Related
I put here my experience to install any ROM on your U8800Pro (these also applies to U8800 but you need the official GB)
To upgrade from 2.2 to 2.3
[you can use the following when you have any problem in installing a new ROM on your mobile (or if you have a blue secreen) ]
1. Download this archive (190MB) http://www.multiupload.com/NIIJC5BK83 which conatins two files od the official GB 512: U8800PV100R001C00B512G00.zip (you can also download it from the Huawei but it is too slow and the provided docements in chainees)
2. Extract it on your external sdcard (format it in fat32). this means that inside dload folder there must be two files namely UPDATE.APP and UPDATE_g.APP
Note: I have tried several times to copy the extracted file to internal memory (emmc) via adb push command but it fail due to the large file of UPDATE_g.APP (375MB) therefore use any external SD
3. Put the sdcard in your mobile again and turn it on while pressing three buttons at the sametime vol+, vol- and power button. This is the pink screen mode.
4. The update to the official 2.3.5 (the B512 which can be rooted) should start and your mobile will be rebooted. This step will take about 3 min to complet
5. After finishing turn your mobile on. IDEOX splash secreen will be presented (may take 1 - 2 min) after that android splash secreen will appear.
6. Root your mobile. to root your mobile, you can follow this steps of That-Guy'a thread
http://forum.xda-developers.com/showthread.php?t=1420728
İF you tried to install CM7 or MIUI from the recoverry mode you can get an error
Finding update package...
Opening update package...
Verifying update package...
E:failed to verify whole-file signature
E:verification failed
Installation aborted
Therefore you need to re-copy ClockworkMod v5.5.0.4 (you can use linux to copy the file .cust_backup/image folder while you are in pink mode)
also you can find another version (CWM Recovery 5.0.2.7) on http://forum.xda-developers.com/showthread.php?t=1343276
7. You will now able now to install CM7 or MIUI.
special thanks to That-Guy and matteof93
Hello Friends
I myself purchased this cool phone with some serious hardware, and so you'll agree that this phone doesn't deserve a gingerbread. Thankfully, Huawei came out with the official ICS and it is now available for download here
I tried to find a proper tutorial to update to ICS but was facing a problem with the standard method, placing the app in the dload folder of the root sd card, shutting the phone down, removing the battery and then vol+/vol-/Power method.
I however found out an easier method to update, which is explained as below. Note that my phone is working fine, without any hiccups whatsoever.
Also note that I was on official GB 2.3.5, which can be downloaded from here, and installed using the same steps as below. I recommend to be on the latest GB firmware, although I'm not sure if that's the necessary condition.
Another thing is, I tried the below steps and was able to successfully update my phone. Whatever you do is at your own risk. This is a fairly simple and harmless method, but Murphy's Law applies everywhere
Backing up your data is, as usual, recommended.
Steps:
1.Download the ICS update from the link given above.
2. Extract the file. There are 3 folders named step 1, step 2, step 3, each having a folder named dload and each having a update.app file.
3.Open Step 1 and copy the dload folder and paste it in the root directory of the sd card. If you're confused which is the root directory, check this article out. http://uk.answers.yahoo.com/question/index?qid=20120315022047AAEuZhU
4. Turn off the USB storage.
5.Breathe
6.Go to settings - storage - Software Upgrade - Choose from SD Card.
7.Make sure you have charged your phone sufficiently. and confirm
8. The procedure should take some time, do not panic, and the phone will restart after a while. If it shows 'OK Done' but does not restart, pull out the battery and start the phone normally.
9.Connect the phone to the computer via mount USB Storage again, delete the dload folder. Go to the folder where you extracted the downloaded ICS update file, open Step 2. Copy the dload folder and paste in the root directory of the SD card as before.
10. Repeat the same procedure, as Step 5 and Step 6
11. This step should take a bit longer, so dont panic.
12. After it is successful, the android robot will appear, asking you to sign in and all. You might think this is it, but the procedure is not yet complete. I encountered some bugs here, like force closing of some apps. Hence, the Step 3 update file is important.
13. Again, connect the phone to the computer, mount usb storage, and repeat step 9. Only this time, copy the dload folder of Step 3 and paste in the root directory.
14. Repeat step 6.
15.I didnt get an automatic restart this time, so I pulled the battery out after getting a 'OK message' and put it back in booted the phone. And here you get the official ICS with a taste of Huawei
Sign in, and enjoy.
You can also root your phone for Superuser access, with the help of this article : (Check the root section) http://forum.xda-developers.com/showthread.php?t=1736650
I'm new here, so if I did anything wrong please feel free to comment or correct me. Thanks!
ameypv said:
Hello Friends
I myself purchased this cool phone with some serious hardware, and so you'll agree that this phone doesn't deserve a gingerbread. Thankfully, Huawei came out with the official ICS and it is now available for download here
I tried to find a proper tutorial to update to ICS but was facing a problem with the standard method, placing the app in the dload folder of the root sd card, shutting the phone down, removing the battery and then vol+/vol-/Power method.
I however found out an easier method to update, which is explained as below. Note that my phone is working fine, without any hiccups whatsoever.
Also note that I was on official GB 2.3.5, which can be downloaded from here, and installed using the same steps as below. I recommend to be on the latest GB firmware, although I'm not sure if that's the necessary condition.
Another thing is, I tried the below steps and was able to successfully update my phone. Whatever you do is at your own risk. This is a fairly simple and harmless method, but Murphy's Law applies everywhere
Backing up your data is, as usual, recommended.
Steps:
1.Download the ICS update from the link given above.
2. Extract the file. There are 3 folders named step 1, step 2, step 3, each having a folder named dload and each having a update.app file.
3.Open Step 1 and copy the dload folder and paste it in the root directory of the sd card. If you're confused which is the root directory, check this article out. http://uk.answers.yahoo.com/question/index?qid=20120315022047AAEuZhU
4. Turn off the USB storage.
5.Breathe
6.Go to settings - storage - Software Upgrade - Choose from SD Card.
7.Make sure you have charged your phone sufficiently. and confirm
8. The procedure should take some time, do not panic, and the phone will restart after a while. If it shows 'OK Done' but does not restart, pull out the battery and start the phone normally.
9.Connect the phone to the computer via mount USB Storage again, delete the dload folder. Go to the folder where you extracted the downloaded ICS update file, open Step 2. Copy the dload folder and paste in the root directory of the SD card as before.
10. Repeat the same procedure, as Step 5 and Step 6
11. This step should take a bit longer, so dont panic.
12. After it is successful, the android robot will appear, asking you to sign in and all. You might think this is it, but the procedure is not yet complete. I encountered some bugs here, like force closing of some apps. Hence, the Step 3 update file is important.
13. Again, connect the phone to the computer, mount usb storage, and repeat step 9. Only this time, copy the dload folder of Step 3 and paste in the root directory.
14. Repeat step 6.
15.I didnt get an automatic restart this time, so I pulled the battery out after getting a 'OK message' and put it back in booted the phone. And here you get the official ICS with a taste of Huawei
Sign in, and enjoy.
You can also root your phone for Superuser access, with the help of this article : (Check the root section) http://forum.xda-developers.com/showthread.php?t=1736650
I'm new here, so if I did anything wrong please feel free to comment or correct me. Thanks!
Click to expand...
Click to collapse
Ya we all know. Almost everyone does it this way.
Generation_Next-2000 said:
Ya we all know. Almost everyone does it this way.
Click to expand...
Click to collapse
Yep, but thought this would help many users who would struggle with the other method.
Im curious to know how you posted in the dev section with under 10 posts...
Somcom3X said:
Im curious to know how you posted in the dev section with under 10 posts...
Click to expand...
Click to collapse
As I said I have no idea where to post this.
This is for u8800 PRO not the u8800. I really hope X5 U8800 non pro users don't follow your advice.
I guess this thread needs to be moved to U8800 pro section...
It was posted in the u8800 section before the mods moved it here.
I am having Honor 7 from UAE with build number PLK-L01C185B120. How do i update to latest build B320 or B330? which ever is stable and official one.
Phone was previously only updated once by updater from which version I didn't notice. So how do I go about updating? downgrade first?
Pl note the steps below
1. Go to Settings -> about phone -> android versions
2. Check for compatibility of downloaded firmware (check attached compatibility note by honor (refer attached note)
Procedure:-
There are two methods to upgrade: normal upgrade and force upgrade.
Normal upgrade needs to start the handset and enter the System Update module. Force upgrade is just used when the handset can’t boot up or can’t enter the idle screen.
Note: While upgrading SD version do not connect to the PC through USB.
A) Forced Upgrade operations
B) Normal upgrade
Step 1. Format the Micro SD card (This operation is optional).
Step 2. Copy the Software: main package UPDATE.APP to a directory named dload.
Step 3. Copy the entire dload folder (with UPDATE.APP in it) to the root directory of the Micro SD card.
Step 4. Insert the Micro SD card into the handset and power on. After entering the home screen, To find System Update application, press Dialer->press *#*#2846579#*#*->select Software Upgrade->select SDCard Upgrade-> ok to start the upgrade.
Force upgrade
Step 1. Format the Micro SD card (This operation is optional).
Step 2. Copy the Software: main package to a directory named dload.
Step 3. Copy the entire dload folder (with UPDATE.APP in it) to the root directory of the Micro SD card.
Step 4. Make sure your handset is power off. Insert the Micro SD card into the handset. Press the VOLUME UP and VOLUME DOWN key, and then press the POWER key to power on the phone and enter the Software Upgrade Mode.
Step 5. When the progress bar stop, the phone will restart automatically
---------- Post added at 08:49 PM ---------- Previous post was at 08:46 PM ----------
rspn69 said:
Pl note the steps below
1. Go to Settings -> about phone -> android versions
2. Check for compatibility of downloaded firmware (check attached compatibility note by honor (refer attached note)
Procedure:-
There are two methods to upgrade: normal upgrade and force upgrade.
Normal upgrade needs to start the handset and enter the System Update module. Force upgrade is just used when the handset can’t boot up or can’t enter the idle screen.
Note: While upgrading SD version do not connect to the PC through USB.
A) Forced Upgrade operations
B) Normal upgrade
Step 1. Format the Micro SD card (This operation is optional).
Step 2. Copy the Software: main package UPDATE.APP to a directory named dload.
Step 3. Copy the entire dload folder (with UPDATE.APP in it) to the root directory of the Micro SD card.
Step 4. Insert the Micro SD card into the handset and power on. After entering the home screen, To find System Update application, press Dialer->press *#*#2846579#*#*->select Software Upgrade->select SDCard Upgrade-> ok to start the upgrade.
Force upgrade
Step 1. Format the Micro SD card (This operation is optional).
Step 2. Copy the Software: main package to a directory named dload.
Step 3. Copy the entire dload folder (with UPDATE.APP in it) to the root directory of the Micro SD card.
Step 4. Make sure your handset is power off. Insert the Micro SD card into the handset. Press the VOLUME UP and VOLUME DOWN key, and then press the POWER key to power on the phone and enter the Software Upgrade Mode.
Step 5. When the progress bar stop, the phone will restart automatically
Click to expand...
Click to collapse
Attachment for compatibility check
OK very nice, thanks for the help, I can follow that, but
1. where do I find UPDATE.APP?
2. Since I am on B120 version which firmware version should I download for update?
3. This is UAE model phone, Is downloading any B320 or B330 firmware can work for L01 model?
Note: phone default updater is not showing anything to be updated.
rspn69 said:
Pl note the steps below
1. Go to Settings -> about phone -> android versions
2. Check for compatibility of downloaded firmware (check attached compatibility note by honor (refer attached note)
Procedure:-
There are two methods to upgrade: normal upgrade and force upgrade.
Normal upgrade needs to start the handset and enter the System Update module. Force upgrade is just used when the handset can’t boot up or can’t enter the idle screen.
Note: While upgrading SD version do not connect to the PC through USB.
A) Forced Upgrade operations
B) Normal upgrade
Step 1. Format the Micro SD card (This operation is optional).
Step 2. Copy the Software: main package UPDATE.APP to a directory named dload.
Step 3. Copy the entire dload folder (with UPDATE.APP in it) to the root directory of the Micro SD card.
Step 4. Insert the Micro SD card into the handset and power on. After entering the home screen, To find System Update application, press Dialer->press *#*#2846579#*#*->select Software Upgrade->select SDCard Upgrade-> ok to start the upgrade.
Force upgrade
Step 1. Format the Micro SD card (This operation is optional).
Step 2. Copy the Software: main package to a directory named dload.
Step 3. Copy the entire dload folder (with UPDATE.APP in it) to the root directory of the Micro SD card.
Step 4. Make sure your handset is power off. Insert the Micro SD card into the handset. Press the VOLUME UP and VOLUME DOWN key, and then press the POWER key to power on the phone and enter the Software Upgrade Mode.
Step 5. When the progress bar stop, the phone will restart automatically
---------- Post added at 08:49 PM ---------- Previous post was at 08:46 PM ----------
Attachment for compatibility check
Click to expand...
Click to collapse
abdulkha said:
OK very nice, thanks for the help, I can follow that, but
1. where do I find UPDATE.APP?
2. Since I am on B120 version which firmware version should I download for update?
3. This is UAE model phone, Is downloading any B320 or B330 firmware can work for L01 model?
Note: phone default updater is not showing anything to be updated.
Click to expand...
Click to collapse
1. UPDATE.APP can be found in downloaded firmware by extracting.
2. B330 version is not suitable for LA model and that's why I mentioned earlier to check the compatibility of firmware . When you download and extract the firmware, you will find three files. 1) updater.app, 2. compatibility declaration and third about open source declaration.
3. Default updater hardly works for someone. So don't worry about that.
4. Its better to throw money in downloading firmware (data charges) but do not flash uncompatible rom and brick the mobile
---------- Post added at 06:58 AM ---------- Previous post was at 06:26 AM ----------
Download b320 version and check whether compatible with your region and version b120
rspn69 said:
1. UPDATE.APP can be found in downloaded firmware by extracting.
2. B330 version is not suitable for LA model and that's why I mentioned earlier to check the compatibility of firmware . When you download and extract the firmware, you will find three files. 1) updater.app, 2. compatibility declaration and third about open source declaration.
3. Default updater hardly works for someone. So don't worry about that.
4. Its better to throw money in downloading firmware (data charges) but do not flash uncompatible rom and brick the mobile
---------- Post added at 06:58 AM ---------- Previous post was at 06:26 AM ----------
Download b320 version and check whether compatible with your region and version b120
Click to expand...
Click to collapse
So far I have tried two roms b121 and b320 both are for the region of C432 (EU i guess) and result in failure immediately as soon as the process of update start. Both roms are not compatible for b120 but i tried anyway.
so now my question is how to change my region c185b120 to c432b121 so i can use b320 firmware to update?
btw I have unlocked the bootloader using multitool but still no change in failure.
Change region by debranding option found in honor 7 multi tool just follow the procedures there flash stock recovery of b100 and use the force update method mentioned to flash the whole rom of c432b100 after downloading it it will erase your data then you will recieve b121 upadate after ota you can update manually to b180 after that and you are good to go
I was on c185b120 now iam on c432b180 waiting the mm
---------- Post added at 04:28 AM ---------- Previous post was at 04:17 AM ----------
The mentioned options you will find in multitool debranding ..flashing stock recovery
if force update failed after flashing stock recovery use the method you already used and failed with you with the rom c432b100 and it wont fail isa as it becomes compatible just follow instructions in multitool and becareful
Hi all! After sarchin' on the net (and haven't found anything good), I'll make a guide on How to unroot, unbrick 'n' lock your device.
BEFORE ALL
There is one problem: The rollbacks don't exist for all models, so this guide isn't for everything models. I don't recommend to use it for India, China, Middle East regions' versions.
You can find everything needed for you
HERE for the FRD-L09
HERE for the FRD-L04 (thanks to @matt914)
TESTED DEVICES
FRD-L09 (By me)
FRD-L04 (By @matt914 again)
Code:
/*
* I am not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this GUIDE
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at me for messing up your device, I will laugh at you.
*/
WHAT YOU NEED
1. Your device (that guide is only for Honor 8)
2. Your rollback and MM packages WATCH HERE
3. A MicroSD card and its MicroSD/SD or MicroSD/USB reader
4. Your PC (I've tested it with linux, but You can use Windows too).
5. Your USB cable
HOW TO
1. Download the rollback and the MM firmware from hihonor
2. Extract the zip packages, you'll find a dload folder and some pdfs (you can delete these pdfs)
FOR LINUX
3. Before all install the android-tools (google is your friend on that)
4. With THAT you'll be able to extract files from MM UPDATE.APP (thanks to @marco.minetti), you'll find lots of .img files, but we need BOOT.img and RECOVERY.img
5a. reboot your phone to fastboot (Vol-/Power while plug it to your PC)
5b. Open a terminal on the folder where you have the previous 2 files and type:
Code:
sudo fastboot flash boot BOOT.img
sudo fastboot flash recovery RECOVERY.img
sudo fastboot reboot
6a. Your device now is semi-bricked (it can reboot to erecovery and to fastboot but it can't boot)
6b. Shut down your device (long press Power, it will reboot. Press vol+ while asked and boot to erecovery, than shutdown)
7a. Put your rollback's dload folder on the root of the MicroSD (NOT THE INTERNAL MEMORY!)(Use a MicroSD reader)
7b. Insert the MicroSD on your Honor
8. Press Vol+/Vol-/Power and it will start flashing the rollback
9. Your device still in a semi-bricked condition
10. Make passage 7 and 8 again with the MM firmware
11. Now it will boot up without any problem and with MM installed
FOR WINDOWS
3. Before all install the minimal android tool (google is your friend on that)
4. With Huawei Extractor tool, you'll find lots of .img files, but we need BOOT.img and RECOVERY.img (FROM THE MM UPDATE.APP)
5a. reboot your phone to fastboot (Vol-/Power while plug it to your PC)
5b. Open a CMD (with administrator access) on the folder where you have the previous 2 files and type:
Code:
fastboot flash boot BOOT.img
fastboot flash recovery RECOVERY.img
fastboot reboot
6a. Your device now is semi-bricked (it can reboot to erecovery and to fastboot but it can't boot)
6b. Shut down your device (long press Power, it will reboot. Press vol+ while asked and boot to erecovery, than shutdown)
7a. Put your rollback's dload folder on the root of the MicroSD (NOT THE INTERNAL MEMORY!)(Use a MicroSD reader)
7b. Insert the MicroSD on your Honor
8. Press Vol+/Vol-/Power and it will start flashing the rollback
9. Your device still in a semi-bricked condition
10. Make passage 7 and 8 again with the MM firmware
11. Now it will boot up without any problem and with MM installed
AT THE END
If you have followed the instructions correctly you'll with a device with MM firmware. It will download b380 and than b389 (for the FRD-L09 version).
Flashing the MM package will lock your device (not relock) so you don't need the fastboot oem lock [key]
Great Guide. if you provide direct links for rollback , it would be more easy
venugopalu007 said:
Great Guide. if you provide direct links for rollback , it would be more easy
Click to expand...
Click to collapse
I'm sorry but every device model have their rollback files so it will really long to make
Without p.c just download the both zips and dload one after another.
FRD-LO9 :: http://www.hihonor.com/uk/support/details/index.html?DOC_ID=92131 (73 MB link)
http://www.hihonor.com/uk/support/details/index.html?DOC_ID=92101 (1.75GB link )
venugopalu007 said:
Without p.c just download the both zips and dload one after another.
FRD-LO9 :: http://www.hihonor.com/uk/support/details/index.html?DOC_ID=92131 (73 MB link)
http://www.hihonor.com/uk/support/details/index.html?DOC_ID=92101 (1.75GB link )
Click to expand...
Click to collapse
That's guide is for unbrick the device
ScardracS said:
That's guide is for unbrick the device
Click to expand...
Click to collapse
But in offical site they said rollback form nougat to mm
venugopalu007 said:
But in offical site they said rollback form nougat to mm
Click to expand...
Click to collapse
And unbrick the device
Rommco05 said:
Hi, good guide. Here is one problem, don't exist rollbacks for all models, I think is only for EU and US. In some situations can rollback US/EU make a problems. I realy don't recommend to use for India, China, Middle East regions. But for EU and US models it is uselful. If u want maybe is good idea update OP
Click to expand...
Click to collapse
Thank man! I've Just edited it but I don't think the rollback package is needed to make the unbrick
ScardracS said:
Thank man! I've Just edited it but I don't think the rollback package is needed to make the unbrick
Click to expand...
Click to collapse
The rollback package definitely doesn't contain a file named BOOT.img. This file is only available in the firmware package.
kayro_ said:
The rollback package definitely doesn't contain a file named BOOT.img. This file is only available in the firmware package.
Click to expand...
Click to collapse
I've corrected the OP
ScardracS said:
I've corrected the OP
Click to expand...
Click to collapse
Within the LINUX guide there is still point 4.:
With THAT you'll be able to extract files from ROLLBACK UPDATE.APP (thanks to @marco.minetti), you'll find lots of .img files, but we need BOOT.img and RECOVERY.img
Click to expand...
Click to collapse
kayro_ said:
Within the LINUX guide there is still point 4.:
Click to expand...
Click to collapse
IMPORTANT: If you can't find the file BOOT.img inside the rollback package -> it's just under a different name called EFI.img.
kayro_ said:
IMPORTANT: If you can't find the file BOOT.img inside the rollback package -> it's just under a different name called EFI.img.
Click to expand...
Click to collapse
No, I've edited the post. You have to use the 2 from mm package
For step 7 in the Windows guide, how exactly are we supposed to put the rollback dload folder onto the SD card when it wont mount the SD card? twrp? or do I have to take out the SD card and use it in a card reader?
edit: Thought I should add that when I go into Windows Device Manager, right click Honor 8, and choose browse files -> ( H: ), it says "Please insert a disc into CD Drive H: "
matt914 said:
For step 7 in the Windows guide, how exactly are we supposed to put the rollback dload folder onto the SD card when it wont mount the SD card? twrp? or do I have to take out the SD card and use it in a card reader?
edit: Thought I should add that when I go into Windows Device Manager, right click Honor 8, and choose browse files -> ( H: ), it says "Please insert a disc into CD Drive H: "
Click to expand...
Click to collapse
You have to use a MicroSD card reader
ScardracS said:
You have to use a MicroSD card reader
Click to expand...
Click to collapse
I had to go through a round-a-bout method with using my old Xperia Z as the SD card reader, but it worked out in the end. Thank you so much! Thanked you in the original post!
matt914 said:
I had to go through a round-a-bout method with using my old Xperia Z as the SD card reader, but it worked out in the end. Thank you so much! Thanked you in the original post!
Click to expand...
Click to collapse
I'm really happy I could try to help you and other guys here
Here are the FRD-L04 files for the unbrick. Firmware on this MM is B122
MEGA link
Thanks for this man. I'll try this out before I sell my Honor 8.
---------- Post added at 04:28 PM ---------- Previous post was at 04:26 PM ----------
matt914 said:
Here are the FRD-L04 files for the unbrick. Firmware on this MM is B122
MEGA link
Click to expand...
Click to collapse
Hey man can you mirror this to Drive?
Oh bro they are from b122. u can extract them if u had b122 update.app
My P10 plus is rooted, Normally i can't get system update, so I try to update manually my Android system from nougat (vky-L09c432b150) to Oreo (8.0.0.360) international update, I try it by 2 methods normal update via TWRP and by forcing update by extracting update. App to dload folder on SD card and reboot in erecovery mode to auto start the update process, but unsuccessfully. So guys, what is the good method to execute any new update.?
http://www.stechguide.com/huawei-p10-plus-b360-oreo-firmware-update/
oreo update incomplete
I try to update the system 2 times, 1-from the sdcard 2-i changed to local c:/ in my pc where i put the HOWTA folder
i follow the full steps but when i reach the last one, this phrase "Please wait for upload files and do not press any key." take more than 20 minutes and nothing happend!!
Plez tell me if there any further tricks to do for to succes this process.
Don't need sdcard please copy threes files to HWOTA/Update folder on your PC, type 2
Gamkutopolowk said:
Don't need sdcard please copy threes files to HWOTA/Update folder on your PC, type 2
Click to expand...
Click to collapse
In the guide, Method 2,
3) Now download all three update, data, and public files (make sure you rename the files as mentioned above) and copy them either in the external SDCard inside HWOTA folder or in the PC in the C:\..\HWOTA\update folder.
4) Run the update.bat file as an administrator, It will ask you if you copied the files. Press any key to continue.
Click to expand...
Click to collapse
1. if I copy the 3 files in SD Card, do I put it in /SDCard/HWOTA or /SDCard/HWOTA/Update ? Why the folders are different in sdcard or pc?
2. If I have all the files copied in the SD card, do I run the script directly from the SD card? or I have to put it somewhere on the pc and run it as admin?
- 2. I tried running the update.bat from pc and it works.
https://www.youtube.com/watch?v=49AY0MboxuE
Gamkutopolowk said:
Don't need sdcard please copy threes files to HWOTA/Update folder on your PC, type 2
Click to expand...
Click to collapse
Hello,
Please advise hot to update my Huawei P10 Plus VKY-L09CO2B102 to OREO.
Currently Stock Rooted EMUI 5.1 - Android 7.0 - TWRP 3.1.0-0 - root Superuser Koushik.
Did not update since purchase in June 2017. No security updates as well. I deactivated the updater.
Now I would like to update to OREO, update TWRP, and root.
I have TWRP - is it not possible to copy files to SD card and update?
...
https://forum.xda-developers.com/p10-plus/how-to/huawei-p10-plus-debrand-rebrand-update-t3715288