The help, please! Constantly continued bootloop
There is an insertion, the programmed equipment for FlashTool or Odin
Huawei G7_L01?
I can not come in Fastboot
download ur offcial rom and put in dload folder on ur sdcard. power off ur device and hold power + vol up + vol down and wait until the instalation finish and supposedly it will restored back ur bootloader
Ascend G7-L01 doesn't boot
Hi,
I have the same problem after upgrading my G7-L01 by putting dload in SDcard.
The MUI update started and finished 100% but the phone become bricked!
It is detected as "RELINK HS-USB QDLoader 9008 (Port16)".
I think that I must flash now with SP Flash Tool or other tool! But I didn't find a ROM for that (with scatter).
Thanks for help!
hosnix said:
Hi,
I have the same problem after upgrading my G7-L01 by putting dload in SDcard.
The MUI update started and finished 100% but the phone become bricked!
It is detected as "RELINK HS-USB QDLoader 9008 (Port16)".
I think that I must flash now with SP Flash Tool or other tool! But I didn't find a ROM for that (with scatter).
Thanks for help!
Click to expand...
Click to collapse
i have the same scenario. my phone still bricked. did find any solution to make it boot again ?
Related
Hi All,
I need help to bring back my Asus Zenfone 2 Laser ze550kl from dead condition, I can't enter fastboot mode to flash any ROM also. Device manager only shows "Qualcomm HS-USB QDLoader 9008 (COM3)" under Ports section. After searching online, I found a link to recover it, but it needs certain files which I could not find in web. The files required are:
rawprogram0.xml
patch0.xml
for ze550kl. I have installed QPST 2.7 Qualcomm tool, and additinally need the complete EMMC image.
https://devlakiutak.wordpress.com/2013/08/10/fixdeadboot/
Can someone please help ?
Thanks
gurung_vishwas1 said:
Hi All,
I need help to bring back my Asus Zenfone 2 Laser ze550kl from dead condition, I can't enter fastboot mode to flash any ROM also. Device manager only shows "Qualcomm HS-USB QDLoader 9008 (COM3)" under Ports section. After searching online, I found a link to recover it, but it needs certain files which I could not find in web. The files required are:
rawprogram0.xml
patch0.xml
for ze550kl. I have installed QPST 2.7 Qualcomm tool, and additinally need the complete EMMC image.
https://devlakiutak.wordpress.com/2013/08/10/fixdeadboot/
Can someone please help ?
Thanks
Click to expand...
Click to collapse
if your mobile is turning then surely u can enter the fastboot mode, bsc i hav faced it too
Here you have another tutorial: http://www.droidsavvy.com/unbrick-qualcomm-mobiles/
Someone said it the comments that you will find rawprogram0.xml patch0.xml and file after you extract them from the ROM.
Here is the stock marshmallow ROM: https://www.asus.com/support/Download/39/1/0/22/ZROQURlyupei1ZQz/32/
The same happens to me, trying to unlock the bootloader phone. I've sended my phone to warranty and they opened the phone to fix
Sorry for bad english
Good luck
gurung_vishwas1 said:
Hi All,
I need help to bring back my Asus Zenfone 2 Laser ze550kl from dead condition, I can't enter fastboot mode to flash any ROM also. Device manager only shows "Qualcomm HS-USB QDLoader 9008 (COM3)" under Ports section. After searching online, I found a link to recover it, but it needs certain files which I could not find in web. The files required are:
rawprogram0.xml
patch0.xml
for ze550kl. I have installed QPST 2.7 Qualcomm tool, and additinally need the complete EMMC image.
https://devlakiutak.wordpress.com/2013/08/10/fixdeadboot/
Can someone please help ?
Thanks
Click to expand...
Click to collapse
colonho said:
The same happens to me, trying to unlock the bootloader phone. I've sended my phone to warranty and they opened the phone to fix
Sorry for bad english
Good luck
Click to expand...
Click to collapse
Thanks for reply. I think that is the last option which I have now. I was trying to correct it myself, but can't unless I have at least FASTBOOT working.
Fastboot erase config....
After that I stucked at boot logo
Used xfstk then aft but stucked at boot used fastboot commands for flashing system all gonna smooth but stucked at boot...
Used recovery to sideload marshmallow ... succeed. But also stucked at boot ..unlock boot loader flash TWRP flashing custom rom also stucked at boot logo... PLZZ help me guyzzz
And it shows error in TWRP
Unable:to mount Config(invalid argument)
Hi there!!!
My OP5 is full dead!!! Black screen, no charging, no buttons !!!
That why ive tried change rom, flashed via twrp installed!!!
I think the good thing is PC can recognize because device in the Qualcomm HS-USB Qdloader 9008 /EDL mode.
I have tried unbrick it, using this tools
QFIL
Q phone download tool
eMMC DL TOOL
Xiaomi Mi Flas Tool
But....................I NEED A STOCK ROM MUST HAVE
“rawprogram0.XML”, “patch0.XML”, “prog_emmc_firehose_8974.mbn” and “MPRG8974.mbn” flashers . ETC, ETC
BECAUSE
OnePlus5OXYGEN_23_OTA_009_all_1707032123_c10521d0fb8b46c0. ZIP
is missing that kind of files.
DOES SOMEBODY CAN TELL ME WHERE CAN I GET THIS KIND OF ROM FOR OP5!!!????
HELP HELP
Get it from the official site
After using my cool1 for a month with no problems i decided to flash JUI 7.0.1 (with gapps etc...) on my Cool1 via TWRP but after doing it i realized it has many bugs and apps doesn't work properly. So i decided to return to EUI. After flashing the original stock firmware and rebooting the phone automatically switched off.
Power button not working, i cannot get into recovery and i tried all combinations of buttons without success.
When i connect it to the computer the red led start glowing and my computer recognizes it ONLY in Device Manager as QUALCOMM HS-USB Diagnostic 900E (COM3).
i have all the latest drivers installed.
i tried QFIL and it also recognizes it as QUALCOMM HS-USB Diagnostic 900E (COM3) and after setting everything when i click "Download" i get this error:
Start Download
COM Port number:3
Switch To EDL
Download Fail:Switch To EDL FailFailed to Switch to Emergency Download mode
Finish Download
Click to expand...
Click to collapse
MiFlash doesn't recognize the phone so nothing to do
Coolpad Download Assistant doesn't recognize the phone.
YGDP not working
to flash a new rom i need the phone to go into QUALCOMM HS-USB QDLOADER 9008 MODE but i tried everything installed the latest drivers even bought a 10$ EDL CABLE from amazon still not working always show me QUALCOMM HS-USB Diagnostic 900E
Any suggestion that would help, please... I think it's hard bricked because it cannot get into recovery nor the fastboot mode. completely dead only Red led glowing and QUALCOMM HS-USB Diagnostic 900E (COM3).
Thank you
hi
i installed custom recovery to cool 1 c 103
after it finished model number changed to 106
what i have to do?????
So nobody could help?
hello. probably you wipe system. .. or i dont know..but try this:
Forced writing a recovery mod using QFIL.exe:
a) open program qfil.exe
b) choose the recovery folder and xml file
(remember: for writing succes recovery you need type this command in cmd: BCDEDIT.EXE –SET TESTSIGNING OFF)
c) plug the phone
d) now. most important: Hold Volume up , Volume Down and Power Button At same time. and - always press the button
if not working : first d) and then c) steps.
if the qfil.exe read the phone hold continues button.
e) press download button on qfil.exe
Now in this moment you have a recovery mod.
This method it worked for me
So now you need a flash a rom.
I dont understand why after flash some room(miui 8, 9, etc) my phone did not open..
maybe some rom dont have a kernel
so.. i flash the jui 7 by cuoco and my phone its a live ()
now you can try flash now room (I'm not sure if it will work as I did not try)
1. wipe data and cache
2) flash new rom
edit: dont work flash any rom after flashed jiui..i dont know why......
Edit2: for change jui to eui watch this:
https://youtu.be/oPB1izX4Plo
Good luck:good:
Bogdanm997 said:
hello. probably you wipe system. .. or i dont know..but try this:
Forced writing a recovery mod using QFIL.exe:
a) open program qfil.exe
b) choose the recovery folder and xml file
(remember: for writing succes recovery you need type this command in cmd: BCDEDIT.EXE –SET TESTSIGNING OFF)
c) plug the phone
d) now. most important: Hold Volume up , Volume Down and Power Button At same time. and - always press the button
if not working : first d) and then c) steps.
if the qfil.exe read the phone hold continues button.
e) press download button on qfil.exe
Now in this moment you have a recovery mod.
This method it worked for me
So now you need a flash a rom.
I dont understand why after flash some room(miui 8, 9, etc) my phone did not open..
maybe some rom dont have a kernel
so.. i flash the jui 7 by cuoco and my phone its a live ()
now you can try flash now room (I'm not sure if it will work as I did not try)
1. wipe data and cache
2) flash new rom
edit: dont work flash any rom after flashed jiui..i dont know why......
Good luck:good:
Click to expand...
Click to collapse
I've flashed the recovery mode but my phone is not opening can you help me ? :crying:
silentzer14 said:
I've flashed the recovery mode but my phone is not opening can you help me ? :crying:
Click to expand...
Click to collapse
Edit 3: To change EUI to JUI or viceversa You need use Coolpad download assistant
I found a video yt, link bellow.
Hi, but recovery mod is working? Press Vol up + Power Button to Enter in recovery.
If recovery work, You can flash a rom . Jui or eui.
More details please and i try to help You.
Edit:
Or write rom with coolpad download assistant:
https://youtu.be/oPB1izX4Plo
After You can install recovery
Edit2: I recomanded install trwp 3.1.x.x by @Cuoco92
And then You can Root the phone. (Install magisk or SuperSU from recovery)
Bogdanm997 said:
Edit 3: To change EUI to JUI or viceversa You need use Coolpad download assistant
I found a video yt, link bellow.
Hi, but recovery mod is working? Press Vol up + Power Button to Enter in recovery.
If recovery work, You can flash a rom . Jui or eui.
More details please and i try to help You.
Edit:
Or write rom with coolpad download assistant:
https://youtu.be/oPB1izX4Plo
After You can install recovery
Edit2: I recomanded install trwp 3.1.x.x by @Cuoco92
And then You can Root the phone. (Install magisk or SuperSU from recovery)
Click to expand...
Click to collapse
I have fixed the device but the only problem now is I don't have any signal. Simcards are detected but no Network at ALL, I tried to Fix my IMEI but still the same, do you know how to fix it ?
I also tried to reflash the rom through TWRP still the same -_-
realblackyz said:
After using my cool1 for a month with no problems i decided to flash JUI 7.0.1 (with gapps etc...) on my Cool1 via TWRP but after doing it i realized it has many bugs and apps doesn't work properly. So i decided to return to EUI. After flashing the original stock firmware and rebooting the phone automatically switched off.
Power button not working, i cannot get into recovery and i tried all combinations of buttons without success.
When i connect it to the computer the red led start glowing and my computer recognizes it ONLY in Device Manager as QUALCOMM HS-USB Diagnostic 900E (COM3).
i have all the latest drivers installed.
i tried QFIL and it also recognizes it as QUALCOMM HS-USB Diagnostic 900E (COM3) and after setting everything when i click "Download" i get this error:
MiFlash doesn't recognize the phone so nothing to do
Coolpad Download Assistant doesn't recognize the phone.
YGDP not working
to flash a new rom i need the phone to go into QUALCOMM HS-USB QDLOADER 9008 MODE but i tried everything installed the latest drivers even bought a 10$ EDL CABLE from amazon still not working always show me QUALCOMM HS-USB Diagnostic 900E
Any suggestion that would help, please... I think it's hard bricked because it cannot get into recovery nor the fastboot mode. completely dead only Red led glowing and QUALCOMM HS-USB Diagnostic 900E (COM3).
Thank you
Click to expand...
Click to collapse
Turn off your phone then
Insert the Cable
Hold "VOLUME UP + DOWN + POWER BUTTON" wait until the 4th beep sound Then try to flash again.
I didnt get this problem, I dont know exactly how to fix, but try:
https://youtu.be/9mbNvItVg78
https://youtu.be/8QZF_H_JNpA
silentzer14 said:
Turn off your phone then
Insert the Cable
Hold "VOLUME UP + DOWN + POWER BUTTON" wait until the 4th beep sound Then try to flash again.
Click to expand...
Click to collapse
Unfortunately it isn't working just tried
Try Vol Up + Down + Usb Cable , to get into 9008 Mode.
dwaipayan774 said:
Try Vol Up + Down + Usb Cable , to get into 9008 Mode.
Click to expand...
Click to collapse
USB cable?sorry What's 9008 mode..
bigdoomzoe said:
USB cable?sorry What's 9008 mode..
Click to expand...
Click to collapse
Qualcomm HS- Usb 9008 mode .
Press vol up and down and plug in the usb cable while connected to PC.
What program is needed for the computer
bigdoomzoe said:
What program is needed for the computer
Click to expand...
Click to collapse
---------- Post added at 08:43 AM ---------- Previous post was at 08:42 AM ----------
bigdoomzoe said:
What program is needed for the computer
Click to expand...
Click to collapse
QFIL or HQXA
This will unlock my network
I try it but when i do the recovery mode only the red light is working the phone isn't vibrate and nothing so i tried to do it in the YGDP tool and isn't working too are you know anoyher way ?? :crying:
Boulfalxd said:
I try it but when i do the recovery mode only the red light is working the phone isn't vibrate and nothing so i tried to do it in the YGDP tool and isn't working too are you know anoyher way ?? :crying:
Click to expand...
Click to collapse
Try QGDP. On my Pc my phone is not detected by YGDP ,but I can flash stock ROM with QGDP.You can flash with QGDP , without even turning on the phone.Add the CPB file in QGDP, click start, and then plug in phone while switched off(no need to press any button)
Man you're my hero ;b
Boulfalxd said:
Man you're my hero ;b
Click to expand...
Click to collapse
If you were able to flash Stock ROM,then Congratulations.
Hi all.
I´m still searching some way to solve my problem.
What´s happaned:
was on AEX OREO, make downgrade to SLIM stock 7.1 from raystef66 = all ok. But after a couple days made magisk upgrade to 17 via twrp and after that is "death"...when I try to start my phone I can see first ZTE logo, than 3x red led, that´s all, I think after flash stockrom I lost customrecovery......?.....t I can not start to TWRP, FASTBOOD...maybe EDL working but:
When I try combo+pwr I see DFU/com4 port. So I tried guidef from raystef66 with ZTE DFU_MultiDL_A2017X_Tool = apk see my phone but still in disconect mode(conect stat) but WIN see my phone as HS USB QDlouder 9008 com 8, now I run edl tool from djkuz.
Tool see my phone, name QUALCOM HS=USB QDlouader 9008 and I tried flash edl or recovery with error = from log:
Did not receive Sahara hello packet from device miflash says can not recivie hallo pocaked.
Any new idea how to fix...?
Thx!!
trying on WIN7 pro
kraljan66 said:
Hi all.
I´m still searching some way to solve my problem.
What´s happaned:
was on AEX OREO, make downgrade to SLIM stock 7.1 from raystef66 = all ok. But after a couple days made magisk upgrade to 17 via twrp and after that is "death"...when I try to start my phone I can see first ZTE logo, than 3x red led, that´s all, I think after flash stockrom I lost customrecovery......?.....t I can not start to TWRP, FASTBOOD...maybe EDL working but:
When I try combo+pwr I see DFU/com4 port. So I tried guidef from raystef66 with ZTE DFU_MultiDL_A2017X_Tool = apk see my phone but still in disconect mode(conect stat) but WIN see my phone as HS USB QDlouder 9008 com 8, now I run edl tool from djkuz.
Tool see my phone, name QUALCOM HS=USB QDlouader 9008 and I tried flash edl or recovery with error = from log:
Did not receive Sahara hello packet from device miflash says can not recivie hallo pocaked.
Any new idea how to fix...?
Thx!!
trying on WIN7 pro
Click to expand...
Click to collapse
First: did the DFU see a com port in the config?
You do have to select the com port manually.
Second: can you boot to FTM?
Third: try another Edl package, some Edl have to be installed as a backup restore not via a straight flashing.
thx for quick answer!
1 see pic pls, in DFU com4
2 no can not get to FTM
3 tried 3x another packages...see log/pic from ZTE EDL tool...
kraljan66 said:
thx for quick answer!
1 see pic pls, in DFU com4
2 no can not get to FTM
3 tried 3x another packages...see log/pic from ZTE EDL tool...
Click to expand...
Click to collapse
Use the latest MiFlash. I've been having trouble with EDL Tool lately. Maybe it'll work. z
I'm guessing the red LED turns off as soon as you connect MultiDL correctly?
Make sure Edl tool is in the root directory of you PC or laptop drive.
EG: C:\ or D:\ as per the instructions.
Make sure you run it as admin too.
If I remember correctly the full Edl package had to be placed into the appropriate folder as per instruction (via the tool) and on the post.
@Syberclone:
I have all as you write...in root, edl package is correct/about edl package edl tool says "success = tried 4different edl package for my phone"/
I´m convinced about a port problem, log from edl tool is:
15:47:25: INFO: User wants to talk to port '\\.\COM8'
ERROR
15:47:25: {ERROR: OpenPort:5198 Failed to open com port '\\.\COM8'
I´ll try another miflash but dont believe ...:-/
just used another PC with WIN7 and now.....CHEEEEERS!!!!!!
Thx to all!
Dear Yureka Users,
If you have hardbricked your YU Yureka A05510 during flashing , modifying or other high level engineering , There is a detailed process how to revive it back to the STOCK 5.1 Lollipop Rom.
""This method is different from SD Card partitioning using windisk""
Requirements
1. A Yu Yureka ao5510 ( Hardbricked )
2. A Windows Based PC
3. Files Provided by me
4. A working Brain
5. A lots of patience
This Guide is only for the advance users & i hope you have installed all the FASTBOOT , ADB , HS-USB QDloader 9008 drivers.
( For noobs ) you are requested to contact me on [email protected] . . Because you need personal assistance.
[[Warning]] I request you to please use the files & tools provided by me ,, any other combination of softwares & files result into sahara Fail error
Follow the following steps to Revive your Device.
1. Install all the appropriate drivers Needed like Fastboot , ADB & HS-usb qdloader 9008 etc. ( Updated )
2. Download the YU revive kit.zip attached.
3. Connect the Yureka to PC by Usb Data cable & boot it into the HS-USB qdloader 9008 Mode by Shorting the pins 2 & 4.
4. Extract the contents of the ZIP into separate folder.
5. Right click Qfil.exe and Run as administrator.
6. you device should be detected by Qfil as HS-USB Qdloader 9008 [COM x] , where x is the PORT assigned to your device .
7 . Now Select the programmer in Qfil tool prog_emmc_firehose.mbn ( Don,t choose prog_emmc_firehose_8936.mbn )
8. Now click on Load XML & select RAWPROGRAM0.xml & PATCH0.xml provided in the zip file.
9. Click on download.
10 . Wait unlit "" waiting for the phone to reset "" is shown in the log.
11. Now Remove Battery wait for 1 minute & Re-insert it.
12. Now press hold volume UP + button & insert PC USB cable again . It will boot into the fastboot mode .
13. now click on the flashall(afterqfil).bat provided in zip , It will reconstruct your all partitions.
14. After ""flashall(afterqfil).bat"" successfully finished . CLick on Flashall.bat provided in zip.
15. Your device will boot normally to CYNOGEN LOLLIPOP OS. You can use SN writer to fix your corrupted IMEI no. .... SM writer is also provided in that ZIP file.
{{{ if i helped you please press the thanks button }}}
or contact me on [email protected]
nice
Where is the attachment?
Where are the files..!!!