Hi all,
I have a MTCD unit running original with a PX3 1GB.
In last years I already upgraded it to 2GB wich is running good.
A while ago I bought a PX5 board to upgrade but with the PX5 board I have issues playing video (IPTV, some Youtube/ Kodi movies/normal videos on USB etc). I hear the sound going on but video just freezes after some seconds.
I tried all the different roms malaysk, Hal9k etc etc but all the same problem. ALmost gets me thinking that it's a hardware accelaration issue or something.
When I switch back to PX3 all the video goes fine.
Is there some fix for it? I really play a lot of video in the car (also for the backscreens. in the headrests).
Did you try allowing the video while driving from options? For permanent allowance you can connect the BRK wire to some GND (ground). I had similar issue with youtube, video showed for a sec then turns white. I guess your case is the same, just does not repaint the video area and only freezes.
Related
Hello,
I got a very annoying problem with my pumpkin head unit. Theres a noise, like when you place a smartphone close to speaker, which I hear all the time coming out of my car speakers.
Sometimes it's quiet and sometimes I hear that noise.
Is there any way to fix that?
My HeadUnit is (Description from Pumpkin Website):
Pumpkin 7 Inch Quad Core Android 4.4 Car Stereo DVD Player for Opel Vauxhall 2 Din support DAB+ AV Output MirrorLink 3G WiFi OBD2 DVR Steering Wheel Control
I run Malaysk Rom, but had this issues even with the standard ROM.
Would be happy if anybody could help me.
Regards
Ben
bump
No ideas?
Any ideas
I would be happy if someone could help me with my Problem
It's likely noise from the screen. Try turning the screen off and see if it goes away. It won't be easy to fix. Make sure all your grounds are as good as possible and make sure they are as direct to the battery as you can get. Noise like this is from a bad circuit design. It's the difference between an expensive well-engineered board and some POS from China. Yeah, I got one too, the Lollipop unit (self-rooted w/Viper).
If you only get the noise when the car is running it could be noise from your alternator or plug wires. That's harder to fix. You could use one of the crazy capacitors they make for car audio, but if you aren't running a 1000W, they can be overkill. I would try 1000uF cap across the 12V battery supply to ground, as close to the head unit as you can get it. Make sure the cap is rated at least 15V or so (it will see more than 12 from a car!). It will be electrolytic, so make sure you obey polarity. I'll be doing this myself later today.
May be worth a try running a wire from the negative of the battery post to the radio ground...I would just do it quick and easy in the driveway before trying to route it through the car.
Thank you for your support on that...
Unfortunately that sounds not that easy. I thought this might be a common problem with those head units :-/
I have a sound coming thru the speakers as well kinda sounds like a hard drive reading data when its booting up but goes away once its booted & running.
Might try running a better ground see if that helps.
Hello all
I was wondering if anyone has this head unit, Joying 6.2 Inch Single Din Car Radio Android 8 Oreo 4GBRAM 1 Din Touch Screen Audio System, I just installed it. (sorry can't post link)
Many things seem to work ok, but when streaming from the audio player from my iphone 6s+ 11.3ios, it crackles predictably at various parts in a song. For instance, one song, which plays cleanly on my subaru stock hu, crackles crazily at exactly 15 seconds in. I actually suspected the audio file. Other audio files stop playing within a few seconds.
This is pretty disappointing, this is one of the main functions of this HU for me. I am looking into updates, but I bought an Oreo HU with the hopes the OS would have stable functions of at least the most used functions. Just wondering if anyone out there is experiencing this type of thing on 8.0 with the joying 4GB versions. Thanks
Did you ever get this sorted out I am looking at the same unit
edie209 said:
Did you ever get this sorted out I am looking at the same unit
Click to expand...
Click to collapse
I think so. It looks like the problem was playing media I did not have fully downloaded. So the player was making itunes download the media I own from itunes but didn’t have fully downloaded. While it was doing that, it was hitting bluetooth and wifi pretty hard and I heard cracking and stopping.
Streaming media that lives on the device worked fine. Spotify for some reason did not do this, so this was probably something to do with apple IMO. I am enjoying this head unit except for how light it is in full sun, its in an open top car.
thanks for letting me know. I have now ordered one.
Hello guys, I have a Xtrons MTCD px5 unit with android 8 on it, I was switching back to the old px3 cpu which I've previously had (the original one, because my px5 cpu is bought), wanted to install the px5 board back in, did it, put all bsck together, switched ignition of the car on, and the unit began to catch smoke, so something fried inside of it, switched back to the px5 board (installed it in the unit) and everything is working fine and normal except the fact that I don't have no sound at all anymore, everything sound related is dead... any solutions, maybe an external sound card if possible? I use the rca's because I have an amplifier in the back.
GA9350b No sound as well
Hey, I have changed my ECU on my E46 and my HU Eonon GA9350b also completely lost the sound. Everything works except the sound. I have updated the MCU, the software, I checked all the wiring and I even replaced it with my old Pioneer and the sound works on it. Does anyone have any idea what it might be?
Hi,
Does anyoen have nay experience with this head unit? I installed mine and I'm noticing its bit slow and has some hiccups, specifically in the audio (call audio is horrible but music sounds great) and reverse cam department (it lags and its slow to turn on)
MCU: G6-TS.210818(VHD-YT-9)
HMI: JYKJ.G6.D.Q.F.I.2021.11.04.09.00
zachariostevens said:
Hi,
Does anyoen have nay experience with this head unit? I installed mine and I'm noticing its bit slow and has some hiccups, specifically in the audio (call audio is horrible but music sounds great) and reverse cam department (it lags and its slow to turn on)
MCU: G6-TS.210818(VHD-YT-9)
HMI: JYKJ.G6.D.Q.F.I.2021.11.04.09.00
Click to expand...
Click to collapse
May be you find some guys with the same MCU in this thread: https://forum.xda-developers.com/t/...er-8667q-based-devices.4426823/#post-86789865
Otherwise... I fear this is not a unit where you can find a lot in the moment.
Hi Guys,
A while back, I purchased the T10 unit from Srnubi. It worked perfectly for day 1. All speakers working, subwoofer was loud, everything was great. I came back to the car the next day and there was 0 subwoofer! Nothing was changed, everything normal so I started trouble shooting and I testing turning the bass up on the DSP to max, only then I could very faintly hear the Sub working. I figured I would try to reset the unit in hopes that it would work but now I have a factory android head unit with no running software (except the android auto and carplay software) and still next to no subwoofer output. This lead me to believe that the subwoofer out RCA is not working. I tested all RCA's and they're all very faint (I'm running the speakers from an amp which is connected to the head units speaker wire as the chanels). Has anyone had this issue before and is there a way I can fix the RCA Output without opening up the headunit and looking for faults on the board? And how do I install the firmware that Srnubi has sent through? They've completely stopped replying to me and didn't provide any instruction, worst part is they waited until my 15 days was over to stop replying and now I can't raise a dispute on AliExpress.
Any help would be much appreciated!
Cheers!
rorschach_96 said:
Hi Guys,
A while back, I purchased the T10 unit from Srnubi. It worked perfectly for day 1. All speakers working, subwoofer was loud, everything was great. I came back to the car the next day and there was 0 subwoofer! Nothing was changed, everything normal so I started trouble shooting and I testing turning the bass up on the DSP to max, only then I could very faintly hear the Sub working. I figured I would try to reset the unit in hopes that it would work but now I have a factory android head unit with no running software (except the android auto and carplay software) and still next to no subwoofer output. This lead me to believe that the subwoofer out RCA is not working. I tested all RCA's and they're all very faint (I'm running the speakers from an amp which is connected to the head units speaker wire as the chanels). Has anyone had this issue before and is there a way I can fix the RCA Output without opening up the headunit and looking for faults on the board? And how do I install the firmware that Srnubi has sent through? They've completely stopped replying to me and didn't provide any instruction, worst part is they waited until my 15 days was over to stop replying and now I can't raise a dispute on AliExpress.
Any help would be much appreciated!
Cheers!
Click to expand...
Click to collapse
DSP output to subwoofer has probably burned (regulator voltage chip inside on board), must be replaced.