Database Users

[Q] Back to stock or not, stock ROM failure.

Hi All, I think I have read everything and tried all methods and I have now run out of ideas. Hoping it's something simple i'm missing.
So my I9505 has been rooted for some time and I would now like to return to stock to give the phone to my mother-in-law.
I am able to access twrp custom recovery and stock recovery modes, I'm able to flash custom rome using twrp. However I don't seem to be able to flash a stock rom using the method below:
http://forum.xda-developers.com/showthread.php?t=2265477&highlight=complete(write)+operation+failed
My phone is currently up and running in the following state:
Android Version: 4.4.2
BaseBand Version: I9505XXUFNAD
Kernel Version: 3.4.0.2091210 [email protected] 1
Build Number: Echoe_Illusion_KOT49H.I9505XXUGNG2
SE for Android Status: Enforcing SEPF_GT-I9509_4.4.2_0018
Secure boot status: Type: Samsung
Security software version: MDFF v1.0 Release 2
Every time I try the odin method above to install stock ROM i get to Complete Write Operation Failed.
I have tried different odin versions, different machines, different cables.
The two ROMs I have tried to flash are:
I9505XXUEMK9_I9505EVREMK1_I9505XXUEMK9_HOME.tar.md5
I9505XXUFNB9_I9505BTUFNE1_I9505XXUFNB9_HOME.tar.md5
Any ideas please
Hopefully something simple I'm doing wrong.

Might be the file u downloaded be corrupt
Try downloading again then wipe dalvik cache and flash.
Sent from my A210 using XDA Free mobile app

rutwikkiller said:
Might be the file u downloaded be corrupt
Try downloading again then wipe dalvik cache and flash.
Sent from my A210 using XDA Free mobile app
Click to expand...
Click to collapse
Thanks, I have done this several times. Still nothing, very frustrating and time consuming

Post the complete Odin log.
Try only 4.4.2 roms and nothing below that.
http://samsung-updates.com/device/?id=GT-I9505
Pick one of the latest and try again.

Lennyz1988 said:
Post the complete Odin log.
Try only 4.4.2 roms and nothing below that.
Pick one of the latest and try again.
Click to expand...
Click to collapse
Cheers, i'll try another one and post the log.

s4fog said:
Cheers, i'll try another one and post the log.
Click to expand...
Click to collapse
Ok I have tried another one from the link supplied:
Failed again here is the odin log and txt from phone screen:
Odin Mode
Product Name: GT-I9505
Current Binary: Custom
System Status: Custom
Knox Kernel Lock: 0x0
Knox Warranty Void: 0x1
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enabled
eMMC Burst Mode: Enabled
START [224, 1440]
BAR [240, 1440]
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNB9_I9505BTUFNE1_I9505XXUFNB9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

s4fog said:
Ok I have tried another one from the link supplied:
Failed again here is the odin log and txt from phone screen:
Odin Mode
Product Name: GT-I9505
Current Binary: Custom
System Status: Custom
Knox Kernel Lock: 0x0
Knox Warranty Void: 0x1
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enabled
eMMC Burst Mode: Enabled
START [224, 1440]
BAR [240, 1440]
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNB9_I9505BTUFNE1_I9505XXUFNB9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Can anyone help with this please?

s4fog said:
Can anyone help with this please?
Click to expand...
Click to collapse
You should download same but new firmware agian via sammobile and try to reflash with other pc...
Sent from my GT-I9500 using XDA Premium 4 mobile app

s4fog said:
Ok I have tried another one from the link supplied:
Failed again here is the odin log and txt from phone screen:
Odin Mode
Product Name: GT-I9505
Current Binary: Custom
System Status: Custom
Knox Kernel Lock: 0x0
Knox Warranty Void: 0x1
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enabled
eMMC Burst Mode: Enabled
START [224, 1440]
BAR [240, 1440]
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNB9_I9505BTUFNE1_I9505XXUFNB9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
It just looks like a standard Odin error.
- Make sure Kies is not running in the background
- Different cable
- Different pc

Lennyz1988 said:
It just looks like a standard Odin error.
- Make sure Kies is not running in the background
- Different cable
- Different pc
Click to expand...
Click to collapse
Hooray!!!! Well I tried another PC, and for some reason this time it has worked. Nothing different about the three machines. Same software, same ROMs, same process. Two wouldn't work, one did.
Thanks again for pushing me to try another machine.

[Q] Rooted SCH-i545 Verizon s4 stuck in download mode - Fail (AUTH) In odin

So, I was trying to flash my custom rom to my SCH-i545 (Verizon S4) and now it's stuck in download mode!
It's an NC5 and android 4.4.2 (I think) . Pretty much every forum i visited said to use TWRP and Safestrap, but after flashing the custom recovery and rebooting, it would not leave download mode. Tried flashing a custom recovery with odin, and it fails.
Phone output:
Could not do normal boot.
PRODUCT NAME: SCH-i545
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x0
CSB-CONFIG-LSB:0x30
WRITE PROTECTION: Enable
eMMC BURST MODE: enabled
START [224,1440]
SW REV. CHECK FAIL : fused : 6, Binary : 1
Odin output:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> VRUAMDK_NoWipe.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> NON-HLOS.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> aboot.mbn
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Tried the recovery mode combo at least 20 times, to no avail. Any help for this noob?

Nevermind, i'm an idiot. I had the wrong .tar.md5

SPH-L720 - Trying To Return To Stock. aboot.mbn operation failed

I am trying to get back to stock firmware after using a custom 5.0.2 ROM. I've tried about everything I could find on forums/website and have come up empty handed. I have tried all the general stuff... USB Cables, USB Ports, Computers, etc. In the process of trying to flash back I tried going back to an older version of android which I guess was a bad idea, because that breaks the sound because of KNOX. ¯\_(ツ)_/¯
When trying to flash MJA with Odin this is what I get.
This is what I get on the phone screen.
ODIN MODE
PRODUCT NAME: SPH-L720
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x1
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enabled
eMMC BURST MODE: enabled
START [224, 1448]
SW REV. CHECK FAIL : fused : 5, Binary : 4
This is what shows up in Odin's log window.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUEMJA_L720SPTEMJA_L720VPUEMJA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

anyone? :\

Anyone?

http://forum.xda-developers.com/showthread.php?t=3025279

Help flashing stock firmware

I am a noob at this, so pardon me for my ignorance. After unrooting my Note 3 i am unable to update my firmware OTA or with Kies, even after factory resetting it did not work. After doing some research i learned that i have to flash my phone with stock firmware using odin(in order to get my phone back to normal). Do i have to flash the original firmware that my phone came with, or can i just flash it with the most up to date stock firmware that i want?

Jaxxxed said:
I am a noob at this, so pardon me for my ignorance. After unrooting my Note 3 i am unable to update my firmware OTA or with Kies, even after factory resetting it did not work. After doing some research i learned that i have to flash my phone with stock firmware using odin(in order to get my phone back to normal). Do i have to flash the original firmware that my phone came with, or can i just flash it with the most up to date stock firmware that i want?
Click to expand...
Click to collapse
You can flash the same build fw or the latest. Install 'samsung phone info' app to check your csc. You can even use the app to download the fw. But in case downloading takes forever to complete, you may use 'samsung firmware downloader'. It's a windows utility tool to download fw from sammobile.
Sent from my SM-N920C

When i attempted to use Odin, the flashing failed. here is the Odin log:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900AUCUBMI9_N900AATTBMI9_N900AUCUBMI9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sbl1.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone still works fine, and i have everything set up properly so that my phone can be flashed. so, im not sure whats going wrong.

Jaxxxed said:
When i attempted to use Odin, the flashing failed. here is the Odin log:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900AUCUBMI9_N900AATTBMI9_N900AUCUBMI9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sbl1.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone still works fine, and i have everything set up properly so that my phone can be flashed. so, im not sure whats going wrong.
Click to expand...
Click to collapse
It's N900?. Try different fw.
In download mode does it show reactivation lockn?
Sent from my SM-N920C

Rosli59564 said:
It's N900?. Try different fw.
In download mode does it show reactivation lockn?
Sent from my SM-N920C
Click to expand...
Click to collapse
Here is what my phone says in download mode:
Odin Mode
Product name: SM-N900A
Current Binary: Samsung official
System status: custom
Knox kernel lock: 0x0
Knox warranty void: 0x0
Qualcomm Secure boot: enable(csb)
RP SWREV: S2, T2, A2, A2, P2
Write protection:enable

The n900a is an att note 3.

Screwed up flashing my Samsung Galaxy Note 4

The phone would start and all of a sudden shut off and either stay off or it would turn back on but go into the download mode, and very rarely it would turn back on properly, so being the hard headed 20 year old i am i tried to flash it without consulting help first
i have no idea what i did but now the device only loads into download mode (if it even turns on) ive tried to flash it properly now and it comes up with an error
ODIN log:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 3431 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> sbl1.mbn
<ID:0/005> rpm.mbn
<ID:0/005> tz.mbn
<ID:0/005> sdi.mbn
<ID:0/005> NON-HLOS.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Write)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
what it says on the phone:
ODIN MODE (HIGH SPEED) {in red}
PRODUCT NAME: SM-N910F {in white}
CURRENT BINARY : Samsung Official {in white}
SYSTEM STATUS: Official {in white}
REACTIVATION LOCK: Off {in white}
KNOX WARRANTY VOID: 0x0 {in white}
QUALCOMM SECUREBOOT: Enabe (csb) {in grey}
RP SWREV: S1,T1,R1,A1,P1 {in grey}
SECURE DOWNLOAD: Enable {in blue}
UDC START {in red}
ODIN: flash write failure {in red}
Downloading...
Do not turn off target!!
{a progress bar that is frozen}(ive left it over night and it hasn't moved an inch)
I know this was me being hard headed and being stupid thinking it is simple but any help would be much appreciated, thank you in advance
PS
the model of the note 4 is :SM-N910F
PPS if i try to flash it again the odin log says:
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 3431 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)

Hope it doesn't have an emmc problem.
Which files did you try to flash or was it just one?
If they latter use samfirmtool to download multiple part stock ROM by checking "binary nature" in its options.
As you are flashing one older ROM an older Odin might hekp as well not to mention other cables/USB ports.

it looks VERY emmc issue
and since you did not seek to get educated first, before doing anything... well you end up here
we try to help
so
read here, maybe it will work for you