Related
* I don't know enough to be messing with this, but here I am.
** My device is rooted, but I got into this mess by updating (device was working fine, did not use 3rd party software) and when it restarted after install it went to boot loader.
*** Device only turns on when its plug into wall outlit for 20 seconds. I can not get it to turn on with power button or when its plugged into laptop. Not sure if this is normal or not.
**** Something similar happened to this before but I just used twrp and fixed it. I can not flash a recovery unless my nexus is working normally.
***** Yes, I read other threads, on this forums and others, havnt found anything that has helped. I figured i could post specific details that other threads were lacking.
My nexus 10 is currently stuck in boot loader. If I select recovery mode, it does not switch to the smaller green android, that you can press down power, volume down/up and get into TWRP. Nothing I have done has gotten me anywhere except boot loader. I have tried to use Nexus Root Tool Kit and use the Flash Stock + Unroot and Flash Image to various partitions. No success. Today, downloaded Odin 3.07, but it crashed when file analysis in message box.
Im downloading SDK tools right now, but Im not quite sure what those are, will have to experiment.
See attached files please.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Image of recovery that I can not get to.
Current state of device. can not get anywhere else.
Close up of date.
Picture of odin failing. I tried to flash using the option called PDA by the way.
Picture of options Im trying to use on NRT. I also tired flash stock +unroot but no change to device.
solved - cant find where to set this thread to solved thought.
Any help is greatly appreciated.
Nyreb said:
* I don't know enough to be messing with this, but here I am.
** My device is rooted, but I got into this mess by updating (device was working fine, did not use 3rd party software) and when it restarted after install it went to boot loader.
*** Device only turns on when its plug into wall outlit for 20 seconds. I can not get it to turn on with power button or when its plugged into laptop. Not sure if this is normal or not.
**** Something similar happened to this before but I just used twrp and fixed it. I can not flash a recovery unless my nexus is working normally.
***** Yes, I read other threads, on this forums and others, havnt found anything that has helped. I figured i could post specific details that other threads were lacking.
My nexus 10 is currently stuck in boot loader. If I select recovery mode, it does not switch to the smaller green android, that you can press down power, volume down/up and get into TWRP. Nothing I have done has gotten me anywhere except boot loader. I have tried to use Nexus Root Tool Kit and use the Flash Stock + Unroot and Flash Image to various partitions. No success. Today, downloaded Odin 3.07, but it crashed when file analysis in message box.
Im downloading SDK tools right now, but Im not quite sure what those are, will have to experiment.
See attached files please.
View attachment 2637629
Image of recovery that I can not get to.
View attachment 2637596
Current state of device. can not get anywhere else.
View attachment 2637598
Close up of date.
View attachment 2637611
Picture of odin failing. I tried to flash using the option called PDA by the way.
View attachment 2637622
Picture of options Im trying to use on NRT. I also tired flash stock +unroot but no change to device.
Any help is greatly appreciated.
Click to expand...
Click to collapse
Shoot me a email at [email protected]... We can talk more about your issues there..... Thx lj
Solution
Thanks to lj50036, my nexus now actually works.
Here's what he told me to do:
----------
1.) start here http://forum.xda-developers.com/showthread.php?t=2588979
This will install abd fastboot and the drivers for your tablet just follow instructions.
2.) Now open cmd as admin and type
fastboot
should see commands and options listed
3.) now type
cd /
this will move root to c drive.
4.) plug in tablet, boot into bootloader (holding down power, volume up and down I think) and type
fastboot devices
this output serial number of device and then type of device (Fastboot)
5.) go to https://developers.google.com/android/nexus/images#mantaray or google factory images and find Nexus 10. use what ever version you want. download, unzip and you should see something along the lines of this (the kot49h will be what ever version of the image you used.)
6,) move everything but the 2 .sh files to root of c drive (c:/)
and then in cmd prompt type
dir
this will print out file names, data, and other information of c:/. make sure you see the 3 files you moved from the factory image you unzipped.
7.) if so, make sure tablet is in bootloader still, and type
flash-all.bat in cmd prompt.
--About halfway through it reboots your nexus and because my nexus wont reboot its self, and will only come on when its plugged into wall outlet for a bit, I just did that and plugged in and it worked fine.
-- once the whole process runs, my nexus rebooted into recovery mode, and after a minute rebooted correctly and I was able to start setting up.
----------------
Thank you again to lj50036
@Nyreb
Change the forum name to include (SOLVED)
@lj50036
So I had mostly the same problem happen, except I tried to get into recovery to flash a CM11, but I was completely stock. It would get stuck on the screen below. I did what you said to do above and it still sticks at the same screen it did before, except sometimes it shows the Google logo before getting stuck. It used to just show the android on it's back right off the bat. Not sure what to do anymore.
spudsmac said:
@lj50036
So I had mostly the same problem happen, except I tried to get into recovery to flash a CM11, but I was completely stock. It would get stuck on the screen below. I did what you said to do above and it still sticks at the same screen it did before, except sometimes it shows the Google logo before getting stuck. It used to just show the android on it's back right off the bat. Not sure what to do anymore.
Click to expand...
Click to collapse
Shoot me a email.... Sounds like you need some help....
So I ended up emailing @lj50036 and we went back and forth and had to reflash everything, including custom recovery, TWRP. I think the recovery was messed up.
Finally works again!
spudsmac said:
So I ended up emailing @lj50036 and we went back and forth and had to reflash everything, including custom recovery, TWRP. I think the recovery was messed up.
Finally works again!
Click to expand...
Click to collapse
What happen in android some time, and I may be way off in left field here but, it has happened this way on the tf700, tf300, tf201, and the nexus 10... Just what I have help people with is that....
The storage no matter what command you issue in fastboot e.g
Code:
fastboot erase boot
fastboot erase system
fastboot -w
It just will not erase everything, and by doing these commands your really only telling the tab and or phone that you are going to be putting other
data in those partitions, so if you just flash exactly what was already on the tablet it does not like it...
@spudsmac had upgraded to 4.4.2 and was trying to install cm11 when things went wrong
So by us trying to reset the tablet to factory 4.4.2 firmware it would not take it... Just froze at android guy with x
So when, we went one version older on the firmware... Magic happened and he was golden....
Thx Josh
*****DISCLAIMER*****DISCLAIMER*****DISCLAIMER*****
If you brick your device it's a whole lot of NOT MY PROBLEM
*****DISCLAIMER*****DISCLAIMER*****DISCLAIMER*****
With that out of the way enjoy
1) Download this
https://www.androidfilehost.com/?fid=95747613655047389
2) unzip: V510_4.4.4+tools.zip
3) Install the LG drivers
4) Install LGFlashTools v1.8 (but don't run it)
5) Copy MegaLock.dll to C:\LG\LGFlashTool, This is a hidden folder so enable "hidden folders". Replace the old MegaLock.dll file if you have already installed LG Flash Tool on your computer
6) Launch LG Flash Tool
You might see a window with Korean language, just click on OK
Check the Select Manual Mode on the top
7) MAKE SURE UNDER, DEVICE MANAGER, YOUR PORT IS SET TO COM 41 FOR YOUR DEVICE.
8) Click the DLL box and choose LHV510_SVC_LGFLASHv160.dll
9) Click the S/W box and select the firmware file with .tot extension
10) Now click the Yellow arrow button on the top left of the main window
11) Boot your V510 into Download Mode. To do this power V510 completely off. Then hold Volume Up + Volume Down + plug in USB to PC (in that order)
The firmware installation will be triggered
Ignore if you see any temporary error and just wait patiently till it is finished.
I took these instructions from another post. That post ended by giving "Credit [email protected] for making a cleaner guide for the TOT Method"
It's a shame the v500 can't be converted
n0credit said:
It's a shame the v500 can't be converted
Click to expand...
Click to collapse
This might help: http://goo.gl/rPx8KK
+1 worked perfectly for me.
The only part that I had a little trouble with was changing the COM port to 41.
Windows users: you must be booted into Download Mode for the tablet to show up in Device Manager, where you change the COM port. I was trying to change the port while the tablet was booted up (normally) and it was driving me crazy.
Need some help:
tl;dr: Pretty sure I still need to flash the stock recovery, but having problems.
Coming from a rooted LG GPad GPE with TWRP installed. I followed the instructions on this thread and everything seems to have worked. I'm now unrooted, but I'm still getting "your system is up to date" when I check for an update in settings.
I think I do not have the right recovery installed, and that is why I am not getting the update. When I try to boot into recovery mode, I get the android guy on his back with a red triangle. No signs of TWRP being installed anymore.
I've tried several times to flash the stock recovery as listed in this thread: http://forum.xda-developers.com/showthread.php?t=2574639. It seems to work, but I don't think it is working properly. I also can't sideload the 5.0 file through ADB, since I need to put the device into recovery mode to do it.
---------- Post added at 02:24 PM ---------- Previous post was at 01:46 PM ----------
Nevermind. Turns out that is the stock recovery. Now my problem is I can't push the file over ADB. The ADB connection doesn't persist into recovery mode. I've followed the steps here: http://forum.xda-developers.com/showthread.php?t=2575783.
When the device is on normally, the ADB connection is fine. It shows up in the list of connected devices. When I reboot into recovery and choose "apply update from ADB" and then enter "adb devices" I get no devices connected.
In device manager, I see "LG-V510" under "other devices" but when I try to manually update the drivers to the google drivers as indicated in the post above, the computer says "Windows could not find driver software for your device."
Still need help...
mcaurilio said:
Need some help:
tl;dr: Pretty sure I still need to flash the stock recovery, but having problems.
Coming from a rooted LG GPad GPE with TWRP installed. I followed the instructions on this thread and everything seems to have worked. I'm now unrooted, but I'm still getting "your system is up to date" when I check for an update in settings.
I think I do not have the right recovery installed, and that is why I am not getting the update. When I try to boot into recovery mode, I get the android guy on his back with a red triangle. No signs of TWRP being installed anymore.
I've tried several times to flash the stock recovery as listed in this thread: http://forum.xda-developers.com/showthread.php?t=2574639. It seems to work, but I don't think it is working properly. I also can't sideload the 5.0 file through ADB, since I need to put the device into recovery mode to do it.
---------- Post added at 02:24 PM ---------- Previous post was at 01:46 PM ----------
Nevermind. Turns out that is the stock recovery. Now my problem is I can't push the file over ADB. The ADB connection doesn't persist into recovery mode. I've followed the steps here: http://forum.xda-developers.com/showthread.php?t=2575783.
When the device is on normally, the ADB connection is fine. It shows up in the list of connected devices. When I reboot into recovery and choose "apply update from ADB" and then enter "adb devices" I get no devices connected.
In device manager, I see "LG-V510" under "other devices" but when I try to manually update the drivers to the google drivers as indicated in the post above, the computer says "Windows could not find driver software for your device."
Still need help...
Click to expand...
Click to collapse
I guess I'm not quite sure what you were trying to accomplish. If it is to install TWRP. You need to use fastboot from download mode and flash your recovery there, rather than trying to use adb from the recovery itself. "Fastboot flash recovery palman.img". , where palman.img is the name of whatever recovery you want to flash.
Fairly certain I did everything correctly according to the directions. When I press the yellow arrow about how long does it take to complete the install? When i started it, little box came up said some things that I don't remember and after about 30 seconds, the little box went away and the COM41 box says Ready!! Does that mean its finished? Just dont want to unplug tablet before the process is finished and brick it. Thanks
Nevermind, figured it out. Had to unplug device and plug usb back in and that triggered it to start.
sleekmason said:
I guess I'm not quite sure what you were trying to accomplish. If it is to install TWRP. You need to use fastboot from download mode and flash your recovery there, rather than trying to use adb from the recovery itself. "Fastboot flash recovery palman.img". , where palman.img is the name of whatever recovery you want to flash.
Click to expand...
Click to collapse
No, I was trying to sideload the 5.0 upgrade. Couldn't get my adb connection to persist through to recovery mode. Finally figured it out and was able to get the tablet upgraded this morning - but I had to use the TWRP backup method. Everything seems to be good to go now though!
Correct drivers
I'm having problems getting the port changed to 41 and I think it because the drivers aren't installing correctly. Could someone confirm from the screenshot below that I'm on the right track, or maybe post a shot of what the correct driver set-up should look like? Thanks.
**Edit: Got it, I did have the wrong drivers.
I don't think you have the right drivers installed. There should be two of them and mine were both banged-out yellow, but only when in download mode and with the software running. You don't even have a ports tab to change it (or you have the wrong device).
I gave up and restored the Lollipop backup someone posted, which worked great except then I had to re-root and flash TWRP again.
-MX- said:
I'm having problems getting the port changed to 41 and I think it because the drivers aren't installing correctly. Could someone confirm from the screenshot below that I'm on the right track, or maybe post a shot of what the correct driver set-up should look like? Thanks.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Click to expand...
Click to collapse
If drivers are installed correctly, you should find it under Ports(COM & LPT) expand that and LG should be there. Right click and properties and find the COM41
shawn13165 said:
If drivers are installed correctly, you should find it under Ports(COM & LPT) expand that and LG should be there. Right click and properties and find the COM41
Click to expand...
Click to collapse
Yeah, definitely wrong drivers, had to do some uninstalling/reinstalling and finally got it to work.
Colchiro said:
I don't think you have the right drivers installed. There should be two of them and mine were both banged-out yellow, but only when in download mode and with the software running. You don't even have a ports tab to change it (or you have the wrong device).
I gave up and restored the Lollipop backup someone posted, which worked great except then I had to re-root and flash TWRP again.
Click to expand...
Click to collapse
I had given up for the 4.4.4 update when it initially came out and upgraded through TWRP, but now I'm running into issues with not being able to use the external SD card from the TWRP backup of LP that was posted, so I figured I needed to give this method a shot and do it right.
Any chance we will get the 5.0 TOT file for the v510? I tried following this guide: http://forum.xda-developers.com/showthread.php?t=2220801 and also tried using wireshark to capture the path in the LG Support tool but haven't had any luck with either method.
Thanks man. This helped me restore my G Pad when I thought all hope was lost.
Thank you very much, this worked perfect!
OK, first, I have searched the internet and XDA for help.
Currently, I'm stuck on The black screen with Google. It shows the unlocked Bootloader icon as well. Earlier today I was stuck in a boot with CM boot animation, but that's apparently gone now. I can fastboot, so I'm pretty sure it's recoverable. In TWRP, it says unable to mount /system, /data/ cache/ storage, basically everything. Using NRT i've flashed stock everything, which didn't work, so I tried flashing the kernel, which also didn't work, so I tried the bootloader and system, but they all result in the google splash screen. I am completely out of ideas.
Question: How do i fix it?
Edit: It stayed on the splash screen for at least 4 hours and it wasn't caused by anything I did. No ROM flashes, nothing. It was working then it wasn't.
a.child said:
OK, first, I have searched the internet and XDA for help.
Currently, I'm stuck on The black screen with Google. It shows the unlocked Bootloader icon as well. Earlier today I was stuck in a boot with CM boot animation, but that's apparently gone now. I can fastboot, so I'm pretty sure it's recoverable. In TWRP, it says unable to mount /system, /data/ cache/ storage, basically everything. Using NRT i've flashed stock everything, which didn't work, so I tried flashing the kernel, which also didn't work, so I tried the bootloader and system, but they all result in the google splash screen. I am completely out of ideas.
Question: How do i fix it?
Edit: It stayed on the splash screen for at least 4 hours and it wasn't caused by anything I did. No ROM flashes, nothing. It was working then it wasn't.
Click to expand...
Click to collapse
If you are using NRT, try to flash stock with soft-bricked/Bootloop option.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
After restore, perform a wipe data/factory reset in stock recovery before booting to android.
Best of luck
joegestes said:
If you are using NRT, try to flash stock with soft-bricked/Bootloop option.
After restore, perform a wipe data/factory reset in stock recovery before booting to android.
Best of luck
Click to expand...
Click to collapse
Thanks for the help, you even edited a screenshot :') haha unfortunately, no luck. But some interesting stuff happens when I do the stock flash.
First time I tried (yesterday), I went through the instructions just how they're listed, I erased all user data and rebooted, still stuck. This time, though, I couldn't get it to boot the stock recovery. Tried pwr+Vol Up like the directions say, but it gets stuck on splash. Tried Pwr+Vol down and I could boot into TWRP which informed me that it was still unable to mount any partitions and that there was no OS installed.
Edit: Looked closer at the command prompt log from the flash and noticed it failed to write any of the images. Sending is OKAY but writing FAILED.
a.child said:
Thanks for the help, you even edited a screenshot :') haha unfortunately, no luck. But some interesting stuff happens when I do the stock flash.
First time I tried (yesterday), I went through the instructions just how they're listed, I erased all user data and rebooted, still stuck. This time, though, I couldn't get it to boot the stock recovery. Tried pwr+Vol Up like the directions say, but it gets stuck on splash. Tried Pwr+Vol down and I could boot into TWRP which informed me that it was still unable to mount any partitions and that there was no OS installed.
Edit: Looked closer at the command prompt log from the flash and noticed it failed to write any of the images. Sending is OKAY but writing FAILED.
Click to expand...
Click to collapse
Hmmm.
Its possible your cable is no good, but it could be something else like a driver issue or charging port failure.
Try using a known good, high quality data cable. Also try connecting to a different USB port on PC.
Just so I understand better.
What version of android did you attempt to flash?
Were you using NRT to flash when the flashing's failed?
Was Force Flash enabled in NRT? .......Try that.
Did you try flashing a different version of STOCK android?
Do you have Android ADB/fastboot installed on PC aside from the one in NRT?
If so, does fastboot detect your phone when running the command "fastboot devices" while in the bootloader?
Is ADB able to detect your phone when running the command "ADB devices" while in TWRP?
I'm at work now, but I'll try new cables and ports when I get home as well as the adb commands.
I was trying to flash 5.0.1 , and was running some CM12 nightly when it failed. To be clear, the ROM was working fine until it wasn't.
I was using NRT and I had force flash selected (recommended settings I think), but I'm not 100% sure post flash factory reset was checked but in the CMD log I did see it wipe and attempt to write userdata.
I have not tried a different version of stock.
I believe ADB is installed outside of NRT abd i have to manually set my path variable to C:/ADB (which screws up normal command prompt, but idk how to fix that) for NRT to work. I have a 2013 nexus 7 and used the same setup to flash PA a while back without any issues.
NRT doesn't detect my phone when displaying the splash screen, but idk about TWRP.
joegestes said:
Hmmm.
Its possible your cable is no good, but it could be something else like a driver issue or charging port failure.
Try using a known good, high quality data cable. Also try connecting to a different USB port on PC.
Just so I understand better.
What version of android did you attempt to flash?
Were you using NRT to flash when the flashing's failed?
Was Force Flash enabled in NRT? .......Try that.
Did you try flashing a different version of STOCK android?
Do you have Android ADB/fastboot installed on PC aside from the one in NRT?
If so, does fastboot detect your phone when running the command "fastboot devices" while in the bootloader?
Is ADB able to detect your phone when running the command "ADB devices" while in TWRP?
Click to expand...
Click to collapse
So the computer does not recognize a fastboot device while in TWRP, but does in the BL.
I attempted to flash 5.0 with the settings mentioned, no luck
a.child said:
So the computer does not recognize a fastboot device while in TWRP, but does in the BL.
I attempted to flash 5.0 with the settings mentioned, no luck
Click to expand...
Click to collapse
If you are absolutely certain your cable is a good one, it is possible you have a driver issue, but I doubt it.
You could try deleting/uninstalling you current ADB driver set and then install the following ADB clockworkmod universal drivers . It might help.
64bit
32bit
If you decide to install the drivers. make sure you select "Android Composite ADB Interface"
after installing the driver set
If that does not help, I am sorry to say, you are likely looking at a hardware failure of the charging port(Dock Connector &Flex Cable)
It looks easy and economical to replace. I found the part here, but you could Google around. I have no experience with the following site.
http://www.repairsuniverse.com/lg-nexus-4-e960-dock-connector-flex-cable-replacement.html
If it were my N4(still great phone), I'd replace the part and attempt to re-flash.
Best of luck.
joegestes said:
If you are absolutely certain your cable is a good one, it is possible you have a driver issue, but I doubt it.
You could try deleting/uninstalling you current ADB driver set and then install the following ADB clockworkmod universal drivers . It might help.
64bit
32bit
If you decide to install the drivers. make sure you select "Android Composite ADB Interface"
after installing the driver set
If that does not help, I am sorry to say, you are likely looking at a hardware failure of the charging port(Dock Connector &Flex Cable)
It looks easy and economical to replace. I found the part here, but you could Google around. I have no experience with the following site.
http://www.repairsuniverse.com/lg-nexus-4-e960-dock-connector-flex-cable-replacement.html
If it were my N4(still great phone), I'd replace the part and attempt to re-flash.
Best of luck.
Click to expand...
Click to collapse
Thanks for the links, I might give it a go.
I bought an original Moto x last night for $100 and I was going to root the potatoes out of it, but who knew non-nexus phones were so difficult to unlock? Damn AT&T....
I sort of suspected it was a hardware issue when I was getting nowhere with NRT, but I wanted confirmation from someone more knowledgeable than me. Any idea on the likelyhood it is something other than the port? The bit that concerns me is that TWRP was unable to mount any partitions, but then again, if i couldn't connect while in TWRP, sort of sounds like a port issue.
oh well...
a.child said:
Thanks for the links, I might give it a go.
I bought an original Moto x last night for $100 and I was going to root the potatoes out of it, but who knew non-nexus phones were so difficult to unlock? Damn AT&T....
Click to expand...
Click to collapse
LOL....That's why I mostly stick with Nexus devices. No carrier garbage, global bands, unlockable and plenty of potatoes:laugh:
a.child said:
Any idea on the likelyhood it is something other than the port?.
Click to expand...
Click to collapse
Could be a bad eMMC but I doubt that. Port failure is more likely to be the issue based on your inability to ADB devices in TWRP.
a.child said:
The bit that concerns me is that TWRP was unable to mount any partitions, but then again, if i couldn't connect while in TWRP, sort of sounds like a port issue
Click to expand...
Click to collapse
Its harder know exactly when using NRT.
That is one reason why, IMO, it is far better to use Fastboot commands to flash instead of relying on toolkit automation.(I do think NRT is the best toolkit)
My guess is NRT sends erase commands to a partition before flash attempts which then failed or sometimes, when a port goes bad,
it is intermittent, a partial flash occurs which would also explain why TWRP can,t mount a particular partition.
For ten bucks delivered on eBay its a no brainier to change out the port. It will probably fix it and if not, you'll have learned something.
joegestes said:
LOL....That's why I mostly stick with Nexus devices. No carrier garbage, global bands, unlockable and plenty of potatoes:laugh:
Could be a bad eMMC but I doubt that. Port failure is more likely to be the issue based on your inability to ADB devices in TWRP.
Its harder know exactly when using NRT.
That is one reason why, IMO, it is far better to use Fastboot commands to flash instead of relying on toolkit automation.(I do think NRT is the best toolkit)
My guess is NRT sends erase commands to a partition before flash attempts which then failed or sometimes, when a port goes bad,
it is intermittent, a partial flash occurs which would also explain why TWRP can,t mount a particular partition.
For ten bucks delivered on eBay its a no brainier to change out the port. It will probably fix it and if not, you'll have learned something.
Click to expand...
Click to collapse
Well i replaced the port and the battery and i'm having the same problem. And I did check to make sure I didn't reinstall the old port.
Guess she's dead :'(
Hmmm... You can connect in fastboot mode, right?
How about re-locking and unlocking the bootloader? It helped me several times...
You'll have to search about how to use fastboot. Connect your phone to your pc while in fastboot mode, and type this into terminal window :
fastboot oem lock
(Press enter)
(bootloader will be locked)
fastboot oem unlock
(Press enter)
(Phone's screen will display sth, use volume keys and power keys to unlock the bootloader)
(It will erase itself)
ddaggebi said:
Hmmm... You can connect in fastboot mode, right?
How about re-locking and unlocking the bootloader? It helped me several times...
You'll have to search about how to use fastboot. Connect your phone to your pc while in fastboot mode, and type this into terminal window :
fastboot oem lock
(Press enter)
(bootloader will be locked)
fastboot oem unlock
(Press enter)
(Phone's screen will display sth, use volume keys and power keys to unlock the bootloader)
(It will erase itself)
Click to expand...
Click to collapse
Thanks for the suggestion, but it didn't work. I was able to lock and unlock the bootloaded again, but it didn't have any effect.
Have you tried flashing Jellybean or kitkat stock rom by fastboot?
If that doesn't work, then the problem is within EMMC. You'll have to let her go...
ddaggebi said:
Have you tried flashing Jellybean or kitkat stock rom by fastboot?
If that doesn't work, then the problem is within EMMC. You'll have to let her go...
Click to expand...
Click to collapse
Looking at other forums, pretty sure the emmc is dead, but I'll try flashing an older version.
This guide will help you unbrick your hardbricked MeMo pad or possibly other device. For the purpose of this guide, hardbricked will refer to a device's software being damaged to the point where standard procedures and utilities (adb, fastboot, recovery, etc.) will not be able to make the device functional again. In order to be hardbricked, you essentially need to erase or damage the bootloader. Without the bootloader, you can't use fastboot or recovery since all of those things require the bootloader. This guide addresses that situation (your device should be displaying nothing but the USB logo, as seen in the attachment). If you have a working bootloader and can run fastboot commands, THIS GUIDE IS NOT FOR YOU and will only possibly make things worse.
This guide is directed towards the ME170CX, which is also apparently called the ME70C or KO1A; however, the same process should work for other MeMo Pad devices and even other Intel devices. I cannot provide much help for other devices, so try at your own risk.
Do not follow this guide unless it is your last hope or you know what you are doing. I am not responsible for any damage you cause to your device in any way.
We will use the Intel Phone Flash tool, which can be used with a variety of Intel devices to flash firmware. You can use the Manufacturing Flash Tool instead if you'd like.
Here are the steps:
Obtain and install all drivers and software from the bottom of this post.
Download the factory image zip from the manufacturer's website; make sure it matches your device before flashing!. Extract the contents of the zip. Extract the contents of ifwi.zip into the same folder.
Plug in the device and open the Phone Flash tool. In the Phone Flash Tool window, click on "Custom Flash" on the left and pick "system (blankphone)" from the Type dropdown.
For each of the first four files, pick the one that matches:
CLVp_CSAX_FWR_DnX_20.3E.bin for FW DnX
IFWI_v64.25_CSAX_PROD.bin for IFWI
CLVp_CSAX_OS_DnX_20.3E.bin for OS DnX
fastboot.img for OS Image (this doesn't seem right, but it worked for me)
Once the four images are in place, click "Register flash file". At this point, your device should be displayed in the white rectangle on the page and the start flash button should now be clickable. Press the button, and flashing will commence. If you see "Windriver Error: 0x20000015, Timeout expired" in the console, try rebooting the device and flashing before the USB logo comes up (the device will appear in the Flash Tool before the logo comes up).
After a few seconds, you should see the Intel splash screen and you will be taken to droidboot. From there, it should be fairly easy to recover the device.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
If you encounter any issues or corrections, please respond to this thread and let me know. Also, I was getting tons of driver errors (Windriver Error: 0x20000015, Timeout expired) the second time I tried to do this. The trick seems to be pressing the flash button before the USB logo appears.
I discovered most of this information from these two resources:
https://www.youtube.com/watch?v=jh89aiepcjQ
http://www.asus-zenfone.com/2014/11/how-to-unbrick-zenfone-5-and-zenfone-6_8.html
REQUIRED DRIVERS AND SOFTWARE
iSocUSB Driver
Intel USB Driver for Android Devices
Intel Phone Flash Tool
Hey @korockinout13!
1st of all, thanks for this, I have hard bricked my ME70cx and I needed a solution...
Unfortunately it is not working... I have followed your instructions but I keep getting the error "Windriver Error: 0x20000015, Timeout expired"
I have reinstalled the drivers (iSOC and Intel USB) but nothing changes, the same error keeps appearing.
You say "The trick seems to be pressing the flash button before the USB logo appears." BUT the start flash button is only clickable AFTER the USB logo appears
Any help shall be appreciated
Premie said:
Hey korockinout13!
1st of all, thanks for this, I have hard bricked my ME70cx and I needed a solution...
Unfortunately it is not working... I have followed your instructions but I keep getting the error "Windriver Error: 0x20000015, Timeout expired"
I have reinstalled the drivers (iSOC and Intel USB) but nothing changes, the same error keeps appearing.
You say "The trick seems to be pressing the flash button before the USB logo appears." BUT the start flash button is only clickable AFTER the USB logo appears
Any help shall be appreciated
Click to expand...
Click to collapse
I literally faught that error for a whole day. I tried 5 different computers, all had that issue. Usually my tablet would connect and disconnect once before the logo came up. Within that brief window, I was able to start the flash and it worked. I'm pretty sure that's what did it. If you aren't seeing this, turn up your PC's volume and listen for the USB sounds.
This whole thing is pretty annoying, but when it works, it works.
Thanks
I shall keep going at it until it works or I find another solution.
PLEASE help me!
korockinout13 said:
This guide will help you unbrick your hardbricked MeMo pad or possibly other device. For the purpose of this guide, hardbricked will refer to a device's software being damaged to the point where standard procedures and utilities (adb, fastboot, recovery, etc.) will not be able to make the device functional again. In order to be hardbricked, you essentially need to erase or damage the bootloader. Without the bootloader, you can't use fastboot or recovery since all of those things require the bootloader. This guide addresses that situation (your device should be displaying nothing but the USB logo, as seen in the attachment). If you have a working bootloader and can run fastboot commands, THIS GUIDE IS NOT FOR YOU and will only possibly make things worse.
This guide is directed towards the ME170CX, which is also apparently called the ME70C or KO1A; however, the same process should work for other MeMo Pad devices and even other Intel devices. I cannot provide much help for other devices, so try at your own risk.
Do not follow this guide unless it is your last hope or you know what you are doing. I am not responsible for any damage you cause to your device in any way.
We will use the Intel Phone Flash tool, which can be used with a variety of Intel devices to flash firmware. You can use the Manufacturing Flash Tool instead if you'd like.
Here are the steps:
Obtain and install all drivers and software from the bottom of this post.
Download the factory image zip from the manufacturer's website; make sure it matches your device before flashing!. Extract the contents of the zip. Extract the contents of ifwi.zip into the same folder.
Plug in the device and open the Phone Flash tool. In the Phone Flash Tool window, click on "Custom Flash" on the left and pick "system (blankphone)" from the Type dropdown.
For each of the first four files, pick the one that matches:
CLVp_CSAX_FWR_DnX_20.3E.bin for FW DnX
IFWI_v64.25_CSAX_PROD.bin for IFWI
CLVp_CSAX_OS_DnX_20.3E.bin for OS DnX
fastboot.img for OS Image (this doesn't seem right, but it worked for me)
Once the four images are in place, click "Register flash file". At this point, your device should be displayed in the white rectangle on the page and the start flash button should now be clickable. Press the button, and flashing will commence. If you see "Windriver Error: 0x20000015, Timeout expired" in the console, try rebooting the device and flashing before the USB logo comes up (the device will appear in the Flash Tool before the logo comes up).
After a few seconds, you should see the Intel splash screen and you will be taken to droidboot. From there, it should be fairly easy to recover the device.
If you encounter any issues or corrections, please respond to this thread and let me know. Also, I was getting tons of driver errors (Windriver Error: 0x20000015, Timeout expired) the second time I tried to do this. The trick seems to be pressing the flash button before the USB logo appears.
I discovered most of this information from these two resources:
https://www.youtube.com/watch?v=jh89aiepcjQ
http://www.asus-zenfone.com/2014/11/how-to-unbrick-zenfone-5-and-zenfone-6_8.html
REQUIRED DRIVERS AND SOFTWARE
iSocUSB Driver
Intel USB Driver for Android Devices
Intel Phone Flash Tool
Click to expand...
Click to collapse
Hello,
My device has a screwed up boot partition, but not the bootloader. My question is, how do I get this to flash without going into the USB mode?
Nandr0idC0nsumer said:
Hello,
My device has a screwed up boot partition, but not the bootloader. My question is, how do I get this to flash without going into the USB mode?
Click to expand...
Click to collapse
If you have a working boot loader, you don't need to do this.
korockinout13 said:
If you have a working boot loader, you don't need to do this.
Click to expand...
Click to collapse
Then how do I unbrick my device? I need to flash a new boot partition.
Some background: I installed the Lollipop update, then flashed the kitkat boot and fastboot IMG files (your average stupid Ryan). Can't get into fastboot anymore
Nandr0idC0nsumer said:
Then how do I unbrick my device? I need to flash a new boot partition.
Some background: I installed the Lollipop update, then flashed the kitkat boot and fastboot IMG files (your average stupid Ryan). Can't get into fastboot anymore
Click to expand...
Click to collapse
What happens instead of fastboot mode?
korockinout13 said:
What happens instead of fastboot mode?
Click to expand...
Click to collapse
"Fastboot Starting...
Fastboot Starting#1...
Fastboot Starting#2...
Fastboot Starting#3..."
Hangs there until rebooting after about 2 minutes."
Nandr0idC0nsumer said:
"Fastboot Starting...
Fastboot Starting#1...
Fastboot Starting#2...
Fastboot Starting#3..."
Hangs there until rebooting after about 2 minutes."
Click to expand...
Click to collapse
Hmm... I don't know what that is. Looks like you're in the same boat as me. I am also trying to force a way in to this mode.
korockinout13 said:
Hmm... I don't know what that is. Looks like you're in the same boat as me. I am also trying to force a way in to this mode.
Click to expand...
Click to collapse
Only thing I can think of is using "adb sideload" and making a ZIP to flash lollipop boot.img and droidboot.img
---------- Post added at 05:49 PM ---------- Previous post was at 05:28 PM ----------
korockinout13 said:
Hmm... I don't know what that is. Looks like you're in the same boat as me. I am also trying to force a way in to this mode.
Click to expand...
Click to collapse
Any other thoughts on what I could try? Leaving to eat in about an hour, and if this ain't fixed by then, I'll probably bring this to bestbuy as well
Nandr0idC0nsumer said:
Only thing I can think of is using "adb sideload" and making a ZIP to flash lollipop boot.img and droidboot.img
---------- Post added at 05:49 PM ---------- Previous post was at 05:28 PM ----------
Any other thoughts on what I could try? Leaving to eat in about an hour, and if this ain't fixed by then, I'll probably bring this to bestbuy as well
Click to expand...
Click to collapse
You have adb? That's not possible unless you are getting past the boot loader.
korockinout13 said:
You have adb? That's not possible unless you are getting past the boot loader.
Click to expand...
Click to collapse
Booting normally results in an "error" screen. randomly spamming vol up+vol down+power (SPAM!) brings up recovery, then do "apply update from adb." it puts it in a special adb where you can only use adb sideload
Nandr0idC0nsumer said:
Booting normally results in an "error" screen. randomly spamming vol up+vol down+power (SPAM!) brings up recovery, then do "apply update from adb." it puts it in a special adb where you can only use adb sideload
Click to expand...
Click to collapse
Hm... seems like you should be able to work with that if you have something flashable.
korockinout13 said:
Hm... seems like you should be able to work with that if you have something flashable.
Click to expand...
Click to collapse
Returned the tablet at Best Buy to get "fixed" (come on bestbuy, I know you mean replaced.) Thanks for your help
Repair
Hi,
I think i can help you out because i worked with the intel tool for weeks now to find a solution to root the me581cl.
Go to my thread and download a newer version of intelPhone tool.
http://forum.xda-developers.com/general/help/root-downgrade-asus-me581cl-t3075678
If you crashed your tab totaly, you must put the 4 OS IFWI,dnx files like in the first post and then also boot.img, fastboot.img, recovery.img.
Uncheck only the ifwi folder, but select it before. So its possible to check blank phone and on demand flash.
Then click start flash and the files get loadet up. Now push vol+ and vol- togehter and plug in the device.
(device must be off before you plug it in. If not, press 10 sec the power button.)
The reest you can read in my thread. A downgrade from Android 5 to 4.4 is also possible.
Good luck
Guys, my ME176CX is shafted after completing the L update, it boots to the android with the red exclamation box...i can get past this by using the volume + & power and arrive in the recovery. from there I have tried the wipe cache/wipe userdata (doesn't help) also i tried to adb sideload one of the roms in the collection of roms thread. no good. ideas??
Any solution?
I have a ME176CX, I upgraded the SO I got the message "it said 'Unable to detect power status' for me was weird but I keep going pressing the volume button it started but in the black screen with this message:
"FastBoot Starting...
FastBoot Starting...#1
FastBoot Starting...#2
FastBoot Starting...#3" I don't know what to do, It doesn't move from this screen.
Man I'm living in Venezuela a bad country to get damaged any gadget everything is 5 times expensive who your country and without any help in our soil by ASUS.
is this solution applicable to non-intel memopad? (e.g. me172V)
playinghier said:
is this solution applicable to non-intel memopad? (e.g. me172V)
Click to expand...
Click to collapse
No, this is very specific to the Intel chipset.
So I downloaded a 16mb OTA update and let the tablet do its thing without touching it. I waited for the tablet to boot up, but it was stuck in a black screen for about 12 minutes until I decided to turn it off and on. It didn't work, so I went to the recovery to do a factory reset and clear the cache, but it still didn't work. I later went to this Russian forum here from this thread. I downloaded a lollipop rom and proceeded to flash it using Phone Flash Tool Ver. 5.2. It went well until 16% in where it failed. Unfortunately, I don't have a screenshot of this.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
(image of the files in the rom I downloaded)
After all this happened, I tried to start it up but I got the message "Boot Failed. EFI Hard Drive. Boot Successful - Enter Setup"
And now it won't go into recovery mode, but it does go into fastboot and bios setup.
Since it does go into fastboot, I tried to use a tool from this thread (Temp recovery) to use a temporary cwm recovery to hopefully be able to at least boot into that, but that didn't end up working.
I got another rom from the same Russian site that had differently packaged files but still the same stock lollipop rom.
I tried to just use the recovery from there to manually flash it using fastboot, but it still failed.
I later found this thread with these instructions for this problem.
1. download and extract this file someplace on your pc
2. uninstall your existing Phone Flash Tool and from the drivers folder install both files (Intel Phone Flash Tool and Android Driver accepting defaults) reboot pc when finished
3. place your tab in DNX mode (from power off press and hold both volume keys then press pwr to start, in a few you screen will show "Fastboot starting..." message and hang on that. you must get that message on your tab screen, restart from power off until you have it)
4. start the installed Phone Flash Tool and load flash.xml from the extracted YT2-830L... folder then Start Flashing, it will reboot when done
Click to expand...
Click to collapse
The file he linked in his post (ionioni ) was gone but I still tried to do this with the roms I had. And guess what? It still didn't work. The instructions said to place the tablet in DNX mode (meaning fastboot), which I did do...only when I put it into fastboot, it was set to DNX_OS which came to say "Wrong device state" in Phone Flash Tool.
I've tried what I could, but failed. Anyone have any suggestions?
AgentXGhost said:
So I downloaded a 16mb OTA update and let the tablet do its thing without touching it. I waited for the tablet to boot up, but it was stuck in a black screen for about 12 minutes until I decided to turn it off and on. It didn't work, so I went to the recovery to do a factory reset and clear the cache, but it still didn't work. I later went to this Russian forum here from this thread. I downloaded a lollipop rom and proceeded to flash it using Phone Flash Tool Ver. 5.2. It went well until 16% in where it failed. Unfortunately, I don't have a screenshot of this.
(image of the files in the rom I downloaded)
After all this happened, I tried to start it up but I got the message "Boot Failed. EFI Hard Drive. Boot Successful - Enter Setup"
And now it won't go into recovery mode, but it does go into fastboot and bios setup.
Since it does go into fastboot, I tried to use a tool from this thread (Temp recovery) to use a temporary cwm recovery to hopefully be able to at least boot into that, but that didn't end up working.
I got another rom from the same Russian site that had differently packaged files but still the same stock lollipop rom.
I tried to just use the recovery from there to manually flash it using fastboot, but it still failed.
I later found this thread with these instructions for this problem.
The file he linked in his post (ionioni ) was gone but I still tried to do this with the roms I had. And guess what? It still didn't work. The instructions said to place the tablet in DNX mode (meaning fastboot), which I did do...only when I put it into fastboot, it was set to DNX_OS which came to say "Wrong device state" in Phone Flash Tool.
I've tried what I could, but failed. Anyone have any suggestions?
Click to expand...
Click to collapse
This is the file you need https://drive.google.com/file/d/0B1LaMEhefCBgYzNTOUxJZmtWQ0E/view
And this https://01.org/android-ia/downloads/intel-platform-flash-tool-lite
Ignore the oops error warning, it's something to do with what G drive can scan.
Holy Sh!t. this just absolutely worked!! I didn't think I could bring this thing back to life, but the files you linked just did it! Really, I don't know how to thank you enough for this.
corasman said:
This is the file you need https://drive.google.com/file/d/0B1LaMEhefCBgYzNTOUxJZmtWQ0E/view
And this https://01.org/android-ia/downloads/intel-platform-flash-tool-lite
Ignore the oops error warning, it's something to do with what G drive can scan.
Click to expand...
Click to collapse
Hi folks,
had the exact same issue and indeed the 1st link offered (https://drive.google.com/file/d/0B1LaMEhefCBgYzNTOUxJZmtWQ0E/view) worked like a charm.
The second link is to download the "Intel platform flash tool lite", but I used my existing version of the Intel Phone Flash Tool (5.2.1-0) which worked fine with the image.
In other words, Corasman, it appears you have saved 2 people's life (or at least tablets) with your solution, so Thanks ! :good:
Regards.
Make that 3 people! Thank you so much corasman - your post has finally fixed my yoga 2 tablet, which I was sure would be going in the bin. Can't overstate how grateful I am - Cheers!
update 830f with 1050f rom?
updating 830f with 1050 rom? does it work?
hello. I have the same problem. I update OTA to lolipop. Since the table is slow, i tried flashing some ROM (which i cannot recall) and the tablet stopped working. Now, I am trying to flash the link you provided and it succeed. However after that i get blank Screen. what Could be wrong. My table is YT2 830LC. Please help
I am typing this all over again after my full report vanished. Do not have the patience of typing all that again. Suffice to say I had a similar situation with the boot failed EFI Hard Drive. Boot Successful - Enter Setup" message on my 830LC.
I had even found the bios restore tool for moving back from lollipop to kitkat but it too would hang. And attempts to flash lollipop would fail immediately with the same message as the OP, wrong device state.
So, in spite of it seeming completely counter-intuitive, I flashed the 1050F rom in the link shared by Corasman. Strange as it may seem, my tablet is now alive and working. No calling function, but it is working and calling itself a 1050F.
Now my research has to shift to whether the 830 LC rom can be flashed now.
i have a same problem with yoga 2 pro 1380f mr corasmancan help me
prabuddhadg said:
I am typing this all over again after my full report vanished. Do not have the patience of typing all that again. Suffice to say I had a similar situation with the boot failed EFI Hard Drive. Boot Successful - Enter Setup" message on my 830LC.
I had even found the bios restore tool for moving back from lollipop to kitkat but it too would hang. And attempts to flash lollipop would fail immediately with the same message as the OP, wrong device state.
So, in spite of it seeming completely counter-intuitive, I flashed the 1050F rom in the link shared by Corasman. Strange as it may seem, my tablet is now alive and working. No calling function, but it is working and calling itself a 1050F.
Now my research has to shift to whether the 830 LC rom can be flashed now.
Click to expand...
Click to collapse
i have same problem with my yoga 830lc this rom not work help me to run my tab agian
---------- Post added at 10:55 AM ---------- Previous post was at 10:47 AM ----------
corasman said:
This is the file you need
And this
Ignore the oops error warning, it's something to do with what G drive can scan.
Click to expand...
Click to collapse
hy sir downlod the rom from google drive but unable to download 2nd link (link not working)
i use latest intel flas tool light but the rom no flash to my device its show errors. plese sir help me to run my tab again