i got usb wlan adapter. it's ip is 192.168.1.130.
the lan adapter in my pc has 192.168.1.84 ip.
all computers on my local wired network has 192.168.1.* addresses and 255.255.255.0 subnet.
i fixed the IP of SD sandisk wifi adapter on my mda compact to 192.168.1.131.
Usb adapter is in peer-to-peer (ad-hoc) mode and i normaly connect with ppc to it. i got 80-100% signal all the time.
the problem/question #1: why i cant ping from ppc to PC ? firewall turned off.
#2 - if i could ping it, would i be able to ping all the other ip's on my wired network?
#3 - if i could be able to ping all of those computers, how should i set-up a workgroup on ppc and be able to map network drives through wlan link?
#4 - if i would be able to map the drive over wifi link, would i be able to add mine 20.000 mp3s to the pocketmusic's playlist and play them wirelessly?
thanks in advance!
And when i ping from PPC - i see on pc that "received" packets are raising -
ie. now it shows 12 packets received, when i run ping on ppc to pc, the
number increases to 16 (4 pings!) but all are time-outed....
And if the IP on both sides are set to "automaticly", they got assigned
169.254.*.* IP's. Then the ping goes through correctly but i can't still
access the network. The network bridge between LAN and WLAN connection only
made things worser, making my internet connection unusuable (DSL through the
same LAN connection) so i deleted the bridge. Now - ping is going but i
still cant map my pc's drive.... what could be the problem...
Same problem
Dakky,
I have the exact same problem. I bought a Netgear WG111 Wireless USB dongle. I created an ad-hoc network, connected to it but can't connect to the internet or browse my shared. On my desktop the sent packet go up but not the recieved.
Are we both being stupid, can't you connect your PPC to your PC using an ad-hoc network? I have now tried to connect with two different desktops to my XDA and a friends XDA IIs running WM5 to my desktop but had no success. I can connect to an access point and browse file/internet no problem.
I have an XDA EXEC and run XP Pro on desktop.
I've got similar problem. I have Linksys Wireless-G usb network adapter, i assign same class IP adresses (192.168.2.1, 192.168.2.2, mask 255.255.255.0) the wifi connects in ad-hoc modebut how can sync over wifi ?, if I am able to sync over wify i will be able to use my pc's internet connection wich is a lot faster than any gprs/edge
I don't think you can network in this way - basically you have a bunch of clients but no 'server' I think you need a wireless hub (with Internet connection in there somewhere) in there somewhere.
If you do a search on microsoft web site ther is some info about using a PC as an internet share for other PCs but you have to use a very specific IP address rnge for this and set the share PC up in a certain way
I do not have Broadband internet. I got the Touch because the Internet Sharing option with Sprint PCS if free on my account. I what to share my Sprint EVDO connection with my Xbox360. Heres my setup...
1:HTC Touch in Internet Sharing mode via USB. IPv4:192.168.0.1 no DG
2:When trying to share connection to Ethernet port Windows wants the IPv4 of the Ethernet port to be 192.168.0.1. Windows give this error...
http://support.microsoft.com/kb/241769
Error 783: Internet Connection Sharing cannot be enabled. The LAN connection selected as the private network is either not present, or is disconnected from the network. Please ensure that the LAN adapter is connected before enabling Internet Connection Sharing.
I looked up this Error. It states that Windows wants the Ethernet port to be 19.168.0.1 and something else is using that IP already. The Touch uses that IP and I don't know how to change it or change the IP that Windows wants to use. Please Help!
Hi All,
I have a tough one to solve for a colleague..
He is wanting to use his HTC Snap (WM6.1) Data connection to allow his laptop to connect to office VPN(VPN client is on laptop).
ICS works great via USB for internet access only. The VPN subnet is the same 192.168.0.x subnet as the default IP assigned via ICS.
I changed the ICS DHCP assigned IP range to 192.168.10.x (via reg hacks) and internet works ok from Laptop still.
VPN connects successfully from laptop (Netgear Prosafe VPN client) and stays connected only I cannot access, ping or anything on the 192.168.0.x subnet through the VPN..
Internet continues to be accessible from laptop whilst VPN is 'connected'.
Any ideas anyone?
Thanks in advance.
I love the connection of the HTC HD2 WiFi router option which allows me to seamlessly connect to the internet to browse, email, download and chatting.
However I have been unable to use VPN properly. I am talking about the Windows XP VPN feature where the host computer accepts incoming connections and the client computer connects accordingly.
The VPN connection connects fine, however I cannot browse shared drives nor connect to the network printer. I know this problem exists when prior to the HTC HD2 in normal Windows Mobile 6, I used to connect to Bluetooth PAN and it has this problem as well.
I assume that being a Router-like program, the HD2 would work just like a router.
Has any HD2 users in this forum had success with WinXP VPN using the HD2 WiFi Router program?
I am able to connect to my home router's PPTP VPN server from my Android phone's PPTP client. I can even see my remote LAN devices; and, my remote LAN devices can see my mobile phone on the LAN.
The problem is when I connect my phone to wifi Internet.... BEFORE connecting to my PPTP VPN server... I can't see the remote LAN; and, the remote LAN can't see my phone. The only thing I can do successfully is get a new public IP (my home Internet public IP).
What can I do so that I am able to use my local wifi Internet connection to connect to my VPN at home?
It might be a route problem.
When you connect to WiFi, some static routes are pushed to your phone.
Those routes might not be refreshed or conserved after a VPN connection.
If it is not a route problem it's a default gateway problem.
Yes, that's what I suspected. I already tried adding routes; specifying the gateway via command-line; however, I didn't have any luck; probably because I didn't know exactly what I was doing.
One thing I noticed; when I use my wifi internet hotspot, I noticed that it gets a private WAN IP.. 10.x.x.x; which then NATs to a temporary real public IP; which no connections instigated from the outside world can make it So, even if I do port-fowarding on my wifi hotspot router, it doesnt help any since the incoming connections are stopped dead in their tracks.
I'm using PPTP VPN; which depends on a TCP port 1723. If that TCP connection is instigated from my remote VPN server into my mobile Internet wifi hotspot based LAN devices, it wouldn't work for the same reason explained above. I didn't see a PPTP VPN passthrough option for my wifi hotspot; only for IPSEC; which I dont have a server for. I'm guessing that if I had a real-world public WAN IP for my mobile Internet hotspot, maybe I wouldn't have this problem for PPTP.??
maaaaz said:
It might be a route problem.
When you connect to WiFi, some static routes are pushed to your phone.
Those routes might not be refreshed or conserved after a VPN connection.
If it is not a route problem it's a default gateway problem.
Click to expand...
Click to collapse
First, are you talking about a free internet hotspot or from private internet hotspot (@work for example) ?
you'll never gonna get a public IP from your internet hotspot. 1-public-IP-for-1-client on a hotspot is just inconceivable, due to IPv4 exhaustion.
I think you only have to try to do port forwarding on your hotspot.
Your assumption "it doesnt help any since the incoming connections are stopped dead in their tracks" is wrong I guess. If your hotspot has a built-in firewall, it might be stateful. As you are initiating a connection to your server, the returned traffic flow shall be allowed.
If it doesn't work after port forwarding, try to look at firewall rules on your hotspot router.
Problem resolved.
My Verizon wireless hotspot (890L) doesn't support PPTP passthough. More specifically, PPTP's routing protocol: GRE (value 47). Verizon does offer another wireless hotspot that does offer support for PPTP; at least via a firmware update.
This issue actually pushed me to install and configure OpenVPN server on my router; instead of using the existing PPTP server which I already had. OpenVPN is fantastic is working through firewalls.
Great !
Yes, OpenVPN is a delight.
me too
I have the same problem,
but I usually change another ROM until there's no bugs
mkanet said:
I am able to connect to my home router's PPTP VPN server from my Android phone's PPTP client. I can even see my remote LAN devices; and, my remote LAN devices can see my mobile phone on the LAN.
The problem is when I connect my phone to wifi Internet.... BEFORE connecting to my PPTP VPN server... I can't see the remote LAN; and, the remote LAN can't see my phone. The only thing I can do successfully is get a new public IP (my home Internet public IP).
What can I do so that I am able to use my local wifi Internet connection to connect to my VPN at home?
Click to expand...
Click to collapse
have you tried to configure the wi-fi gateway to match your vpn router?
settings / wireless & networks / wi-fi / long press your vpn connection / modify network / scroll to show advanced options / select static ip /scroll down to gateway and put the gate address in / save
I run a vpn through a 2 router setup, and even though my phone connects to the vpn router, its gateway by default is always the non-vpn router. changing the gateway to the vpn router allows the vpn to connect to the phone. you can verify the vpn connection by going to ip-score.
That why i can't see my phone using wifi in VPN network..
cant connect if theres no mobile data or load
Hi please help ..when i have load i see its connected..but if i have no load its not connecting please ..anyone can explain this?
mkanet said:
I am able to connect to my home router's PPTP VPN server from my Android phone's PPTP client. I can even see my remote LAN devices; and, my remote LAN devices can see my mobile phone on the LAN.
The problem is when I connect my phone to wifi Internet.... BEFORE connecting to my PPTP VPN server... I can't see the remote LAN; and, the remote LAN can't see my phone. The only thing I can do successfully gets a new public IP (my home Internet public IP).
What can I do so that I am able to use my local wifi Internet connection to connect to my VPN at home?
Click to expand...
Click to collapse
before I was able to connect the VPN from work and home but now I can able to connect from work only,,, the same VPN not working at home.. on my same MOB device
Please help me to fix this issue