I flashed CM 13 rom with ODIN.without recovery mode .so my phone was hard bricked .it wasn't turned on.so i entered download mode by partitioned SD card method.then i flashed stock firmware .now s3 boot into GALAXY logo and then restart ( i think boot loop ). i can enter to download mode without sd card now.but when i try to enter recovery mode it is jump to download mode and show following :
Could not do normal boot.
ODIN MODE
PRODUCT NAME: GT-I9300I
CURRENT BINARY:CUSTOM
SYSTEM STATUS:CUSTOM
QUALCOMM SECUREBOOT: ENABLE (CSB)
RP SWREV : S1, T1, R1, A1, P1
WRITE PROTECTION: Enable
Related
i sometimes get an 'error' message rebooting my phone (either directly or to/from twrp)
i think it first occured after i flashed twrp
i'm running on cm12 (nightly)
the full text reads:
boot recovery mode
check boot partitions. .
sbl1 partition doesn't exist
odin mode
product name: sm-g900f
current binary: custom
sytem status: custom
reactivation lock(kk): off
knox warranty void: 0x1 (0)
qualcomm secureboot: enable (csb)
rp swrev: s1, t1, r1, a1, p1
secure download : enable
udc start
if i then press the power button for ten seconds, the system boots without a problem
still, i don't like this
i tried solving this problem by going back to stock
also flashed the pit file for my device (g900f)
didn't help
what's wrong and what should i do?
scienex said:
i sometimes get an 'error' message rebooting my phone (either directly or to/from twrp)
i think it first occured after i flashed twrp
i'm running on cm12 (nightly)
the full text reads:
boot recovery mode
check boot partitions. .
sbl1 partition doesn't exist
odin mode
product name: sm-g900f
current binary: custom
sytem status: custom
reactivation lock(kk): off
knox warranty void: 0x1 (0)
qualcomm secureboot: enable (csb)
rp swrev: s1, t1, r1, a1, p1
secure download : enable
udc start
if i then press the power button for ten seconds, the system boots without a problem
still, i don't like this
i tried solving this problem by going back to stock
also flashed the pit file for my device (g900f)
didn't help
what's wrong and what should i do?
Click to expand...
Click to collapse
Could be an emmc failure.. But I'm sorry to be late to the post
thnx mate!
it's four phones ago
but i appreciate your reply :good:
scienex said:
thnx mate!
it's four phones ago
but i appreciate your reply :good:
Click to expand...
Click to collapse
Absolutely boss!
Hi. Samsung Galaxy S4 GT-i9506. Tried to root/install Lollipop 5.0.1 (I had 4.2.2 KitKat).
So everything failed miserably. As it stands now, I can ONLY enter download mode with the phone and in ODIN MODE. I can connect phone to PC and use odin on PC. Can NOT enter recovery mode, it fails and shuts down the device. Only download mode through vol.down+home+power button.
I just want to be able to use my phone, so can someone explain step-by-step what I need to do to get my phone working again? Full reset or anything like that doesn't matter, I have backup, I just want the phone to work again.
It says on the screen (Downloading... Do not turn off target!!) with an android logo.
Could not do normal boot.
ODIN MODE
PRODUCT NAME: GT-I9506
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x1
QUALCOM SECUREBOOT: ENABLE
RP SWREV: S1, T1, R1, A1, P1
WAITE PROTECTION: Enable
UDC START
I have Odin+3.09.
Hi, I have an S3 Neo with CyanogenMod 5.1.1, yesterday I tried to reset it via your phone's settings, it turned on again with a screen depicting the little man Android and the inscription: "Downloading ... Do not turn off target !! ". There is no way to turn it on no 'otherwise, aid
P.S. above are the following messages:
I could not do normal boot
ODIN MODE
PRODUCT NAME: GT-193001
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
QUALCOMM SECURE BOOT: ENABLE (CSB)
RP SWREV: S1, T1, R1, A1, P1
UDC START
Remove the battery and go in recovery mode ( power+vol up + home button)
Flash again your rom after wipes
P.S. do you have enabled f2fs?
So long story short, I screwed up and tried to install TWRP on my Verizon GS5. I realize now that you need to install Safestrap on the Verizon GS5 and that TWRP doesn't work.
The phone is now stuck trying to boot into recovery mode and failing.
When trying to boot, the first screen says:
Code:
RECOVERY BOOTING
SYS REV CHECK FAIL: No version
SECURE: SECURE VERSION failure (recovery.img)
The second screen is the yellow triangle telling me that "System software not authorized by Verizon..."
Code:
SECURE FAIL: RECOVERY
When I put it into download mode it says:
Code:
ODIN MODE
PRODUCT NAME: SM-G900V
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
REACTIVATION LOCK(KK): OFF
QUALCOMM SECUREBOOT: ENABLE (CSB)
RP SWREV: S1, T1, R1, A1, P1
UDC START
Is there any way to fix this? Do I need to use Odin to put a new firmware on the phone?
I can boot into download and recovery mode, but any time I attempt to boot into system I am met with this string of text on the top left:
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-J327P
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
FRP LOCK: OFF
WARRANTY VOID: 0x1 (0x30c)
QUALCOMM SECUREBOT: ENABLE (CSB)
RP SWREV: S1, T1, R1, A1, P1
RP SWREV: K 0, S 0
SECURE DOWNLOAD: ENABLE
Can't get fdt
download mode ! !
This occurred after I was attempting to uninstall SuperSU and replace it with Magisk. Since then I have attempted to factory reset, to no avail. I cannot continue past this screen. Help please!
Shadeofdoom said:
I can boot into download and recovery mode, but any time I attempt to boot into system I am met with this string of text on the top left:
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-J327P
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
FRP LOCK: OFF
WARRANTY VOID: 0x1 (0x30c)
QUALCOMM SECUREBOT: ENABLE (CSB)
RP SWREV: S1, T1, R1, A1, P1
RP SWREV: K 0, S 0
SECURE DOWNLOAD: ENABLE
Can't get fdt
download mode ! !
This occurred after I was attempting to uninstall SuperSU and replace it with Magisk. Since then I have attempted to factory reset, to no avail. I cannot continue past this screen. Help please!
Click to expand...
Click to collapse
Same here but I get the error you are leaving out for recovery.img also. Plus, my USB port is fried. Returns all 0000s for hardware IDs, 3 different cords, 3 machines. At least you have a chance to use recovery. I am totally ****ed.
So, that is ODIN/Download mode. I was high and trying to turn off debugging and switching my USB mode to charge only then doing the whole switch to Modem then back to AP and restart to fix the USB connection with my computer.
Know what I flipped? I'm pretty sure you did the same. I accidentally hit the OEM Unlock switch, turning it off, meaning I enabled OEM Lock. The error when you do a normal boot, not download mode (cuz thats what you posted) is "Custom binary blocked by FRP Lock" (boot.img)". Is your phone stolen or something? That why you left it out?
I got a ton of shady phones from shady mofos who ask me to fix them and then cant pay, but I bought this one new myself and know for sure its not. Releax, it doesn't mean its stolen. IN my case it means drugs are bad and Im dumb.