Database Users

Need Help! Tablet Stuck and Fastboot Not Working

I am sitting dead in the water with an EVGA Tegra Note 7 that can't turn on Wireless and won't let me install drivers to move further or even do a restore.
First off I am using Tomsgt Super Tool: http://forum.xda-developers.com/showthread.php?t=2627654
So my device was continuing to fail an OTA update so I was going to use this device to reinstall the basic 4.4.2. However during the process Fastboot.exe gave a failed message in Windows, but it showed fastboot after the device name. I continued to let it Restore Tegra Note 7 to Android 4.4.2 and first of all it did it way too fast and once it was finished I couldn't get the Wireless to enable. I read another person with the same problem that had to redo the process. Well I can't get past reinstalling ADB and Fastboot, now not even ADB..
I tried uninstalling the device from Windows letting it reinstall and then checking it again. No matter what I do the USB Driver Scan fails over and over. I got this issue the first time, but somehow I got it to catch the device once and install ADB.
1) Yes USB Debugging in Enabled
2) Yes Anti-Virus is Off
3) Bootloader unlocked
4) Tried Different USB Ports
So what the hell is going on here?? All I wanted to do was run a damn OTA update.. Now I have a tablet with no wireless and I obviously can't do an OTA update now.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I was thinking about not using the tool and doing it all manually like I used to do, but all the tool does is auto execute files/folders in specific orders, basically an elaborate .bat file. So if it is failing at ADB, it is going to fail for me manually too.
Please give me some idea of what to do. I don't see how relocking the bootloader would do anything, but aside from that it was a non-rooted stock 4.4.2 OS running.
Is there something I need to do in order to get Impactor to work?
So then I plug the device into a 9 year old laptop with Windows XP and Impactor sees the device on the first try and installs the driver (it takes 2-3 minutes). Then it finishes and I close impactor, but I get an error next saying device not found. I restart the machine and now it is exactly like my desktop, Impactor can't see the device at all.
What in the hell is going on here? If I had known all this was going to happen I would have skipped their damn OTA update that continued to fail.
BTW with XP I can prevent Windows from installing any type of driver, so I did. Should I let XP search for a driver and see what happens?
Someone throw me some ideas, you can see a full explanation of what is happening if you scroll up to my screenshot. I basically have a dead device because I wanted to use this tool to do a recovery...
Wireless refuses to turn on, it just sits there for hours if I let it.
Someone please give me guidance, I was out of the Android scene for a while and I've forgotten a lot of the tricks I used to know.

If your computer is recognizing the fastboot mode that is all you need. Forget the supertool for now.
Can you use the tablet to get into the Fastboot Protocol? It so that will put it in fastboot mode even if it doesn't look like it.
If that works, you can run TWRP or a custom recovery by using ADB and the fastboot command "fastboot boot TWRP_recover.img"
Notice the fastboot "boot", that will only run TWRP once so if you want to on your tablet for good you replace boot with "flash". fastboot flash TWRP_recover.img
You have to make sure the filename is correct with the custom recovery you downloaded.
At this point, put the update you want on your SD card, put that card in the tablet, and go to TWRP or your custom recover and upload the new software.
It sounds complicated but it isn't.

share_needles said:
If your computer is recognizing the fastboot mode that is all you need. Forget the supertool for now.
Can you use the tablet to get into the Fastboot Protocol? It so that will put it in fastboot mode even if it doesn't look like it.
If that works, you can run TWRP or a custom recovery by using ADB and the fastboot command "fastboot boot TWRP_recover.img"
Notice the fastboot "boot", that will only run TWRP once so if you want to on your tablet for good you replace boot with "flash". fastboot flash TWRP_recover.img
You have to make sure the filename is correct with the custom recovery you downloaded.
At this point, put the update you want on your SD card, put that card in the tablet, and go to TWRP or your custom recover and upload the new software.
It sounds complicated but it isn't.
Click to expand...
Click to collapse
Thanks for the suggestions, but I don't think Fastboot has completely installed on my tablet. When I hit Fastboot kernel all I get is a black flash and back to the bootloader again. I believe there is a quick message that flashes the first time I try to select Fastboot, however it's way too fast to read. When I do it again after that is when I will see a black flash, but apparently from what I have heard that is all Fastboot kernel is supposed to do??
How do I verify Fastboot is working before I flash the damn thing?

NCSUZoSo said:
Thanks for the suggestions, but I don't think Fastboot has completely installed on my tablet. When I hit Fastboot kernel all I get is a black flash and back to the bootloader again.
How do I verify Fastboot is working before I flash the damn thing?
Click to expand...
Click to collapse
That is what I was saying when I said you wouldn't even know you're in fastboot. The black-screen with message flashes for a milisecond and goes back to the same screen so it looks like nothing happened when it is actually in fastboot mode.
You can verify this by running your super tool and it will say "fastboot device"
Do you know how to use the ADB command prompt?
Using that, I flashed a custom recovery and then put the below 4.3 zip file on my SD card and going through the tablet I used the TWRP custom recovery to upload 4.3 on the tablet.
I used this old backup of 4.3:
Forum post and links: forum.xda-developers.com/showthread.php?t=2580287
Backupfile name: productionbl_signed_tn7_114gp_2923379__4.3.zip
FYI,
I was in your same situation and that worked for me. I could not get my computer to recognize my device in anything other than fastboot mode.

share_needles said:
That is what I was saying when I said you wouldn't even know you're in fastboot. The black-screen with message flashes for a milisecond and goes back to the same screen so it looks like nothing happened when it is actually in fastboot mode.
You can verify this by running your super tool and it will say "fastboot device"
Do you know how to use the ADB command prompt?
Using that, I flashed a custom recovery and then put the below 4.3 zip file on my SD card and going through the tablet I used the TWRP custom recovery to upload 4.3 on the tablet.
I used this old backup of 4.3:
Forum post and links: forum.xda-developers.com/showthread.php?t=2580287
Backupfile name: productionbl_signed_tn7_114gp_2923379__4.3.zip
FYI,
I was in your same situation and that worked for me. I could not get my computer to recognize my device in anything other than fastboot mode.
Click to expand...
Click to collapse
Can I get some official links for the newest/compatible versions of TWRP and the latest stock ROM I can install that is the most up to date (with Google Apps)?
Sorry to ask, but I am short on time most of the time and I might have an hour or so to work on it tomorrow.

Sorry I don't have official links but it would take you 10mins to find them through google. Good luck.

I have two files which I believe are correct except the TWRP file has an odd extension..
"Shaky156-TWRP-recovery.img.exe"
the other that is supposed to have GApps is: Stock-4.4.2-2.5-TegraNote7.zip
If that zip is only like 440 MB is that even possible? Can someone point me in a better direction if this sounds wrong.
Sources, TWRP: http://forum.xda-developers.com/showthread.php?t=2586432
Actually thinking about it and I bet with having things specific to img files like IMGBurn and other software it may create a .exe so it's easier to emulate it as a disk.
Do we have any good custom ROMs these days you'd suggest over stock? Are any that stable yet? If not can anyone find me a complete download if a 440MB zip is too small to have GApps in it.

I used Fastboot commands to get TWRP installed and Android is "upgrading.." now, so hopefully this will fix it.
I have the tablet up and running going into Google Play now.
I used this thread's link for the latest TWRP (2.7.1.0): http://forum.xda-developers.com/showthread.php?t=2586432
I got a completely stock version of 4.4.2 and OTA shows this as the most up to date version. I got my copy of the 4.4.2 ROM out of the Super Tool's folder that you can find here: http://forum.xda-developers.com/showthread.php?t=2627654
The tricky part to this my first time was I forgot you can open a command window inside the folder that contains TWRP/Fastboot/etc. (hold Shift and Right Click in the folder where all the data is and hit open command window)
Obviously everything came off a SD Card installed into the TN7.

answer for dummies
Hi
Is anyone able to explain how to rectify wifi being turned off constantly in basic non technical talk?
I am not a tech pro and am unsure what to do
All of the above answers are like a different language to me .
Thansks

aimeymarie said:
Hi
Is anyone able to explain how to rectify wifi being turned off constantly in basic non technical talk?
I am not a tech pro and am unsure what to do
All of the above answers are like a different language to me .
Thansks
Click to expand...
Click to collapse
Your best bet is to find someone you know who the above is not a foreign language to. I mean it could be broken down step by step as basic as possible and you may still not understand parts.

[GUIDE] Repair your Idol 3

Hi Everyone
This is Guide how to repair your phone who was dead
My phone doesn't worked for 3 days so i get small trick and successfully repaired from dead
My phone was 5 times not worked like dead,Screen not Works ...only LED works,when i connect to pc usb device not recognized and nothing....
Explanation about my Problem:
IN MY CASE!
and the worst In my case Power button and Volume Buttons doesn't working so i open the BACK COVER eject the cable from volume button and insert small cable in slots to cover the pins like pressing volume up and down and finally connected to pc with usb
So we are starting the GUIDE:
1.First you need the drivers so you can get from this https://drive.google.com/folderview?id=0B1T7tp6tJ_3kX3p6SUxWb2NfWTQ&usp=sharing
2.After you installed the Drivers go to. Download mode if not goes try this... Press Volume UP and Volume DOWN and connect to usb to your pc
3.Go to device Manager to view the Port ,so the port can be "Android HS-USB QDLoader 9008 (COM3)"
4.Download the Panasonic Firmware Eluga and Extract (don't worry this is the same like idol 3 only name changed)https://docs.google.com/uc?id=0B01OmzpKE6vAVDhaSFN2aVFzaVU
5. After Extract you wil find EB-90S55EWLv1009.exe so run as administrator wait to load data
6.select 6045 and in the list down you can find your phone
7.and press the button "download"
8.So process starting ..indetifying your device you will get informations about imei..rooted or no .....
9.so automatically started to flashing the firmware (my it's go to 45 % and then i get error)
10.Don't worry press the button Reboot Device
11.and your device will reboot and you will view 'the screen powered by android and then panasonic so i get message Encrypted device just click the button "reset" and automatically device will be reseted and when wil finish with reset automatically reboots and wait to first boot you will get welcome screen set up and finished.....
12.So device successfully repaired from dead
If you want to go to CM or Stock for Idol 3
-i will write guide to unlock bootloader and flash TWRP recovery
-You must have Minimal Adb and Fastboot
-type "adb reboot-bootloader" to reboot into bootloader. The device should reboot to the screen showing " .powered by android". This is bootloader mode.
-Then type "fastboot -i 0x1bbb devices" should show some numbers and "fastboot" after the numbers
-Type "fastboot -i 0x1bbb oem device-info" shows device info including bootloader status (e.g. locked).
-Type "fastboot -i 0x1bbb oem unlock" to unlock the bootloader; after this you should get, for device info,
-Type "fastboot -i 0x1bbb oem device-info" and you should see "Device unlocked: true"
-You successfully unlocked the bootloader one step more to flash the recovery
-Download the TWRP RECOVERY FROM THIS LINK:
https://www.androidfilehost.com/?fid=24421527759881858
-Then copy from when you downlaod and paste the recovery in C:\Program Files\Minimal ADB and Fastboot
-Press Shift in the directory and click Right on mouse and open command promt here
-Type fastboot -i 0x1bbb flash recovery twrp-3.0.0-1.img or fastboot -i 0x1bbb boot twrp-3.0.0-1.img (if you want to test before installation)
-so successfully installed recovery and flash CM Or whatever you want
[/SIZE][/COLOR][/B]
Sorry for Grammatical Errors!
This guide will repair from dead.... ​

in my case , buttons also doesn't work , how did you opened the back cover?

xZrender said:
in my case , buttons also doesn't work , how did you opened the back cover?
Click to expand...
Click to collapse
here's video how you can open
https://www.youtube.com/watch?v=FrFE8FdTXrY

Alek Dev said:
Hi Everyone
IN MY CASE!
and the worst In my case Power button and Volume Buttons doesn't working so i open the BACK COVER eject the cable from volume button and insert small cable in slots to cover the pins like pressing volume up and down and finally connected to pc with usb​
Click to expand...
Click to collapse
i opened back cover , but how did you press the volume button , it doesnt work for me , i ont know what to do ;/

xZrender said:
i opened back cover , but how did you press the volume button , it doesnt work for me , i ont know what to do ;/
Click to expand...
Click to collapse
Eject cable from motherboatd....insert small cable in slots to cover the pins like pressing volume up and down and finally connected to pc with usb

problem with idol 3 4.7 6039K
Hi there,
I don't know if this is the correct section, I hope so, otherwise I really appreciate you can drive me to the appropriate one, it's new for me this forum!
I have an idol 3 4.7, where I have installed kingroot and after I took out (I didn´t reset the phone, Just unistall the app),
yesterday i received the update system message, I imagine for the marshmallow update, so I say Yes, install it.
But the phone entered in bootloop. I only have the initial screen with the options as Reboot system, adb and so on.
I tried to wipe but nothing. So now my phone stucked. I tried with an assistance center in Quito but they could't
My questions are:
may I use this system for 6039K?
Or does anybody hear about a solution in this case?
Should I open and take out the battery?
Please, any suggestion will be really welcome in order to make the phone work again.
P.

nipozzano said:
Hi there,
I don't know if this is the correct section, I hope so, otherwise I really appreciate you can drive me to the appropriate one, it's new for me this forum!
I have an idol 3 4.7, where I have installed kingroot and after I took out (I didn´t reset the phone, Just unistall the app),
yesterday i received the update system message, I imagine for the marshmallow update, so I say Yes, install it.
But the phone entered in bootloop. I only have the initial screen with the options as Reboot system, adb and so on.
I tried to wipe but nothing. So now my phone stucked. I tried with an assistance center in Quito but they could't
My questions are:
may I use this system for 6039K?
Or does anybody hear about a solution in this case?
Should I open and take out the battery?
Please, any suggestion will be really welcome in order to make the phone work again.
P.
Click to expand...
Click to collapse
Hello
This Guide only works with Idol 3 5.5
but i will explain how to restore your device
Can you try with Mobile upgrade Q to restore,if doesn't work
Use this guide from wiemar ,it should help to you because it's for your model
http://forum.xda-developers.com/showpost.php?p=63709274&postcount=113
If you any questions ask me

Hi ! I follow the guide up to the section 9, unfortunately, in the Panasonic Firmware Eluga and Extract after pressing download it stops after 2% and I have got the error message "load nprg error error code 5002". Does someone know how to fix that ?
Thanks !

Error
I get: "Master Clear: FAIL Flash Status: [COM3->PC[3]] COM3->PC[3] failed to erase misc (Error code = 40016) " :crying:
Now I get the same error that matcail... did you solved it ???

Good tutorial but it does not help me. My phone keeps on rebooting.

Schumi_wk said:
Good tutorial but it does not help me. My phone keeps on rebooting.
Click to expand...
Click to collapse
Tell me info About your phone? Model,Country,ROM...../?

All is standard, no root, no twrp and the latest software from alcatel, the model is 6045Y. But all of a sudden my phone decided to random reboot and it didn't stop
So i looked to unbrick it and came with a couple of options, first i tried to sideload software but that didn't work, than i tried it with Mobile upgrade from alcatel and that didn't work.
Than i saw this thread and tried it twice but after Panasonic and the sound it starts to reboot again. Now i'm trying again with Mobile upgrade.
All that is changed is the recovery interface it looks now like it is from MM.

Schumi_wk said:
All is standard, no root, no twrp and the latest software from alcatel, the model is 6045Y. But all of a sudden my phone decided to random reboot and it didn't stop
So i looked to unbrick it and came with a couple of options, first i tried to sideload software but that didn't work, than i tried it with Mobile upgrade from alcatel and that didn't work.
Than i saw this thread and tried it twice but after Panasonic and the sound it starts to reboot again. Now i'm trying again with Mobile upgrade.
All that is changed is the recovery interface it looks now like it is from MM.
Click to expand...
Click to collapse
More Looks like Hardware Problem Try again with Mobile q if not works...Send to warranty repair.....

Alek, thank you for this great guide. It saved my 6045k model.
I was messing around with AlekOS 3.0, had issues with lock screen and experimented with modems. I managed to permanently disable secondary sim slot (was using famewolf's modem backups). I forgot to copy modem.img backup to my PC! Also tried bunch of TWRP backups with no luck. My last hope was Mobile Upgrade Q and reverting back tu 5.0.2. Unfortunately with no success (only one sim slot is recognized again).
Finally I found this thread, followed the guide and I can confirm that it did solve sim issue. The setup finished with no errors that you mentioned. It got stuck at 45%, but after a while (10min) it completed successfully.
Cheers!

I'm in the same situation as you,but my problem is that Panasonic Eluga doesn't recognice my devide,drivers are correctly installed,I checked everything but nothing:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I´ve tried everything to downgrade my device (Mobile Q doesn't work) but nothing :crying:

peito said:
I'm in the same situation as you,but my problem is that Panasonic Eluga doesn't recognice my devide,drivers are correctly installed,I checked everything but nothing:
I´ve tried everything to downgrade my device (Mobile Q doesn't work) but nothing :crying:
Click to expand...
Click to collapse
You must do something Wrong...Press Pwr button and Volume up and down and thern connect to PC and then you will get RED SCREEN....Press Volume Up until you get Black screen and then press Download and if you get again same Send me Pm with Teamviewer ID AND PASS and i will try to help you

eXoSaX said:
Alek, thank you for this great guide. It saved my 6045k model.
I was messing around with AlekOS 3.0, had issues with lock screen and experimented with modems. I managed to permanently disable secondary sim slot (was using famewolf's modem backups). I forgot to copy modem.img backup to my PC! Also tried bunch of TWRP backups with no luck. My last hope was Mobile Upgrade Q and reverting back tu 5.0.2. Unfortunately with no success (only one sim slot is recognized again).
Finally I found this thread, followed the guide and I can confirm that it did solve sim issue. The setup finished with no errors that you mentioned. It got stuck at 45%, but after a while (10min) it completed successfully.
Cheers!
Click to expand...
Click to collapse
Alek Dev said:
You must do something Wrong...Press Pwr button and Volume up and down and thern connect to PC and then you will get RED SCREEN....Press Volume Up until you get Black screen and then press Download and if you get again same Send me Pm with Teamviewer ID AND PASS and i will try to help you
Click to expand...
Click to collapse
That is exactly what I'm doing,entering in Download mode and then download in the Panasonic software,but nothing,the program cannot read my phone,I'm really tired of trying this,I will stuck in your Alek rom (btw,no matter how many times I flash your modem,I cannot get the lock screen ).Ty anyway Alek and keep it up!!!!

Was on alek 3.0 before bootloop appear after a strange warning on android about battery, now got bootloop, no twrp access etc
try ur solution but after 45% and error, reboot and no screen about panasonic only bootloop
11.and your device will reboot and you will view 'the screen powered by android and then panasonic so i get message Encrypted device just click the button "reset" and automatically device will be reseted and when wil finish with reset automatically reboots and wait to first boot you will get welcome screen set up and finished.....
Click to expand...
Click to collapse
already tried SUGAR+QCT_SP+v10.5.1(4pda source) and mobile upgrade q 5.0.9, both finished without error after 100% but still bootloop
i think it s total broke with motherboard pb or battery

thorfr said:
Was on alek 3.0 before bootloop appear after a strange warning on android about battery, now got bootloop, no twrp access etc
try ur solution but after 45% and error, reboot and no screen about panasonic only bootloop
already tried SUGAR+QCT_SP+v10.5.1(4pda source) and mobile upgrade q 5.0.9, both finished without error after 100% but still bootloop
i think it s total broke with motherboard pb or battery
Click to expand...
Click to collapse
Looks Like Problem With Motherboard and Battery ..you can try again with Panasonic Firmware Tool and if this not help Send it to Warranty Repair

ok i m gonna send it to warr:crying:antly
retry mobil q upgrage wo success bootloop again

Yoga Tab 2 8" 830f failed update led to soft lock

So I downloaded a 16mb OTA update and let the tablet do its thing without touching it. I waited for the tablet to boot up, but it was stuck in a black screen for about 12 minutes until I decided to turn it off and on. It didn't work, so I went to the recovery to do a factory reset and clear the cache, but it still didn't work. I later went to this Russian forum here from this thread. I downloaded a lollipop rom and proceeded to flash it using Phone Flash Tool Ver. 5.2. It went well until 16% in where it failed. Unfortunately, I don't have a screenshot of this.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
(image of the files in the rom I downloaded)
After all this happened, I tried to start it up but I got the message "Boot Failed. EFI Hard Drive. Boot Successful - Enter Setup"
And now it won't go into recovery mode, but it does go into fastboot and bios setup.
Since it does go into fastboot, I tried to use a tool from this thread (Temp recovery) to use a temporary cwm recovery to hopefully be able to at least boot into that, but that didn't end up working.
I got another rom from the same Russian site that had differently packaged files but still the same stock lollipop rom.
I tried to just use the recovery from there to manually flash it using fastboot, but it still failed.
I later found this thread with these instructions for this problem.
1. download and extract this file someplace on your pc
2. uninstall your existing Phone Flash Tool and from the drivers folder install both files (Intel Phone Flash Tool and Android Driver accepting defaults) reboot pc when finished
3. place your tab in DNX mode (from power off press and hold both volume keys then press pwr to start, in a few you screen will show "Fastboot starting..." message and hang on that. you must get that message on your tab screen, restart from power off until you have it)
4. start the installed Phone Flash Tool and load flash.xml from the extracted YT2-830L... folder then Start Flashing, it will reboot when done
Click to expand...
Click to collapse
The file he linked in his post (ionioni ) was gone but I still tried to do this with the roms I had. And guess what? It still didn't work. The instructions said to place the tablet in DNX mode (meaning fastboot), which I did do...only when I put it into fastboot, it was set to DNX_OS which came to say "Wrong device state" in Phone Flash Tool.
I've tried what I could, but failed. Anyone have any suggestions?

AgentXGhost said:
So I downloaded a 16mb OTA update and let the tablet do its thing without touching it. I waited for the tablet to boot up, but it was stuck in a black screen for about 12 minutes until I decided to turn it off and on. It didn't work, so I went to the recovery to do a factory reset and clear the cache, but it still didn't work. I later went to this Russian forum here from this thread. I downloaded a lollipop rom and proceeded to flash it using Phone Flash Tool Ver. 5.2. It went well until 16% in where it failed. Unfortunately, I don't have a screenshot of this.
(image of the files in the rom I downloaded)
After all this happened, I tried to start it up but I got the message "Boot Failed. EFI Hard Drive. Boot Successful - Enter Setup"
And now it won't go into recovery mode, but it does go into fastboot and bios setup.
Since it does go into fastboot, I tried to use a tool from this thread (Temp recovery) to use a temporary cwm recovery to hopefully be able to at least boot into that, but that didn't end up working.
I got another rom from the same Russian site that had differently packaged files but still the same stock lollipop rom.
I tried to just use the recovery from there to manually flash it using fastboot, but it still failed.
I later found this thread with these instructions for this problem.
The file he linked in his post (ionioni ) was gone but I still tried to do this with the roms I had. And guess what? It still didn't work. The instructions said to place the tablet in DNX mode (meaning fastboot), which I did do...only when I put it into fastboot, it was set to DNX_OS which came to say "Wrong device state" in Phone Flash Tool.
I've tried what I could, but failed. Anyone have any suggestions?
Click to expand...
Click to collapse
This is the file you need https://drive.google.com/file/d/0B1LaMEhefCBgYzNTOUxJZmtWQ0E/view
And this https://01.org/android-ia/downloads/intel-platform-flash-tool-lite
Ignore the oops error warning, it's something to do with what G drive can scan.

Holy Sh!t. this just absolutely worked!! I didn't think I could bring this thing back to life, but the files you linked just did it! Really, I don't know how to thank you enough for this.

corasman said:
This is the file you need https://drive.google.com/file/d/0B1LaMEhefCBgYzNTOUxJZmtWQ0E/view
And this https://01.org/android-ia/downloads/intel-platform-flash-tool-lite
Ignore the oops error warning, it's something to do with what G drive can scan.
Click to expand...
Click to collapse
Hi folks,
had the exact same issue and indeed the 1st link offered (https://drive.google.com/file/d/0B1LaMEhefCBgYzNTOUxJZmtWQ0E/view) worked like a charm.
The second link is to download the "Intel platform flash tool lite", but I used my existing version of the Intel Phone Flash Tool (5.2.1-0) which worked fine with the image.
In other words, Corasman, it appears you have saved 2 people's life (or at least tablets) with your solution, so Thanks ! :good:
Regards.

Make that 3 people! Thank you so much corasman - your post has finally fixed my yoga 2 tablet, which I was sure would be going in the bin. Can't overstate how grateful I am - Cheers!

update 830f with 1050f rom?
updating 830f with 1050 rom? does it work?

hello. I have the same problem. I update OTA to lolipop. Since the table is slow, i tried flashing some ROM (which i cannot recall) and the tablet stopped working. Now, I am trying to flash the link you provided and it succeed. However after that i get blank Screen. what Could be wrong. My table is YT2 830LC. Please help

I am typing this all over again after my full report vanished. Do not have the patience of typing all that again. Suffice to say I had a similar situation with the boot failed EFI Hard Drive. Boot Successful - Enter Setup" message on my 830LC.
I had even found the bios restore tool for moving back from lollipop to kitkat but it too would hang. And attempts to flash lollipop would fail immediately with the same message as the OP, wrong device state.
So, in spite of it seeming completely counter-intuitive, I flashed the 1050F rom in the link shared by Corasman. Strange as it may seem, my tablet is now alive and working. No calling function, but it is working and calling itself a 1050F.
Now my research has to shift to whether the 830 LC rom can be flashed now.

i have a same problem with yoga 2 pro 1380f mr corasmancan help me

prabuddhadg said:
I am typing this all over again after my full report vanished. Do not have the patience of typing all that again. Suffice to say I had a similar situation with the boot failed EFI Hard Drive. Boot Successful - Enter Setup" message on my 830LC.
I had even found the bios restore tool for moving back from lollipop to kitkat but it too would hang. And attempts to flash lollipop would fail immediately with the same message as the OP, wrong device state.
So, in spite of it seeming completely counter-intuitive, I flashed the 1050F rom in the link shared by Corasman. Strange as it may seem, my tablet is now alive and working. No calling function, but it is working and calling itself a 1050F.
Now my research has to shift to whether the 830 LC rom can be flashed now.
Click to expand...
Click to collapse
i have same problem with my yoga 830lc this rom not work help me to run my tab agian
---------- Post added at 10:55 AM ---------- Previous post was at 10:47 AM ----------
corasman said:
This is the file you need
And this
Ignore the oops error warning, it's something to do with what G drive can scan.
Click to expand...
Click to collapse
hy sir downlod the rom from google drive but unable to download 2nd link (link not working)
i use latest intel flas tool light but the rom no flash to my device its show errors. plese sir help me to run my tab again

Apply update from sdcard FAILED : Rooted Crosscall Trekker M1 on BOOTLOOP

Hi there ! Hope you're doing all right
I had a lot of issues recently with my phone : Crosscall Trekker M1
It all begin when I started to remove entirely Google from the phone.
I rooted it and took the liberty to delete all that mention google.
I unfortunately delete a system file and that how my problems began.
(I called couple of times the Technique Assistance from Crosscall's Website but they weren't able to help me and I had the same story with the SAV --> the after selling's services. I gave up about asking them help and I decided to solve the issue by my own.)
So for now the phone start on bootloop, (I cannot use the OS anymore) so I can launch it in Recovery mod only.
After days of researchs I found the original stock rom for the Trekker M1 !!
On the recovery : After I wiped data and cache of course :
I tried to install the Rom with the option : "Apply update from sd card" but it didn't worked.
So I tried to install differents Custom Recovery like CWM and even renamed them update.zip but I had the exact same issue:
"E : failed to verify whole-file signature
E : signature verification failed
Installation aborted."
I also wanted to try Odin but apparently Crosscall's phones doesn't have a recuperation mod (I dream that someone got me wrong on this :crying: )
I've got a few clues about all this :
I guess the Debugging USB Mod isn't enable anymore on the phone
Maybe the versions of ClockWorkMod weren't compatible at all with my phone.
All I know is that the phone is rooted;
The recovery's version is : "Android system recovery <3e> LMY47V release-keys"
So know you know everything
Does someone think, he or she can help me with this ?
Thank you for your attention !

Brazyxs said:
Hi there ! Hope you're doing all right
I had a lot of issues recently with my phone : Crosscall Trekker M1
It all begin when I started to remove entirely Google from the phone.
I rooted it and took the liberty to delete all that mention google.
I unfortunately delete a system file and that how my problems began.
(I called couple of times the Technique Assistance from Crosscall's Website but they weren't able to help me and I had the same story with the SAV --> the after selling's services. I gave up about asking them help and I decided to solve the issue by my own.)
So for now the phone start on bootloop, (I cannot use the OS anymore) so I can launch it in Recovery mod only.
After days of researchs I found the original stock rom for the Trekker M1 !!
On the recovery : After I wiped data and cache of course :
I tried to install the Rom with the option : "Apply update from sd card" but it didn't worked.
So I tried to install differents Custom Recovery like CWM and even renamed them update.zip but I had the exact same issue:
"E : failed to verify whole-file signature
E : signature verification failed
Installation aborted."
I also wanted to try Odin but apparently Crosscall's phones doesn't have a recuperation mod (I dream that someone got me wrong on this :crying: )
I've got a few clues about all this :
I guess the Debugging USB Mod isn't enable anymore on the phone
Maybe the versions of ClockWorkMod weren't compatible at all with my phone.
All I know is that the phone is rooted;
The recovery's version is : "Android system recovery <3e> LMY47V release-keys"
So know you know everything
Does someone think, he or she can help me with this ?
Thank you for your attention !
Click to expand...
Click to collapse
Hello,
Can you capture files included in update.zip?

-Hope- said:
Hello,
Can you capture files included in update.zip?
Click to expand...
Click to collapse
By uptade.zip do you think about the Rom or the Custom Recovery ?
And yes I can

Brazyxs said:
By uptade.zip do you think about the Rom or the Custom Recovery ?
And yes I can
Click to expand...
Click to collapse
Can u copy the stock ROM name before renaming it to update.zip and yeah I meant the update.zip

-Hope- said:
Can u copy the stock ROM name before renaming it to update.zip and yeah I meant the update.zip
Click to expand...
Click to collapse
Here's the name of the stock rom :
LU652R(HS-L635)_L1185.6.02.00.EU00_MultiDownload_201601292005_user.tar.gz
To correct what I said first : I didn't renamed the Rom in fact, I did it only with the CWM file who was actually in zip format
(Sorry about that)
I couldn't even try to install the Rom because the Recovery doesn't recognize it

Brazyxs said:
Here's the name of the stock rom :
LU652R(HS-L635)_L1185.6.02.00.EU00_MultiDownload_201601292005_user.tar.gz
To correct what I said first : I didn't renamed the Rom in fact, I did it only with the CWM file who was actually in zip format
(Sorry about that)
I couldn't even try to install the Rom because the Recovery doesn't recognize it
Click to expand...
Click to collapse
Can u provide me with a pic of the tar.gz file (the files inside it)

-Hope- said:
Can u provide me with a pic of the tar.gz file (the files inside it)
Click to expand...
Click to collapse
Here's 4 captures of the tar.gz opened with Winzip
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
View attachment 4279786
View attachment 4279787
View attachment 4279788

Brazyxs said:
Here's 4 captures of the tar.gz opened with Winzip
View attachment 4279785
View attachment 4279786
View attachment 4279787
View attachment 4279788
Click to expand...
Click to collapse
Sorry for late reply however these files aren't falshable through recovery
they are flashed through QFIL
there are files called prog_emmc_firehose,rawprogram.xml, and patch.xml which is used to flash through qfil

-Hope- said:
Sorry for late reply however these files aren't falshable through recovery
they are flashed through QFIL
there are files called prog_emmc_firehose,rawprogram.xml, and patch.xml which is used to flash through qfil
Click to expand...
Click to collapse
Thank you very much ! I will check about QFIL by myself. For now I'm happy that someone care about my issues
I tell you if there is something new !

-Hope- said:
Sorry for late reply however these files aren't falshable through recovery
they are flashed through QFIL
there are files called prog_emmc_firehose,rawprogram.xml, and patch.xml which is used to flash through qfil
Click to expand...
Click to collapse
So it appear that the Crosscall M1 got an emergency mode. I can launch it by pressing Vol + and Vol - when I'm plugging the phone to a computer by USB.
At this moment a message show up :
"Authority indentification not found !"
"Long press power key to continue ..."
and if I do it :
No update file in TFcard!
X
Update failed!
Long press power key to power off.
If I start the phone on Emergency Mode with QFIL working (what I need to do) nothing happen.
I still have the message No Port Available on the top of QFIL.
So I'm wondering,
Do you think I can fix in some ways that problem of unrecognized device ?
or
Is there a way that I can install the Rom by choosing to install it as an update with the Emergency Mode. The Rom files would be the update that i put before in a "TFcard" in some format ?

Brazyxs said:
So it appear that the Crosscall M1 got an emergency mode. I can launch it by pressing Vol + and Vol - when I'm plugging the phone to a computer by USB.
At this moment a message show up :
"Authority indentification not found !"
"Long press power key to continue ..."
and if I do it :
No update file in TFcard!
X
Update failed!
Long press power key to power off.
If I start the phone on Emergency Mode with QFIL working (what I need to do) nothing happen.
I still have the message No Port Available on the top of QFIL.
So I'm wondering,
Do you think I can fix in some ways that problem of unrecognized device ?
or
Is there a way that I can install the Rom by choosing to install it as an update with the Emergency Mode. The Rom files would be the update that i put before in a "TFcard" in some format ?
Click to expand...
Click to collapse
Can you try to run it as an admin then choose the right com and try again ?

-Hope- said:
Can you try to run it as an admin then choose the right com and try again ?
Click to expand...
Click to collapse
I tried to run QFIL as an admin but it doesn't make a difference. The thing is that my device isn't recognize at all by my computer.
I sorry but what do you mean what "choose the right com" ?

Brazyxs said:
I tried to run QFIL as an admin but it doesn't make a difference. The thing is that my device isn't recognize at all by my computer.
I sorry but what do you mean what "choose the right com" ?
Click to expand...
Click to collapse
Did you install the qcom drivers

-Hope- said:
Did you install the qcom drivers ?
Click to expand...
Click to collapse
Hi, Here's the list of all the drivers I installed :
Qualcomm_USB_Driver_V1.0
MTK_USB_All_V1.0.8
ADBDriverInstaller
I also installed :
Android-sdk
Java SE Development Kit

After a lot of research my device still isn't showing on QFIL.
But for a time he showed up on "ADB Driver installer". I plugged the phone by USB and started it with a special combinaison (almost like the Emergency Mode's combinaison) that I'm still trying to remember.
There is also another a new thing. If I start my device that I plug before by USB and only with the power button :
My computer recognize it and the Driver Software Installation try to install MTP USB Device.
The operation failed everytime but for now I'm happy that the device is recognize.

Brazyxs said:
After a lot of research my device still isn't showing on QFIL.
But for a time he showed up on "ADB Driver installer". I plugged the phone by USB and started it with a special combinaison (almost like the Emergency Mode's combinaison) that I'm still trying to remember.
There is also another a new thing. If I start my device that I plug before by USB and only with the power button :
My computer recognize it and the Driver Software Installation try to install MTP USB Device.
The operation failed everytime but for now I'm happy that the device is recognize.
View attachment 4284734
Click to expand...
Click to collapse
Just reread the post, try to do a factory reset

-Hope- said:
Just reread the post, try to do a factory reset
Click to expand...
Click to collapse
The factory reset isn't working (and I just tried one more time), that is why I need to flash my rom.

Brazyxs said:
The factory reset isn't working (and I just tried one more time), that is why I need to flash my rom.
Click to expand...
Click to collapse
wait you said that adb works, if you can find the file system from an exact phone uploaded or you know that its common you can push it using adb if you are rooted

-Hope- said:
wait you said that adb works, if you can find the file system from an exact phone uploaded or you know that its common you can push it using adb if you are rooted
Click to expand...
Click to collapse
Yes I did said that, adb worked for a time.
I'm not sure to understand what you mean by "the file system" and "push it " with adb
The thing I'm sure of is that I'm rooted :good:
I'll continue my researchs.

oneplus 6T stuck on fastboot bootloop

hi team, i just bought a new oneplus 6T from china with Hydrogen OS, i changed it to Oxygen OS
but somehow it erased completly and stuck on fastboot bootloop, no bootloader, no recovery no system
i tried MsmdownloadTooln the laptop reconizes the phone but the operation stuck also on "param preprocessing"
please any help i would be greatful :crying::crying:

ritork said:
hi team, i just bought a new oneplus 6T from china with Hydrogen OS, i changed it to Oxygen OS
but somehow it erased completly and stuck on fastboot bootloop, no bootloader, no recovery no system
i tried MsmdownloadTooln the laptop reconizes the phone but the operation stuck also on "param preprocessing"
please any help i would be greatful :crying::crying:
Click to expand...
Click to collapse
Hey there I recently had the same problem with a OnePlus 6T... What I did was I installed everything manually using the ADB tools, in fastboot mode. Everything worked fine afterwards. Follow this guide, it will hopefully help.(It helped me ;D)
https://www.google.com/amp/s/forum....-stock-fastboot-roms-oneplus-6t-t3862516/amp/

Ethos001 said:
Hey there I recently had the same problem with a OnePlus 6T... What I did was I installed everything manually using the ADB tools, in fastboot mode. Everything worked fine afterwards. Follow this guide, it will hopefully help.(It helped me ;D)
https://www.google.com/amp/s/forum....-stock-fastboot-roms-oneplus-6t-t3862516/amp/
Click to expand...
Click to collapse
thanks for ur respond
i did this command "flash-all-partitions" but it showed me only "failed respond"
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

ritork said:
thanks for ur respond
i did this command "flash-all-partitions" but it showed me only "failed respond"
Click to expand...
Click to collapse
Make sure to have unzipped the compressed android file from the guide(whichever you decided to donwload) in the same folder as your ADB and Fastboot tools.
If it is still not working... try to manually flash everything in fastboot mode, that is what I did...
Download the latest version of android pie provided in the link from the guide( Google drive or Android Filehost), and then make sure to unzip the compressed file in the same folder where you installed your ADB and Fastboot Tool. Make sure a TWRP recovery image is in the same folder. (https://forum.xda-developers.com/on...overy-unofficial-twrp-touch-recovery-t3861482)
Then, what you should do is to follow the guide where it says:
MANUAL FLASH: Windows - OSX - Linux
Get back to me after you finished. Read twice, execute once :good:

Ethos001 said:
Make sure to have unzipped the compressed android file from the guide(whichever you decided to donwload) in the same folder as your ADB and Fastboot tools.
If it is still not working... try to manually flash everything in fastboot mode, that is what I did...
Download the latest version of android pie provided in the link from the guide( Google drive or Android Filehost), and then make sure to unzip the compressed file in the same folder where you installed your ADB and Fastboot Tool. Make sure a TWRP recovery image is in the same folder. (https://forum.xda-developers.com/on...overy-unofficial-twrp-touch-recovery-t3861482)
Then, what you should do is to follow the guide where it says:
MANUAL FLASH: Windows - OSX - Linux
Get back to me after you finished. Read twice, execute once :good:
Click to expand...
Click to collapse
Thanks a lot my friend
It works now after the second try
Thank u very much .. i really apreciate ur support mate

ritork said:
Thanks a lot my friend
It works now after the second try
Thank u very much .. i really apreciate ur support mate
Click to expand...
Click to collapse
Hey bud you are welcome ;P
I know how frustrating it was, as I have been in the exact same situation... Took me like 4 hours to figure it out ;D
Glad to help

Ethos001 said:
Hey bud you are welcome ;P
I know how frustrating it was, as I have been in the exact same situation... Took me like 4 hours to figure it out ;D
Glad to help
Click to expand...
Click to collapse
Thanks again mate <3

Ethos001 said:
Hey bud you are welcome ;P
I know how frustrating it was, as I have been in the exact same situation... Took me like 4 hours to figure it out ;D
Glad to help
Click to expand...
Click to collapse
Hey, i want to flash oxygenos on my chinese variant with hydrogenos. could you help me with the installation in order to avoid this kind of problems(bootloop,brick etc.)?

HackerGames197 said:
Hey, i want to flash oxygenos on my chinese variant with hydrogenos. could you help me with the installation in order to avoid this kind of problems(bootloop,brick etc.)?
Click to expand...
Click to collapse
PM me

Gracie mille !!! First brick and i hope never again but you where there.. Huge thanks.

Download the TOOL ALL IN ONE and if it says fastboot device connected, I think you'll be fine. Make sure right below that you choose OnePlus 6T. Then just download and flash the full rom and it fixed mine, I had the same problem.

bigmikey307 said:
Download the TOOL ALL IN ONE and if it says fastboot device connected, I think you'll be fine. Make sure right below that you choose OnePlus 6T. Then just download and flash the full rom and it fixed mine, I had the same problem.
Click to expand...
Click to collapse
Thanks a lot.
Would you share the link of the TOOL ALL IN ONE?
I also have the same bootloop issue.

Micheal86 said:
Thanks a lot.
Would you share the link of the TOOL ALL IN ONE?
I also have the same bootloop issue.
Click to expand...
Click to collapse
https://forum.xda-developers.com/android/software/tool-tool-one-driversunlocktwrpfactory-t3358711
Hope this helps

I have the same problem
PLeaseeee help me I have a rooted oneplus 6t. I performed a backup and wipe in hope to clear a problem and am now stuck in fastboot mode. Im pretty sure as I tried to reboot it said no os detected, and then I got stuck. I have tried to install the latest oxygen os by manualling flashing 4 files. all tutorials i read have bootloader and other files while i just have - system_matrix , system_manifest , vendor_matrix, vendor_menifest (XML files by the way). I have flashed these files and rebooted only to go back to the fastboot screen.

Ethos001 said:
Hey bud you are welcome ;P
I know how frustrating it was, as I have been in the exact same situation... Took me like 4 hours to figure it out ;D
Glad to help
Click to expand...
Click to collapse
Bro please help me I didn't not much about this things but ill do flashing and customisation i bricked my Oneplus 6t its stuck on bootloader ill try msm tool also its shows param preprocessing ?
And my bootloader is also locked how can i solve this problem pls help me

For anyone running into a similar problem these are the steps I used
1. Download and extract files
a. Qualcomm drivers
b. MSM Oneplus 6t download Tool
2. Disable Driver Signature Enforcement by restarting your pc whilst holding shift, Choose trouble shoot, then going into more recovery ,select Advanced Options > Startup Settings > and then click on Restart.
3. Now PC will restart and Now you will see a list of startup settings that you can change. Select option 7 ‘Disable Driver Signature Enforcement’ by clicking f7
4. Now switch off your phone (by navigating through fast boot options)
5. While switched off hold both vol up + down for 5secs before connecting to your pc. *Your pc should recognise a phone is connected however nothing will be displayed on your phone*
6. Open device manager from start- Under Other devices there should be your phone (although it will be called smthn else), right click that and select update drivers
7. Browse computer for driver software and select folder with extracted QUALCOMM drivers (for me it was called unbrick).
8. The open the MSM application (run as admin tho) it should say device connected
9. Press start and you download should start- if error occurs or download stops unplug, power on, power off and the plug it again, now it should be fine.
10. Wait for download to finish and then your phone should be rebooted
---------- Post added at 09:58 PM ---------- Previous post was at 09:57 PM ----------
mohitgaba14 said:
Bro please help me I didn't not much about this things but ill do flashing and customisation i bricked my Oneplus 6t its stuck on bootloader ill try msm tool also its shows param preprocessing
And my bootloader is also locked how can i solve this problem pls help me
Click to expand...
Click to collapse
Look at the post above