Hello
i have a note 3 which got bricked then i repaired brick and baseband issues . But currently Accelerometer and groscpe is not working. i visiually checked the hardware there is no sign of any damage.
At sensor hub test accelerometer continusly shows ;
ACC Raw Data - x 19, y: 84, z: 0
x-angle:12, y-angle: 77, z-angle: 0
Gyroscope Sensor continusly shows ;
GYROSCOPE: Y: 0, P: 0, R: 0
And device infor is ;
Model number
SM-9005
Android version
4.4.2
Baseband version
N9005XXUGNG1
Kernel version
3.4.0-1955971
[email protected] #1
Mon Jul 28 21:49:56 KST 2014
Build number
KOT49H.N9005XXUGNG1
SE for Android status
Enforcing
SEPF_SM-N9005_4.4.2_0016
Mon Jul 28 21:49:39 2014
Security software version
MDF v1.0 Release 3
i checked forums but i did not see a relevant issue forum(please referme if there is any i also dont like repeative threads ), my guess is that calibration folder is corrupted , so i would like to ask what could be the reason and how to fix ? (since i am electrical engineer i like to have detailed information )
Your helps and toughts will be appreciated.
Best regards.
KARABESK said:
Hello
i have a note 3 which got bricked then i repaired brick and baseband issues . But currently Accelerometer and groscpe is not working. i visiually checked the hardware there is no sign of any damage.
At sensor hub test accelerometer continusly shows ;
ACC Raw Data - x 19, y: 84, z: 0
x-angle:12, y-angle: 77, z-angle: 0
Gyroscope Sensor continusly shows ;
GYROSCOPE: Y: 0, P: 0, R: 0
And device infor is ;
Model number
SM-9005
Android version
4.4.2
Baseband version
N9005XXUGNG1
Kernel version
3.4.0-1955971
[email protected] #1
Mon Jul 28 21:49:56 KST 2014
Build number
KOT49H.N9005XXUGNG1
SE for Android status
Enforcing
SEPF_SM-N9005_4.4.2_0016
Mon Jul 28 21:49:39 2014
Security software version
MDF v1.0 Release 3
i checked forums but i did not see a relevant issue forum(please referme if there is any i also dont like repeative threads ), my guess is that calibration folder is corrupted , so i would like to ask what could be the reason and how to fix ? (since i am electrical engineer i like to have detailed information )
Your helps and toughts will be appreciated.
Best regards.
Click to expand...
Click to collapse
If it isn't hardware it should be fixable using a stock firmware. Use Phone INFO Samsung from play store to check what your CSC actually is and download an image from Sammobile.
Then shut off the phone, start Odin on PC, then after a while (I usually remove battery, hold down power for a bit to flatten the main board, then replace battery and use Home+Vol Down+Power to start phone into DL mode and connect to PC. Then flash the stock firmware and check if it's fixed.
Journyman16 said:
If it isn't hardware it should be fixable using a stock firmware. Use Phone INFO Samsung from play store to check what your CSC actually is and download an image from Sammobile.
Then shut off the phone, start Odin on PC, then after a while (I usually remove battery, hold down power for a bit to flatten the main board, then replace battery and use Home+Vol Down+Power to start phone into DL mode and connect to PC. Then flash the stock firmware and check if it's fixed.
Click to expand...
Click to collapse
Hmm ok. i will try this one when i dl it
Model SM-N9005
Model name GALAXY Note 3 LTE
Country Poland
Version Android 5.0
Changelist 3643614
Build date Wed, 25 Feb 2015 12:57:23 +0000
Product code XEO
PDA N9005XXUGBOB6
CSC N9005XEOGBOA4
İ hope it will work
i did flash still same issue
KARABESK said:
i did flash still same issue
Click to expand...
Click to collapse
Gyroscope selftest failz also
rest of the sensors works as intended. any idea ?
Has to be hardware .
Related
I flashed an official Samsung software through Odin, and after I finished, I found that I lost the IMEI number.
So I had to flash a new software through "Z3X Box" and it gives me a new IMEI. Since then every time I try to check for update I got this message:
"Failed to update software. Network or server error occurred. Try later or try using PC Kies"
Phone information:
Android version
4.4.2
Baseband version
N900XXUBMI2
Kernel version
3.4.39-694641
[email protected] #1
Tue Mar 4 14:03:13 KST 2014
Build number
KOT49H.N900XXUDNC1
SE for android status
Enforcing
SEPF_SM-N900_4.4.2_0005
Model number
Sm-n900
New IMIE
004999010640000
Old IMIE
359543056219419
Thanks for your help.
mashkuov said:
i flashed an official samsung software through odin, and after i finished, i found that i lost the imei number.
So i had to flash a new software through "z3x box" and it gives me a new imei. Since then every time i try to check for update i got this message:
"failed to update software. Network or server error occurred. Try later or try using pc kies"
phone information:
Android version
4.4.2
baseband version
n900xxubmi2
kernel version
3.4.39-694641
[email protected] #1
tue mar 4 14:03:13 kst 2014
build number
kot49h.n900xxudnc1
se for android status
enforcing
sepf_sm-n900_4.4.2_0005
model number
sm-n900
new imie
004999010640000
old imie
359543056219419
thanks for your help.
Click to expand...
Click to collapse
why do we care about you note 3 in our note 4 thread with 4.4.4 and above
Uniquebarbee said:
why do we care about you note 3 in our note 4 thread with 4.4.4 and above
Click to expand...
Click to collapse
I'm really sorry, my fault.
can somebody please move it because I don't know how to do it.
sorry again >_<
I copied it to the right section, can somebody please delete this one, sorry for the mistake. Thanks.
Sent from my Nexus 5
Dear XDA peoples.
Firstly I ask to humbly excuse my ignorance in these matters, but for a girl who grew up on tinkering with symbian Nokias I am finding the last problem with my S4 quite daunting.
I am hoping some kind soul on here can help me and yes I have spent hours searching for a solution I'm not just being lazy and I do understand the very basics.
I have an Australian delivered S4 i9505 and I took days to reads the forums on how to flash my s4 so I could have ultra power saving mode.
After reading the very helpful forums on these boards I managed to get the latest ECHOE ROM running and its amazing improvement on what I had before !
The only problem is that now everytime I hit the right standby button to go into standby it loses signal completely .
Again after checking the forums they explained that this is a known problem and one of the solutions is to simply force the phone on GSM only.
This does work but is not practical in reality as I need 3G to work for internet and coverage.
The guides also talk about making sure the "LTE" flag is set to true using ROOT explorer and it is.
I have also as the guides suggested loaded my "baseband" modem through ODIN again to no avail.
In the phone about box it displays :
Model Number : GT-I9505
Android version : 4.4.2
Baseband Version : I9505DVUBME4
Kernal Version : 3.4.104AELKernel-v6.3-Mainline
[email protected] #1
Thu Sep 25 21:2108 EEST 2014
Build Number : Echoe_illusion_KOT49H.I9505XXUGNJ8
SE for Android status : Permissive
Secure boot status : Samsung
Security Software version : MDF v1.0 Release 2
ROM version : Echoe ROM v36.1 S5 Port Part XI
ROM release date : 10 Novemeber 2014
ROM develeoper : friedrich420
In the echoe Rom faq : at echoerom dot com forward slash faq it does say
Q: I have poor connection and/or i keep losing connection occasionally when screen shuts. Is there a fix for this?
A: Yes. Flash MJ5 modem in Odin.
Again excuse my ignorance , but could a learned person actually elaborate on the above and it is applicable to my situation ?
Does this mean I need to flash a modem that is not specifically for my model ?
I sincerely apologise in advance if any of the above are moronic questions and a huge hug to all you smart people on this forum.
Bec88
same issue, same questions here ^-^ but using Imperium v14 ROM
It's not a moron question.
You lose the signal because I assume you are still on the old bootloader.
A. You can upgrade the bootloader (just flash a 4.4.2 stock rom), then reflash the custom rom you want.
or
B. You can flash a non-hlos/wifi fix modem (those are for the old bootloader).
Here you have some explanation:
http://forum.xda-developers.com/showpost.php?p=50787570&postcount=2548
http://forum.xda-developers.com/showthread.php?p=50965837
Thankyou !
Dear Lennyz1988,
Thanks for your rocket speed help, but when I explained losing signal, the WIFI is fine I lose the Carrier 3G signal.
And Lennyz please dont laugh, how do I know If I am on the old bootloader !
Bec
Thanks for the great help. I just installed the new bootloader and the modem and it works fine now
---------- Post added at 04:45 PM ---------- Previous post was at 04:44 PM ----------
angelbabybec88 said:
Dear Lennyz1988,
Thanks for your rocket speed help, but when I explained losing signal, the WIFI is fine I lose the Carrier 3G signal.
And Lennyz please dont laugh, how do I know If I am on the old bootloader !
Bec
Click to expand...
Click to collapse
Hi, I had also the issue that my 3G (mobile network) was off once I turned the screen off.
I just used the way on this link http://forum.xda-developers.com/showthread.php?p=50965837#post50965837
and installed with Odin:
Combined package - both modems in one flashable file.
GSM_Modem_XXUGNJ8_and_LTE_Modem_XXUGNJ8
Bootloader
BL_I9505XXUGNJ8_user_low_ship_MULTI_CERT
Now it is working again.
This is my phone model, will flashing axactly as you have stated work with my model .
Model: GT-I9505
Model name: GALAXY S4 LTE
Country: Australia
Version: Android 4.2.2
Changelist: 768421
Build date: Wed, 29 May 2013 16:05:23 +0000
Product Code: XSA
PDA: I9505XXUBMEA
CSC: I9505XSABME4
MODEM: I9505DVUBME4
angelbabybec88 said:
This is my phone model, will flashing axactly as you have stated work with my model .
Model: GT-I9505
Model name: GALAXY S4 LTE
Country: Australia
Version: Android 4.2.2
Changelist: 768421
Build date: Wed, 29 May 2013 16:05:23 +0000
Product Code: XSA
PDA: I9505XXUBMEA
CSC: I9505XSABME4
MODEM: I9505DVUBME4
Click to expand...
Click to collapse
It should work fine. Be aware of:
1. If you're using a custom ROM which has some sort of advanced power menu where you can select Reboot -> Download Mode... choose Power Off instead.
2. Now, press & hold the power, volume down and home button. When you're greeting with an informational screen, press volume up.
3. Connect the USB cable (not to a microwave oven).
4. Start Odin (preferably version 3.04 or 3.07). Make sure all checkboxes on the left hand side of the screen are NOT checked.
5. Select "PHONE" and link to the modem file you want to flash (modem.bin, modem.tar, modem.tar.md5).
6. Once the process is done (wait for the green box to turn green and display PASS), disconnect the USB cable and hold down the power button to reboot the phone.
I assume you are on the old bootloader, because you have an old modem. Thus you never updated to the new bootloader.
Flash a combined package and it should fix it.
All Fixed,
Thanks so much Lennyz & Co, it worked flawlessly.
xx
Bec
my device is note 3 china i think and have the following info
Model : SM-N9000
FCC ID : A3L SMN9000
SSN :- N9000GSMH
made in korea by samsung
=====================================
i was try to flash other rom than the original and i think i break it ,,
for my lucky i used MtkDroidTools v2.5.3 and made backup before i break it
any way ....... i can not flash the backup again or even cannot flash any rom in it
always have errors in SP flash tool about Enable DRAM
this error appear even when i try to use my original backup ( i think the wrong rom i tried did something ) , and also when try to format same error appaer .
any way i also get my SW & HW info before i make flashin ,,, as follow
AP = N9006XXU1ANCD
CP = N9006XXU1ANCE
CSC = N9006UUB1ANCD
RF = 2014.3.27
HW REV. = MP 0.800
................... can some one please help me in my problem . i need the exact rom of my phone and if there is any other way to flash ( may be odin) .
THANKS
my PHONE info file from MtkDroidTools v2.5.3 shows this data :
Hardware : MT6572 (UNIVERSAL5410 is Fake!)
Model : SM-N9006
Build number : JSS15J.N9006ZCUBMI5
Build date UTC : 20140505-074253
Android v : 4.3
Baseband v: MOLY.WR8.W1315.MD.WG.MP.V1, 2013/07/04 15:16
Kernel v : 3.4.0-1590669 ([email protected]) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #1 SMP Mon May 5 15:38:58 CST 2014
Uboot build v : -----
LCD Driver IC : 1-otm9605_qhd_dsi_vdo
decortiga said:
my device is note 3 china i think and have the following info
Model : SM-N9000
FCC ID : A3L SMN9000
SSN :- N9000GSMH
made in korea by samsung
=====================================
i was try to flash other rom than the original and i think i break it ,,
for my lucky i used MtkDroidTools v2.5.3 and made backup before i break it
any way ....... i can not flash the backup again or even cannot flash any rom in it
always have errors in SP flash tool about Enable DRAM
this error appear even when i try to use my original backup ( i think the wrong rom i tried did something ) , and also when try to format same error appaer .
any way i also get my SW & HW info before i make flashin ,,, as follow
AP = N9006XXU1ANCD
CP = N9006XXU1ANCE
CSC = N9006UUB1ANCD
RF = 2014.3.27
HW REV. = MP 0.800
................... can some one please help me in my problem . i need the exact rom of my phone and if there is any other way to flash ( may be odin) .
THANKS
my PHONE info file from MtkDroidTools v2.5.3 shows this data :
Hardware : MT6572 (UNIVERSAL5410 is Fake!)
Model : SM-N9006
Build number : JSS15J.N9006ZCUBMI5
Build date UTC : 20140505-074253
Android v : 4.3
Baseband v: MOLY.WR8.W1315.MD.WG.MP.V1, 2013/07/04 15:16
Kernel v : 3.4.0-1590669 ([email protected]) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #1 SMP Mon May 5 15:38:58 CST 2014
Uboot build v : -----
LCD Driver IC : 1-otm9605_qhd_dsi_vdo
Click to expand...
Click to collapse
!!!! 55 views and no one any answer OMG is my phone dead or what ?!!!!
please any help.
decortiga said:
!!!! 55 views and no one any answer OMG is my phone dead or what ?!!!!
please any help.
Click to expand...
Click to collapse
What's the problem with your phone?
Try to get your phones rom, why do you flashed other roms files.
Your now might be a ? now.
decortiga said:
!!!! 55 views and no one any answer OMG is my phone dead or what ?!!!!
please any help.
Click to expand...
Click to collapse
Your device is fake/clone. No one official firmware that you try to flash will work.
decortiga said:
my device is note 3 china i think and have the following info
Model : SM-N9000
FCC ID : A3L SMN9000
SSN :- N9000GSMH
made in korea by samsung
=====================================
i was try to flash other rom than the original and i think i break it ,,
for my lucky i used MtkDroidTools v2.5.3 and made backup before i break it
any way ....... i can not flash the backup again or even cannot flash any rom in it
always have errors in SP flash tool about Enable DRAM
this error appear even when i try to use my original backup ( i think the wrong rom i tried did something ) , and also when try to format same error appaer .
any way i also get my SW & HW info before i make flashin ,,, as follow
AP = N9006XXU1ANCD
CP = N9006XXU1ANCE
CSC = N9006UUB1ANCD
RF = 2014.3.27
HW REV. = MP 0.800
................... can some one please help me in my problem . i need the exact rom of my phone and if there is any other way to flash ( may be odin) .
THANKS
my PHONE info file from MtkDroidTools v2.5.3 shows this data :
Hardware : MT6572 (UNIVERSAL5410 is Fake!)
Model : SM-N9006
Build number : JSS15J.N9006ZCUBMI5
Build date UTC : 20140505-074253
Android v : 4.3
Baseband v: MOLY.WR8.W1315.MD.WG.MP.V1, 2013/07/04 15:16
Kernel v : 3.4.0-1590669 ([email protected]) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #1 SMP Mon May 5 15:38:58 CST 2014
Uboot build v : -----
LCD Driver IC : 1-otm9605_qhd_dsi_vdo
Click to expand...
Click to collapse
Try to flash the original one back.
But please make sure to connect your USB-Connector properly on the computer and to be sure, use an USB 2.0-Port.
I hope, this helped.
decortiga said:
my device is note 3 china i think and have the following info
Model : SM-N9000
FCC ID : A3L SMN9000
SSN :- N9000GSMH
made in korea by samsung
=====================================
i was try to flash other rom than the original and i think i break it ,,
for my lucky i used MtkDroidTools v2.5.3 and made backup before i break it
any way ....... i can not flash the backup again or even cannot flash any rom in it
always have errors in SP flash tool about Enable DRAM
this error appear even when i try to use my original backup ( i think the wrong rom i tried did something ) , and also when try to format same error appaer .
any way i also get my SW & HW info before i make flashin ,,, as follow
...
Click to expand...
Click to collapse
Near as I can tell from a quick Google, your phone SW is N9006ZCUBMI5 so you need to search for, and download that to flash. Being a Clone there doesn't seem to be much else available for it so that's pretty much your only shot I think.
Hannah Stern said:
Try to flash the original one back.
But please make sure to connect your USB-Connector properly on the computer and to be sure, use an USB 2.0-Port.
I hope, this helped.
Click to expand...
Click to collapse
i already try to flash back the original backup but still same error appear , Enable DRAM fail
Journyman16 said:
Near as I can tell from a quick Google, your phone SW is N9006ZCUBMI5 so you need to search for, and download that to flash. Being a Clone there doesn't seem to be much else available for it so that's pretty much your only shot I think.
Click to expand...
Click to collapse
i was search for rom with model number and downloaded about 5 version and all roms cannot be flashed due to same error of Dram fail
i will try to search again with the build number N9006ZCUBMI5 as you said ,
i will post the results
thanks
again same problem
Enable Dram Fail
what is this error slution OMG
even with the original backup !!!!
can some one please please give link for usb drivers of this model
because my pc dont recognize it .
may be that is the cause ?
decortiga said:
again same problem
Enable Dram Fail
what is this error slution OMG
even with the original backup !!!!
can some one please please give link for usb drivers of this model
because my pc dont recognize it .
may be that is the cause ?
Click to expand...
Click to collapse
Haha, and you flashed what then, when your phone isn't even connected? ?
Return and buy an original one
decortiga said:
again same problem
Enable Dram Fail
what is this error slution OMG
even with the original backup !!!!
can some one please please give link for usb drivers of this model
because my pc dont recognize it .
may be that is the cause ?
Click to expand...
Click to collapse
See
http://forum.xda-developers.com/showthread.php?t=2460126
Drivers samsung /support/ but its not a samsung .
still same error and i think i missed some thing in drivers and all i want is to flash my backup original rom that i made with MtkDroidTools v2.5.3
just please some one send me link of driver and guide to install them , i will be so appreciated
thanks again
please guys some help here or any idea ?
i need the exact preloader or even the complete rom of this devise :
Hardware : MT6572 (UNIVERSAL5410 is Fake!)
Model : SM-N9006
Build number : JSS15J.N9006ZCUBMI5
Build date UTC : 20140505-074253
Android v : 4.3
Baseband v: MOLY.WR8.W1315.MD.WG.MP.V1, 2013/07/04 15:16
Kernel v : 3.4.0-1590669 ([email protected]) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #1 SMP Mon May 5 15:38:58 CST 2014
Uboot build v : -----
LCD Driver IC : 1-otm9605_qhd_dsi_vdo
really i can not flash my backup and also my pc dont recognize the devise ( only show MTK com and it keeps connect and disconnect ) no ADB or any VCOM ports
and also my phone dont show charge icon when i connect to charger
i think it is because wrong preloader
so please some one upload for me correct preloader.bin and correct scatter file
Thanks agin.
I don't want to be a stick in the mud... but this forum is for original phones where people can actually provide help for.
This is the price you paid for getting a knock-off. Return it... if not possible, just gonna have to buy an original next time (from somewhere more reputable).
I'm hoping a mod closes this already.
We can't help you with fakes because they offer vastly different hardware (and software) from the originals. Thread closed.
Hi All I was wondering if somebody might be able to help me.
I was given an android tv box for xmas and recently it has been resetting itself everytime I try to use it.
I've tried doing a factory reset but same thing keeps happening so was going to do a firmware reset only problem is I'm unsure what numbers have to match to get the right firmware.
My Device is a :-
Tonbux
Model number:
MXQ
Android version:
4.4.2
Build number:
KOT49H.20150820 test-keys
Kernel version:
3.10.33
[email protected] #4
Fri Jun 26 12:34:17 cst 2015
I've tried loads of sites but none of them match the same Build number as my box.
I didn't want to use any of the other firmware that didn't match my Build number just incase I damaged the box, I am capable of doing the reset but only if some1 could confirm if the Build number has to be a complete match or if I'm able to use another I.
I found this latest 1 which is the closest to my number but no luck with exact match anywhere :
KOT49H.20150915 test-keys
Sept 28 2015
Help Appreciated thx in advance.
Fred
Can anyone jump in and provide some help? I'm having a similar issue as the OP. I have a generic Android TV box which is unusable with a lot of crapwares. I just want to erase everything and install a vanila version of Android on it. Here's some info of the box:
- CPU: Rockchip RK3066, 2x ARM [email protected] 1.61GHz
- GPU: Mali 400 MP
Edit: I can kind of get to the recovery mode but no menu appears, just the Andoid robot laying down and a red sign. Before that it shows CloudTVBox so I guess that's the (brand) name of the box!
Thanks a lot
Ok so after some research, I think my main issue now is that I don't have the recovery menu, only the Android robot lying and a red sign. Can anyone provide some help? Thanks
I think you need to research unbrick your device. If someone can tell me how to export my firmware I could send you mine. Here are my following specs down to the chipset (i had to open my box to find out).
Model Android Version Build Number Kernel Version Kernel
MXQ 4.4.2 KOT49H.20150720 test-keys 3.10.33 [email protected] #4 Fri Jun 26 12:34:17 CST 2015
Device Brand Model
LAN Pulse Electronics H1102NL
WiFi Realtek RTL8188EUS
USB Genesys Logic GL850G
RAM SkHynix h5tq4g63afr-pbc
hi guys, i have S6 edge+ SM-G9287 with a troubleshoot like freeze 3 secs and then normal again, very often,
this is my software info :
Android version : 6.0.1
Baseband version : G9287ZHU2BPH2
Kernel version :
3.10.61-8926938
[email protected]#1
Fri Aug 5 20 :06:46
Build number : MMB29K.G9287ZHU2BPH2
SE for Android status :
Enforcing
SEPF_SECMOBILE_6.0.1_0020
anyone can help me ?
or anyone know where i can find my firmware..?
doremonz26 said:
hi guys, i have S6 edge+ SM-G9287 with a troubleshoot like freeze 3 secs and then normal again, very often,
this is my software info :
Android version : 6.0.1
Baseband version : G9287ZHU2BPH2
Kernel version :
3.10.61-8926938
[email protected]#1
Fri Aug 5 20 :06:46
Build number : MMB29K.G9287ZHU2BPH2
SE for Android status :
Enforcing
SEPF_SECMOBILE_6.0.1_0020
anyone can help me ?
or anyone know where i can find my firmware..?
Click to expand...
Click to collapse
Flashing the stock firmware is easy and it fixes all ur issues 98% of times (depends if u wipe or not)
you can get your firmware files from
fw.updato.com(works really fast but sometimes is down
or
http://sammobile.com(is always up but y need an account and its slow)
And odin 3 the software needed to reflash stock firmware y can get it from here
Keep in mind that a full wipe from the recovery is recomended to solve all 100% of issues but there is a chance your issue could be fixed without a wipe.
Also you can flash the firmware from any country you like doesnt matter where ur from.
Hope this helped