pleas help - Galaxy Note 3 Q&A, Help & Troubleshooting

I have a problem I wanted to install a new recovery twrp 08/02/70 . but I could not get the bootlop then I Odin flash stock lolipop 5.0 but now I can not install recovery still write me in stock recovery E : failed to mount / EFS ( invalid argument )

Did flash the stock rom with a pit file?

I install stock rom and naw rot and phisl touch recovery but a cen instal rom music of life v4 6.0.1 rom
pleas help whit install rom
What should I do now I have a model n9005 new bootloader BL_N9005XXUGBPB2_BOOTLOADER.tar.md5 and modem installed CP_N9005XXUGBPB1_MODEM.tar.md5 I philz_touch_6.48.4 - hlte.tar.md5
Install follows wipedata / factory reset and then a new clean room then wipe cache partition and wipe Dalvik cache and then install rom choose the option note 3 n9005 international CSC then choose default
then do not wipe keep apps and that's it you set the phone starts up and appears with a logo and a blue light and regulations Bit Set Warranty : kernel and nothing happens that I leave to stand for half an hour , or who knows what I'm doing wrong pleas help whit this.

Sorry wrong thread

audit13 said:
Did flash the stock rom with a pit file?
Click to expand...
Click to collapse
To flash TWRP Recovery:
1. Turn off phone
2. Bring the phone to Download Mode (power button + vol up + home)
3. Connect phone to computer and open up Odin
4. Click on AP or PDA and select your .tar file (this is the twrp recovery file)
5. Click Start and once done your phone will reboot into TWRP
If your phone does not boot into TWRP automatically:
a) repeat steps 1-4
b) click on options tab (in Odin) and uncheck everything except "F. Reset Time"
c) click Start
d) once done, disconnect your phone and take out your battery
e) bring the phone to Download Mode (power button + vol up + home)
f) your phone should then boot into TWRP
For more detailed instructions: http://forum.xda-developers.com/showthread.php?t=2560928
Good luck!

M-Ego said:
To flash TWRP Recovery:
1. Turn off phone
2. Bring the phone to Download Mode (power button + vol up + home)
3. Connect phone to computer and open up Odin
4. Click on AP or PDA and select your .tar file (this is the twrp recovery file)
5. Click Start and once done your phone will reboot into TWRP
If your phone does not boot into TWRP automatically:
a) repeat steps 1-4
b) click on options tab (in Odin) and uncheck everything except "F. Reset Time"
c) click Start
d) once done, disconnect your phone and take out your battery
e) bring the phone to Download Mode (power button + vol up + home)
f) your phone should then boot into TWRP
For more detailed instructions: http://forum.xda-developers.com/showthread.php?t=2560928
Good luck!
Click to expand...
Click to collapse
Thanks hope it helped

Related

Official Stock Roms - Links and full guide (Full Clean install Guide Included)

Hi XDAers, am new to sharing, and wanted to start with this thread as it might be helpful for many people
Am not responsible if you bricked your phone, so don't blame me!
Lets start with the guide:
What u need:
1- Samsung drivers Here
2- Odin flasher Here
3- Rom files which u will find Here
4- (Optional) To do a full clean install or to root your rom u will need Philz kernel
Installation Steps:
1-Install the previously downloaded samsung drivers on your PC
2-Start your phone in download mode (while the phone is off press and hold PWR button + Vol dwn + Home)
3-Start Odin (above link)
4-Click on the PDA Btn and select the rom file you downloaded (.tar file)
5-Connect your phone (don't use any usb hub or whatever,etc.) so that the phone is connected directly to the PC
6-Wait until you see the upper left box in odin turns yellow
7-Click on start and don't touch anything until its all done
Congratulations! now u have a stock rom installed on your phone
To have a Full clean install (u have to do this first) :
1- Go to Philz kernel and download the one that corresponds to your current firmware build code
(you can know your current rom code by going to settings, about device, the 5 letters after i9100 in Build number are your firmware code)
2- Place the zip you downloaded on your external sd card
3- Start the device in recovery mode (while the phone is off press and hold PWR + HOME + VOL UP)
4- Scroll to install update from external storage using the volume keys and power btn for selection
5- Go to the kernel you downloaded and install it.
6-Turn off ur phone and start again in recovery mode, it will start the newly installed recovery
7- Now go to mounts and storage and format (system,preload,data,cache), Go back to main menu, Select advanced and wipe Dalvik cache
Now ur phone is fully cleaned and ready for Installation !!
For rooting after installation, Repeat the previous steps until step 5
:highfive:
Credits :
Thanks to Sammobile.com/ for the ROMs
Thanks to Phil3759 for his great work
Press Thanks if I helped :good:​

(guide) easiest way to flash clockworkmod touch recovery

Note: works only on GT-i8190
Software needed:
Odin v 3.07 ( http://forum.xda-developers.com/attachment.php?attachmentid=1168421&d=1341114315 )
Cwm touch recovery file ( http://www.androidfilehost.com/?fid=9390334956548391158 )
Note: please use only the link given above for Cwm touch recovery file
DO THIS AT YOUR OWN RISK
How to:
1) open Odin in your computer
2) select PDA and
3) check if only auto reboot and F.reset time checkboxes are selected
4) put your phone on download mode (shut down the phone then press volume down key + power key + home key)
5) a warning will appear then press volume up key
6) connect your phone to your computer
7) in the message box it will show added (on Odin)
8) click start
9) then wait till it shows pass
10) unplug your device
11) install rom manager by clockworkmod (optional)
You are finished
I don't think it is possible to root your phone without first install any cwm recovery
This have been possible ever since I made the Odin file.... And you don't need root to use Odin.
Sent through time and space from my s3mini/CM10.1

Can't enter recovery..stuck on Samsung Logo (4.3)

hey guys, i hope someone can help me with this problem.
Problem:
1. flashed cobra ROM coming from Crash (4.3). Wiped EVERYTHING as instructed & reboot.
2. phone stuck in bootloop for 20 mins ( Samsung logo). So i tried to enter recovery to flash it again.
3. failing to enter recovery CWM 6.0.4.4 by press keys (Power+Vol UP)
>> phone goes blank for a second & then comes back to S4 logo & finally bootloops on Samaung logo
Do I have to flash everything from scratch?
( Odin >> Pit >> Factory image >> Custom recovery )
re: pit file
prabhjeet.oberoi said:
hey guys, i hope someone can help me with this problem.
Problem:
1. flashed cobra ROM coming from Crash (4.3). Wiped EVERYTHING as instructed & reboot.
2. phone stuck in bootloop for 20 mins ( Samsung logo). So i tried to enter recovery to flash it again.
3. failing to enter recovery CWM 6.0.4.4 by press keys (Power+Vol UP)
>> phone goes blank for a second & then comes back to S4 logo & finally bootloops on Samaung logo
Do I have to flash everything from scratch?
( Odin >> Pit >> Factory image >> Custom recovery )
Click to expand...
Click to collapse
Odin flash official stock rom but don't flash any PIT files.
The PIT file is the partition information tables and if there
was anything wrong with that file the phone would be dead.
It would be a hard brick and have a blank black screen.
Misterjunky said:
Odin flash official stock rom but don't flash any PIT files.
The PIT file is the partition information tables and if there
was anything wrong with that file the phone would be dead.
It would be a hard brick and have a blank black screen.
Click to expand...
Click to collapse
thanks
downloading the official firmware & will flash the stock ROM
Hope everything goes back to normal.
>> how can i be sure that the PIT isn't already corrupted?
>> why isn't the phone booting into CWM recovery ?
Are you sure that you are holding the Vol up key + home key long enough. For me i have to hold all 3 until i get the i9500 screen then hold vol up and home until i get the recovery load up.
mattjgay said:
Are you sure that you are holding the Vol up key + home key long enough. For me i have to hold all 3 until i get the i9500 screen then hold vol up and home until i get the recovery load up.
Click to expand...
Click to collapse
ok i flashed the stock firmware & am able to boot phone on stock 4.3
PROBLEM:
1. go to Odin
2. flash CWM 6.0.4.4 >> flash successful>>PASS>>RESET
>>The phone STILL refuses to boot into recovery.
when i hold all the 3 buttons (Power+Vol UP+Home), the phone just keeps blinking on the Galaxy S4 Logo.
If I leave the buttons, it does a normal boot.
Q. Is there another method to go into recovery?
Am I missing something Here??
Try a different Odin version. Try 1.85 and make sure auto-reboot is not selected.
FINALLY!!
Lennyz1988 said:
Try a different Odin version. Try 1.85 and make sure auto-reboot is not selected.
Click to expand...
Click to collapse
I re-did the entire procedure & it works.
Followed tutorial on Cobra ROMs page by S.a.M.e.R_d
1. Re-flash pit file>>adonis.pit
2. flash factory firmware>>I9500XXUEMJ9_I9500ODDEMJ5_INU
3. let it boot
4. flash custom recovery through Odin >> GT-I9500-CWM-6.0.4.5
5. Press & hold (Power+vol UP+ home)>> Enter recovery
The procedure was similar to what i had done earlier, except for flashing the pit file again.
Did the Trick.
Running >> KingCobra_Build_3_GT-I9500 :good::fingers-crossed:

[Q] (i9500) I flashed the leak of Lollipop and can't initiate in recovery mode

Hi, I flashed this monday the leak of Lollipop for Samsung Galaxy S4 (9500) and after I followed all the steps one by one I'm the only one in earth that isn't able to start the phone in the recovery mode. For this reason I can't flash gapps. I am not able to downgrade even because for the KNOX.
Someone has the same problem? Can anyone figured out how to enter in recovery mode?
P.D: I have attempted to do it with the buttons (vol down + pow + home) and with adb and the usb connected to the phone. Anyone was the solution.
masicen said:
Hi, I flashed this monday the leak of Lollipop for Samsung Galaxy S4 (9500) and after I followed all the steps one by one I'm the only one in earth that isn't able to start the phone in the recovery mode. For this reason I can't flash gapps. I am not able to downgrade even because for the KNOX.
Someone has the same problem? Can anyone figured out how to enter in recovery mode?
P.D: I have attempted to do it with the buttons (vol down + pow + home) and with adb and the usb connected to the phone. Anyone was the solution.
Click to expand...
Click to collapse
after flashing Rom with Odin you have to flash openrecovery-twrp-2.8.4.0-klte.tar
Installing Recovery and rooting steps :
1- download twrp from here
2- go to flash mode
3- run Odin load file as AP then click start
4- go to recovery by powering off your device and hold volume up + home + power button
5- when you want to reboot to system Twrp will ask you to install SuperSU (rooting your device)
6- swipe to confirm
More info here
haririan said:
after flashing Rom with Odin you have to flash openrecovery-twrp-2.8.4.0-klte.tar
Installing Recovery and rooting steps :
1- download twrp from here
2- go to flash mode
3- run Odin load file as AP then click start
4- go to recovery by powering off your device and hold volume up + home + power button
5- when you want to reboot to system Twrp will ask you to install SuperSU (rooting your device)
6- swipe to confirm
More info here
Click to expand...
Click to collapse
I did all of this, still can't to initiate in recovery mode.
i had the same problem, try downloading philz (philz_touch_6.48.4-i9500) or twrp recovery (openrecovery-twrp-2.8.4.0-i9500) and install via odin (AP box)
I didn't try the above i just installed the rom again, doing this:
- only the AP file
- uncheck "auto reboot"
- After the process finishes dont reboot the phone to tw, just go to the recovery mode and the wipe cache/data
- Install philz or twrp via odin
dnnz said:
i had the same problem, try downloading philz (philz_touch_6.48.4-i9500) or twrp recovery (openrecovery-twrp-2.8.4.0-i9500) and install via odin (AP box)
I didn't try the above i just installed the rom again, doing this:
- only the AP file
- uncheck "auto reboot"
- After the process finishes dont reboot the phone to tw, just go to the recovery mode and the wipe cache/data
- Install philz or twrp via odin
Click to expand...
Click to collapse
So, flash the ROM again with nothing more than the AP box fullfiled and then, when it finishes hold (vol up + power + home). Wipe cache, restart and flash custom recovery.
Am I right?
masicen said:
.........................P.D: I have attempted to do it with the buttons (vol down + pow + home) and with adb and the usb connected to the phone. Anyone was the solution.
Click to expand...
Click to collapse
masicen said:
So, flash the ROM again with nothing more than the AP box fullfiled and then, when it finishes hold (vol up + power + home). Wipe cache, restart and flash custom recovery.
Am I right?
Click to expand...
Click to collapse
It can not, because in the first flash has deleted the modem, bootloader, csc and others, so if flashing only AP will not operate the phone, only the PDA.
And masicen these questions have to do in the same thread firmware also behold the solution.
Flashes the firmware again, to start turn it off and go into Recovery by: Volume Up + Home + Power in this order and holding down until you see the Samsung logo there S4 loose and enter the stock recovery, do wipes and restart it, then download Philz Touch in its latest version and flash it with Odin and restart turn it off and try to enter the recovery now.-
lobomarino said:
It can not, because in the first flash has deleted the modem, bootloader, csc and others, so if flashing only AP will not operate the phone, only the PDA.
And masicen these questions have to do in the same thread firmware also behold the solution.
Flashes the firmware again, to start turn it off and go into Recovery by: Volume Up + Home + Power in this order and holding down until you see the Samsung logo there S4 loose and enter the stock recovery, do wipes and restart it, then download Philz Touch in its latest version and flash it with Odin and restart turn it off and try to enter the recovery now.-
Click to expand...
Click to collapse
Hi, I wasn't able to test it before but now I had my computer and I did all that you suggested and could iniciate in the recovery mode but when I tried to flash gapps an error appeared (status 6) and now I can't manage to flash it :'(
Any solution to that??
p.d: thanks for your help.

[HELP] erorr in CWM or TWRP

hi
i flashed cwm or trwp on my galaxy grand 2
when in press home key+power key+veloum up my phone is going to downloading mod and type "could not normall boot"
what i am doing?!!!:crying::crying::crying:
Please answer ??
Give model of phone ( Lte or dual sim?) and what recovery version u want flash
AiWaNczewski said:
Give model of phone ( Lte or dual sim?) and what recovery version u want flash
Click to expand...
Click to collapse
dual sim
6.0.5 cwm
saeed1378 said:
dual sim
6.0.5 cwm
Click to expand...
Click to collapse
Try flash this : http://forum.xda-developers.com/gal...recovery-twrp-2-8-6-0-touch-recovery-t3107535 , TWRP is much better than CWM and more compatible with new roms AND use ODIN 3.07 Link if u cant find : https://forum.cyanmod.pl/applications/core/interface/file/attachment.php?id=2819
How to install :
1) Install whatever drivers make you happy and make your device connect (i would suggest samsung ones).
2) Reboot your device in download mode you can use adb reboot download or the hardware key combo for your device.
3) Load up Odin and uncheck auto-reboot.
4) Click PDA and select the TWRP tar you downloaded.
5) Connect your device in download mode.
6) Click start.
7) When its finished disconnect your device, pull the battery out.
8) Reinsert the battery and use the hardware keys for your device to power directly into recovery mode (this will bypass install-recovery.sh if you are stock).
9) Enjoy having a custom recovery.
happens with me too
Maybe Because of the bootloader is locked on our devices
AiWaNczewski said:
Try flash this : http://forum.xda-developers.com/gal...recovery-twrp-2-8-6-0-touch-recovery-t3107535 , TWRP is much better than CWM and more compatible with new roms AND use ODIN 3.07 Link if u cant find : https://forum.cyanmod.pl/applications/core/interface/file/attachment.php?id=2819
How to install :
1) Install whatever drivers make you happy and make your device connect (i would suggest samsung ones).
2) Reboot your device in download mode you can use adb reboot download or the hardware key combo for your device.
3) Load up Odin and uncheck auto-reboot.
4) Click PDA and select the TWRP tar you downloaded.
5) Connect your device in download mode.
6) Click start.
7) When its finished disconnect your device, pull the battery out.
8) Reinsert the battery and use the hardware keys for your device to power directly into recovery mode (this will bypass install-recovery.sh if you are stock).
9) Enjoy having a custom recovery.
Click to expand...
Click to collapse
Thank you, the problem was solved.
when im going to recovery boot when i saw logo "galaxy grand 2" i press the volume down and phone went to recovery boot.
saeed1378 said:
Thank you, the problem was solved.
when im going to recovery boot when i saw logo "galaxy grand 2" i press the volume down and phone went to recovery boot.
Click to expand...
Click to collapse
'Nice to know i can help

Categories

Resources