Need Help - New Xtrons Radio doesnt Start - Android Head-Units

Hey Guys,
just Recived an Xtrons Head Unit for the Fiat Grande Punto. So yesterday we tryed to install it but what to say... it does not Start.
Maybe you guys know how to solve the problem?
btw. The Red (ACC) Wire is going to the can bus adapter and not to the iso plug, is that correct?
here you can see the photos: g o o . g l / 2 w j j v P
Thank you for helping.

nobody can help me to solve that problem?

Rajko2121 said:
Hey Guys,
just Recived an Xtrons Head Unit for the Fiat Grande Punto. So yesterday we tryed to install it but what to say... it does not Start.
Maybe you guys know how to solve the problem?
btw. The Red (ACC) Wire is going to the can bus adapter and not to the iso plug, is that correct?
here you can see the photos: g o o . g l / 2 w j j v P
Thank you for helping.
Click to expand...
Click to collapse
With a wire you need connect the ACC switched +12v power cable from at example the cigarette lighter to the related ACC +12v switched power on main HU harness connector.
On Fiat Grande Punto Mk199 switched +12v power is from vehicle canbus line.

So i need to connect an ne Cable from The Cigarette Lighter to the Red Cable which is going to the can bus Adapter and then connecting the new cable with the yellow 12v cable in the ISO socket, right?
EDIT: pls look at the new photo at the link in first post g o o . g l / 2 w j j v P

Rajko2121 said:
So i need to connect an ne Cable from The Cigarette Lighter to the Red Cable which is going to the can bus Adapter and then connecting the new cable with the yellow 12v cable in the ISO socket, right?
EDIT: pls look at the new photo at the link in first post g o o . g l / 2 w j j v P
Click to expand...
Click to collapse
you need connect to the related pin in main harness not on canbus box harness. Canbus boxes are usually powered from main HU harness

iRcKenny said:
you need connect to the related pin in main harness not on canbus box harness. Canbus boxes are usually powered from main HU harness
Click to expand...
Click to collapse
so just one wire from the lighter to the yellow 12V cable at iso plug?

Related

info on usb on uniway needed please

hi just purchased the uniway 9 inch 7.1.1 head unit but there is no manual with it ,can anyone tell me were the male usb cable goes thats coming out of back of unit in the wiring loom ,,,thank you
just an USB input... you dont need to hook it up to anything if not needed.
thanks
i have ordered the dab dongle ,it looks as if it has if its got a female usb input ,so would this usb from head plug into it ?

Unknown brand for Citroen C5 ( New Android 9 )

Hi XDA
We bought a new android head unit ( https://www.aliexpress.com/item/Bes...103320.html?spm=a2g0o.cart.0.0.4cbf3c006VNKDW) for our Citroen C5 2010 and it works great. Seems like the CANBUS support is way better now, than just 2-4 years ago in the old Android car radios. It detects when doors are open etc. Pretty cool .
I have a few question and maybe some of you might be able to answer.
1) The cable that supplies the USB connector ( on the picture ) also splits out into a grey cable. I was wondering if any of you have seen this cable before and know what it is for?
2) I'm still trying to figure out what brand of radio this is. Maybe someone can help with that?
// cbadk
Here's a picture of the about screen.
Picture of the grey connector would help.
Is there a diagram illustrating connection to the unit?
Sent from my Nokia 7 plus using Tapatalk
Here's a picture of the cable.
Btw it says "Mobile Inter" on the connector, so I would guess it's a connector for the USB 3G/4G modem, but I have never seen this connector before...
Color wise it looks like USB, 2 power pins and 2 data pins. You could check if there are 5 volts between red and black.
I found your thread because I'm also considering a Android headunit for my C5 III (2009). What radio was installed before and was the display a drop-in replacement or where any modifications necessary? Are you still satisfied with the unit?

Mtce chs canbus txd rxd wire

PX6 MTCE CHS CANBUS TXD RXD WIRE
4GB 64GB
I have unit with two wires which I am not sure what to do with?
1- CABUS TXD / IR-IN
2- CABUS RXC
what is the function of these wires and how to use?
In addition, i have additional port for front and reverse camera which reads
1- Rear Camera Power
2- Front Camera Power
3- Front Camera In
4- GND
so i am right assuming that I can directly give 12v power from wire number 1? but I have to use the trigger cable (pink reverse no-20 in wiring diagram) to be plugged in separately into the reverse parking trigger in the canbus already fitted for aftermarket stereo, MOST Fiber/Amp Bypass!
Did you figure this out?
mice got Same problem
burjtech said:
PX6 MTCE CHS CANBUS TXD RXD WIRE
4GB 64GB
I have unit with two wires which I am not sure what to do with?
1- CABUS TXD / IR-IN
2- CABUS RXC
what is the function of these wires and how to use?
In addition, i have additional port for front and reverse camera which reads
1- Rear Camera Power
2- Front Camera Power
3- Front Camera In
4- GND
so i am right assuming that I can directly give 12v power from wire number 1? but I have to use the trigger cable (pink reverse no-20 in wiring diagram) to be plugged in separately into the reverse parking trigger in the canbus already fitted for aftermarket stereo, MOST Fiber/Amp Bypass!
Click to expand...
Click to collapse
The txd and rxd are the wire for transfer data and receive data from the can system of the car. If your car does not have any original wires to connect them with, then you might need a canbus or you can try to directly connect them to your ODB connector for your car, it is normally below your steering wheel.

TEYES CC2+ 4 Wrangler

I purchased a rear view camera adapter for the Jeep Wrangler . Upon examination I see that the power and ground wires are labeled as follows: (Black wire GND) (Red wire B+) and the (yellow wire ACC).
When connected according to the wire ID tags the camera does not work.
After viewing adapters belonging to other CC2 & CC3 owners it appears that the wires on my adapter may be mislabeled.
Other cables are shown as RED ACC, and YELLOW B+
Everything else on the HU works very well.
Any ideas?

Head Unit not delivering enough Power…

Hey guys
So my headunit that I put inside my 2004 E46 does not support Apple CarPlay from the start.
The unit runs android (10)
I bought a adapter and tried to install the app that It comes with but nothing… no signal.
So the issue seams so be that there is not enough power coming out of the USB port from the headunit.
When I use a splitter and plug the end for power into the lighter usb charger and the data one into the usb dongle it works no problem but it looks ****ty …
Any way or any adapter that I can get this fixed with?

Categories

Resources