I am currently using Google Translator.
i am korean
i have sm-g928v verizon model
I found sm-g928v rom on the internet so odin flashed( 6.0.1 ver)
There was a problem.
An error occurred when trying to downgrade(5.1.1)
- 5.1.1 : G928VVRU2AOJ3
- 6.0.1: ALL_VZW_G928VVRS3BPI1_G928VVZW3BPI1_CL8887762_QB10881516_REV00_user_low_ship.tar
The difference is VRU2AOJ3 and VRS3BPI1 , There is only one digit in the middle.
6.0.1 to 5.1.1 downgrade odin flash fail log
----- ODIN LOG -----
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G928VVRU2AOJ3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> modem.bin
<ID:0/004> param.bin
<ID:0/004> recovery.img
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
----- END ODIN LOG -----
and phone download mode
sw rev. check fail. device: 3, binary: 2
Please understand and help me. I want to downgrade.
V R U 2 A O J 3
_ _ _ 2 _ _ _ _ bootloader Version 2
V R S 3 B P I 1
_ _ _ 3 _ _ _ _ bootloader Version 3
must be same bootloader OR higher (Risky)
cannot downgrade to lower bootloader
Related
Ok long story short I wiped my stock ROM from my phone.. Samung Galaxy S Victory 4G LTE Virgin Mobile I have been trying for half a day to get answers & step-by-step instructions on how to fix my phone without success.. I have attempted to fix the issue myself again with no success. These are the steps I have taken thus far
Downloaded the following TAR
COMBINATION_L300VPALH1_L300SPRALH1_934170_REV00_user_low_ship.tar.md5
Started ODIN 3.4
Connected Device
Started the MD5 file following results
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> COMBINATION_L300VPALH1_L300SPRALH1_934170_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sbl1.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl2.mbn
<ID:0/004> sbl3.mbn
<ID:0/004> aboot.mbn
<ID:0/004> rpm.mbn
<ID:0/004> tz.mbn
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> userdata.img.ext4
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
My phone says
ODIN MODE
Product Name: SPH-L300
Custom Binary: Download Yes (1)
Current Binary: Samsung Offical
System Status: Custom
Qualcom Secureboot Enable
ODIN: Invalid ext4 image
if anyone could please help, I just want my phone back so I can call my family for Christmas.
Thank You
McTavish
hello
i have been flashing roms for ages now and really never had such a problem like this before , i am on sweet rom , model number N910U ( new zealand ) , i need to go back to stock rom cause there to been a hardware problem with the camera, thought i better get back to stock before i take it in .
i have unsuccessfully trying to unroot via odin ( Odin3 v3.09) tried using this firmware "BRI-N910UXXU1BOGB-20150731100307" and even had worse luck with this one " CTI-N910UXXU1BOE1-20150721100509" (fails in a few seconds)
seems to have failed just before it gets to hidden.img
heres the log :
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910UXXU1BOGB_N910UZZT1BOGB_N910UXXU1BOGB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Hello,
I have the same problem on the S5+ and for the moment i don't find solution for this problem. I think CSC is causing this error and my advice is to install samsung phone info to find CSC and download right firmware for your phone. After that you can try to reinstall with Odin the firmware .
Sent from my SM-G901F using Tapatalk 2
I restarted my phone and it went into FRP lock. I can only access download mode and do not have access to recovery. I have tried downloading stock firmware using Odin but it fails every time. When ever I download something from Odin I get this
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> cm.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> cm.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
and then in my phone it says "secure fail check : (Bootloader)"
Any suggestions on how I can get into my phone!?
Try using Samsung smartswitch while phone is in download mode and use the reinstall feature and see if that cannot help you get back to stock (and a working phone)
I have SM G928F , had same problem. I downgraded the bootloader and succeeded in putting new recovery on my phone and then flashed custom Rom….
Hope this helps.
Mazzie
Hello everyone, mazzie66 could you please explain how you downgraded your bootloader. Thanx
s6 edge+ bricked by frp
I bought second hand s6 edge + g928f blocked google account.
i have the imei and s / n number but i do not know what firmware it had on it.
now it's just download mode or recovery.
I flashed 3-4 firmware stock successfully, but it gets into recovery when it opens.
I used odin / z3x.
I have edited the firmware and combined them with boot / modem / sboot / hidden etc.
I searched in vain how I could learn the former firmware version.
with the smart switch after entering the model and telling her to contact the service center. with kies the same. i just know it is 7.0 encoded vodafone romania.
I've had some bugs with drk.
I would like to ask you how to install a custom rom (twrp) or pass frp lock.
Sorry for English.
This video can help to fix the black, bricked Samsung Galaxy phone, wish helpful with you.
https://www.youtube.com/watch?v=zXSHe3oorIM
Hello,
when I start my device then the error "Custom Binary blocked by FRP lock" comes.
I knew the error (OEM-unlock) not activated after root.
So, now I want to flash the new firmware with odin.
My handy model: SM-A310F
I downloaded the right firmware (I think) on sammobile (version: A310FXXU3CQL2) but when i want to flash it with Odin, it stops by hidden.img (~90%) with an error. (checkout log)
Log from Odin:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1301)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 3048 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> cm.bin
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
So, what can I do now?
Hi to all i have the samsung j3 (J320M J3xlte) whit los 14.1 and tried to revert into stok rom but i flash te firmware ARO (J320MUBU0ARD1_J320MUUB0ARE1_J320MUBU0ARB1) and get this error
Odin log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> J320MUBU0ARD1_J320MUUB0ARE1_J320MUBU0ARB1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> nvitem.bin
<ID:0/004> param.lfs
<ID:0/004> PM_sharkl_arm7.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
and see this message in the phone: ´´Firmware upgrade encountered an issue. please select recovery mode in kies and try again´´ but also kies and smartswitch dont detect my phone y tried whit anoter firmware and get te same error in odin
i need help and sorry for my bad english