I purchased a rear view camera adapter for the Jeep Wrangler . Upon examination I see that the power and ground wires are labeled as follows: (Black wire GND) (Red wire B+) and the (yellow wire ACC).
When connected according to the wire ID tags the camera does not work.
After viewing adapters belonging to other CC2 & CC3 owners it appears that the wires on my adapter may be mislabeled.
Other cables are shown as RED ACC, and YELLOW B+
Everything else on the HU works very well.
Any ideas?
Related
After many hours of research and hands on work I have finished my in dash install in my MK4 Golf. Stock 5.0.2 with Timur's Kernel, Power Amp and Torque Pro.
First thing I'd like to say, I am HORRIBLE at plastic work. So my finished trim piece is not as clean as I'd like it to be but I had to stop and paint as I was just doing more harm than good. When I have some time I think I'm going to try and fix the trim, I'm going to see if there's someone local that can give me some pointers.
I used ABS cement to bond the trimmed metra kit to the modified trim piece, than I used plastic bumper filler to fill the gaps and finally sand prime and paint... Im a sound/electronic type guy with a small mechanical background.. NOT a body man. Lol
I wanted to make this a permanent install, contrary to the pre made trim pieces I could have bought that would have made the tablet removable. So I decided to mount it behind the trim piece rather than in the front. I also used PL Premium glue to hold the tablet in place.. This stuff is AMAZING.
http://www.lepageproducts.com/ProductDetail.aspx?pid=137
I relocated my Pioneer DEH-80PRS to the glovebox, made a secondary "kill switch" hidden in the ashtray and added 3 USB ports under the main trim piece just above the ashtray. Nice thing is I sourced the interior parts so I still have all the stock pieces in case I sell the car.
OK, so here's what I used:
Nexus 7 2013 (obviously)
OTG charging cable
http://www.amazon.ca/gp/aw/d/B00SMCJ8U6
Metra Double Din kit
http://www.amazon.ca/gp/aw/d/B002U5UD8C
For power I used this step down module
http://m.ebay.ca/itm?itemId=331477762049
Belkin Bluetooth receiver modified to accept power via USB (already owned one)
http://m.belkin.com/us/p/P-F8Z492/
And I also ordered a Bluetooth OBDII
http://www.amazon.ca/gp/aw/d/B009NPAORC
My deck has Bluetooth as well as 2 USB ports and 2 line in 1 rca input and 1 1/4 headphone jack. Now, I wanted to keep the Bluetooth available for my phone (nexus 6) so I used the belkin adaptor to receive the audio via Bluetooth from the tablet, convert it to line out and used a 1/4 jack to rca to input into my deck. The belkin receiver is located behind the tablet.
I then used 1 USB port from my deck to power the belkin and the other with an extension to one of the previously mentioned added ports. The other two are connected to a non powered hub (behind the tablet) and plugged into the OTG cable. From there I can freely plug in my USB sticks with music or movies and can swap them at any time.
I took an unused 12v accessory line from the fuse box ran it to the switch I mounted in place of the lighter (beside the ashtray) and from there to a relay. The relay takes constant power from the existing lighter power supply wires, and feeds the 12v downstep module located under the center console, (plugged into OTG cable of course) now depending on the position of the switch the tablet will turn on with the key, or accessory position of the key like the stereo does. This way if I don't want the tablet to turn on, say, in -30 Celsius I have this option.
Here are a few pictures I took with my nexus 6.
Hey Guys,
just Recived an Xtrons Head Unit for the Fiat Grande Punto. So yesterday we tryed to install it but what to say... it does not Start.
Maybe you guys know how to solve the problem?
btw. The Red (ACC) Wire is going to the can bus adapter and not to the iso plug, is that correct?
here you can see the photos: g o o . g l / 2 w j j v P
Thank you for helping.
nobody can help me to solve that problem?
Rajko2121 said:
Hey Guys,
just Recived an Xtrons Head Unit for the Fiat Grande Punto. So yesterday we tryed to install it but what to say... it does not Start.
Maybe you guys know how to solve the problem?
btw. The Red (ACC) Wire is going to the can bus adapter and not to the iso plug, is that correct?
here you can see the photos: g o o . g l / 2 w j j v P
Thank you for helping.
Click to expand...
Click to collapse
With a wire you need connect the ACC switched +12v power cable from at example the cigarette lighter to the related ACC +12v switched power on main HU harness connector.
On Fiat Grande Punto Mk199 switched +12v power is from vehicle canbus line.
So i need to connect an ne Cable from The Cigarette Lighter to the Red Cable which is going to the can bus Adapter and then connecting the new cable with the yellow 12v cable in the ISO socket, right?
EDIT: pls look at the new photo at the link in first post g o o . g l / 2 w j j v P
Rajko2121 said:
So i need to connect an ne Cable from The Cigarette Lighter to the Red Cable which is going to the can bus Adapter and then connecting the new cable with the yellow 12v cable in the ISO socket, right?
EDIT: pls look at the new photo at the link in first post g o o . g l / 2 w j j v P
Click to expand...
Click to collapse
you need connect to the related pin in main harness not on canbus box harness. Canbus boxes are usually powered from main HU harness
iRcKenny said:
you need connect to the related pin in main harness not on canbus box harness. Canbus boxes are usually powered from main HU harness
Click to expand...
Click to collapse
so just one wire from the lighter to the yellow 12V cable at iso plug?
PX6 MTCE CHS CANBUS TXD RXD WIRE
4GB 64GB
I have unit with two wires which I am not sure what to do with?
1- CABUS TXD / IR-IN
2- CABUS RXC
what is the function of these wires and how to use?
In addition, i have additional port for front and reverse camera which reads
1- Rear Camera Power
2- Front Camera Power
3- Front Camera In
4- GND
so i am right assuming that I can directly give 12v power from wire number 1? but I have to use the trigger cable (pink reverse no-20 in wiring diagram) to be plugged in separately into the reverse parking trigger in the canbus already fitted for aftermarket stereo, MOST Fiber/Amp Bypass!
Did you figure this out?
mice got Same problem
burjtech said:
PX6 MTCE CHS CANBUS TXD RXD WIRE
4GB 64GB
I have unit with two wires which I am not sure what to do with?
1- CABUS TXD / IR-IN
2- CABUS RXC
what is the function of these wires and how to use?
In addition, i have additional port for front and reverse camera which reads
1- Rear Camera Power
2- Front Camera Power
3- Front Camera In
4- GND
so i am right assuming that I can directly give 12v power from wire number 1? but I have to use the trigger cable (pink reverse no-20 in wiring diagram) to be plugged in separately into the reverse parking trigger in the canbus already fitted for aftermarket stereo, MOST Fiber/Amp Bypass!
Click to expand...
Click to collapse
The txd and rxd are the wire for transfer data and receive data from the can system of the car. If your car does not have any original wires to connect them with, then you might need a canbus or you can try to directly connect them to your ODB connector for your car, it is normally below your steering wheel.
Hi,
My Android head unit has 2 Front channels RCA output only. I'd like to bypass the onboard AMP ( AC7315 I presume ) to drive an external 4-channels unit. I do not want to use an adapter to convert the internal AMP output to low level signals, so i was wondering if solder two shielded cables on the rear channels input pins of the AC7315 integrated circuit could give me the missing 2 rear RCA output.
Any idea/suggestions?
Thnx.
M
I am having trouble getting support from the company I purchased my unit from. They are either very slow responding or just ignoring me. Didn't help that I didn't give them the best review in a follow up email. Anyway - maybe someone here can help me. No manual or instructions were provided. The unit is specific for 08 cadillac sts, plug n play adapter to the car doesn't match. I have the wiring diagrams and prepared to cut and splice directly to the car. There are 8 wires on the plug - yellow and black for continuous power - 4 speaker wires - and 2 wires that I don't have a clue where to connect them. I have asked for the instruction booklet or where these 2 wires are to be connected - no response. Any advice would be appreciated.