Hey guys, I have the 910v I tried to manually update with Odin to 5.1.1. This isnt rooted or unlocked. Odin failed with the following error on my phone:
SW REV CHECK FAIL : [tz]Fused 2 > Binary 1
I have tried the VZW Software repair with no luck, as well as PIT file. Please help me get this thing working again! It just boots to a screen saying Software update failed and to run repair software on computer.
greg_gorrell said:
Hey guys, I have the 910v I tried to manually update with Odin to 5.1.1. This isnt rooted or unlocked. Odin failed with the following error on my phone:
SW REV CHECK FAIL : [tz]Fused 2 > Binary 1
I have tried the VZW Software repair with no luck, as well as PIT file. Please help me get this thing working again! It just boots to a screen saying Software update failed and to run repair software on computer.
Click to expand...
Click to collapse
http://forum.xda-developers.com/note-4-verizon/general/debrick-procedure-t3370661
Thanks for the reply. I wish I would have saw that earlier. I ended up fixing it by re-flashing the PIT file.
When rooting my S7, it got stuck in a bootloop. When I attempted to flash back to the factory firmware, ODIN failed, and now my phone is totally bricked. I can enter download mode, but not recovery mode. When attempting to flash the latest update firmware (04/19), it continues to fail with a "SW REV CHECK FAIL: [system]Fused 3 > Binary 1" error code, which I've found is supposed to mean that I'm downgrading firmware, but it's simply not the case. I've checked my drivers, tried different versions of ODIN, etc. but nothing works.
Any ideas?
maelstromm15 said:
When rooting my S7, it got stuck in a bootloop. When I attempted to flash back to the factory firmware, ODIN failed, and now my phone is totally bricked. I can enter download mode, but not recovery mode. When attempting to flash the latest update firmware (04/19), it continues to fail with a "SW REV CHECK FAIL: [system]Fused 3 > Binary 1" error code, which I've found is supposed to mean that I'm downgrading firmware, but it's simply not the case. I've checked my drivers, tried different versions of ODIN, etc. but nothing works.
Any ideas?
Click to expand...
Click to collapse
Try a couple different firmwares, for me it hasn't always worked on my first try. You could also try the prince comsey Odin instead that may or may not help depending on which firmware you are flashing.
maelstromm15 said:
When rooting my S7, it got stuck in a bootloop. When I attempted to flash back to the factory firmware, ODIN failed, and now my phone is totally bricked. I can enter download mode, but not recovery mode. When attempting to flash the latest update firmware (04/19), it continues to fail with a "SW REV CHECK FAIL: [system]Fused 3 > Binary 1" error code, which I've found is supposed to mean that I'm downgrading firmware, but it's simply not the case. I've checked my drivers, tried different versions of ODIN, etc. but nothing works.
Any ideas?
Click to expand...
Click to collapse
Give bra1 build a try if you haven't. I upgraded too far with an AT&T firmware and had to Odin bra1 first on the U variant firmware, then could Odin bra1 V variant firmware. Here is the V variant you can try first: https://androidfilehost.com/?fid=962187416754456736
Also post your bootloader info. See if your phone still shows G930V or if it's switched to G930U variant and if it says build/baseband version post that too please. Both "too new of a bootloader" and mismatched models can be the cause of that
Edit: Here is another full version of the 4/19 firmware you mention: https://androidfilehost.com/?fid=818070582850509181
Repair Assistant will restore your phone https://www.verizonwireless.com/support/knowledge-base-80201/
DabbingDuke said:
Repair Assistant will restore your phone https://www.verizonwireless.com/support/knowledge-base-80201/
Click to expand...
Click to collapse
Sadly this can fail from even a 930U vs 930V variant difference. It's great when it works but not a great fallback if you have tried any other variant Odin/rom
djh816 said:
Give bra1 build a try if you haven't. I upgraded too far with an AT&T firmware and had to Odin bra1 first on the U variant firmware, then could Odin bra1 V variant firmware. Here is the V variant you can try first: https://androidfilehost.com/?fid=962187416754456736
Also post your bootloader info. See if your phone still shows G930V or if it's switched to G930U variant and if it says build/baseband version post that too please. Both "too new of a bootloader" and mismatched models can be the cause of that
Edit: Here is another full version of the 4/19 firmware you mention: https://androidfilehost.com/?fid=818070582850509181
Click to expand...
Click to collapse
Thanks for your help here!
I went back to BRA1 build but can't seem to change back to VZW
In download mode it says that it is a G930A
Code:
<ID:0/038> Odin engine v(ID:3.1207)..
<ID:0/038> File analysis..
<ID:0/038> skip file list for home binary
<ID:0/038> persist.img.ext4
<ID:0/038> Home Binary Download
<ID:0/038> SetupConnection..
<ID:0/038> Initialzation..
<ID:0/038> FAIL! SHA256 is invalid
<OSM> All threads completed. (succeed 0 / failed 1)
I seem to remember Odin being an issue for me too at some point, do you have Odin v3.12 PrinceComsy?
I do have his Odin. For some reason it comes up a Chinese error when trying to run it. Will redownload tomorrow again.
Do you have any specific firmware that should work? Doesn't necessarily need to be VZW as I'm traveling and will use a different GSM sim.
Thanks!
turnert said:
Try a couple different firmwares, for me it hasn't always worked on my first try. You could also try the prince comsey Odin instead that may or may not help depending on which firmware you are flashing.
Click to expand...
Click to collapse
PalmCentro said:
I do have his Odin. For some reason it comes up a Chinese error when trying to run it. Will redownload tomorrow again.
Do you have any specific firmware that should work? Doesn't necessarily need to be VZW as I'm traveling and will use a different GSM sim.
Thanks!
Click to expand...
Click to collapse
I tested out one of the Oreo AT&T builds and ended up having to revert. Here was my route:
1) odin SM-G930U_1_20170516105039_fspus9jwu3_fac.zip
2) download verizon wireless software upgrade tool, restore to U variant firmware it offers (in my case BRA1)
3) odin G930VVRS4BRA1_G930VVZW4BRA1_VZW
If that doesn't work, try other full odin builds recent/old. Good luck!
Edit: I assume you know this but all USA variants with locked bootloader are the same hardware so A, U, V variants should all "work" but then its up to which version of firmware, which bootloader you currently have, which model you current have shown in bootloader. I had the best luck switching the A variant back to U, then to V. When i tried to go directly from the A firmware back to V variant directly, odin failed and Verizon's tool was useless cause it wasn't a V variant model at the time.
Will Only Boot Into Download Mode
Currently running BlackPearl Rom Android 8.1.0
Won't let me re-install earlier 7.0.0 firmware
gives me Complete(Write) operation failed
Also I've got the "SW REV. CHECK FAIL. DEVICE: 2 , BINARY: 1" error
please help
Bricked my s8+ hope someone can help!
Model SM-G955F
I tried to root it couldn't get some stuff working I ended up going in dev options and turned OEM unlocking either on or off..Then tried to root... Ended up getting the FRP lock and tried to flash to basic rom again.
I'm currently trying to use Odin to install this rom:
DOWNLOAD SAMSUNG GALAXY S8+ SM-G955F EVR UNITED KINGDOM (EE) G955FXXS6DTA1 FIRMWARE on SAMMOBILE
If I try turn it on it says
An error has occured while updating the device software. Use the emergency recovery function in the smart switch pc software. I tried to use smart switch to fix it but they removed the section where you search for models and I used a old verison which said the device was not supported
If I try use odin whilst in download mode it gives the following error
SW REV. Check fail )bootloader) device: 7 Binary: 6 (I think it says SW REV my eyes are terrible and its hard to read lol)
I'm thinking about taking the loss and just selling it on ebay as broken unless someone can help.
Thanks guys
Tobbo88 said:
Bricked my s8+ hope someone can help!
Model SM-G955F
I tried to root it couldn't get some stuff working I ended up going in dev options and turned OEM unlocking either on or off..Then tried to root... Ended up getting the FRP lock and tried to flash to basic rom again.
I'm currently trying to use Odin to install this rom:
DOWNLOAD SAMSUNG GALAXY S8+ SM-G955F EVR UNITED KINGDOM (EE) G955FXXS6DTA1 FIRMWARE on SAMMOBILE
If I try turn it on it says
An error has occured while updating the device software. Use the emergency recovery function in the smart switch pc software. I tried to use smart switch to fix it but they removed the section where you search for models and I used a old verison which said the device was not supported
If I try use odin whilst in download mode it gives the following error
SW REV. Check fail )bootloader) device: 7 Binary: 6 (I think it says SW REV my eyes are terrible and its hard to read lol)
I'm thinking about taking the loss and just selling it on ebay as broken unless someone can help.
Thanks guys
Click to expand...
Click to collapse
You are trying to flash older firmware than what is on your phone. Device 7 = current bootloader version on phone.Binary 6 = bootloader your trying to flash.
When looking at firmware names the 5th number from the right is the bootloader version number of the firmware you are downloading.You will need version 7 bootloader firmware or higher to flash in Odin.
spawnlives said:
You are trying to flash older firmware than what is on your phone. Device 7 = current bootloader version on phone.Binary 6 = bootloader your trying to flash.
When looking at firmware names the 5th number from the right is the bootloader version number of the firmware you are downloading.You will need version 7 bootloader firmware or higher to flash in Odin.
Click to expand...
Click to collapse
The one I'm downloading says its the latest version tho
Tobbo88 said:
The one I'm downloading says its the latest version tho
Click to expand...
Click to collapse
I have checked and for EVR (EE) version 6 bootloader is the latest one out.
All I can suggest is wait for an update or flash BTU firmware which is on version 7 firmware.
For downloading latest firmware use PC app called frija or samfirm. Far quicker than downloading through sammobile.
Frija
https://forum.xda-developers.com/s10-plus/how-to/tool-frija-samsung-firmware-downloader-t3910594
Or samfirm
https://samfirm.en.lo4d.com/windows
spawnlives said:
I have checked and for EVR (EE) version 6 bootloader is the latest one out.
All I can suggest is wait for an update or flash BTU firmware which is on version 7 firmware.
For downloading latest firmware use PC app called frija or samfirm. Far quicker than downloading through sammobile.
Frija
https://forum.xda-developers.com/s10-plus/how-to/tool-frija-samsung-firmware-downloader-t3910594
Or samfirm
https://samfirm.en.lo4d.com/windows
Click to expand...
Click to collapse
Thanks loads for your help!
I've got the file manage to get around 90% of the bar done then it fails just after saying cache.img then I get red error on the screen which says Custom Binary(USERDATA) Blocked by FRP Lock
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<ID:0/003> cache.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any ideas?
Thanks again
i wanted to root my device so i flashed twrp for sm-g9350 and now my phone is stuck in boot loop. i tried installing a firmware from 2019 but it say
sw rev check fail: [aboot] fused 5> binary 4 . i only have a non premium account on sammobile so i cant download the latest firmware.​https://www.sammobile.com/samsung/g...e/SM-G9350/CHC/download/G9350ZCS5CTA1/313222/ can anyone help me with this