hello
i have been flashing roms for ages now and really never had such a problem like this before , i am on sweet rom , model number N910U ( new zealand ) , i need to go back to stock rom cause there to been a hardware problem with the camera, thought i better get back to stock before i take it in .
i have unsuccessfully trying to unroot via odin ( Odin3 v3.09) tried using this firmware "BRI-N910UXXU1BOGB-20150731100307" and even had worse luck with this one " CTI-N910UXXU1BOE1-20150721100509" (fails in a few seconds)
seems to have failed just before it gets to hidden.img
heres the log :
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910UXXU1BOGB_N910UZZT1BOGB_N910UXXU1BOGB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Hello,
I have the same problem on the S5+ and for the moment i don't find solution for this problem. I think CSC is causing this error and my advice is to install samsung phone info to find CSC and download right firmware for your phone. After that you can try to reinstall with Odin the firmware .
Sent from my SM-G901F using Tapatalk 2
Related
hello - I have S4 9505 and I try to Upgrade Firmware from BTU-I9505XXUDMH8 to new Firmware TGY-I9505ZHUDMH6 and I get an error in odin 3.7 FAIL
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505ZHUDMH6_I9505ZZHDMH6_I9505ZHUDMH6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sbl2.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl3.mbn
<ID:0/004> rpm.mbn
<ID:0/004> aboot.mbn
<ID:0/004> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
Thanks for the help
after flashing the I9505XXUDMH8 due to new Samsung Shenanigans u can only go UP with upgrade... so u can't install mh7-6-5-4-3- ecc.
U can install only above I9505XXUDMH8 :/
Same problem here
any Solutions ?
just wait for new buildnumber or experimenral downgrade
Sent from my GT-I9505 using Tapatalk 2
There is a new firmware I9505ZHUDMI1 which is released after the MH8 so its a higher version, but this firmware update also fails via ODIN
samsung has absolutely screwed up the S4, lousy knoxx stuff which is a pain to remove manually
any ideas anyone on how we can go back to an old firmware or how do we even udpate so called new firmware
Hi everyone,
Tried installing HK version of Lollipop onto my Australian Note 3 using Odin. encountered an error and ended up soft bricked.
Searched various forums and posts and tried to flash the Telstra N9005XXUENE3_N9005TELENE1_N9005XXUENE3_HOME.tar.md 5 which is the stock rom I had on it before.
However Odin keeps failing with this error message:
ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUENE3_N9005TELENE1_N9005XXUENE3_HOME.tar.md 5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl1.mbn
<ID:0/004> rpm.mbn
<ID:0/004> tz.mbn
<ID:0/004> sdi.mbn
<ID:0/004> NON-HLOS.bin
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> modem.bin
<ID:0/004> cache.img.ext4
<ID:0/004> hidden.img.ext4
<ID:0/004> FAIL! (Ext4)
<OSM> All threads completed. (succeed 0 / failed 1)
Have tried everything! please help!!
please try flashing again, but use a lollipop pit file for your device. (PIT file is not the same for HK Version and N9005)
how did you go flashing hk version. i want to update to stock lollipop but im not sure what version to use. will latest do? i have a telstra sm-n9005.
CheapMerc said:
how did you go flashing hk version. i want to update to stock lollipop but im not sure what version to use. will latest do? i have a telstra sm-n9005.
Click to expand...
Click to collapse
Hi,
HK version was no good...I ended up using the Polish version which worked fine.
Try that one.
mukid728 said:
Hi everyone,
Tried installing HK version of Lollipop onto my Australian Note 3 using Odin. encountered an error and ended up soft bricked.
Searched various forums and posts and tried to flash the Telstra N9005XXUENE3_N9005TELENE1_N9005XXUENE3_HOME.tar.md 5 which is the stock rom I had on it before.
However Odin keeps failing with this error message:
ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUENE3_N9005TELENE1_N9005XXUENE3_HOME.tar.md 5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl1.mbn
<ID:0/004> rpm.mbn
<ID:0/004> tz.mbn
<ID:0/004> sdi.mbn
<ID:0/004> NON-HLOS.bin
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> modem.bin
<ID:0/004> cache.img.ext4
<ID:0/004> hidden.img.ext4
<ID:0/004> FAIL! (Ext4)
<OSM> All threads completed. (succeed 0 / failed 1)
Have tried everything! please help!!
Click to expand...
Click to collapse
try to download the latest stock rom for your mobile in sammobile. After that try to flash via ODIN
I restarted my phone and it went into FRP lock. I can only access download mode and do not have access to recovery. I have tried downloading stock firmware using Odin but it fails every time. When ever I download something from Odin I get this
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> cm.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> cm.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
and then in my phone it says "secure fail check : (Bootloader)"
Any suggestions on how I can get into my phone!?
Try using Samsung smartswitch while phone is in download mode and use the reinstall feature and see if that cannot help you get back to stock (and a working phone)
I have SM G928F , had same problem. I downgraded the bootloader and succeeded in putting new recovery on my phone and then flashed custom Rom….
Hope this helps.
Mazzie
Hello everyone, mazzie66 could you please explain how you downgraded your bootloader. Thanx
s6 edge+ bricked by frp
I bought second hand s6 edge + g928f blocked google account.
i have the imei and s / n number but i do not know what firmware it had on it.
now it's just download mode or recovery.
I flashed 3-4 firmware stock successfully, but it gets into recovery when it opens.
I used odin / z3x.
I have edited the firmware and combined them with boot / modem / sboot / hidden etc.
I searched in vain how I could learn the former firmware version.
with the smart switch after entering the model and telling her to contact the service center. with kies the same. i just know it is 7.0 encoded vodafone romania.
I've had some bugs with drk.
I would like to ask you how to install a custom rom (twrp) or pass frp lock.
Sorry for English.
This video can help to fix the black, bricked Samsung Galaxy phone, wish helpful with you.
https://www.youtube.com/watch?v=zXSHe3oorIM
Hello to all,
i am using an S4 GT-I9500 indian variant,
while flashing the phone with the stock firmware i did a mistake and clicked on the wrong button "BL" instead of "AP"
in my ODIN software and the operation failed with the button "BL".
now i tried to installing the firmware by using the "AP" button but i am getting the following message in the ODIN
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9500XXUHPI2_I9500YDDHPI1_I9500DDUHPE1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
i have tried it using recovery mode with CWM and TWRP boot loaders, and i am not able to wipe the data using the TWRP boot loader.....
and even tried connecting to samsung Kies it gives me an error message as "GT-I9500" does not support initialising....
so can anyone please help me get my phone back to running....
Thanks in advance......
Are you flashing the latest stock ROM with Odin?
STOCK Rom
Are you flashing the latest stock ROM with Odin?
Yes, My phone was stuck in Samsung logo (Boot loop)
So i tried flashing it with the stock ROM with Odin
when i tried it did not complete the flashing, instead it ended up with a Blank screens with the message that "Firmware encountered an issue please select recovery mode in Kies and try Again".
And when i try flashing the Stock ROM with Odin this the following tread that i am getting.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9500XXUHPI2_I9500YDDHPI1_I9500DDUHPE1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Tried using Odin 3.07, the original Samsung usb cable, or a different usb 2.0 port?
Hi to all i have the samsung j3 (J320M J3xlte) whit los 14.1 and tried to revert into stok rom but i flash te firmware ARO (J320MUBU0ARD1_J320MUUB0ARE1_J320MUBU0ARB1) and get this error
Odin log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> J320MUBU0ARD1_J320MUUB0ARE1_J320MUBU0ARB1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> nvitem.bin
<ID:0/004> param.lfs
<ID:0/004> PM_sharkl_arm7.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
and see this message in the phone: ´´Firmware upgrade encountered an issue. please select recovery mode in kies and try again´´ but also kies and smartswitch dont detect my phone y tried whit anoter firmware and get te same error in odin
i need help and sorry for my bad english