I ordered a $2.15 LOCA tempered glass screen protector on Aliexpress. Purchased 08/28 and received it today 09/17. I live in San Francisco. Overall the quality of the screen is pretty much the same as the Whitestone. This one doesn't come with the plastic alignment case that the Whitestone comes with, but you get a UV light and single bottle of glue. I used the same procedure as Whitestone but just without the guide. Also you don't get any tapes to protect the USB ports, etc. I just cut some packing tape and covered those up. I did ok, there is a small air bubble at the bottom. I hope it slowly cures over time. My experience with Whitestone is that you don't want to push and squeeze too hard. You can barely notice it when screen is on, but I'm kind of OCD so I ordered another and may swap it.
So if you have experience and can wait (Note 10/10+ comes with a screen protector), save some money. BTW, finger print works just fine.
Aliexpress Link
is that an Spigen tough armor case?
cheers
Same experience. Nothing fancy, but it gets the job done. Just tape over the speakers. There are some on ebay for a similar price if you don't like using Ali for some reason.
Whitestone and AMFILM are good if you need to be spoon fed.
*looks at my Whitestone with no bubbles* Hmmm... Maybe being "spoon-fed" isn't so bad.
Mr. Orange 645 said:
*looks at my Whitestone with no bubbles* Hmmm... Maybe being "spoon-fed" isn't so bad.
Click to expand...
Click to collapse
I had bubble with my first Whitestone. I think having the guide cage helps but if you have experience, it's not necessary. There is just some luck to it.
Sent from my SM-N975U using Tapatalk
gordec said:
I had bubble with my first Whitestone. I think having the guide cage helps but if you have experience, it's not necessary. There is just some luck to it.
Sent from my SM-N975U using Tapatalk
Click to expand...
Click to collapse
I've installed quite a few LOCA TGSPs. Some I bought LOCA separate and then bought a TGSP and made my own kit. Worked great, was messy AF to install, cause I had NO idea how much to use, LOL. and they all chipped and cracked in a week or two.
I've also bought some cheaper kits that included the right amount of LOCA and a TGSP. They ended up lifting on the edges. Last one I tried was Note 9.
I wound buying a second used Note 9 that already had Whitestone Dome installed by the previous owner, and I loved it. So when I pre-ordered my Note 10+, I pre-ordered a Whitestone Dome for it. Sucked paying over $40, but honestly, I've spent hundreds in the past trying to find the "perfect" screen protector. Don't regret Whitestone or the money spent at all. And the installation tray made it dead simple. It was worth it to get it right the first time.
If I had to change TGSPs, if go with AmFilm, just because they're also getting great reviews are basically half the price. Or I'd go back to a soft screen protector, the Ringke Dual Easy Film. It's just basically invisible.
Mr. Orange 645 said:
I've installed quite a few LOCA TGSPs. Some I bought LOCA separate and then bought a TGSP and made my own kit. Worked great, was messy AF to install, cause I had NO idea how much to use, LOL. and they all chipped and cracked in a week or two.
I've also bought some cheaper kits that included the right amount of LOCA and a TGSP. They ended up lifting on the edges. Last one I tried was Note 9.
I wound buying a second used Note 9 that already had Whitestone Dome installed by the previous owner, and I loved it. So when I pre-ordered my Note 10+, I pre-ordered a Whitestone Dome for it. Sucked paying over $40, but honestly, I've spent hundreds in the past trying to find the "perfect" screen protector. Don't regret Whitestone or the money spent at all. And the installation tray made it dead simple. It was worth it to get it right the first time.
If I had to change TGSPs, if go with AmFilm, just because they're also getting great reviews are basically half the price. Or I'd go back to a soft screen protector, the Ringke Dual Easy Film. It's just basically invisible.
Click to expand...
Click to collapse
Soft ones are uncomfortable with spen right? I tried one for the Note 9.
Sent from my SM-N975U using Tapatalk
gordec said:
Soft ones are uncomfortable with spen right? I tried one for the Note 9.
Sent from my SM-N975U using Tapatalk
Click to expand...
Click to collapse
Depends on which one you buy the wet install ones typically suck to use with the SPen. The Ringke was awesome. Couldn't tell it was there, even with the SPen. I honestly can't speak highly enough of them. They honestly feel like glass.
Thanks. Bought one to try.
Sent from my SM-N975U using Tapatalk
Mr. Orange 645 said:
Depends on which one you buy the wet install ones typically suck to use with the SPen. The Ringke was awesome. Couldn't tell it was there, even with the SPen. I honestly can't speak highly enough of them. They honestly feel like glass.
Click to expand...
Click to collapse
Installed it. I like it. It's not glass but very smooth with Spen. The extreme edges has slight lift but very mild. Not sure if you had some tricks to get all the edges to stay down.
gordec said:
Installed it. I like it. It's not glass but very smooth with Spen. The extreme edges has slight lift but very mild. Not sure if you had some tricks to get all the edges to stay down.
Click to expand...
Click to collapse
I haven't tried one on my N10+, but installed them on my Note 9 and my wife's S10+. Neither one had any issues with the edges lifting at all. I wish I had some tricks to offer, but I just followed the directions.
It's funny, when I installed my wife's Ringke on her S10+ I was showing her the difference between it and the Whitestone Dome tempered glass (which are the time was on my Note 9). I was showing her how glass was smoother than her Ringke protector, but to my surprise, my finger actually glided easier across her Ringke than my Whitestone! Now my Whitestone Dome on that phone was a few months old, so some of the oleophobic coating had probably worn off and her Ringke screen protector was brand new, but I was really shocked and just how smooth it was to the touch.
As far as the lifting edges, two thoughts. One, you didn't get it lined up perfectly so maybe something is a little off? A half millimeter either way could make it uneven. But I don't think thats the issue. Two, perhaps the edges of your phone weren't clean enough and had some residual oils? Or three, you just got a faulty screen protector. If it gets worse, try the second one in the pack. If that fails, reach out to Ringke and they should replace it for free.
Mr. Orange 645 said:
I haven't tried one on my N10+, but installed them on my Note 9 and my wife's S10+. Neither one had any issues with the edges lifting at all. I wish I had some tricks to offer, but I just followed the directions.
It's funny, when I installed my wife's Ringke on her S10+ I was showing her the difference between it and the Whitestone Dome tempered glass (which are the time was on my Note 9). I was showing her how glass was smoother than her Ringke protector, but to my surprise, my finger actually glided easier across her Ringke than my Whitestone! Now my Whitestone Dome on that phone was a few months old, so some of the oleophobic coating had probably worn off and her Ringke screen protector was brand new, but I was really shocked and just how smooth it was to the touch.
As far as the lifting edges, two thoughts. One, you didn't get it lined up perfectly so maybe something is a little off? A half millimeter either way could make it uneven. But I don't think thats the issue. Two, perhaps the edges of your phone weren't clean enough and had some residual oils? Or three, you just got a faulty screen protector. If it gets worse, try the second one in the pack. If that fails, reach out to Ringke and they should replace it for free.
Click to expand...
Click to collapse
The lift is really very minor. Only the most OCD types will mind. Thanks for the rec. I agree how easy it's to glide your finger on it. Finger print also works better.
gordec said:
The lift is really very minor. Only the most OCD types will mind. Thanks for the rec. I agree how easy it's to glide your finger on it. Finger print also works better.
Click to expand...
Click to collapse
I installed Whitestone on my N10+, but bought a pack of Ringke as a back up. Crack the Whitestone, I can install the Ringke while waiting on a replacement.
But, I think what I'll do is next paycheck, I'm going to order the AmFilm LOCA screen protector and run a little comparison.
I've used Whitestone for a month now and am pleased, but I do think it made the FP sensor less accurate But I'll remove it and install the Ringke and see how I like it, especially with the fingerprint sensor.
I'll use that for a couple weeks then install the AmFilm tempered glass one and compare it to the others.
It means a waste of $40, but in the name of inaccurate anecdotal science, why not? And if I decide I prefer Whitestone after all, it's just a $10 replacement under warranty to go back to it. I'll post my results in a thread here, maybe with some pictures.
Sorry, I know that had nothing to do with your lifting edges. Just thinking out loud. And by out loud, I mean in silence and just typing it.
The lifting edges of ringke, when I installed on my s10+, I found it best to work them down initially then just wait a while before trying again. I waited around 30 mins to 1hr after fitting it and found they stuck down easily.
I struggled with the 1st protector so discarded it but using the waiting method, the 2nd protector sides stayed down.
If you like the original screen protector you can get OEM quality screen protectors cheap on eBay. You want ones made out of PET which are harder like the OEM ones and not the soft TPU ones that you have to install wet and they dent way too easily. I install the PET ones wet though as you have time to move it around on the screen to get it aligned perfectly and you just push out the solution (I spray purple cleaner on the screen before I install) and any dust is removed when you push out the solution.
Just installed one myself that came from aliexpress. It turned out fine but was a bit disappointed that the glass is curvy on the edges like an s10 rather than being "boxy" so the edges are a bit exposed. Can't be bothered though to buy another one and go through the installation again as it took quite some time to get it done. Fingerprint is working fine, just press the fingerprint area while curing for the first time.
ajsmsg78 said:
If you like the original screen protector you can get OEM quality screen protectors cheap on eBay. You want ones made out of PET which are harder like the OEM ones and not the soft TPU ones that you have to install wet and they dent way too easily. I install the PET ones wet though as you have time to move it around on the screen to get it aligned perfectly and you just push out the solution (I spray purple cleaner on the screen before I install) and any dust is removed when you push out the solution.
Click to expand...
Click to collapse
I thought using a wet solution would make the glue not stick anymore for the PET types. Also I was told by Samsung that the stock screen protector is applied with a UV light to cure. So it's like a tempered glass install but a thin plastic type?
fusiondynamics said:
I thought using a wet solution would make the glue not stick anymore for the PET types. Also I was told by Samsung that the stock screen protector is applied with a UV light to cure. So it's like a tempered glass install but a thin plastic type?
Click to expand...
Click to collapse
The adhesive will stick fine on the protector even if you install it wet. I do it all the time.
what is the price this protector?
protector price,?
ajsmsg78 said:
The adhesive will stick fine on the protector even if you install it wet. I do it all the time.
Click to expand...
Click to collapse
What do you use, just water or lightly soapy solution?
Related
Can't find any ones that I like so far. I know the edge makes things difficult but all the glass one I've seen don't have adhesive all over just along the edge and the film one i bought doesn't stay down on the edge so has anyone found a good one or decent one?
Please specify it's full coverage...glass or film...works with case and of so what case
flimflam06 said:
Can't find any ones that I like so far. I know the edge makes things difficult but all the glass one I've seen don't have adhesive all over just along the edge and the film one i bought doesn't stay down on the edge so has anyone found a good one or decent one?
Please specify it's full coverage...glass or film...works with case and of so what case
Click to expand...
Click to collapse
I try using the screen protector that came with the ghostek case I bought install it cover the entire front area of phone plus edges let set for about an hour try to put case on but everytime I did it would lift off the sides of the screen protector so I just took off the screen protector till I find that works. Also try the supershieldz ones same thing.
This is the one I am going to get https://www.amazon.com/dp/B01G7LQZW...TF8&colid=38DVAL1VV0RQM&coliid=I2N75A0MPNERT6
Omega Ra said:
This is the one I am going to get https://www.amazon.com/dp/B01G7LQZW...TF8&colid=38DVAL1VV0RQM&coliid=I2N75A0MPNERT6
Click to expand...
Click to collapse
I was thinking about that one but im not sure about the wet install. I'm good at putting screen protectors on but I've never did a wet install before...i May have to check it out
If you have some time and patience go for the Invisible Shield hd dry full body coverage. I originally ordered a Naked skin from slickwraps but its been processing since the 18th. So when my N7 arrived today I went on the search around town and ended up in a Verizon store. They kindly put it on for me, took two tries lol. Mid-install the Verizon guy just rips it and balls it up and went to grab another. When I got home I went through the packaging and noticed he skimmed me on the install. and didn't install the back.. I tell you what that was the worst torture in my life but hey pics below! Came out beautiful. +extra dbrand lens laying around conveniently . :good: winning
I put on a IQ shield matte. I like the matte finish but it is not for everyone. There is some lost clarity but much less glare and no fingerprints. I like the wet install for no bubbles and being easy. It takes some time to let the edges dry so they will stick. Let it sit at least overnight before using or putting on a case.
My case (Spigen Ultra Hybrid)did cause the corners to lift, a common problem with cases. IQ Shield has since come out with a "case friendly" updated version that is getting good reviews. I've got one on its way.
Phredeee said:
I put on a IQ shield matte. I like the matte finish but it is not for everyone. There is some lost clarity but much less glare and no fingerprints. I like the wet install for no bubbles and being easy. It takes some time to let the edges dry so they will stick. Let it sit at least overnight before using or putting on a case.
My case (Spigen Ultra Hybrid)did cause the corners to lift, a common problem with cases. IQ Shield has since come out with a "case friendly" updated version that is getting good reviews. I've got one on its way.
Click to expand...
Click to collapse
I ended up buying the skinomi matte screen protector which stuck on the edges perfect. Went without a case for a week and then put the spigen neo hybrid on which is my favorite case of all time and it peeled the corners still. I warmed the screen protector and was able to reform the corners a bit and it helped but i still want a problem free combination
This is the case and glass screen protector that I use. The setup is perfect for me. You could use any screen protector with this case. It also holds the glass ones down and keep them in place.
https://www.amazon.com/dp/B01INYYYDI/ref=cm_sw_r_other_apa_CE9Zxb7RJCJPC
https://www.amazon.com/dp/B01JTYPSLI/ref=cm_sw_r_other_apa_hB9ZxbR2MKR17
duracool said:
This is the case and glass screen protector that I use. The setup is perfect for me. You could use any screen protector with this case. It also holds the glass ones down and keep them in place.
https://www.amazon.com/dp/B01INYYYDI/ref=cm_sw_r_other_apa_CE9Zxb7RJCJPC
https://www.amazon.com/dp/B01JTYPSLI/ref=cm_sw_r_other_apa_hB9ZxbR2MKR17
Click to expand...
Click to collapse
Without clicking the link I'm gonna guess that's the unicorn beetle case. I have that myself and love it. I use the holster while at work
Great case. It works well with a glass screen protector.
I have an armorsuit on this phone, as well as several tablets and phones prior. Was originally skeptical of the curved edge, but it is working great so far. In the past 6 years armorsuits and common sense have kept me from having any cracked screens. And when I upgrade and sell the old phones, removing the armorsuit has always left a perfect as-new screen (but the housings usually have suffered damage from drops, etc.).
Skinomi
duracool said:
This is the case and glass screen protector that I use. The setup is perfect for me. You could use any screen protector with this case. It also holds the glass ones down and keep them in place.
https://www.amazon.com/dp/B01INYYYDI/ref=cm_sw_r_other_apa_CE9Zxb7RJCJPC
https://www.amazon.com/dp/B01JTYPSLI/ref=cm_sw_r_other_apa_hB9ZxbR2MKR17
Click to expand...
Click to collapse
Is your tempered glass screen protector any good? How is the clarity? Sensitivity?
The clarity and sensitivity is great. I have one on my phone and my fiances phone. This is the third one we bought and its pretty close to the flat ones. Just line it up because the cut outs are exact. No room for error.
So the question is probably familiar from past phones from Sammy such as Note8 or S8/s8+ lol... The consensus from previous reads on XDA and reddit seems to be Whitestone Dome but a lot also gave negative reviews of it due it either lose touch response, or peeling off too easy. I had purchased a full adhesive from aliexpress for my Note8 but could not really use it since I sold the phone to get the S9+ . Anyone has any good recommendation for a tempered glass based on the brands they got for their previous Sammy? I mean recommendation as in, they dropped the phone with it on, like on the corners and the screen survived even though the glass shattered? Case would be great too, as I have a Supcase on the way. Thanks!!
Not the Whitestone then? I was almost about to pull the trigger on getting one for the S9+ but I'm hesitant now.
I've been using Whitestone for myself and my kids, although it has it's fragilities (cold, an snow can alter it) its the best i've tried. I've already ordered mine for the S9+... If i were you get a couple... just in case. As once you've tested it, you won't go back on the side glued ones. You just need to glue it well, and don't be in a hurry.
I've never had issues with touch sensitivity or peeling off (that's even nuts as it's literally glued to the screen, if you break the dome and need to peel it off you should be careful as it's glued it shatters and pieces can jump).
There may be another option now and as upset as I was with the first interation of Zagg's tempered glass screen protector for the s8+, they have come out with the glass curve elite. https://www.zagg.com/us/en_us/invisibleshield/glass-curve-elite-samsung-galaxy-s9-plus/ They say that it has full adhesion. So if it actually works well they supply a lifetime warranty. It is 49.99 so it's expensive but I'm going to give it a shot.
Whitestone was great but with a long installation process, I went for it twice, I'm going to (no offense) pass on Whitestone for my s9+. If there was a tempered glass product for curved screens that was as easy to install as a flat screen tempered glass screen protector, and like a conventional screen protector has good full glass adhesion I'm going to go for that option.
I have tried almost 5 brands but still did not get satisfactory result.
Just pre ordered the white stone. It was the best on the note 8.
Upgrading from two S7 edge to two S9+ (already pre-ordered) I never tried tempered glass on my smartphones because I found them a little too expensive to justify given that I have to buy two glass protectors. The OTAO 3D glass protector looked to be an "inexpensive" way to give tempered glass a try, but someone on the S9 thread about Screen Protectors complained about the OTAO falling off his phone whenever he took it out of his pocket. Some folks have also mentioned that this protector doesn't fully cover the curve edge which makes it "case friendly", but this also make it less appealing. These two negative findings put some doubt in my mind about ordering this specific protector for now. Folks using the S8+ have given this protector a "good" review on Amazon. But I also don't know if most of these reviews are for the "old" version or for the "Updated" version on this protector for the S8+. If there's someone here that has used the "Updated" OTAO protector on a Galaxy phone with a curved screen (preferably the S8+)... can you tell us about your experience? I guessthe "Updated" version is the one being used for the S9+.
I have used Zagg's Invisible HD shields on all my smartphones. I found them to be durable and compatible with many cases. Including cases for the S7 edge.Installing them is a little complex and you need to get it right the first time in order to avoid bubbles and the edges from lifting. I had to return the one that I installed on my wife's S7 edge once because a corner kept lifting and getting dust under it. All I had to do was return the old one and they send me a new one. Once I installed the replacement correctly, it has stayed on her phone for over a year without any issues. I'm waiting for it to be available in Amazon as they're usually discounted. The Zagg website indicates that they're sold out of their Invisible HD shield for the S9+
tamanaco said:
Upgrading from two S7 edge to two S9+ (already pre-ordered) I never tried tempered glass on my smartphones because I found them a little too expensive to justify given that I have to buy two glass protectors. The OTAO 3D glass protector looked to be an "inexpensive" way to give tempered glass a try, but someone on the S9 thread about Screen Protectors complained about the OTAO falling off his phone whenever he took it out of his pocket. Some folks have also mentioned that this protector doesn't fully cover the curve edge which makes it "case friendly", but this also make it less appealing. These two negative findings put some doubt in my mind about ordering this specific protector for now. Folks using the S8+ have given this protector a "good" review on Amazon. But I also don't know if most of these reviews are for the "old" version or for the "Updated" version on this protector for the S8+. If there's someone here that has used the "Updated" OTAO protector on a Galaxy phone with a curved screen (preferably the S8+)... can you tell us about your experience? I guessthe "Updated" version is the one being used for the S9+.
Click to expand...
Click to collapse
OTAO have two versions, a case-friendly one, which has to leave a couple of areas exposed for the case to fit, and a full cover one. I have had the case friendly one on my S8 and been very pleased with it. Never popped off. One person complaining his came off should not be taken to be evidence that there is something inherently wrong. There could be two reasons - either his was slightly faulty with not enough glue - no company has 100% quality control - or maybe he didn't press it on hard enough when he fitted it.
I've had two. The first one cracked when I dropped the phone on a marble floor but the phone screen was unmarked. Even though it cracked, it did not pop off. The edges still stuck. The second one is still on the phone.
Peanuttree said:
There may be another option now and as upset as I was with the first interation of Zagg's tempered glass screen protector for the s8+, they have come out with the glass curve elite. https://www.zagg.com/us/en_us/invisibleshield/glass-curve-elite-samsung-galaxy-s9-plus/ They say that it has full adhesion. So if it actually works well they supply a lifetime warranty. It is 49.99 so it's expensive but I'm going to give it a shot.
Whitestone was great but with a long installation process, I went for it twice, I'm going to (no offense) pass on Whitestone for my s9+. If there was a tempered glass product for curved screens that was as easy to install as a flat screen tempered glass screen protector, and like a conventional screen protector has good full glass adhesion I'm going to go for that option.
Click to expand...
Click to collapse
Will be interested to hear how this full adhesive version stacks up against the LOCA types.
Sent from my SM-G935F using Tapatalk
n-j-f said:
OTAO have two versions, a case-friendly one, which has to leave a couple of areas exposed for the case to fit, and a full cover one. I have had the case friendly one on my S8 and been very pleased with it. Never popped off. One person complaining his came off should not be taken to be evidence that there is something inherently wrong. There could be two reasons - either his was slightly faulty with not enough glue - no company has 100% quality control - or maybe he didn't press it on hard enough when he fitted it.
I've had two. The first one cracked when I dropped the phone on a marble floor but the phone screen was unmarked. Even though it cracked, it did not pop off. The edges still stuck. The second one is still on the phone.
Click to expand...
Click to collapse
Thanks for your reply... The complains put "some doubt" in my mind about the protector, I had not concluded that there was something inherently wrong with the OTAO. I posted here because I wanted to hear comments from other folks before I made my decision.
I didn't know that OTAO also made a protector that fully covers the screen, but after you mentioned it... I searched further and also found the OTAO Full Screen Coverage - Double Strong 3D in Amazon. At the same $12 price as the Case Friendly. At this price point, I might get one of each and test them with the case I'm going to use. I'm looking for a slim TPU cases from Spigen, EasyAcc, ESR and Caseologic. Currently, I use a Ringke Slim case with my S7 edge, but given the larger screen size of the S9+; I'd like a more protective setup. What case are you using on your S8 with the OTAO case friendly protector?... Thanks again.
xterminater07 said:
So the question is probably familiar from past phones from Sammy such as Note8 or S8/s8+ lol... The consensus from previous reads on XDA and reddit seems to be Whitestone Dome but a lot also gave negative reviews of it due it either lose touch response, or peeling off too easy. I had purchased a full adhesive from aliexpress for my Note8 but could not really use it since I sold the phone to get the S9+ . Anyone has any good recommendation for a tempered glass based on the brands they got for their previous Sammy? I mean recommendation as in, they dropped the phone with it on, like on the corners and the screen survived even though the glass shattered? Case would be great too, as I have a Supcase on the way. Thanks!!
Click to expand...
Click to collapse
For my gs8+, I've had good experiences with both the Otao TGSP and the newer full-adhesive ones.
Until a full-adhesive TGSP comes out for the gs9+ from a company I recognize, I'm gonna start with the Otao gs9+ TGSP.
Sent from my SM-N910C using Tapatalk
optimummind said:
For my gs8+, I've had good experiences with both the Otao TGSP and the newer full-adhesive ones.
Until a full-adhesive TGSP comes out for the gs9+ from a company I recognize, I'm gonna start with the Otao gs9+ TGSP.
Click to expand...
Click to collapse
https://www.zagg.com/us/en_us/invis...protector/glass-curve-elite-samsung-galaxy-s9
optimummind said:
For my gs8+, I've had good experiences with both the Otao TGSP and the newer full-adhesive ones.
Until a full-adhesive TGSP comes out for the gs9+ from a company I recognize, I'm gonna start with the Otao gs9+ TGSP.
Sent from my SM-N910C using Tapatalk
Click to expand...
Click to collapse
How's the adhesive on the OTAO full adhesive for the s8+ that u got?
xterminater07 said:
How's the adhesive on the OTAO full adhesive for the s8+ that u got?
Click to expand...
Click to collapse
I'm using this one:
EyeO2 Screen Protector for Samsung Galaxy S8 Plus 9H Full Adhesive 3D Curved Tempered Glass Guard High Sensitivity HD Full Cover Edge Protector S8+ Protective Film Replacement Accessories Black 2 Pack https://www.amazon.com/dp/B074QN6ZB5/ref=cm_sw_r_cp_apa_jPHNAbDN9V2VR
And it's good.
Sent from my SM-N910C using Tapatalk
Well I've gambled on the zagg + defender combo, I hope they play nice.....
Will report back......
i've just ordered this can anyone recommend a decent case please.
https://www.amazon.co.uk/Protector-...=merchant-items&ie=UTF8&qid=1520177568&sr=1-3
I just ordered the Zagg. Saved £4 using promo code zagg10 at checkout. £36 felt easier to swallow then £40!
Sent from my SM-G935F using Tapatalk
n-j-f said:
OTAO have two versions, a case-friendly one, which has to leave a couple of areas exposed for the case to fit, and a full cover one. I have had the case friendly one on my S8 and been very pleased with it. Never popped off. One person complaining his came off should not be taken to be evidence that there is something inherently wrong. There could be two reasons - either his was slightly faulty with not enough glue - no company has 100% quality control - or maybe he didn't press it on hard enough when he fitted it.
I've had two. The first one cracked when I dropped the phone on a marble floor but the phone screen was unmarked. Even though it cracked, it did not pop off. The edges still stuck. The second one is still on the phone.
Click to expand...
Click to collapse
I also have an OTAO on my Note 8 - fits beautifully - holds very well - smooth - full responsiveness - no issues at all.
Geekser said:
I also have an OTAO on my Note 8 - fits beautifully - holds very well - smooth - full responsiveness - no issues at all.
Click to expand...
Click to collapse
What version of the OTAO are you using on your Note 8 [Case Friendly] or [Full Screen Coverage]? Are you using the "Updated" version that I believe has "full-adhesive"? Are you also using a case and if so... which one?
xterminater07 said:
So the question is probably familiar from past phones from Sammy such as Note8 or S8/s8+ lol... The consensus from previous reads on XDA and reddit seems to be Whitestone Dome but a lot also gave negative reviews of it due it either lose touch response, or peeling off too easy. I had purchased a full adhesive from aliexpress for my Note8 but could not really use it since I sold the phone to get the S9+ . Anyone has any good recommendation for a tempered glass based on the brands they got for their previous Sammy? I mean recommendation as in, they dropped the phone with it on, like on the corners and the screen survived even though the glass shattered? Case would be great too, as I have a Supcase on the way. Thanks!!
Click to expand...
Click to collapse
I'll be working on a buyers guide today and tomorrow it will be on my channel.. In the mean time I posted a thread about a 10 dollar dome glass copy from the supplying factory and their are a few full adhesive glass protectors I'm tested.. All the others are the same generic ones just like the S8/N8
I'm just jumping from the Moto x4 to S9 Plus
My protector option is one from the ************. I really love to have my S9Plus away from the scratches. As I'm having previous experience with the ************so I'm suggesting to get one from them.
They started shipping but I didn't got mine. Have you bought one from them and received it??
I bought the one from BigBen. Fit perfectly. No problem after 1 week. Just improve screen sensitivity.
I just installed the Whitestone Dome Glass on my S9+. Very easy to install and looks great so far. It doesn't seem to be compatible with the Spigen case I bought though, particularly the lower portion, I'm going to let the glue cure a bit longer and try it again.
UPDATE: I had the dome glass installed just a bit too low on the screen. I removed the glass and adhesive, then reinstalled and made sure the dome glass was correctly centered on the screen. Works great with the case now. Highly recommend this.
Bodyguardz is a more expensive option, but lifetime warrenty. I want to say it's about 10 bucks shipping for the warrenty replacements. I got mine at AT&T when I got my s9 plus yesterday. They installed it for me but it comes with a guide thingy like the Whitestone one.
Hunkman said:
They started shipping but I didn't got mine. Have you bought one from them and received it??
Click to expand...
Click to collapse
Yes, I bought one and even I got the screen protector.
todd3835 said:
Bodyguardz is a more expensive option, but lifetime warrenty. I want to say it's about 10 bucks shipping for the warrenty replacements. I got mine at AT&T when I got my s9 plus yesterday. They installed it for me but it comes with a guide thingy like the Whitestone one.
Click to expand...
Click to collapse
Is that a TGP or Full body screen protector??
xavdep said:
Is that a TGP or Full body screen protector??
Click to expand...
Click to collapse
It's a glass screen protector. Case friendly.
Tried the bodyguards pure arc. Complete garbage. Horrible sensitivity and it's a fingerprint magnet
Sent from my SM-G965U1 using Tapatalk
I just received my spigen 360 thin fit today and this is a pretty good screen protector especially when paired with the case. The touch response is good and I don't feel the need tho enable the setting for screen protector under advanced options.
Sent from my SM-G965U1 using Tapatalk
crzycrkr said:
Tried the bodyguards pure arc. Complete garbage. Horrible sensitivity and it's a fingerprint magnet
Sent from my SM-G965U1 using Tapatalk
Click to expand...
Click to collapse
I bought one too, and concur. Fingerprint magnet, and ruins sensitivity. You have to turn on increase sensitivity in the advanced settings, and still it's a bit wonky.
bkeaver said:
I just received my spigen 360 thin fit today and this is a pretty good screen protector especially when paired with the case. The touch response is good and I don't feel the need tho enable the setting for screen protector under advanced options.
Sent from my SM-G965U1 using Tapatalk
Click to expand...
Click to collapse
I got the Spigen neo flex today and had no issues installing on both of our phones. Seems to fit very well and touch response hasn't changed.
Sent from my SM-G965U using Tapatalk
the verizon branded Tempered flass one is full adhesive. ive been pretty pleased. bumped up sensitivity on phone and no issues at all.
OMYFILM Samsung Galaxy S9 Plus Tempered Glass Screen Protector [Bubble Free] [Case Compatible] 9H Hardness Screen Protector for Samsung S9 Plus (S9 Plus, Black)
https://www.amazon.com/Galaxy-S9-Pl...rotector+for+Samsung+S9+Plus+(S9+Plus,+Black)
Amazon.com link above. $9.00
Got this on Amazon.ca for under $15 CAD, it's curved, applied with zero bubbles and it works really good after raising the screen sensitivity.
Just installed the whitestone dome, I simply couldn't be more impressed. Make sure you watch the installation video a couple of times before applying… but it is hands down the only protector i will be buying from now on for all of my devices.
http://www.amazon.com/Dome-Glass-Protector-Dispersion-Whitestone/dp/B079YF5VS7
Otao case friendly
I got the Otao case friendly version for the S9 Plus from Amazon.com (ASIN: B07BSFLLKY). Rather than give a separate review here, this is what I have added as my review on Amazon. I hope this is allowed.
I had the Otao on my S8 and was very happy with it. On one occasion I dropped my phone. The screen protector cracked, which is what you would expect from a glass screen protector, but it saved the screen of my phone.
I was a bit wary when I read the first reviews of the S9 Plus version (which had a different ASIN number) but then I heard they were updating it. They reached out to me to offer me to try the new one (free of charge) which I just received. The main complaint about the previous version was not enough glue on the edges (it is edge only sticking) but the new version apparently has more glue and it certainly has stuck well on my S9 Plus. Obviously, the proof of the pudding will be it it still sticks well after it has been on a while and I will update my review if it develops a problem.
The installation tray makes it very easy to instal.
I am using it with a Spigen Neo Hybrid case and they fit together very well.
As I said, I did not have to pay for the protector but this review is my honest opinion and, if I did not like it, I would have said so.
Just to add - the packaging recommends turning on the touch sensitivity setting in Settings but so far I haven't found that necessary.
Try this: https://www.amazon.com/Protector【Case-Friendly】Full-Coverage-Tempered-Anti-Scratch/dp/B07B2Y6F9D
dpalmer76 said:
Try this: https://www.amazon.com/Protector【Case-Friendly】Full-Coverage-Tempered-Anti-Scratch/dp/B07B2Y6F9D
Click to expand...
Click to collapse
Does the glue cover entire surface of the screen or only the edges?
I’m looking for one that covers the entire screen most I’ve seen only covers partial off the top and bottom so it still looks like there’s a screen protector. I need fill coverage from top to bottom.
Another vote for the whitestone dome!
I've tried several tempered glass screen protectors since the S6+, and they all suck because the adhesive has trouble sticking to the edges so the sensitivity is terrible. The dome is the first I've used that I'm legitimately happy with.
The installation process is really intimidating at first because the process is different from your typical screen protector. But once you do it once and get the technique down, it's actually pretty fool-proof. The tray basically ensures that the alignment is perfect and adheres well. I happened to screw up the first time because my table wasn't fully level and the adhesive didn't disperse evenly and I got a tiny bubble...so don't take that little detail for granted. Luckily they give you two bottles of adhesive, and when I moved to a level counter and put it on a second time the adhesive spread perfectly on its own and it was really easy.
I've purchased (but not used yet) the Whitestone Dome screen protector. I've seen videos of both that and also the amFilm being installed. The only difference I saw was the Whitestone had a "bridge" for holding the adhesive bottle while it empties, while the amFilm offers a fingerprint-size cylindrical weight to place over the fingerprint area to reduce the amount of adhesive between the fingerprint sensor and the screen protector.
I see other brands for curing the adhesive with ultraviolet light have suddenly popped up as well.
Thoughts on which is the best?
Sent from my SM-N976V using Tapatalk
My wife has the Whitestone on her note 10+. The fingerprint works fine for her. When I program in my fingerprint it doesn't work well at all. Usually takes 2+ times to unlock it... So I guess it depends on an individuals fingerprint on how well it works... That being said, my wife has already put a hairline crack in the Whitestone. She did the same thing with several Whitestones on her note 8. I have had a Whitestone on my pixel 2xl since it came out and haven't cracked one, while she has cracked 4. My theory is that the adhesive creates a slightly spongy layer under the glass. When the glass is pressed on (like leaning over while in ones tight pockets) , the glass can crack. My wife is an er doctor and is constantly leaning over patients putting pressure on the phone. She always turns the phone towards her leg, so it's not the impact but rather the pressure. My pockets are generally looser and I rarely sit with my phone in my pocket. I assume that is why in almost 2 years I haven't cracked one.
Think they are both similar. ymmv on the fp sensor.
i'd say go with the amfilm because its cheaper and comes with 2.
I love my Whitestone Dome on my Note 10+, but I have to admit, if I had known about the AmFilm, I might've gone that direction instead. 2 for $40 is tempting and the also offer a lifetime warranty on replacements. Just pay S&H. Whitestone charges $9.99 S&H for warranty replacements. I assume AmFilm is similar in cost.
Here's my suggestion, if you can afford to eat the $40. Keep the Whitestone and order the AmFilm.
Install the AmFilm and use it for a week. Test sensitivity, durability, scratch resistance, and most importantly, the FP sensor.
Then after a week, rip it off, and install Whitestone Dome. Run the same test. If you prefer Whitestone, leave it on. If you prefer AmFilm, you still have a spare in the box, so rip off the Whitestone and reinstall AmFilm.
Then post on here your thoughts and feelings and why you chose one over the other.
Mr. Orange 645 said:
I love my Whitestone Dome on my Note 10+, but I have to admit, if I had known about the AmFilm, I might've gone that direction instead. 2 for $40 is tempting and the also offer a lifetime warranty on replacements. Just pay S&H. Whitestone charges $9.99 S&H for warranty replacements. I assume AmFilm is similar in cost.
Here's my suggestion, if you can afford to eat the $40. Keep the Whitestone and order the AmFilm.
Install the AmFilm and use it for a week. Test sensitivity, durability, scratch resistance, and most importantly, the FP sensor.
Then after a week, rip it off, and install Whitestone Dome. Run the same test. If you prefer Whitestone, leave it on. If you prefer AmFilm, you still have a spare in the box, so rip off the Whitestone and reinstall AmFilm.
Then post on here your thoughts and feelings and why you chose one over the other.
Click to expand...
Click to collapse
Thanks for the input. My situation's a little unique. I went all out when buying this phone with a 512GB 5G Version and a 512GB card installed. I have not used a screen protector in years and my phones are always flawless - my Note 8 that I just turned in for the Note 10 looks like it's brand new still. I work in an office and I keep the phone in my front right pants pocket with nothing else ever in that same pocket. I guess I just got the Whitestone dome because I went a little nuts with this phone and I expect it to last more than two versions (I usually slip versions) - maybe the Note 13 if there is going to be such an animal - even so maybe an excuse for wasting my money. Maybe I'll even return it. Long story short the screen protector already on the phone is fine for now for me and if it ever does start to wear, I'll peel it off and then debate longer about whether or not to use the Whitestone. So in my case actually probably a waste of money. The screen protector that comes on the phone actually goes all the way around the camera hole while the Whitestone has a notch on top of it which I don't really like. Call me nuts but that's my situation lol...
Sent from my SM-N976V using Tapatalk
KruseLudsMobile said:
Thanks for the input. My situation's a little unique. I went all out when buying this phone with a 512GB 5G Version and a 512GB card installed. I have not used a screen protector in years and my phones are always flawless - my Note 8 that I just turned in for the Note 10 looks like it's brand new still. I work in an office and I keep the phone in my front right pocket with nothing else ever in that same pocket. I guess I just got the Whitestone domebecause I went a little nuts with this phone and I expect the last more than two versions maybe the note 13 if there is going to be such an animal. Long story short the screen protector already on the phone is fine for now for me and if it ever does start to wear Auto spill it off and then debate longer about whether or not to use the white stone. So in my case actually probably a waste of money. The screen protector that comes on the phone actually goes all the way around the camera hole while the Whitestone has a notch on top for it which I don't really like. Call me nuts but that's my situation lol...
Sent from my SM-N976V using Tapatalk
Click to expand...
Click to collapse
Completely understand and agree. The factory installed screen protector is much better than people give it credit for. My wife used it on her S10+ until she finally scratched it up at the beach. Sandy fingers and all that. I replaced hers with the Ringke Dual Easy Film which she loves and I've used in the past. By the way, even though the sand scratched the funk out of her factory screen protector, the glass underneath was perfect.
And I also agree about the notch. It's my only complaint about the tempered glass screen protectors. Ringke Dual Easy Film actually covers the camera, but doesn't affect picture quality. So it's really invisible.
I had use Whitestone Dome Glass for Galaxy Note9 and my current phone, Note10. I didn't have any issue so far and fingerprint works great! and they also provides lifetime warranty for every time that you request.
CBMC said:
My wife has the Whitestone on her note 10+. The fingerprint works fine for her. When I program in my fingerprint it doesn't work well at all. Usually takes 2+ times to unlock it... So I guess it depends on an individuals fingerprint on how well it works... That being said, my wife has already put a hairline crack in the Whitestone. She did the same thing with several Whitestones on her note 8. I have had a Whitestone on my pixel 2xl since it came out and haven't cracked one, while she has cracked 4. My theory is that the adhesive creates a slightly spongy layer under the glass. When the glass is pressed on (like leaning over while in ones tight pockets) , the glass can crack. My wife is an er doctor and is constantly leaning over patients putting pressure on the phone. She always turns the phone towards her leg, so it's not the impact but rather the pressure. My pockets are generally looser and I rarely sit with my phone in my pocket. I assume that is why in almost 2 years I haven't cracked one.
Click to expand...
Click to collapse
Ok maybe your wife should not be an ER doctor if she is breaking her whitestone crushing it against patients?
I will say that my wife has cracked all of her whitestone protectors, while I only just cracked the one on my Note 9 after almost a year of being break free. I am a contractor who is constantly in situations where phones get hit or impacted (I do use an Otterbox defender case while at work), she works in an office and yet still seems to be breaking her tempered protectors. often Which is exactly why I put a tempered (whitestone) protector on her phone, because otherwise it would be her display that was getting broken, and since I pay for her and my phones on my VZ account.... I need these expensive phones protected as much as possible.
KruseLudsMobile said:
I've purchased (but not used yet) the Whitestone Dome screen protector. I've seen videos of both that and also the amFilm being installed. The only difference I saw was the Whitestone had a "bridge" for holding the adhesive bottle while it empties, while the amFilm offers a fingerprint-size cylindrical weight to place over the fingerprint area to reduce the amount of adhesive between the fingerprint sensor and the screen protector.
I see other brands for curing the adhesive with ultraviolet light have suddenly popped up as well.
Thoughts on which is the best?
Sent from my SM-N976V using Tapatalk
Click to expand...
Click to collapse
I love Whitestone Dome and have used them for a long time. My brother just got the Note 10+ and his works great. I have the S10+ and it has been fine for me. I broke mine when I dropped it getting out of my car, but luckily it was just the dome glass and not my screen. The warranty fee of $9.99 is annoying, but it is better than buying a new one. I don't know anything about AM Film, but Whitestone has been around for a long time and I think we are seeing a lot of knock-offs start to come out. I would say use Whitestone because the quality is probably better.
If you shop there website, they usually have some good discounts available. My brother got his for 20% off and when I bought mine it was 30% off.
I was looking into getting the two for my new Note 10 but I heard amFilm only gives one replacement per purchase compared to Whitestone which replaces as many times as you need to. So even if you break or mess up installing your replacement, you're going to have to buy a whole new kit at regular retail cost again.
Honestly, I'm leaning more towards the Whitestone one just because it's only a few bucks more and I've heard it's more reliable than amFilm. Plus the warranty stuff I mentioned lol.
I use whitestone dome. I have since the note 8. It's credible. AmFilm is not.
Do these type screen protectors leave behind any residue when you remove them?
754boy said:
Do these type screen protectors leave behind any residue when you remove them?
Click to expand...
Click to collapse
No they do not leave residue behind. When removed the residue goes stays with the screen protector. Still clean the screen but you won't have any residue behind.
I've had to remove mine and reinstall due to bubbles forming a week after but new one is doing good now.
I have the Whitestone Dome glass.
Sent from my SM-N975U1 using Tapatalk
754boy said:
Do these type screen protectors leave behind any residue when you remove them?
Click to expand...
Click to collapse
Depends, especially if you've had it on there for a while, it will leave residue. You'll have to slowly wipe it off with rubbing alcohol.
Hello, i read about squiggles or something, some weird things happening on edges of whitestone dome due to the glue on corners after ~1 or 2 months.
Many of these comments are found on Reddit, while in this topic everyone seems to say whitestone is very good and lasted long for them.
Examples :
https://i.imgur.com/PclyW3M.jpg
https://i.imgur.com/WWtsyZH.jpg
Who can i trust? At this price i am expecting a 'flawless' screen protector.
Also, anyone tried protection that are only available with professional installation in shops? Like this kind of stuff :
https://www.youtube.com/watch?v=jkul7RZkmFw
Amfilm has been excellent so far. so far
Sent from my SM-N975F using Tapatalk
KruseLudsMobile said:
I've purchased (but not used yet) the Whitestone Dome screen protector. I've seen videos of both that and also the amFilm being installed. The only difference I saw was the Whitestone had a "bridge" for holding the adhesive bottle while it empties, while the amFilm offers a fingerprint-size cylindrical weight to place over the fingerprint area to reduce the amount of adhesive between the fingerprint sensor and the screen protector.
I see other brands for curing the adhesive with ultraviolet light have suddenly popped up as well.
Thoughts on which is the best?
Click to expand...
Click to collapse
Some people have a brand loyalty to 'Whitestone', maybe because they haven't tried other UV solutions, but more likely because they've had a positive experience with it.
What you should be aware of is that 'Whitestone' didn't invent the process, however, fair dues to them in that they have refined the process in an effort to make it as easy, foolproof and of course marketable as possible.
If you're a relatively competent person, that doesn't require the peripheral accessories that 'Whitestone' and for that matter, 'Amfilm' provides there are much cheaper, and imho just as effective products out there.
Maybe the thing to do is buy one from 'Ebay', average prices are around £3 -£5, and even cheaper on 'Aliexpress'. See if it works for you, and once you've got the principle of it under your belt, maybe then try one of the more expensive brands if not satisfied with their quality, but in all honesty, they're all just glass and UV glue.
mafy31 said:
Hello, i read about squiggles or something, some weird things happening on edges of whitestone dome due to the glue on corners after ~1 or 2 months.
Many of these comments are found on Reddit, while in this topic everyone seems to say whitestone is very good and lasted long for them.
Examples :
https://i.imgur.com/PclyW3M.jpg
https://i.imgur.com/WWtsyZH.jpg
Who can i trust? At this price i am expecting a 'flawless' screen protector.
Also, anyone tried protection that are only available with professional installation in shops? Like this kind of stuff :
https://www.youtube.com/watch?v=jkul7RZkmFw
Click to expand...
Click to collapse
Every phone I have used whitestone on any phone they look like yours a few months in. Guess I will keep rocking factory samsung screen protector for now
oneandroidnut said:
Every phone I have used whitestone on any phone they look like yours a few months in. Guess I will keep rocking factory samsung screen protector for now
Click to expand...
Click to collapse
More reason to use the cheaper alternatives, since £3 every 3 months or so isn't such a huge hit, even cheaper than those TGSP with the glue on the edges.
Unfortunately the factory fitted screen protectors are only good for scratch resistance, best drop protection is still glass.
kxdaorbit said:
More reason to use the cheaper alternatives, since £3 every 3 months or so isn't such a huge hit, even cheaper than those TGSP with the glue on the edges.
Unfortunately the factory fitted screen protectors are only good for scratch resistance, best drop protection is still glass.
Click to expand...
Click to collapse
True but also the factory protector gets scratched easily. I use the S View cover and it is horrible, first day it got scratched on the side already and now i get scratches here and there despite being very careful.
It fits the Note so well, i wish i could find the same quality, gloss vibrant protector with no bubbles and that fits all the screen like the factory one.
I would like to try professionally installed protectors (self curing ones) but it seems that they are not really glossy on the videos i have seen.
Are there any recommended cases that do not interfere with the Whitestone tempered glass screen protector? I know some cases can cause screen protectors to peel up in the corners, since I spent the money on the Whitestone, I want to make sure I don't get a case that won't play nicely with it.
Any recommendations?
Thanks.
I've used the Spigen Neo Hybrid on my Note 8 and now my Note 10. Both have whitestone protectors on them.
https://www.amazon.com/Spigen-Hybrid-Designed-Samsung-Galaxy/dp/B07SXSMXVW
Thanks, I had been looking at some Spigen cases since I previously had one on an S7. Decent cases and not expensive either.
Romans8vs1 said:
I've used the Spigen Neo Hybrid on my Note 8 and now my Note 10. Both have whitestone protectors on them.
https://www.amazon.com/Spigen-Hybrid-Designed-Samsung-Galaxy/dp/B07SXSMXVW
Click to expand...
Click to collapse
Really? I have the neo hybrid on my n10+ and have been eyeing the whitestone. I may just pull the trigger if it works with my current case.
I'm using the flimsy spigen neo flex, dont get me wrong it's a spigen so it works but hate all the finger prints, can scratch easy. The best part of it tho is its case friendly.
ssgunner20 said:
Really? I have the neo hybrid on my n10+ and have been eyeing the whitestone. I may just pull the trigger if it works with my current case.
I'm using the flimsy spigen neo flex, dont get me wrong it's a spigen so it works but hate all the finger prints, can scratch easy. The best part of it tho is its case friendly.
Click to expand...
Click to collapse
It certainly does. It is a perfect fit in my opinion. There is very little space between the screen protector and the edge of the case.
Whitestone protector delivered today, and a complete fail at installation.
I should have known something was up as it was missing the little suction cup, but since I figured that was just needed to remove the guide it should not be a big deal. Watched half a dozen or so videos, felt pretty confident to get started. Took everything slowly, but when I went to move the liquid to the center it kept flowing to the bottom. Even after I laid the phone back flat on my desk, I tried tilting it in the opposite direction, but the fluid appeared to be just running out the bottom between the 2 pieces of the holder.
At that point took everything out and cleaned it off, tried again, this time the glue did not spread to the top of the phone (my desk may not be perfectly level, but it's also not way off either). With the screen protector dropped I tried to coax as much of the glue towards the top as I could. For some reason all the glue seemed to just want to run off the bottom of the phone and then end up between the 2 pieces of the holder/alignment thing. The phone was pushed all the way into it, with the glue initially dropped on the screen it stayed in place, but for some reason after that it just wanted to run off the bottom no matter what.
Ultimately, what I am left with is a bunch of small bubbles and an area around the camera that has no glue. I should have just grabbed a cheap protector and been done with it. Leaving the Whitestone on there for now, even with the bubbles and piece around the camera it is still better than nothing. But, I'm pretty frustrated with the whole thing.
Sorry to hear this, I have been thinking about getting one of thhese whitestone protectors, but then I encounter sad stories, and there are worse ones! I will stick to the tpu/pet/hidrogel ones
It's definitely frustrating as I carefully followed all the steps. The Whitestone does feel great though and the fingerprint reader is not affected at all. Just have the annoying piece by the camera where it didn't stick.
Also, can confirm it works perfectly with the Spigen case mentioned above.
Mostly all of them have worked fine for me so far. I'm eyeing the new Marcel Case by samsung as well .. hope that fits it too
Dang I hope it goes well for me, just ordered 2 yesterday with promo code $52
Sent from my SM-N975U using Tapatalk
Good luck, take your time and you will more than likely be fine. What stinks in my case is I can't fix the messed up piece.
naiku said:
Are there any recommended cases that do not interfere with the Whitestone tempered glass screen protector? I know some cases can cause screen protectors to peel up in the corners, since I spent the money on the Whitestone, I want to make sure I don't get a case that won't play nicely with it.
Any recommendations?
Thanks.
Click to expand...
Click to collapse
Hej...
I'm using Clear Ringke Fusion with Whitestone and there's no problem at all...no peeling on the corners... nothing...
Between case and glass is little space which allows to cooperate perfectly