I need the manual cdma programming code of my htc ozone. I already try ##000000 and ##778 its now working do you have any idea what is the code?
Thanks,
You may need to Application Unlock your phone first. You can use SDA_AplicationUnlock
Run from PC when phone connected
Tutorial Inject on Sprint Samsung Galaxy Tab-P100 SPH
Software:
- QPST 2.7 build 323
- QPST 2.7 build 215
- CDMA Workshop 2.7
Others that need to be prepared as well:
- Number Flexi/Esia/Smartfren ready diinject
- Akey (26 digits) is obtained from the gallery
- PRL (from galeri)
There are 4 steps so that you can use both text and data
- Unlock MSL / SPC CODE
- Setting Akey, MIN and MDN in order to do sms.
- Setting EVDO
- Final Setting
FIRST STEP (UNLOCK MSL / SPC CODE):
- Install the application from the Android Market: connectbot
In the lower left corner to move to the local type in any name and then let the Android will go into a black screen logo $ dng
- Type: getprop ril.MSL
MSN / SPC you I 6-digit code will appear
STEP TWO (SETTING Akey, PRL, MIN and MDN)
1. Install CDMA Workshop
- The first thing to do is to enter Akey, the 26-digit number given by the Custemer service when registering card number.
- How to enter into Gtab Akey must be signed in diag mode -> press # # 8778 # to enter the menu to the MODEM Phoneutil replace PDAto modem
Do not forget in a position Gtab USB debuging (go to settings - application - development - USB debuging)
- Note on the control panel - System - Hardware - Device Manager. Looking at what ports samsung gtab installed, (eg) on COM port 7.
Open Workshop CDMA (CDMA WAS), select (eg) COM 7, and then press CONNECT.
Select READ
- Next you need to unlock Gtab to enter the MSL / SPC to do on the security tab and enter your SPC "6 digits" and press send, after a statement that HP can be unlocked then you are ready to enter Akey.
- In the CDMA workshop, typing or copy and paste the 26 digits Calculator Akey Akey on like the image above in the Dec, only 20 digits will be accepted Dec. text box is.
- Then automatically on Colom will appear Akey Hex Hex, you can check whether Akey terrsebut ESN is correct by entering the column and then click calc ESN, the checksum will pop up the last 6 digits of your 26-digit Akey, if true, then the Hex Akey already ready to use, copy and paste from the column Hex to Colom-Akey Cave and select write.
- your akey has been wrote on your device
2. Install QPST 2.7 build 3.2.3, plug into your PC and open Gtab QPSTConfiguration program.
- Select Add New Port, and select COM 7 (eg) corresponding config on CDMA WAS
- Select the Start Clients, select SERVICE PROGRAMMING and select an active phone
- Tap OK in the Phone Selection
- Click READ FROM PHONE, press OK if MSL Code appears.
On the Settings tab,
Slot Cycle Index: 2
Current NAM: NAM1
Auto NAM: unchecked
In Tab CDMA, fill in the following parameters:
NAM Name: Flexi
Directory #: No MDN (no flexi complete with area code, but the writing without the written numbers from 0 eg 02144445555 2144445555)
AOC: 2
CDMA
- MCC: 510
- 11_12: 00
- IMSI_S: No MIN (same as no MDN)
- Registration terminated (Checked All - Home SID - SID Foreign Foreign NID)
- Primary Channel A: 119
- Channel Primary B: 384
- Secondary Channel A: 78
- Channel Secondary B: 777
In Tab CDMA-2 (Optional)
NAM Name: Flexi
Directory #: No MDN (same as the MDN)
CDMA / True IMSI:
- MCC: 510
- 11_12: 00
- IMSI_S: No MIN (the same as the MDN)
- AOC: 2
In Tab AMPS Ignore
In Tab System
HOME SID / NID (Double click)
Fill with parameters:
- SID: 10 496
- NID: 65 535
Preferred Mode and so on selected Automatic
In Roam Tab
NAM Name: Flexi
Directory: No MDN (no flexi complete with area code, but the writing without the written numbers from 0 eg 02144445555 2144445555)
AOC: 2
Enter the PRL Preferred Roaming with the browse button click: select dr hard drive where you store the PRL
On the Display tab
Display Items:
- Banner: TELKOMFlexi (or may pake your name, ill effect to the existing parameters)
- Backlight: always on
INJECT ALREADY FINISHED.
Press the Write to Phone, ignore if there is an error. Then Gtab will restart, after restart should be able to sms.
STEP THREE (ACTIVATE EVDO)
Prior to this step is done please register in advance for your flexi mobile broadband it by typing PROMO (space) MONTHLY send to 2255
After that there will be information that your broadband has been active with the user id: [email protected] and password: your ESN
1. Through QPST 2.7 build 3.2.3
Gtab plug into your PC and open QPST Configuration program
Select Add New Port, and select COM 7 (eg) corresponding config on CDMA WAS
Clients select Start, select SERVICE PROGRAMMING and select an active phone
Press OK in the Phone Selection
Press the READ FROM PHONE, press OK if MSL Code appears.
2. In the M. IP tab
In the User Profile, select the profile 0, press the edit
- Fill in the parameters of the NAI: [email protected] (or [email protected] for smart isp)
- Fill in the parameters in the Tethered NAI: [email protected] (or [email protected] for smart isp)
- Home Address: 0.0.0.0
- Primary HA Address: 255.255.255.0
- Secondary HA Address: 0.0.0.0
- And press OK
In the User Profile, select a profile, repeat the process as the point a.
Mobile IP Behavior: Simple IP Only
3. On the PPP tab Config
Select the UM
In the PPP Authentication:
Contents Tethered NAI: [email protected] (or [email protected] for smart isp)
User ID: [email protected] (or [email protected] for smart isp)
Password: No. ESN
Check Optimized Dormant Handoff
Then Select AN
User ID: [email protected] (or [email protected] for smart isp)
Password: No. ESN
Others, are ignored.
4. In Tab RmNet
Select Device 0, click Edit ---> if no live Add
Check the "Enable Auto Connection", click OK
5. CLICK "wite to Phone"
Setting Gtab Completed.
After restarting the logo should appear on the notification of 3G already.
FINAL STEP
Unistal QPST 3.2.3 and install QPST 2.1.5
Go to the Service Programming menu.
Then on the PPP tab, fill in data such as fill on the PPP tab in QPST 2.7 Build 323.
After that write to phone again, then it will restart again gtab.
When finished restart, (For those who berOS Froyo) do a move like that anymore diawal2
Go to the application type in the search field NOTE # # 8778 # -> enter phoneutil, change the settings of the modem to the PDA.
thanks
source
http://www.kaskus.us/showthread.php?t=10869930
Big event！i can't get spc on my l720, when i use the app ''get my msl'' to get spc on l720,it said ''could not get property fil.msl'' .that's all my fault i guess. when i used dfs to write my akey on l720 ,i entered the wrong code,I seemed to change spc code instead of the code to change akey. here is the coed to change spc :
Code:
00
4B13030000000000* o- \" C7 E/ q/ R, e
4B130F006E766D2F6E756D2F383500
4B1308006E766D2F6E756D2F383500
4B13020041020000B60100006E766D2F6E756D2F383500
4B1305000000000000000000303030303030
4B13030000000000
, when i executed the code ''4B1305000000000000000000303030303030'' , i typed the code ''4B1305000000000000000000ea27dda95753******'' ，after that ,i can't get spc on my l720, when i use the app ''get my msl'' to get spc on l720,it said ''could not get property fil.msl''.
with out spc ，i can do nothing about this phone ,please help me!!!
Redmi note 3 only support intra-band Carrier aggregation(same band), it does not support inter-band Carrier aggregation(multiple bands)
Steps to enable Carrier aggregation on Redmi Note 3 Pro
Reliance JIO and Airtel in India supports carrier aggregation.
JIO supports Band 3+5, Band 5+40 or Band 3+40 ( 3+5 is stable)
Airtel supports Band 3+40 in some states.
To enable carrier aggregation on this handset, please follow these steps. It can be used for other handsets also.
PREREQUISITES:
1. The bootloader must be unlocked.
2. Phone must be rooted.
3. ADB should be installed and phones USB debugging mode must be ON.
4. Install QPST and QXDM tools
Link to QXDM tool:
https://drive.google.com/open?id=1kV...M3-XNdZYO9HF94
Link to QPST
https://androiddatahost.com/np4wq
STEPS:
1. Connect the phone to PC via USB with the phone in ON state.
2. Open the command prompt with administrator rights.
3. Go inside ADB folder via command prompt.
4. Type <adb devices> Your phone must be listed there if everything is alright.
5. Type <adb shell>
6. Type <su> You must grant SU permission in the phone.
7. Type <setprop sys.usb.config rndis,diag,adb>. You will hear beep. It means your phone entered in diagnostic mode.
8. Then open QXDM professional tool. Go through options>communications and select your phone port in target port
9. Click NV Browser in View section. Go to RF LTE in category filter.
10. For B3+B5 CA, find RFNV LTE B3 CA BC CONFIG AND click Read at the right bottom. This will read default values. Type 20 and click Write to overwrite the values. Similarly, find RFNV LTE B5 CA BC CONFIG and type same value 20 to enable CA both 2 Bands and reboot phone. You will see 4G+ when CA is active.
11. To enable CA on other combination of Bands, download NV calculator by vndnguyen from Play Store. In LTE Bands section, select Bands of your choice and it will tell you the Decimal value to overwrite. For example, for Band 3+5 combination, it is 20.
12. Reboot phone.
Link to Youtube
https://youtu.be/T5fjbvip4Yc
_____
Nice work
Also how to change to default?
Saltmango said:
Steps to enable Carrier aggregation on Redmi Note 3 Pro
Reliance JIO and Airtel in India supports carrier aggregation.
JIO supports Band 3+5, Band 5+40 or Band 3+40 ( 3+5 is stable)
Airtel supports Band 3+40 in some states.
To enable carrier aggregation on this handset, please follow these steps. It can be used for other handsets also.
Click to expand...
Click to collapse
Can you show the speed difference on LTE and LTE CA with same network at same location?
Deepz8 said:
Nice work
Also how to change to default?
Click to expand...
Click to collapse
Put 0 in value. Or save the old value somewhere
samrat_castle said:
Can you show the speed difference on LTE and LTE CA with same network at same location?
Click to expand...
Click to collapse
I can't see any big difference, when i test i got only 2mbps difference
Insted of that long process you can use network signal guru available on play store
It also requied root
https://play.google.com/store/apps/details?id=com.qtrun.QuickTest
android_smater said:
Insted of that long process you can use network signal guru available on play store
It also requied root
https://play.google.com/store/apps/details?id=com.qtrun.QuickTest
Click to expand...
Click to collapse
Yeah, tried that! Network only latch on to band 3.
Working or not ? Not sure !
Enabled for me in B3 + B7 (France).
Logo shows 4G+. I thought it was not working but it seems to be working. Sometimes I can see B3 and B7 even if there's no difference on download speed: strange !
View attachment 4394922Does it use more battery?
Works for me
Saltmango said:
Steps to enable Carrier aggregation on Redmi Note 3 Pro
Reliance JIO and Airtel in India supports carrier aggregation.
JIO supports Band 3+5, Band 5+40 or Band 3+40 ( 3+5 is stable)
Airtel supports Band 3+40 in some states.
To enable carrier aggregation on this handset, please follow these steps. It can be used for other handsets also.
PREREQUISITES:
1. The bootloader must be unlocked.
2. Phone must be rooted.
3. ADB should be installed and phones USB debugging mode must be ON.
4. Install QPST and QXDM tools
Link to QXDM tool:
https://drive.google.com/open?id=1kV...M3-XNdZYO9HF94
Link to QPST
https://androiddatahost.com/np4wq
STEPS:
1. Connect the phone to PC via USB with the phone in ON state.
2. Open the command prompt with administrator rights.
3. Go inside ADB folder via command prompt.
4. Type <adb devices> Your phone must be listed there if everything is alright.
5. Type <adb shell>
6. Type <su> You must grant SU permission in the phone.
7. Type <setprop sys.usb.config rndis,diag,adb>. You will hear beep. It means your phone entered in diagnostic mode.
8. Then open QXDM professional tool. Go through options>communications and select your phone port in target port
9. Click NV Browser in View section. Go to RF LTE in category filter.
10. For B3+B5 CA, find RFNV LTE B3 CA BC CONFIG AND click Read at the right bottom. This will read default values. Type 20 and click Write to overwrite the values. Similarly, find RFNV LTE B5 CA BC CONFIG and type same value 20 to enable CA both 2 Bands and reboot phone. You will see 4G+ when CA is active.
11. To enable CA on other combination of Bands, download NV calculator by vndnguyen from Play Store. In LTE Bands section, select Bands of your choice and it will tell you the Decimal value to overwrite. For example, for Band 3+5 combination, it is 20.
12. Reboot phone.
Link to Youtube
https://youtu.be/T5fjbvip4Yc
Click to expand...
Click to collapse
What is the value of B40? Like 20 or 54?
android_smater said:
Insted of that long process you can use network signal guru available on play store
It also requied root
https://play.google.com/store/apps/details?id=com.qtrun.QuickTest
Click to expand...
Click to collapse
I have that app. How to enable carrier aggregation?
[email protected] said:
I have that app. How to enable carrier aggregation?
Click to expand...
Click to collapse
Uper right 3 dots band locking
Done
Use network signal guru app to find two good bands in ur area and follow the guide.. i hav added band 3 and 40
if any other app show which band connted
With forced band (for CA) download speed is worst so I've reverted back to original values.
We can find lots a topics about CA problems on Xiaomi phones... and that's right, sadly.
Link to QXDM tool not working. Gdrive link not found.
Link OK
The good link : https://drive.google.com/file/d/1kVG4ewkHg4_wHeWK94M3-XNdZYO9HF94
saginesht said:
Done
Use network signal guru app to find two good bands in ur area and follow the guide.. i hav added band 3 and 40
Click to expand...
Click to collapse
how much speed?
mathan7 said:
how much speed?
Click to expand...
Click to collapse
Not much difference.... I get around 2-3 MBps in uc browser
Snapdragon 439 support 2ca but i tried to enable it via qxdm for band (3+40) and tried to write rfnv lte b3 ca bc config and rfnv lte b40 ca bc config with the value but both showed no such file exist and when tried to forcefully write the value, the network gone and radio modem seemed to restart automatically
Though recovered it by writing both values as 0