Database Users

Note 3 Accelerometer gyroscope not working

Hello
i have a note 3 which got bricked then i repaired brick and baseband issues . But currently Accelerometer and groscpe is not working. i visiually checked the hardware there is no sign of any damage.
At sensor hub test accelerometer continusly shows ;
ACC Raw Data - x 19, y: 84, z: 0
x-angle:12, y-angle: 77, z-angle: 0
Gyroscope Sensor continusly shows ;
GYROSCOPE: Y: 0, P: 0, R: 0
And device infor is ;
Model number
SM-9005
Android version
4.4.2
Baseband version
N9005XXUGNG1
Kernel version
3.4.0-1955971
[email protected] #1
Mon Jul 28 21:49:56 KST 2014
Build number
KOT49H.N9005XXUGNG1
SE for Android status
Enforcing
SEPF_SM-N9005_4.4.2_0016
Mon Jul 28 21:49:39 2014
Security software version
MDF v1.0 Release 3
i checked forums but i did not see a relevant issue forum(please referme if there is any i also dont like repeative threads ), my guess is that calibration folder is corrupted , so i would like to ask what could be the reason and how to fix ? (since i am electrical engineer i like to have detailed information )
Your helps and toughts will be appreciated.
Best regards.

KARABESK said:
Hello
i have a note 3 which got bricked then i repaired brick and baseband issues . But currently Accelerometer and groscpe is not working. i visiually checked the hardware there is no sign of any damage.
At sensor hub test accelerometer continusly shows ;
ACC Raw Data - x 19, y: 84, z: 0
x-angle:12, y-angle: 77, z-angle: 0
Gyroscope Sensor continusly shows ;
GYROSCOPE: Y: 0, P: 0, R: 0
And device infor is ;
Model number
SM-9005
Android version
4.4.2
Baseband version
N9005XXUGNG1
Kernel version
3.4.0-1955971
[email protected] #1
Mon Jul 28 21:49:56 KST 2014
Build number
KOT49H.N9005XXUGNG1
SE for Android status
Enforcing
SEPF_SM-N9005_4.4.2_0016
Mon Jul 28 21:49:39 2014
Security software version
MDF v1.0 Release 3
i checked forums but i did not see a relevant issue forum(please referme if there is any i also dont like repeative threads ), my guess is that calibration folder is corrupted , so i would like to ask what could be the reason and how to fix ? (since i am electrical engineer i like to have detailed information )
Your helps and toughts will be appreciated.
Best regards.
Click to expand...
Click to collapse
If it isn't hardware it should be fixable using a stock firmware. Use Phone INFO Samsung from play store to check what your CSC actually is and download an image from Sammobile.
Then shut off the phone, start Odin on PC, then after a while (I usually remove battery, hold down power for a bit to flatten the main board, then replace battery and use Home+Vol Down+Power to start phone into DL mode and connect to PC. Then flash the stock firmware and check if it's fixed.

Journyman16 said:
If it isn't hardware it should be fixable using a stock firmware. Use Phone INFO Samsung from play store to check what your CSC actually is and download an image from Sammobile.
Then shut off the phone, start Odin on PC, then after a while (I usually remove battery, hold down power for a bit to flatten the main board, then replace battery and use Home+Vol Down+Power to start phone into DL mode and connect to PC. Then flash the stock firmware and check if it's fixed.
Click to expand...
Click to collapse
Hmm ok. i will try this one when i dl it
Model SM-N9005
Model name GALAXY Note 3 LTE
Country Poland
Version Android 5.0
Changelist 3643614
Build date Wed, 25 Feb 2015 12:57:23 +0000
Product code XEO
PDA N9005XXUGBOB6
CSC N9005XEOGBOA4
İ hope it will work

i did flash still same issue

KARABESK said:
i did flash still same issue
Click to expand...
Click to collapse
Gyroscope selftest failz also
rest of the sensors works as intended. any idea ?

Has to be hardware .

[Q] Help please all professionals

my device is note 3 china i think and have the following info
Model : SM-N9000
FCC ID : A3L SMN9000
SSN :- N9000GSMH
made in korea by samsung
=====================================
i was try to flash other rom than the original and i think i break it ,,
for my lucky i used MtkDroidTools v2.5.3 and made backup before i break it
any way ....... i can not flash the backup again or even cannot flash any rom in it
always have errors in SP flash tool about Enable DRAM
this error appear even when i try to use my original backup ( i think the wrong rom i tried did something ) , and also when try to format same error appaer .
any way i also get my SW & HW info before i make flashin ,,, as follow
AP = N9006XXU1ANCD
CP = N9006XXU1ANCE
CSC = N9006UUB1ANCD
RF = 2014.3.27
HW REV. = MP 0.800
................... can some one please help me in my problem . i need the exact rom of my phone and if there is any other way to flash ( may be odin) .
THANKS
my PHONE info file from MtkDroidTools v2.5.3 shows this data :
Hardware : MT6572 (UNIVERSAL5410 is Fake!)
Model : SM-N9006
Build number : JSS15J.N9006ZCUBMI5
Build date UTC : 20140505-074253
Android v : 4.3
Baseband v: MOLY.WR8.W1315.MD.WG.MP.V1, 2013/07/04 15:16
Kernel v : 3.4.0-1590669 ([email protected]) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #1 SMP Mon May 5 15:38:58 CST 2014
Uboot build v : -----
LCD Driver IC : 1-otm9605_qhd_dsi_vdo

decortiga said:
my device is note 3 china i think and have the following info
Model : SM-N9000
FCC ID : A3L SMN9000
SSN :- N9000GSMH
made in korea by samsung
=====================================
i was try to flash other rom than the original and i think i break it ,,
for my lucky i used MtkDroidTools v2.5.3 and made backup before i break it
any way ....... i can not flash the backup again or even cannot flash any rom in it
always have errors in SP flash tool about Enable DRAM
this error appear even when i try to use my original backup ( i think the wrong rom i tried did something ) , and also when try to format same error appaer .
any way i also get my SW & HW info before i make flashin ,,, as follow
AP = N9006XXU1ANCD
CP = N9006XXU1ANCE
CSC = N9006UUB1ANCD
RF = 2014.3.27
HW REV. = MP 0.800
................... can some one please help me in my problem . i need the exact rom of my phone and if there is any other way to flash ( may be odin) .
THANKS
my PHONE info file from MtkDroidTools v2.5.3 shows this data :
Hardware : MT6572 (UNIVERSAL5410 is Fake!)
Model : SM-N9006
Build number : JSS15J.N9006ZCUBMI5
Build date UTC : 20140505-074253
Android v : 4.3
Baseband v: MOLY.WR8.W1315.MD.WG.MP.V1, 2013/07/04 15:16
Kernel v : 3.4.0-1590669 ([email protected]) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #1 SMP Mon May 5 15:38:58 CST 2014
Uboot build v : -----
LCD Driver IC : 1-otm9605_qhd_dsi_vdo
Click to expand...
Click to collapse
!!!! 55 views and no one any answer OMG is my phone dead or what ?!!!!
please any help.

decortiga said:
!!!! 55 views and no one any answer OMG is my phone dead or what ?!!!!
please any help.
Click to expand...
Click to collapse
What's the problem with your phone?
Try to get your phones rom, why do you flashed other roms files.
Your now might be a ? now.

decortiga said:
!!!! 55 views and no one any answer OMG is my phone dead or what ?!!!!
please any help.
Click to expand...
Click to collapse
Your device is fake/clone. No one official firmware that you try to flash will work.

decortiga said:
my device is note 3 china i think and have the following info
Model : SM-N9000
FCC ID : A3L SMN9000
SSN :- N9000GSMH
made in korea by samsung
=====================================
i was try to flash other rom than the original and i think i break it ,,
for my lucky i used MtkDroidTools v2.5.3 and made backup before i break it
any way ....... i can not flash the backup again or even cannot flash any rom in it
always have errors in SP flash tool about Enable DRAM
this error appear even when i try to use my original backup ( i think the wrong rom i tried did something ) , and also when try to format same error appaer .
any way i also get my SW & HW info before i make flashin ,,, as follow
AP = N9006XXU1ANCD
CP = N9006XXU1ANCE
CSC = N9006UUB1ANCD
RF = 2014.3.27
HW REV. = MP 0.800
................... can some one please help me in my problem . i need the exact rom of my phone and if there is any other way to flash ( may be odin) .
THANKS
my PHONE info file from MtkDroidTools v2.5.3 shows this data :
Hardware : MT6572 (UNIVERSAL5410 is Fake!)
Model : SM-N9006
Build number : JSS15J.N9006ZCUBMI5
Build date UTC : 20140505-074253
Android v : 4.3
Baseband v: MOLY.WR8.W1315.MD.WG.MP.V1, 2013/07/04 15:16
Kernel v : 3.4.0-1590669 ([email protected]) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #1 SMP Mon May 5 15:38:58 CST 2014
Uboot build v : -----
LCD Driver IC : 1-otm9605_qhd_dsi_vdo
Click to expand...
Click to collapse
Try to flash the original one back.
But please make sure to connect your USB-Connector properly on the computer and to be sure, use an USB 2.0-Port.
I hope, this helped.

decortiga said:
my device is note 3 china i think and have the following info
Model : SM-N9000
FCC ID : A3L SMN9000
SSN :- N9000GSMH
made in korea by samsung
=====================================
i was try to flash other rom than the original and i think i break it ,,
for my lucky i used MtkDroidTools v2.5.3 and made backup before i break it
any way ....... i can not flash the backup again or even cannot flash any rom in it
always have errors in SP flash tool about Enable DRAM
this error appear even when i try to use my original backup ( i think the wrong rom i tried did something ) , and also when try to format same error appaer .
any way i also get my SW & HW info before i make flashin ,,, as follow
...
Click to expand...
Click to collapse
Near as I can tell from a quick Google, your phone SW is N9006ZCUBMI5 so you need to search for, and download that to flash. Being a Clone there doesn't seem to be much else available for it so that's pretty much your only shot I think.

Hannah Stern said:
Try to flash the original one back.
But please make sure to connect your USB-Connector properly on the computer and to be sure, use an USB 2.0-Port.
I hope, this helped.
Click to expand...
Click to collapse
i already try to flash back the original backup but still same error appear , Enable DRAM fail

Journyman16 said:
Near as I can tell from a quick Google, your phone SW is N9006ZCUBMI5 so you need to search for, and download that to flash. Being a Clone there doesn't seem to be much else available for it so that's pretty much your only shot I think.
Click to expand...
Click to collapse
i was search for rom with model number and downloaded about 5 version and all roms cannot be flashed due to same error of Dram fail
i will try to search again with the build number N9006ZCUBMI5 as you said ,
i will post the results
thanks

again same problem
Enable Dram Fail
what is this error slution OMG
even with the original backup !!!!
can some one please please give link for usb drivers of this model
because my pc dont recognize it .
may be that is the cause ?

decortiga said:
again same problem
Enable Dram Fail
what is this error slution OMG
even with the original backup !!!!
can some one please please give link for usb drivers of this model
because my pc dont recognize it .
may be that is the cause ?
Click to expand...
Click to collapse
Haha, and you flashed what then, when your phone isn't even connected? ?
Return and buy an original one

decortiga said:
again same problem
Enable Dram Fail
what is this error slution OMG
even with the original backup !!!!
can some one please please give link for usb drivers of this model
because my pc dont recognize it .
may be that is the cause ?
Click to expand...
Click to collapse
See
http://forum.xda-developers.com/showthread.php?t=2460126
Drivers samsung /support/ but its not a samsung .

still same error and i think i missed some thing in drivers and all i want is to flash my backup original rom that i made with MtkDroidTools v2.5.3
just please some one send me link of driver and guide to install them , i will be so appreciated
thanks again

please guys some help here or any idea ?
i need the exact preloader or even the complete rom of this devise :
Hardware : MT6572 (UNIVERSAL5410 is Fake!)
Model : SM-N9006
Build number : JSS15J.N9006ZCUBMI5
Build date UTC : 20140505-074253
Android v : 4.3
Baseband v: MOLY.WR8.W1315.MD.WG.MP.V1, 2013/07/04 15:16
Kernel v : 3.4.0-1590669 ([email protected]) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #1 SMP Mon May 5 15:38:58 CST 2014
Uboot build v : -----
LCD Driver IC : 1-otm9605_qhd_dsi_vdo
really i can not flash my backup and also my pc dont recognize the devise ( only show MTK com and it keeps connect and disconnect ) no ADB or any VCOM ports
and also my phone dont show charge icon when i connect to charger
i think it is because wrong preloader
so please some one upload for me correct preloader.bin and correct scatter file
Thanks agin.

I don't want to be a stick in the mud... but this forum is for original phones where people can actually provide help for.
This is the price you paid for getting a knock-off. Return it... if not possible, just gonna have to buy an original next time (from somewhere more reputable).
I'm hoping a mod closes this already.

We can't help you with fakes because they offer vastly different hardware (and software) from the originals. Thread closed.

Galaxy S5 SCL23 (SM-G900J)

Hello.
I just recently got Galaxy S5 which appears to be only sold in Japan. There's some custom firmware installed on it which prevents Android to be updated. Phone doesn't have SIM locked, so any SIM card can be used.
Because the forum doesn't allow me to post link to a screenshot which shows firmware info I'll just write it down.
Android version:
4.4.2
Baseband version:
SCL23KDU1BNE4
Kernel version:
3.4.0
[email protected] #1
Wed May 14 19:59:35 KST 2014
Build number:
SCL23KDU1BNE4
SE for Android status:
Enforcing
SEPF_SCL23_4.4.2_0011
Wed May 19:59:13 2014
Hardware version:
G900J.07
Security software version:
MDF v1.0 Release 2
VPN v1.4 Release 1
Click to expand...
Click to collapse
I'd like to completely wipe this firmware from the device, replace it with the latest Android version (6.0?) and root it. At first I'd like to know if it's even possible to do any kind of firmware changes on this model and what exactly do I need to perform the update/root.
Thanks.

Doesn't look like there is a 6.0 stock ROM for it, but you can upgrade to 5.0 here
http://updato.com/firmware-archive-select-model?r=&v=&q=SCL23
Flash with ODIN (Instructions all over the forum many times)

Okay, instructions on updato seems quite easy to follow so that shouldnt be a problem. Is there any recommended tool for root? I've found a lot of them and I really don't want to mess something up.
PS: How come there's no stock ROM for 6.0 even tho it's been mentioned in some articles that SCL23 model is also supported by Marshmallow update?

Anyone?

Okay, update to 5.0 passed without any issues. There are some default japanese applications on the phone which I cannot uninstall, is it possible to get rid of those somehow?

I have the same device Do you update succeeded or not

I installed Android 6.0.1 and the network was missing help someone Galaxy scl23 or give the firmware 4.4.2 or help to find the GSM network

zaza66 said:
I installed Android 6.0.1 and the network was missing help someone Galaxy scl23 or give the firmware 4.4.2 or help to find the GSM network
Click to expand...
Click to collapse
Go to this link & download 4.4.2 then follow this tutorial.
Make sure to use key input from the options & use capital letters where needed. All being well you will have everything working again.
Make sure not to use any download manager for the download link. File gets about 100kbps so it'll take a few hours but you will get it.
I did the above then rooted the phone & flashed correct TWRP version to it then flashed 5.0 Lollipop SpaceX rom here. Everything working good & no loss of service on reset or reboot.
Hope it helps

Installing stock ROM on SM-G532F

So guys I have flashed TWRP on my Grand Prime Plus through Odin. And now I need to find a stock ROM for my phone.
My question is:
Does the base version (and build version as well) of the ROM you're downloading need to be same to what it used to be before??
This here are some specifications of my phone right now:
Android Version
6.0.1
[Marshmallow]
Baseband Version
G532FXXU1AQB3
Kernel version
3.18.19-10802954
[email protected] #1
Tue Feb 28 13:18:58 KST 2017
Build Number
MMB29T.G532FXWU1AQB5
SE for Android Status
Enforcing
SEPF_SECMOBILE_E_6.0.1_0034
Tue Feb 28 13:48:25 2017
Security Software Version
ASKS v1.2_161011
Knox version
....
Android Security Patch Level
1 March 2017
Click to expand...
Click to collapse
Can someone tell me if the base version and the Build Number needs to be same for downloading a new ROM or not??
And where can I find the best ROM for my phone??
Edit: And does the region of the ROM you're about to download needs to be the same as the region you're living at? Does it make any different?
Also, how do I make a backup for the already installed OS? What do MUST make backup of out of:
Boot
Recovery
EFS
Cache
System
Data
Misc
Modem
System Image
I don't really care about losing data, I just don't want to lose my previous already installed OS while trying to flash a new stock ROM. So what do I make backup of out of the aforementioned?
Thanks.

Where is stock frimware link?

G950F : which one of these 5 last firmwares is rootable ?

Hi, since the end of AdHell3 (because of Knox licenses) I've decided to update to the latest rootable stock firmware... Which should I install & root please ?
- Build Number : G950FXXU5DSFB
Android version : Pie(Android 9)
Release Date : 2019-07-02
Security patch level : 2019-07-01
- Build Number : G950FXXS5DSF1
Android version : Pie(Android 9)
Release Date : 2019-06-25
Security patch level : 2019-06-01
- Build Number : G950FXXU4DSE4
Android version : Pie(Android 9)
Release Date : 2019-06-10
Security patch level : 2019-05-01
- Build Number : G950FXXS4DSE1
Android version : Pie(Android 9)
Release Date : 2019-05-21
Security patch level : 2019-05-01
- Build Number : G950FXXU4DSDA
Android version : Pie(Android 9)
Release Date : 2019-05-10
Security patch level : 2019-04-01

Remember once u install june or july update u can't downgrade anymore to earlier pie or oreo builds.

Thx for your reply but i know Since I'm satisfied with Android 9, it's not a problem (about 48h of battery life with the stock rom installed).
But no one can answer to my question please ? A major part of this forum is dedicated to root and no one can answer me ?

no answer so I will root the older one.... Useless post, last time I'm asking help here

I think you can root all

xozeus said:
no answer so I will root the older one.... Useless post, last time I'm asking help here
Click to expand...
Click to collapse
I can root any firmware as long u follow the guide on rooting , nothing that big changed from oreo to pie ect

OK thx for your replies Scorpionea and Mario. I will follow these guides to root :
forum.xda-developers.com/samsung-a-series-2017/how-to/guide-root-install-twrp-samsung-t3747535
forum.xda-developers.com/galaxy-s8/samsung-galaxy-s8--s8-cross-device-development/fix-data-mount-fix-s8-twrp-oreo-t3769254
Another one to suggest me ?

DON'T FLASH the firmware G950FXXU5DSFB if you want to install TWRP, it seems it's not compatible with this version.
I tried to flash it on my phone and now the recovery partition is buged.
EDIT : I was wrong. After reboot, the system needed to install some updates (maybe because of the upgrade of the bootloader - v4 to v5) that's why I could not flash TWRP. After a full boot (I've done the initial setup) and then a reboot, I was able to flash recovery.

xozeus said:
DON'T FLASH the firmware G950FXXU5DSFB if you want to install TWRP, it seems it's not compatible with this version.
I tried to flash it on my phone and now the recovery partition is buged.
Click to expand...
Click to collapse
What happend?
Make sure u do all the steps correctly or else won't work .

I can confirm because I've tested to flash and root all these firmwares : it works for all of them. Now I'm searching if it is TWRP or DM-verity or RMM-state which modifies and pollutes the settings menu by adding some useless entries... (see the screenshots)