Firmware
1)click the [Yellow Arrow Button]
2)after CRC, tool will show [READY!]
3)plug USB cable to device then the TOT install would be trigged.
4)when process go to about 80%.screens will light up
5)after upload Minios, screen shows in Blue color
6)when flashtool shows [PASS!],it means Success.
Meanwhile screen shows [Factory Reset Statu 3].
5. Reboot
1)unplug USB cable
2)pull battery and reload
3)press power button to Star your device.
PS: If process Failed, I suggest you to unplug USB cable and battery and do this method again.
At last, Here I would like to thank lgviet forum in Vietnam and hyelton who Recognized Contributor on 13th May 2015, 07:07 PM
Click to expand...
Click to collapse
Halo Brother,
Help me please, my device LG v32 bootlop,
could you give me link for that firmware?
Thanks vv much
STOCK ROM
Hello everyone!
I know this phone barely has stock rom files available for download but I want to know if any of you have the marshmallow version LGV3220g to download.
I'm stuck with 5.1 and I can't even update it on OTA because I'm not in Japan...
After using my cool1 for a month with no problems i decided to flash JUI 7.0.1 (with gapps etc...) on my Cool1 via TWRP but after doing it i realized it has many bugs and apps doesn't work properly. So i decided to return to EUI. After flashing the original stock firmware and rebooting the phone automatically switched off.
Power button not working, i cannot get into recovery and i tried all combinations of buttons without success.
When i connect it to the computer the red led start glowing and my computer recognizes it ONLY in Device Manager as QUALCOMM HS-USB Diagnostic 900E (COM3).
i have all the latest drivers installed.
i tried QFIL and it also recognizes it as QUALCOMM HS-USB Diagnostic 900E (COM3) and after setting everything when i click "Download" i get this error:
Start Download
COM Port number:3
Switch To EDL
Download Fail:Switch To EDL FailFailed to Switch to Emergency Download mode
Finish Download
Click to expand...
Click to collapse
MiFlash doesn't recognize the phone so nothing to do
Coolpad Download Assistant doesn't recognize the phone.
YGDP not working
to flash a new rom i need the phone to go into QUALCOMM HS-USB QDLOADER 9008 MODE but i tried everything installed the latest drivers even bought a 10$ EDL CABLE from amazon still not working always show me QUALCOMM HS-USB Diagnostic 900E
Any suggestion that would help, please... I think it's hard bricked because it cannot get into recovery nor the fastboot mode. completely dead only Red led glowing and QUALCOMM HS-USB Diagnostic 900E (COM3).
Thank you
hi
i installed custom recovery to cool 1 c 103
after it finished model number changed to 106
what i have to do?????
So nobody could help?
hello. probably you wipe system. .. or i dont know..but try this:
Forced writing a recovery mod using QFIL.exe:
a) open program qfil.exe
b) choose the recovery folder and xml file
(remember: for writing succes recovery you need type this command in cmd: BCDEDIT.EXE –SET TESTSIGNING OFF)
c) plug the phone
d) now. most important: Hold Volume up , Volume Down and Power Button At same time. and - always press the button
if not working : first d) and then c) steps.
if the qfil.exe read the phone hold continues button.
e) press download button on qfil.exe
Now in this moment you have a recovery mod.
This method it worked for me
So now you need a flash a rom.
I dont understand why after flash some room(miui 8, 9, etc) my phone did not open..
maybe some rom dont have a kernel
so.. i flash the jui 7 by cuoco and my phone its a live ()
now you can try flash now room (I'm not sure if it will work as I did not try)
1. wipe data and cache
2) flash new rom
edit: dont work flash any rom after flashed jiui..i dont know why......
Edit2: for change jui to eui watch this:
https://youtu.be/oPB1izX4Plo
Good luck:good:
Bogdanm997 said:
hello. probably you wipe system. .. or i dont know..but try this:
Forced writing a recovery mod using QFIL.exe:
a) open program qfil.exe
b) choose the recovery folder and xml file
(remember: for writing succes recovery you need type this command in cmd: BCDEDIT.EXE –SET TESTSIGNING OFF)
c) plug the phone
d) now. most important: Hold Volume up , Volume Down and Power Button At same time. and - always press the button
if not working : first d) and then c) steps.
if the qfil.exe read the phone hold continues button.
e) press download button on qfil.exe
Now in this moment you have a recovery mod.
This method it worked for me
So now you need a flash a rom.
I dont understand why after flash some room(miui 8, 9, etc) my phone did not open..
maybe some rom dont have a kernel
so.. i flash the jui 7 by cuoco and my phone its a live ()
now you can try flash now room (I'm not sure if it will work as I did not try)
1. wipe data and cache
2) flash new rom
edit: dont work flash any rom after flashed jiui..i dont know why......
Good luck:good:
Click to expand...
Click to collapse
I've flashed the recovery mode but my phone is not opening can you help me ? :crying:
silentzer14 said:
I've flashed the recovery mode but my phone is not opening can you help me ? :crying:
Click to expand...
Click to collapse
Edit 3: To change EUI to JUI or viceversa You need use Coolpad download assistant
I found a video yt, link bellow.
Hi, but recovery mod is working? Press Vol up + Power Button to Enter in recovery.
If recovery work, You can flash a rom . Jui or eui.
More details please and i try to help You.
Edit:
Or write rom with coolpad download assistant:
https://youtu.be/oPB1izX4Plo
After You can install recovery
Edit2: I recomanded install trwp 3.1.x.x by @Cuoco92
And then You can Root the phone. (Install magisk or SuperSU from recovery)
Bogdanm997 said:
Edit 3: To change EUI to JUI or viceversa You need use Coolpad download assistant
I found a video yt, link bellow.
Hi, but recovery mod is working? Press Vol up + Power Button to Enter in recovery.
If recovery work, You can flash a rom . Jui or eui.
More details please and i try to help You.
Edit:
Or write rom with coolpad download assistant:
https://youtu.be/oPB1izX4Plo
After You can install recovery
Edit2: I recomanded install trwp 3.1.x.x by @Cuoco92
And then You can Root the phone. (Install magisk or SuperSU from recovery)
Click to expand...
Click to collapse
I have fixed the device but the only problem now is I don't have any signal. Simcards are detected but no Network at ALL, I tried to Fix my IMEI but still the same, do you know how to fix it ?
I also tried to reflash the rom through TWRP still the same -_-
realblackyz said:
After using my cool1 for a month with no problems i decided to flash JUI 7.0.1 (with gapps etc...) on my Cool1 via TWRP but after doing it i realized it has many bugs and apps doesn't work properly. So i decided to return to EUI. After flashing the original stock firmware and rebooting the phone automatically switched off.
Power button not working, i cannot get into recovery and i tried all combinations of buttons without success.
When i connect it to the computer the red led start glowing and my computer recognizes it ONLY in Device Manager as QUALCOMM HS-USB Diagnostic 900E (COM3).
i have all the latest drivers installed.
i tried QFIL and it also recognizes it as QUALCOMM HS-USB Diagnostic 900E (COM3) and after setting everything when i click "Download" i get this error:
MiFlash doesn't recognize the phone so nothing to do
Coolpad Download Assistant doesn't recognize the phone.
YGDP not working
to flash a new rom i need the phone to go into QUALCOMM HS-USB QDLOADER 9008 MODE but i tried everything installed the latest drivers even bought a 10$ EDL CABLE from amazon still not working always show me QUALCOMM HS-USB Diagnostic 900E
Any suggestion that would help, please... I think it's hard bricked because it cannot get into recovery nor the fastboot mode. completely dead only Red led glowing and QUALCOMM HS-USB Diagnostic 900E (COM3).
Thank you
Click to expand...
Click to collapse
Turn off your phone then
Insert the Cable
Hold "VOLUME UP + DOWN + POWER BUTTON" wait until the 4th beep sound Then try to flash again.
I didnt get this problem, I dont know exactly how to fix, but try:
https://youtu.be/9mbNvItVg78
https://youtu.be/8QZF_H_JNpA
silentzer14 said:
Turn off your phone then
Insert the Cable
Hold "VOLUME UP + DOWN + POWER BUTTON" wait until the 4th beep sound Then try to flash again.
Click to expand...
Click to collapse
Unfortunately it isn't working just tried
Try Vol Up + Down + Usb Cable , to get into 9008 Mode.
dwaipayan774 said:
Try Vol Up + Down + Usb Cable , to get into 9008 Mode.
Click to expand...
Click to collapse
USB cable?sorry What's 9008 mode..
bigdoomzoe said:
USB cable?sorry What's 9008 mode..
Click to expand...
Click to collapse
Qualcomm HS- Usb 9008 mode .
Press vol up and down and plug in the usb cable while connected to PC.
What program is needed for the computer
bigdoomzoe said:
What program is needed for the computer
Click to expand...
Click to collapse
---------- Post added at 08:43 AM ---------- Previous post was at 08:42 AM ----------
bigdoomzoe said:
What program is needed for the computer
Click to expand...
Click to collapse
QFIL or HQXA
This will unlock my network
I try it but when i do the recovery mode only the red light is working the phone isn't vibrate and nothing so i tried to do it in the YGDP tool and isn't working too are you know anoyher way ?? :crying:
Boulfalxd said:
I try it but when i do the recovery mode only the red light is working the phone isn't vibrate and nothing so i tried to do it in the YGDP tool and isn't working too are you know anoyher way ?? :crying:
Click to expand...
Click to collapse
Try QGDP. On my Pc my phone is not detected by YGDP ,but I can flash stock ROM with QGDP.You can flash with QGDP , without even turning on the phone.Add the CPB file in QGDP, click start, and then plug in phone while switched off(no need to press any button)
Man you're my hero ;b
Boulfalxd said:
Man you're my hero ;b
Click to expand...
Click to collapse
If you were able to flash Stock ROM,then Congratulations.
Hi all.
I´m still searching some way to solve my problem.
What´s happaned:
was on AEX OREO, make downgrade to SLIM stock 7.1 from raystef66 = all ok. But after a couple days made magisk upgrade to 17 via twrp and after that is "death"...when I try to start my phone I can see first ZTE logo, than 3x red led, that´s all, I think after flash stockrom I lost customrecovery......?.....t I can not start to TWRP, FASTBOOD...maybe EDL working but:
When I try combo+pwr I see DFU/com4 port. So I tried guidef from raystef66 with ZTE DFU_MultiDL_A2017X_Tool = apk see my phone but still in disconect mode(conect stat) but WIN see my phone as HS USB QDlouder 9008 com 8, now I run edl tool from djkuz.
Tool see my phone, name QUALCOM HS=USB QDlouader 9008 and I tried flash edl or recovery with error = from log:
Did not receive Sahara hello packet from device miflash says can not recivie hallo pocaked.
Any new idea how to fix...?
Thx!!
trying on WIN7 pro
kraljan66 said:
Hi all.
I´m still searching some way to solve my problem.
What´s happaned:
was on AEX OREO, make downgrade to SLIM stock 7.1 from raystef66 = all ok. But after a couple days made magisk upgrade to 17 via twrp and after that is "death"...when I try to start my phone I can see first ZTE logo, than 3x red led, that´s all, I think after flash stockrom I lost customrecovery......?.....t I can not start to TWRP, FASTBOOD...maybe EDL working but:
When I try combo+pwr I see DFU/com4 port. So I tried guidef from raystef66 with ZTE DFU_MultiDL_A2017X_Tool = apk see my phone but still in disconect mode(conect stat) but WIN see my phone as HS USB QDlouder 9008 com 8, now I run edl tool from djkuz.
Tool see my phone, name QUALCOM HS=USB QDlouader 9008 and I tried flash edl or recovery with error = from log:
Did not receive Sahara hello packet from device miflash says can not recivie hallo pocaked.
Any new idea how to fix...?
Thx!!
trying on WIN7 pro
Click to expand...
Click to collapse
First: did the DFU see a com port in the config?
You do have to select the com port manually.
Second: can you boot to FTM?
Third: try another Edl package, some Edl have to be installed as a backup restore not via a straight flashing.
thx for quick answer!
1 see pic pls, in DFU com4
2 no can not get to FTM
3 tried 3x another packages...see log/pic from ZTE EDL tool...
kraljan66 said:
thx for quick answer!
1 see pic pls, in DFU com4
2 no can not get to FTM
3 tried 3x another packages...see log/pic from ZTE EDL tool...
Click to expand...
Click to collapse
Use the latest MiFlash. I've been having trouble with EDL Tool lately. Maybe it'll work. z
I'm guessing the red LED turns off as soon as you connect MultiDL correctly?
Make sure Edl tool is in the root directory of you PC or laptop drive.
EG: C:\ or D:\ as per the instructions.
Make sure you run it as admin too.
If I remember correctly the full Edl package had to be placed into the appropriate folder as per instruction (via the tool) and on the post.
@Syberclone:
I have all as you write...in root, edl package is correct/about edl package edl tool says "success = tried 4different edl package for my phone"/
I´m convinced about a port problem, log from edl tool is:
15:47:25: INFO: User wants to talk to port '\\.\COM8'
ERROR
15:47:25: {ERROR: OpenPort:5198 Failed to open com port '\\.\COM8'
I´ll try another miflash but dont believe ...:-/
just used another PC with WIN7 and now.....CHEEEEERS!!!!!!
Thx to all!