Got my Dasaita installed this weekend. The device is gorgeous and really makes my Jeep's dash come to life! I am having an issue that i can seem to fix. When I go to the amplifier app (EQ/Fader) it does nothing, nada, zilch! When i use the Poweramp EQ it comes to life and the sound is amazing. But when I use the regular radio or play music app it sounds flat.
Any idea what this could be? thanks in advance for any assistance I have researched all over and cant find an answer
I emailed Dasaita about the problem,. I will post the solution here for anyone else having a similar issue with this unit
Dasaita was of no help. I did however get some assistance from my Wrangler forum, go figure no one here even said hi, lmao
The solution was to set the canbus setting to 78 JEEP_Cherokee&Renegade&FiatAegea(Simple) and viola, now I have EQ once again. Thanks to everyone that read this thread and left no comment. To those that are having the same issue, you're welcome
Thanks ricanbandit,
I just installed this Week-End my Dasaita and i find the sound is fad too, compare to the OEM HeadUnit...
I'll try to change the canbus setting et Poweramp too.
Regards.
Related
Hello guys,
I need some help with these android head units.. I've ordered one on amazon by pumpkin and I've had some ups and downs with it..
a few questions:
Are there more advanced hus with more audio options for the pre amp outs? (time alignment, crossovers, etc..) - The Pumpkin only has basic 3 band EQ..
I've got a "BRRRP" sound after turning off the ignition -> turning off the radio and this is not very pleasent since its pretty loud. (Didn't have any problems with my sph-da120 by pioneer)
Are there some "major" brands which stand for quality?
Some "must have" apps enhancing the experience?
Sorry for asking these basic questions but it's very confusing and hard to get a clue after looking at all the threads in here..
Help would be very appriciated!
Best Regards,
Patrik
"I've got a "BRRRP" sound after turning off the ignition -> turning off the radio and this is not very pleasent since its pretty loud. (Didn't have any problems with my sph-da120 by pioneer)"
That part sounds a bit like the 12v to the antenna is turning off before the radio does, causing the radio to loose it's signal.
thanks for the comment!
gonna check that.
I also remembered that i have swapped the pins for ignition and 12v for my old pioneer hu, maybe this will help too
any help with the other questions?
Hello,
I got a very annoying problem with my pumpkin head unit. Theres a noise, like when you place a smartphone close to speaker, which I hear all the time coming out of my car speakers.
Sometimes it's quiet and sometimes I hear that noise.
Is there any way to fix that?
My HeadUnit is (Description from Pumpkin Website):
Pumpkin 7 Inch Quad Core Android 4.4 Car Stereo DVD Player for Opel Vauxhall 2 Din support DAB+ AV Output MirrorLink 3G WiFi OBD2 DVR Steering Wheel Control
I run Malaysk Rom, but had this issues even with the standard ROM.
Would be happy if anybody could help me.
Regards
Ben
bump
No ideas?
Any ideas
I would be happy if someone could help me with my Problem
It's likely noise from the screen. Try turning the screen off and see if it goes away. It won't be easy to fix. Make sure all your grounds are as good as possible and make sure they are as direct to the battery as you can get. Noise like this is from a bad circuit design. It's the difference between an expensive well-engineered board and some POS from China. Yeah, I got one too, the Lollipop unit (self-rooted w/Viper).
If you only get the noise when the car is running it could be noise from your alternator or plug wires. That's harder to fix. You could use one of the crazy capacitors they make for car audio, but if you aren't running a 1000W, they can be overkill. I would try 1000uF cap across the 12V battery supply to ground, as close to the head unit as you can get it. Make sure the cap is rated at least 15V or so (it will see more than 12 from a car!). It will be electrolytic, so make sure you obey polarity. I'll be doing this myself later today.
May be worth a try running a wire from the negative of the battery post to the radio ground...I would just do it quick and easy in the driveway before trying to route it through the car.
Thank you for your support on that...
Unfortunately that sounds not that easy. I thought this might be a common problem with those head units :-/
I have a sound coming thru the speakers as well kinda sounds like a hard drive reading data when its booting up but goes away once its booted & running.
Might try running a better ground see if that helps.
Hi there,
Since this is my first post i want to say hello to everyone!
I decided 3 weeks ago to buy an android head unit for my audi a3, since i was bored listening radio or audio cd;s only...
Audi OEM RNS-E navigation was an option but it's too expensive just to have navigation, bt, and mp3 in my car... so i decided to go for an android hu that fits my dash...
I found this Xtrons android HU and bought it....
I was aware about the poor sound quality BUT it's actually VER VERY bad!!! on standard 10 speakers Audi sound system... (i was ready to root the device and use viper4android, or any hardware mod to improve the sound)
BUT I was lucky to find a BOSE sound system which i retrofitted on my car, and now the sound it's much better... like 8/10
NOW the last problem that i'm facing is some background noise, which i can't explain where it came from.
It only happen when i plug in the xtrons head unit. I swapped to the original Audi HU and there is no background noise. This means the background noise is picked up / generated by the Xtrons HU.
The noise is like a continuous "buzz" plus 2-3 pops and it only appears when the unit is on pause, mute or very low volume AND ONLY WHEN I SWITCH THE IGNITION ON (NO ENGINE RUNNING), if i revers the ignition to 0 position the noise disappears.
If the engine is running the noise is there, but is very hard to hear due to the diesel engine...
This noise IS NOT a wining noise, like an alternator generated...
Anyone encounter this problem? Is there any fix?
Tomorrow i am going to replace all the Xtrons HU extension cables (audio/video in/out) with shielded cables, and if doesn't work, i'll try some ferrite(s) maybe it helps...
Thanks!
justincr83 said:
Hi there,
Since this is my first post i want to say hello to everyone!
I decided 3 weeks ago to buy an android head unit for my audi a3, since i was bored listening radio or audio cd;s only...
Audi OEM RNS-E navigation was an option but it's too expensive just to have navigation, bt, and mp3 in my car... so i decided to go for an android hu that fits my dash...
I found this Xtrons android HU and bought it....
I was aware about the poor sound quality BUT it's actually VER VERY bad!!! on standard 10 speakers Audi sound system... (i was ready to root the device and use viper4android, or any hardware mod to improve the sound)
BUT I was lucky to find a BOSE sound system which i retrofitted on my car, and now the sound it's much better... like 8/10
NOW the last problem that i'm facing is some background noise, which i can't explain where it came from.
It only happen when i plug in the xtrons head unit. I swapped to the original Audi HU and there is no background noise. This means the background noise is picked up / generated by the Xtrons HU.
The noise is like a continuous "buzz" plus 2-3 pops and it only appears when the unit is on pause, mute or very low volume AND ONLY WHEN I SWITCH THE IGNITION ON (NO ENGINE RUNNING), if i revers the ignition to 0 position the noise disappears.
If the engine is running the noise is there, but is very hard to hear due to the diesel engine...
This noise IS NOT a wining noise, like an alternator generated...
Anyone encounter this problem? Is there any fix?
Tomorrow i am going to replace all the Xtrons HU extension cables (audio/video in/out) with shielded cables, and if doesn't work, i'll try some ferrite(s) maybe it helps...
Thanks!
Click to expand...
Click to collapse
I have that problem with my Erisin, too. Curious whether your new cables will solve the noise problem. Please post it here, if it worked out :good:
justincr83 said:
Hi there,
Since this is my first post i want to say hello to everyone!
I decided 3 weeks ago to buy an android head unit for my audi a3, since i was bored listening radio or audio cd;s only...
Audi OEM RNS-E navigation was an option but it's too expensive just to have navigation, bt, and mp3 in my car... so i decided to go for an android hu that fits my dash...
I found this Xtrons android HU and bought it....
I was aware about the poor sound quality BUT it's actually VER VERY bad!!! on standard 10 speakers Audi sound system... (i was ready to root the device and use viper4android, or any hardware mod to improve the sound)
BUT I was lucky to find a BOSE sound system which i retrofitted on my car, and now the sound it's much better... like 8/10
NOW the last problem that i'm facing is some background noise, which i can't explain where it came from.
It only happen when i plug in the xtrons head unit. I swapped to the original Audi HU and there is no background noise. This means the background noise is picked up / generated by the Xtrons HU.
The noise is like a continuous "buzz" plus 2-3 pops and it only appears when the unit is on pause, mute or very low volume AND ONLY WHEN I SWITCH THE IGNITION ON (NO ENGINE RUNNING), if i revers the ignition to 0 position the noise disappears.
If the engine is running the noise is there, but is very hard to hear due to the diesel engine...
This noise IS NOT a wining noise, like an alternator generated...
Anyone encounter this problem? Is there any fix?
Tomorrow i am going to replace all the Xtrons HU extension cables (audio/video in/out) with shielded cables, and if doesn't work, i'll try some ferrite(s) maybe it helps...
Thanks!
Click to expand...
Click to collapse
Hey you. Did the new cables solve the problem? I'm asking because I want to get rid of the annoying sound, too.
Sc4r3Crow said:
Hey you. Did the new cables solve the problem? I'm asking because I want to get rid of the annoying sound, too.
Click to expand...
Click to collapse
Unfortunately, no, i didn't fix the annoying buzz
justincr83 said:
Unfortunately, no, i didn't fix the annoying buzz
Click to expand...
Click to collapse
It's a pity ?
Did you also try a noise suppressor or something like that?
Sc4r3Crow said:
It's a pity ?
Did you also try a noise suppressor or something like that?
Click to expand...
Click to collapse
Hey,
Has anyone found solution to this annoying noise ? I have installed XTRONS unit in my audi a3 and can't get rid of it. Have tried already ground loop isolators and ferrite filters with no luck.
Hi all.
I stumbled upon these forum by googling my issue. So far I haven't found any answers to my problems, so hoping for some help from the great people on here.
I have recently installed a seicane 10.1 android head unit into my jeep wrangler.
It appears to have a few little issues like audio is automatically somewhat louder on start up ...... but my main issue is
Only the radio app has sound.... no other apps have sound.
All speakers are working correctly with the radio app. Canbus setting is correct. But no sound output from the other apps.
If anyone has experienced this and can shed some light on it for me I would greatly appreciate it.
Thanks.
If it is a new unit,I guess you car may has factory amp,you need to connect the head unit amp harness to your car amp harness.
If the unit used for several months,then other apps no sound,I guess the main board is broken.
It is better for you to contact the seller for help.
May be a shot in the dark, but you might have hooked the amp wire up to the 'powered antenna' wire by mistake. If you tune to a radio station, that wire will get power and you will hear the sound, but if you are on a different app, that wire will not get power and you will not hear sound.
The amp wire coming from the radio will always have power and will work on all apps, and they are both blue and easy to confuse.
Pklains advice wprked for me.
The remote wire is black on the back of my unit. I accidentally hooked up blue antenna wire so it only powered amp when radio app was on.
I was NOT wiring it up incorrectly.
It was a software fault. I since got a replacement from the manufacturer (took 3 long months) since installing the replacement it worked perfectly.
hi ... same thing happened to me. Check your system. If your speaker lines is going through any amp, bridge, crossover or whatnot then do not supply CAR'S signal wire from ANDROIDS radio antenna signal wire (the android unit's antenna wire has +12v only when radio is on) - test audio by supplying 12v to your CAR'S signal wire. Simple yet it took me some time to figure things out. I hope this helps out someone who has the same problem.
Also it is not advisable to connect ANDROID amplified output to VEHICLES AMP - should be pre-amp from ANDROID to AMP or use LINE OUTPUT CONVERTERS or DIY (search speaker level to line level adapter ... a simple voltage divider worked for me) make sure you know car amps impedance before anything else ( industry standard is 10k )
I have the same problem with my PX6. The unit worked for a few months, but all of a sudden I only get sound from the FM radio.
Any advice?
duelago said:
I have the same problem with my PX6. The unit worked for a few months, but all of a sudden I only get sound from the FM radio.
Any advice?
Click to expand...
Click to collapse
did you find a solution to this? I sometimes get this, the only way for me to fix it is by doing a hard restart by pressing powerbutton for 15seconds
rowan112 said:
did you find a solution to this? I sometimes get this, the only way for me to fix it is by doing a hard restart by pressing powerbutton for 15seconds
Click to expand...
Click to collapse
I'm waiting for parts from China. Stuck in customs. I let you know if it is hard to replace and if it solves the problem...
duelago said:
I'm waiting for parts from China. Stuck in customs. I let you know if it is hard to replace and if it solves the problem...
Click to expand...
Click to collapse
Do you get this issue all the time or is it random?
for me it's random, i have to force restart the unit to get sound working on stuff that's not radio/beeps.
rowan112 said:
Do you get this issue all the time or is it random?
for me it's random, i have to force restart the unit to get sound working on stuff that's not radio/beeps.
Click to expand...
Click to collapse
I get it all the time, but it started with a lot of "static noice" from the speakers. That went away if I rebooted the device. The unit worked again for a few minutes and the problem with the noice was back. One day it just went totally silent except beep and FM radio
duelago said:
I get it all the time, but it started with a lot of "static noice" from the speakers. That went away if I rebooted the device. The unit worked again for a few minutes and the problem with the noice was back. One day it just went totally silent except beep and FM radio
Click to expand...
Click to collapse
ah so we are having different problems then
rowan112 said:
ah so we are having different problems then
Click to expand...
Click to collapse
I had to desolder the amplifier (TDA7851L) and replace it with a new one. Not easy, but everything works for me now
I don't see my exact problem, which is very similar to everyone here. I get sound from the Radio app - but if I use the Radio app, I lose sound everywhere else. I retain the ability to use the Radio for sound. This also happens upon a reset, as if it starts the radio first or something - but the app doesn't need to be started for that to be a problem. This started upon initial installation.
Fun thing: If I power off the car (battery still connected of course), wait a few minutes, then try stuff, I get sound everywhere. Until I use the Radio app, of course. Naturally it decides to reboot when it feels like it, so this is annoying.
I have an Eunavi HU. The same heppened to me after upgrading the firmware with a file provided by manufacturer. No sound, only on radio. After few messages with the manufacturer here is the solution that worked: Factory settings->DSP settings->ARM Audio Input Selection-> check Analog Input. Hope this solution will help someone.
HelloI have this problem with my ts10 hu
Hi. After changing Canbus setting in my android head unit, I haven't any sound in all app and radio in my HU. Please help me.
My first post here as I am hoping someone can help me out. I have an XY Auto '11-'15 Chevy Cruze Tesla Style Android. The model on the info screen claims it is a YT9213AJ but on the chip board it says YT9260 Ver. 1.2. My issue is volume and sound in general. From 1 to 19 the sound is flat; you go to 20 and it's as if the Loud feature kicks in. The Equalizer does not change sounds at all. What is weird is on the songs programmed to radio sound great at any volume level.
I'm good at installation, and I can work my way around a device but programming is something I'm not very good at. I'd root it and add a better interface but that's way above my knowledge. Any help would be much appreciated. I attached pics of info screen and chip board in my albums. Thank You!
Bought one for my cruze, and im facing a problem with the screen, but also looks like software problem. Smetimes start to move the screen alone. I tryed to update the firmware, but facing the same problem. Does anyone have any idea what could possible be?