Hi, I have an S3 Neo with CyanogenMod 5.1.1, yesterday I tried to reset it via your phone's settings, it turned on again with a screen depicting the little man Android and the inscription: "Downloading ... Do not turn off target !! ". There is no way to turn it on no 'otherwise, aid
P.S. above are the following messages:
I could not do normal boot
ODIN MODE
PRODUCT NAME: GT-193001
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
QUALCOMM SECURE BOOT: ENABLE (CSB)
RP SWREV: S1, T1, R1, A1, P1
UDC START
Remove the battery and go in recovery mode ( power+vol up + home button)
Flash again your rom after wipes
P.S. do you have enabled f2fs?
Related
i sometimes get an 'error' message rebooting my phone (either directly or to/from twrp)
i think it first occured after i flashed twrp
i'm running on cm12 (nightly)
the full text reads:
boot recovery mode
check boot partitions. .
sbl1 partition doesn't exist
odin mode
product name: sm-g900f
current binary: custom
sytem status: custom
reactivation lock(kk): off
knox warranty void: 0x1 (0)
qualcomm secureboot: enable (csb)
rp swrev: s1, t1, r1, a1, p1
secure download : enable
udc start
if i then press the power button for ten seconds, the system boots without a problem
still, i don't like this
i tried solving this problem by going back to stock
also flashed the pit file for my device (g900f)
didn't help
what's wrong and what should i do?
scienex said:
i sometimes get an 'error' message rebooting my phone (either directly or to/from twrp)
i think it first occured after i flashed twrp
i'm running on cm12 (nightly)
the full text reads:
boot recovery mode
check boot partitions. .
sbl1 partition doesn't exist
odin mode
product name: sm-g900f
current binary: custom
sytem status: custom
reactivation lock(kk): off
knox warranty void: 0x1 (0)
qualcomm secureboot: enable (csb)
rp swrev: s1, t1, r1, a1, p1
secure download : enable
udc start
if i then press the power button for ten seconds, the system boots without a problem
still, i don't like this
i tried solving this problem by going back to stock
also flashed the pit file for my device (g900f)
didn't help
what's wrong and what should i do?
Click to expand...
Click to collapse
Could be an emmc failure.. But I'm sorry to be late to the post
thnx mate!
it's four phones ago
but i appreciate your reply :good:
scienex said:
thnx mate!
it's four phones ago
but i appreciate your reply :good:
Click to expand...
Click to collapse
Absolutely boss!
Dear In the attempt to install the custom android rom rom 7.1 in my tablet 4 10.1 from samsung model SM-T531 always at the end of the installation the boot does not take place, giving the following message: could not do normal boot. Odin Mode Product name: SM-T531. Current binary: custom knox warranty void: 0x1 (4) Qualcomm secure Boot: Enable (csb) Append: S1, T1, R1, A1, P1 UDC START The tablet goes into download mode. Please how do i solve this problem. Note: Installation is done by TWRP. Thank you
sidiobraz said:
Dear In the attempt to install the custom android rom rom 7.1 in my tablet 4 10.1 from samsung model SM-T531 always at the end of the installation the boot does not take place, giving the following message: could not do normal boot. Odin Mode Product name: SM-T531. Current binary: custom knox warranty void: 0x1 (4) Qualcomm secure Boot: Enable (csb) Append: S1, T1, R1, A1, P1 UDC START The tablet goes into download mode. Please how do i solve this problem. Note: Installation is done by TWRP. Thank you
Click to expand...
Click to collapse
I recommend flashing to the latest version. https://www.sammobile.com/firmwares/sm-t531/SM-T531/EBE/download/T531XXU1AQC2/176957/
Then re-root the tablet, then follow this video, https://www.youtube.com/watch?v=hV90Idi2STc
Video isn't mine.
Hi all. Can Someone pls tell me what is happening here and what should i do?the phone tried to restart on it's own and now its stuck here on restart screen with this messages
Could not do normal boot.
Ddi : mmc_read failed
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SW- N910F
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
REACTIVATION LOCK: ON
KNOZ WARRANTY VOID: 0X0
QUALCOMM SECUREBOOT: ENABLE ( CSB)
RP SWREV: S1, T1, R1, A1, P1
SECURE DOWNLOAD : ENABLE
UDC START[
And also under the droid it says
Downloading...
Do not turn off target!,
Could it be that you done a Update? you could try a factory reset
Say goodbye to your Note 4, eMMC failure! Samsung wants you to buy a new phone.
Hello , xda-developers,
I have a SM-N910F, and "played" today with the ROM and recovery, trying to root and put a custom recovery.
The Odin part worked smoothly, changed a couple of times the ROM but not succeeding the part with recovery.
After a wrong file being flashed (n915f-cwm-recovery-6.0.5.1(1128)), the screen mistakes the position of my finger onto screen.
Tried flashing stock ROM for it (COA-N910FXXU1ANK4_N910FCOA1ANK1-20141117 -Android 4.4.4 and N910FXXU1DRI2_N910FCOA1DQI1_COA - Android 6.0.1 ),no luck.
Screen not recognise corectly whereis my finger on screen, but the stilus work perfect, also mouse with OTG seems to work fine.
What is to be done to revert this.
Can be fixable?
THX!
find the solution on "https://www.youtube.com/watch?v=eAyZAa8ck8U" sorry for bother, although I would like to resolve the problem with the custom recovery and rooted with Magisk, what are the RIGHT steps
In IDIN mode I have on screen:
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-N910F
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
REACTIVATION LOCK: OFF
KNOX WARRANTARY VOID: 0x1 (4)
QUALCOM SECUREBOOT: ENABLE (CSB)
RP SWREV: S1, T1, R1, A1, P1
SECURE DOWNLOAD : ENABLE
UDC START
MasterMarius said:
find the solution on "https://www.youtube.com/watch?v=eAyZAa8ck8U" sorry for bother, although I would like to resolve the problem with the custom recovery and rooted with Magisk, what are the RIGHT steps
In IDIN mode I have on screen:
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-N910F
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
REACTIVATION LOCK: OFF
KNOX WARRANTARY VOID: 0x1 (4)
QUALCOM SECUREBOOT: ENABLE (CSB)
RP SWREV: S1, T1, R1, A1, P1
SECURE DOWNLOAD : ENABLE
UDC START
Click to expand...
Click to collapse
Open dialer and Dial *#2663#
Press TSP FW UPDATE
Wait until it finished
Reboot device
Done.
This will recalibrate your touch as normal to default.
Hello,
I have one galaxy S5 with official rom.
I used the SmartManager App in RAM Section to do a clean.
I did "end" for few app with the Android Robot logo, afterall, may was not the best idea...
When I reboot my phone, it is stucked in bootloop (until the samsung logo)
I can boot in recovery and download mode. I only have the official recovery.
Do you know if the SmartManager App has a system file where I can activate/desactivate the system apps?
Is it possible to change this kind of file since recovery mode(maybe with custom recovery as TWRP)?
Thank you in advance and for your welcoming
Information got in Download mode :
ODIN MODE
PRODUCT NAME: SM-G900F
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
REACTIVATION LOCK: OFF
KNOX WARRANTY VOID: 0x0
QUALCOMM SECUREBOOT: ENABLE (CSB)
RP SWREV: S1, T1, R1, A1, P1
SECURE DOWNLOAD: ENABLE
UDC START